WF-2409
300Mbps High
Performance Wireless-N
Broadband Router
Quick Installation Guide
V1.1
2011-06-23
WF-2409 Quick Installation Guide
1
Certification
FCC CE
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-Consult the dealer or an experienced radio/TV technician for help.
T o assure cont inued complia nce, any changes or m odific ations no t expr essly approv ed by the party
responsible for compliance could void the user’ s authority to operate this equipm ent. (Example- use
only shielded interface cables when connecting to computer or peripheral devices)
FCC Radiation Exposure Statement
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled
environment. This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
This equ ipm ent should be i nstalled an d operate d with a m inimum distanc e
of 20 centimeters between the radiator and your body.
This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause
undesired operation.
Caution!
The manufacturer is not responsible for any radio or TV interference caused by unauthorized
modifications to this equipment. Such modifications could void the user authority to operate the
equipment.
WF-2409 Quick Installation Guide
2
Package Contents
The following items should be found in your package:
300Mbps High Performance Wireless-N Broadband Router
Power Adapter
Quick Installation Guide
3 Antennas
CD-ROM
Ethernet Cable
Make sure that the package contains above items. If any of the above items is missing or
damaged, please contact the store you bought this product from.
Before You Begin
Minimum Requirements:
Broadband (DSL/Cable) modem and service with Ethernet port
802.11b/g/n wireless adapter or Ethernet adapter and cable for each computer
Internet Explorer
，
® 5.0 Firefox®2.0 or Safari® 1.4 or higher
Brand and Copyright Announcement
Copyright © 2010 Netis Corporation.
All rights reserved
is a registered trademark of Netis Corporation. Other trademarks and trade
names may be used in this document to refer to either the entities claiming the marks and
names or their products.
Reproduction in any manner without the permission of Netis Corporation is strictly
forbidden
All the information in this document is subject to change without notice.
USA/Canada Technical Support
Phone: 1-866-71-network or 1-866-716-3896 (free in USA & Canada)
E-mail: usa_support@netis-systems.com
WF-2409 Quick Installation Guide
3
1. Hardware Installation Procedur e
The procedures to install the WF-2409 please refer to Figure 1-1.
Figure 1-1
Step 1 connecting your computer to the LAN port.
Attach one end of the Ethernet cable with RJ-45 connector to your hub, switch or a computer’s
Ethernet port, and the other end to one of the LAN ports of your WF-2409.
Step 2 Connecting Cable/ADSL Modem to the WAN port.
Connect the Ethernet cable attaching to your Cable/ADSL modem to the WAN port of your
WF-2409.
Step 3 connecting the power adapter.
Connect the single DC output connector of the power adapter to the power jack on the side of
the WF-2409. Then plug the Power Adapter into an AC outlet.
Step 4 Power on the following devices in this order:
Cable/ADSL modem, Router, and PCs
2. Login
You can manage the WF-2409 through the Web browser-based configuration utility. To
configure the device via Web browser, at least one properly configured computer must be
connected to the device via Ethernet or wireless network. The WF-2409 is configured with the
default IP address of 192.168.1.1 and subnet mask of 255.255.255.0 and its DHCP server is
enabled by default. Before setting up the Router, make sure your PCs are configured to obtain
WF-2409 Quick Installation Guide
4
an IP address automatically from the Router by the steps below.
2.1. Configure computer (Windows 7)
Please follow the steps below to setup your computer:
1. Go to Start Settings Control Panel
2. Click Network and Sharing Center
Figure 2-1
3. Click Manage Network Connections
Figure 2-2
4. Highlight the icon Local Area Connection, right click your mouse, and click Properties
Loading...