is a registered trademark of Netis Corporation. Other trademarks and trade
names may be used in this document to refer to either the entities claiming the marks
and names or their products.
Reproduction in any manner without the permission of Netis Corporation is strictly
forbidden
All the information in this document is subject to change without notice.
USA/Canada Technical Support
Phone: 1-866-71-network or 1-866-716-3896 (free in USA & Canada)
E-mail: usa_support@netis-systems.com
2
150Mbps/300Mbps Wireless-N AP / Repeater / Router client User Manual
150Mbps/300Mbps Wireless-N AP / Repeater / Router clientUser Manual
1. Introduction
1.1. Product Overview
150Mbps/300Mbps Wireless-N AP/ Repeater/ Router client is dedicated to Small
Office/Home Office (SOHO) Wireless network solution. It is 4 in 1 network device, which
combines wireless access point, firewall, 4-port Switch and the NAT-Router. It provides up to
150Mbps/300Mbps data transmission rate in 2.4GHz frequency, complies with IEEE 802.11n,
IEEE 802.11g and IEEE802.11b and backwards compatible with all IEEE 802.11n/g/b
devices. And the router also supports wireless LAN up to 128-bit WEP, WPA/WPA2
encryption security. The 150Mbps/300Mbps Wireless-N AP/ Repeater / Router client also
provides WEB and Remote Management and system log so that network administrators can
manage and monitor the network in real time.
The 150Mbps/300Mbps Wireless-N AP/ Repeater/ Router client also provides a hardware
WPS (Wi-Fi protected setup) button, which helps you setup a secure wireless network in a
snap. The button lets you activate the wireless protection easily.
1.2. Main Features
Comply with IEEE802.11n/g/b, IEEE802.3 10Base-T, IEEE802.3u 100Base-TX
standards
Support DHCP Client, PPPoE Client, Static IP, L2TP, PPTP
Support multi-wireless mode: AP, WDS, AP+WDS, repeater, client, etc.
Support static ARP, MAC filtering, IP access control, DNS filter
Support FTP, PPTP and L2TP pass through
Support UPNP (universal plug and play)
Upgradeable firmware for future functions
WPS button can easily setup a secure network
Support WMM
Support data encryption mode: WEP, WPA, WPA2
Support DMZ
6
150Mbps/300Mbps Wireless-N AP / Repeater / Router clientUser Manual
0° to 40° C (operating)
-40° to 70° C (storage)
Humidity
10% to 90 % non-condensing (operating)
5% to 90% non-condensing (storage)
Power
DC 9V
7
150Mbps/300Mbps Wireless-N AP / Repeater / Router clientUser Manual
2. Hardware Installation
2.1. System Requirement
Minimum Requirements:
Broadband (DSL/Cable) modem and service with Ethernet port
802.11n b/g/n wireless adapter or Ethernet adapter and cable for each computer
Internet Explorer® 5.0, Firefox® 2.0 or Safari® 1.4 or higher
2.2. Panel
Front panel
Figure 2-1
LED Function
8
150Mbps/300Mbps Wireless-N AP / Repeater / Router clientUser Manual
SYS
WPS
WAN
1X-4X
Rear panel
ON and Off Abnormal
Flashing Normal
Flashing
WPS is running
slowly
OFF WPS is not running
On WAN Connection normal
Flashing Data transmitting
Off WAN Connection abnormal
On LAN Connection normal
Flashing Data transmitting
Off LAN Connection abnormal
Figure 2-2
Description Function
Connect to Power adapter, please don’t use the unknown
SYS
power adapter, otherwise your device may be damaged.
Default Restore settings
WPS “WPS” Encryption button
WAN Internet access
1X-4X Connect with computer NIC or Ethernet device
2.3. Restore to factory configuration
If the router ever freezes in a setting change process or if you can’t access it because you can’t
remember the IP you have given it or other problem, you may have to utilize the reset button
on the back of the router to put it back to factory settings. You have to press and hole this
9
150Mbps/300Mbps Wireless-N AP / Repeater / Router clientUser Manual
button for a few seconds (2-6s) with a pencil when it is working, then release and it will
restore settings to the factory configuration.
The other way to restore factory settings is through the same user interface used in setup.
Click on ‘System management’- ‘Restore’, and click on the ‘Restore’ button.
