Netgear orporated 15200306 User Manual

Notification of Compliance

Regulatory Compliance Information

This document includes user requirements for operating NETGEAR products in accordance with national laws
including usage of radio spectrum and operation of radio devices. Failure of the end-user to comply with the
applicable requirements may result in unlawful operation and adverse action against the end-user by the applicable
national regulatory authority.

The NETGEAR product firmware limits operation to only the channels allowed in a particular region or country.
Therefore, all options described in this document may not be available in your version of the product.

This document applies to both Class A and Class B devices:

x Class A devices are intended to be used in a commercial or industrial environment. They are not intended

to be used in a residential home or be available for general public use.

x Class B devices are intended to be used in a residential setting, and may also be used in commercial and

industrial applications. Examples of Class B devices are telephones, personal computers, and residential
data gateways.

x Fuses should only be installed by service personnel.
x NETGEAR recommends the use of 26 AWG or larger gauge phone line cords.

Europe – EU Declaration of Conformity

This section applies to products bearing the CE or CE! mark:

Products bearing the CE or CE! mark comply with the following EU directives:

x EMC Directive 2004/108/EC
x Low Voltage Directive 2006/95/EC
x Ecodesign Directive 2009/125/EC
x RoHS Directive 2011/65/EU

If the product has telecommunications functionality, it also complies with the requirement of the following EU
directive:

x R&TTE Directive 1999/5/EC

Compliance with these directives implies conformity to harmonized European standards that are noted in the EU
Declaration of Conformity. The EU CE Declaration of Conformity may be found at
http://support.netgear.com/app/answers/detail/a_id/11621/.

Caution for installing this equipment outdoors: (Valid in all EU member states, EFTA states, and Switzerland.) Be
aware that outdoor installations require special attention and will only be handled by trained and qualified installation
personnel. No one from the general public is permitted to install NETGEAR wireless products outdoors when
external antennas, power and grounding must be installed for use. Particular attention has to be given allowed
operational frequencies. Contact NETGEAR for instructions on how to contact an installer for outdoor operations if
this product requires the special considerations for outdoor installations. For detailed information concerning
installations in France, the user should contact the national spectrum authority in France (http://www.arcep.fr/ )

x C6300

x FS308v2

x R6220

x WNDR3700v5

x C7000BMX

x FS605v4

x R7500

x WNDR4300v2

x D6000

x FS608v4

x R8000

x WNDR4500v3

x D6010

x GS205v2

x STS7000

x WNR2010

x D3600

x GS208v2

x VEGN2200

x WNR2020

x D3610

x GS305

x VMB3000

x WNR614

x D6200V2

x GS308v2

x VMC3010

x WNR618

x EX2700

x GS605v5

x VMC3030

x EX3700

x GS608v4

x WN370

x EX6100

x HMNC100

x WN1000v4

x EX6150

x JNR1010v2

x WN2500RP

x EX6200

x JR6150

x WN3000RPv2

x EX7000

x JWNR2000v5

x WN3500RP

x FS205v2

x JWNR2010v5

x WNA1000Mv2

x FS208v2

x R6050

x WNDA3100v3

x FS305v2

x R6200v3

x WNDR3400v3

The following paragraphs apply to WN2500RP:

This device is a 2.4GHz and 5GHz wideband transmission system (transceiver), intended for indoor use only in all EU
member states, EFTA states, and Switzerland.

In Italy the end-user should apply for a license at the national spectrum authorities in order to obtain authorization to
use the device for setting up outdoor radio links and/or for applying public access to telecommunications and/or
network services.

This device may not be used for setting up outdoor radio links in France and in some areas the RF output power may
be limited to 10mW EIRP in the frequency range of 2454-2483.5 MHz. For detailed information the end-user should
contact the national spectrum authority in France.

The following paragraph applies to the LG2210:

External antenna requirement: Net gain (antenna + cable) of external antenna is required to be less than 1.14dBi
(minimum gain of internal antenna).

Warning

NETGEAR Class A products that may be utilized in domestic/residential environments may cause radio interference
in which case the user may be required to take adequate measures.

