Page 1
Set Up Your Nighthawk 5G
DRAFT
Mobile Hotspot
1 Insert the battery.
SIM card
(preinstalled)
Nighthawk® 5G Mobile Hotspot
LCD Screen
Signal
strength
Number of
connected
devices
Messages
Network
indicator
FOR
POSITION
ONLY
Battery
Wi-Fi network
name and
password
Let’s Get Started
AT&T Eco Rating 2.0 only applies to the NETGEAR
Nighthawk 5G Mobile Hotspot, model M5000. For
limited factors evaluated visit att.com/EcoSpace.
Wireless Emergency Alerts is a registered Trademark
and Service Mark of CTIA.
NETGEAR and Nighthawk are trademarks of
NETGEAR, Inc. 5G is a trademark of 3GPP. 5G not
available everywhere. Contains Lithium ion battery recycle or dispose of properly.
2 Install the back cover.
The battery is partially charged. When you
need to recharge it, connect the USB cable to
the mobile hotspot and then plug into:
• A wall socket, using the wall charger (faster
charge option)
• The USB port on your laptop
Note: The mobile hotspot comes with a preinstalled SIM card.
The SIM must be activated to a data plan with AT&T.
Get to Know Your Nighthawk 5G
Mobile Hotspot
Touch screen
Touch to
navigate
Power
button
Do we need art to show the
USB port location?
Home
Back
Your wireless device displays a network
indicator to let you know which of AT&T’s
wireless networks you are connected to.
5G+
RAN
4G LTE
HSPA+n
Battery charge
Connect to the Internet
Turn on your mobile hotspot
1 Press and hold the Power button for 2
seconds.
Note: The screen displays the hotspot’s Wi-Fi network
name and password.
On your laptop or other wireless device
2 Open your Wi-Fi/network connection
manager.
3 Find your mobile hotspot’s Wi-Fi network
name (ATT-WIFI-XXXX) and connect.
4 Enter your mobile hotspot’s Wi-Fi password.
5 Launch your Internet browser.
Note: The screen goes dark to save power. Press and release
the Power button to wake the screen.
© 2018 AT&T Intellectual Property. All rights reser ved.
AT&T, the AT&T logo and all other AT&T marks
contained herein are trademarks of AT&T Intellectual
Property. All other marks are the proper ty of their
respective owners.
Printed in USA 201-24043-01
USB C port
Page 2
LCD Screens WiFi Settings
DRAFT
Press the Navigation button to scroll
through the screens.
Home screen
Wi-Fi details
ALL IMAGES ARE
FOR POSITION ONLY
WiFi Manager
You can use a browser to view and change the
mobile hotspot settings.
Log In
1 On your Wi-Fi device, type
http://attwifimanager in the browser bar.
2 Log in as administrator.
Default login is attadmin.
Account information
Menu
Change Wi-Fi network name and password
1 On your Wi-Fi device, type
http://attwifimanager in the browser bar.
2 Log in as administrator.
Default login is attadmin.
3 Select Wi-Fi on the menu.
Messages
Device
details
Notification
Hide password
Your WiFi password displays on your mobile
hotspot screen, but you can hide it.
1 On your Wi-Fi device, type
http://attwifimanager in the browser bar.
2 Log in as administrator.
Default login is attadmin.
5 In the Wi-Fi Summary section, under
PASSWORD, clear the Display on homescreen
check box.
The Save button displays near the bottom of
the page.
6 Click Save.
4 In the Main Wi-Fi section, click Edit.
5 Type your new Wi-Fi network name and
password.
6 Change the settings.
The Save button displays near the bottom of
the page.
6 Click Save.
More WiFi Options
You can change more WiFi settings on the
Options page.
1 On your Wi-Fi device, type
http://attwifimanager in the browser bar.
2 Log in as administrator.
Default login is attadmin.
3 Select Wi-Fi on the menu.
4 Select Options.
Page 3
Federal Communication Commission Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC Caution:
Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.
This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
Page 4
Radiation Exposure Statement:
mm
mm
This device meets the government’s requirements for exposure to radio waves.
This device is designed and manufactured not to exceed the emission limits for exposure to
radio frequency (RF) energy set by the Federal Communications Commission of the U.S.
Government.
The exposure standard for wireless device employs a unit of measurement known as the
Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6W/kg. *Tests for SAR
are conducted using standard operating positions accepted by the FCC with the device
transmitting at its highest certified power level in all tested frequency bands.
For body worn operation, this device has been tested and meets the FCC RF exposure
guidelines for use with an accessory that contains no metal and be positioned a minimum of
10cm from the body. Use of other accessories may not ensure compliance with FCC RF
exposure guidelines. If you do not use a body-worn accessory and are not holding the device
at the ear, position the handset a minimum of 10cm from your body when the device is
switched on.
Note: The country code selection is for non-US model only and is not available to all US
model. Per FCC regulation, all WiFi product marketed in US must fixed to US operation
channels only.
Loading...