2.4. Hardware Installation Procedures
The procedures to install the 150Mbps/300Mbps Wireless-N AP/ Repeater / Router client
please refers to the following picture
Figure 2-3
Attach one end of an Ethernet cable to your computer’s Ethernet port, and the other end
to one of the LAN ports of your router.
Connect another Ethernet cable from your Cable/DSL modem to the WAN port of your
router.
Connect the single DC output connector of the power adapter to the power jack on the
back of the router and plug the Power Adapter into an AC outlet.
10
150Mbps/300Mbps Wireless-N AP / Repeater / Router clientUser Manual
3. Login
You can manage the 150Mbps/300Mbps Wireless-N AP/ Repeater / Router client through
the Web browser-based configuration utility. To configure the device via Web browser, at least
one properly configured computer must be connected to the device via Ethernet or wireless
network. The 150Mbps/300Mbps Wireless-N AP/ Repeater / Router client is configured
with the default IP address of 192.168.1.1 and subnet mask of 255.255.255.0 and its DHCP server is enabled by default. Before setting up the Router, make sure your PCs are
configured to obtain an IP address automatically from the Router by the steps below.
3.1. Configure computer
3.1.1. Windows 98/Me
1. Go to Start Settings Control Panel.
2. Find and double-click the Network icon. The Network dialog box appears.
3. Click the Configuration label and ensure that you have network card.
4. Select TCP/IP. If TCP/IP appears more than once, please select the item that has an arrow
“” pointing to the network card installed on your computer. DO NOT choose the instance of
TCP/IP with the words “Dial Up Adapter” beside it.
5. Click Properties. The TCP/IP Properties dialog box appears.
6. Ensure the Obtain IP Address Automatically is checked.
7. From the WINS Configuration dialog box, Ensure that Disable WINS Resolution is
checked.
8. From the Gateway dialog box, remove all entries from the Installed gateways by selecting
them and clicking Remove.
9. From the DNS Configuration dialog box, remove all entries from the DNS Server Search
Order box by selecting them and clicking Remove. Remove all entries from the Domain
Suffix Search Order box by selecting them and clicking Remove. Click Disable DNS.
10. Click OK, back to Network Configuration dialog box
11. Click OK, if prompted to restart, click YES.
11
150Mbps/300Mbps Wireless-N AP / Repeater / Router clientUser Manual
3.1.2. Windows 2000
Please follow the steps below to setup your computer:
1. Go to Start Settings Control Panel
Figure 3-1
2. Double click the icon Network and Dial-up Connections
3. Highlight the icon Local Area Connection, right click your mouse, and click Properties
12
150Mbps/300Mbps Wireless-N AP / Repeater / Router clientUser Manual
Figure 3-2
4. Highlight Internet Protocol (TCP/IP), and then press Properties button
Figure 3-3
5. Choose Obtain an IP address automatically and Obtain DNS server address automatically,
and then press OK to close the Internet Protocol (TCP/IP) Properties window
13
150Mbps/300Mbps Wireless-N AP / Repeater / Router clientUser Manual
Figure 3-4
6. Press OK to close the Local Area Connection Properties window
Figure 3-5
3.1.3. Windows XP
Please follow the steps below to setup your computer:
1. Go to Start Settings Control Panel
14
150Mbps/300Mbps Wireless-N AP / Repeater / Router clientUser Manual
2. Click Network and Internet Connections
Figure 3-6
3. Click Network Connections
Figure 3-7
4. Highlight the icon Local Area Connection, right click your mouse, and click Properties
15
150Mbps/300Mbps Wireless-N AP / Repeater / Router clientUser Manual
Figure 3-8
5. Highlight Internet Protocol (TCP/IP), and then press Properties button
Figure 3-9
6. Choose Obtain an IP address automatically and Obtain DNS server address automatically,
and then press OK to close the Internet Protocol (TCP/IP) Properties window
16
150Mbps/300Mbps Wireless-N AP / Repeater / Router clientUser Manual
Figure 3-10
7. Press OK to close the Local Area Connection Properties window
Figure 3-11
3.1.4. Windows V ista
Please follow the steps below to setup your computer:
1. Go to Start Settings Control Panel
17
150Mbps/300Mbps Wireless-N AP / Repeater / Router clientUser Manual
2. Click Network and Sharing Center
3. Click Manage Network Connections
Figure 3-12
Figure 3-13
4. Highlight the icon Local Area Connection, right click your mouse, and click Properties
18
Loading...
+ 42 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.