Manual
Uniha n UPW L6 0 3 1 H 2
1 .Gener al De scr iption
The UPWL6031 H2 wireless m odule is a fu lly assem bled and tested general-purpose
m odule using the BCM4331w ireless System - on-Chip(SoC). The module cont ains
BCM4331 chip and all other necessar y com ponents to operat e t he UPWL6031 H2.
For det ailed inform ation on the UPWL6031 H2 com ponent it self, ref er t o t h e
UPWL603 1H2 dat asheet.
2 . Fe a t u re s
Features Description
Network Standard
Chipset
Input Voltage
Data Rate
Modulation
Operating Frequency
Operating Channel
IEEE 802.11 b/g/n (final n)
BCM4331
3.3V
802.11b: 1, 2, 5.5, 11Mbps
802.11g: 6, 9, 12, 18, 24, 36, 48, 54Mbps
802.11n-20 MHz: MCS0~MCS23
802.11n-40 MHz: MCS0~MCS23(450Mbps)
802.11b:DBPSK(1Mbps),DQPSK(2Mbps),CCK(5.5Mbps,11Mbps)
802.11g:BPSK(6Mbps,9Mbps),QPSK(12Mbps,18Mbps),
16QAM(24Mbps,36Mbps),64QAM(48Mbps,54Mbps)
802.11n:BPSK(MCS0,MCS8, MCS16),
QPSK(MCS1,MCS2,MCS9,MCS10, MCS17, MCS18),
16QAM(MCS3,MCS4,MCS11,MCS12, MCS19, MCS20),
64QAM(MCS5,MCS6,MCS7,MCS13,MCS14,MCS15, MCS21,
MCS22, MCS23)
802.11b/g/n (2412 ~ 2462 MHz)
1~11 for North America,
Transceiver/Receiver
Mode
3T3R Mode
Chain Ant. Brand Part Number Antenna Type Connector Gain (dBi)
1 1 WNC
81.EZY15.GBR PCB U.FL
3
Remark
TX/RX
2 2 WNC 81.EZY15.GBR PCB U.FL 3 TX/RX
3 3 WNC 81.EZY15.GBR PCB U.FL 3 TX/RX
3 . Be n e fit s
Sm all, self- contained SMT m odu le.
3X3 MI MO function suppor t
High power solut ion support high speed t ransm ittan ce
For product available in the USA/Canada market, only channel 1~11 can be operated.
Selection of other channels is not possible.
Fed e r a l Com m unications Co m m ission St a t e m en t
This device com plies wit h FCC Rules Par t 15. Operation is su bject to the following
i. This device m ay not cau se har m ful interference, and
ii. This device m u st accept any in t er fer en ce r eceiv ed, inclu ding in t er f er en ce t h at m ay cause
undesired operation.
This equipment h as been test ed and found to com ply wit h t h e lim its for a class B digit al dev ice,
pur suant to Par t 15 of t h e Feder al Comm unication s Com m ission ( FCC) r ules. These lim it s are
desig ned t o p rov ide reason ab le p rot ection agai nst harm ful in t erf er en ce in a r esidential inst allation.
This equipment gener ates, u ses, and can r ad iate radio frequ en cy energy and, if not installed and
used in accor dance wit h t he inst ruct ions, m ay cause harm ful in t er fer en ce t o r adio com mun icat ions.
However, t her e is n o guarantee t hat int er fer en ce w ill not occur in a part icular in st allat ion. I f this
equipment does cause harmful int erference to r adio or television r eception , wh ich can be
deter m ined by turn in g t h e equipment off and on , t h e user is encou raged t o t r y to correct the
in t er fer en ce by one or m ore of t he follow in g m easures:
i. Reorient or r elocat e t he receiving an t enna.
ii. I ncrease the separat ion bet w een t he equipm ent an d r eceiv er.
iii. Connect the equipm en t into an outlet on a cir cu it different from that t o w hich the r eceiv er is
connect ed.
Consult the dealer or an exp er ienced r adio/ TV technician for help.
iv.
IMPORTANT NOTE:
This module is intended for OEM integrator. The OEM integrator is still responsible for the FCC
compliance requirement of the end product, which integrates this module.
20cm minimum distance has to be able to be maintained between the antenna and the users for
the host this module is integrated into. Under such configuration, the FCC radiation exposure
limits set forth for an population/uncontrolled environment can be satisfied.
Any changes or modifications not expressly approved by the manufacturer could void the user's
authority to operate this equipment.
USERS MANUAL OF THE END PRODUCT:
In the users manual of the end product, the end user has to be informed to keep at least 20cm
separation with the antenna while this end product is installed and operated. The end user has to
be informed that the FCC radio-frequency exposure guidelines for an uncontrolled environment
can be satisfied. The end user has to also be informed that any changes or modifications not
expressly approved by the manufacturer could void the user's authority to operate this equipment.
If the size of the end product is smaller than 8x10cm, then additional FCC part 15.19 statement is
required to be available in the users manual: This device complies with Part 15 of FCC rules.
Operation is subject to the following two conditions: (1) this device may not cause harmful
interference and (2) this device must accept any interference received, including interference that
may cause undesired operation.
LABEL OF THE END PRODUCT:
The final end product must be labeled in a visible area with the following " Contains TX FCC ID:
PY3UPWL6031H2-2 ". If the size of the end product is larger than 8x10cm, then the following
FCC part 15.19 statement has to also be available on the label: This device complies with Part
15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not
cause harmful interference and (2) this device must accept any interference received, including
interference that may cause undesired operation.
About th is guide
This user guid e cont ains the inform ation your PEGATRON WI FI Module.
Syst em re quirem e n t s
Bef ore installin g t he PEGATRON WI FI m od ule, mak e su re that y our system m eet s the
follow ing requ iremen t s:
Int el® Pentiu m ® 4 or AMD K7 / K8 system
Minim u m 64MB sy st em mem ory
Win dows® XP/ VI STA op er ating syst em
I nst a llin g t h e device drivers
To in st all t he device driver in y ou r com puter:
I nser t the support CD t o t he optical drive and follow the following pr ocedur e.
St ep 1
St ep 2
St ep 3 St ep 4
St ep 5
Loading...