FCC Requirements for Operation in the United States

Information in this section applies to products bearing the FCC mark (or statement):

FCC Information to User

This NETGEAR product does not contain any user serviceable components and is to be used with approved
antennas only. Any product changes or modifications will invalidate all applicable regulatory certifications and
approvals.

The following statement applies to these products:

● D7000

This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or
transmitter except in accordance with FCC multi-transmitter product procedures.

FCC Guidelines for Human Exposure

The NETGEAR product complies with FCC radiation exposure limits set forth for an uncontrolled environment. The
equipment should be installed and operated with minimum distance of 20cm between the radiator and your body.

The following statement applies to this product:

x C6300BD

This product complies with FCC radiation exposure limits set forth for an uncontrolled environment. The device
should be installed and operated with minimum distance of 35cm between the radiator and your body.

The following statement applies to this product:

x C6300XB3

This product complies with FCC radiation exposure limits set forth for an uncontrolled environment. The device
should be installed and operated with minimum distance of 25cm between the radiator and your body.

The following statement applies to this product:

x R8000

This product complies with FCC radiation exposure limits set forth for an uncontrolled environment. The device
should be installed and operated with minimum distance of 30cm between the radiator and your body.

● D7000

FCC Declaration of Conformity

We, NETGEAR, Inc., 350 East Plumeria Drive, San Jose, CA 95134, declare under our sole responsibility that this
product complies with Part 15 Subpart B of FCC CFR47 Rules. Operation is subject to the following two conditions:

x The device may not cause harmful interference, and
x The device must accept any interference received, including interference that may cause undesired

operation.

FCC Radio Frequency Interference Warnings & Instructions

The NETGEAR product has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following methods:

x Reorient or relocate the receiving antenna.
x Increase the separation between the equipment and the receiver.
x Connect the equipment into an electrical outlet on a circuit different from that which the radio receiver is

connected.

x Consult the dealer or an experienced radio/TV technician for help.

FCC RF Radiation Exposure and SAR Statements

The information in this section applies to products that transmit data or communicate wirelessly.

SAR Statement

The information in this section applies to NETGEAR wireless products that are intended to be operated close to
human body.

NETGEAR products that are intended to be operated close to the human body are tested for body-worn Specific
Absorption Rate (SAR) compliance. The SAR limit set by the FCC is 1.6 W/kg.

The FCC has established detailed SAR requirements and NETGEAR products meet these requirements.

NETGEAR products comply with ANSI/IEEE C95.1-1999 and are tested in accordance with the measurement
methods and procedures specified in OET Bulletin 65 Supplement C.

NETGEAR products that are installed in USB ports demonstrate SAR compliance using a typical laptop
computer with a USB port. Other applications, such as handheld computers or similar devices, have not
been verified and might not compliance with related RF exposure rule and such use is prohibited.

RF Exposure Information

NETGEAR products have been evaluated under FCC Bulletin OET 65C (01-01) and found to be compliant to the
requirements as set forth in CFR 47 Sections, 2.1093, and 15.247 (b) (4) addressing RF exposure from radio
frequency devices. NETGEAR products meet the applicable government requirements for exposure to radio
frequency waves. To see the test results reporting the highest SAR level measured for this device, visit
http://www.netgear.com/about/regulatory/declarations-conformity/

Radiation exposure: NETGEAR products comply with radiation exposure limits set forth for an uncontrolled
environment and meet radio frequency (RF) exposure guidelines for wireless routers. NETGEAR products should be
installed and operated keeping the product 20cm or more away from a person’s body. For devices that are battery
powered and may be operated closer than 20cm to you, refer to the NETGEAR website for exposure levels.

NETGEAR USB dongle transmitters are approved for use in typical laptop computers. To comply with FCC RF
exposure requirements, do not use NETGEAR USB dongle transmitters in other devices or certain laptop and tablet
computer configurations where the USB connectors on the host computer are unable to provide or ensure the
necessary operating configurations intended for the device and its users or bystanders to satisfy RF exposure
compliance requirements.

FCC Caution

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s
authority to operate this equipment.

NETGEAR products comply with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1)
NETGEAR products may not cause harmful interference, and (2) NETGEAR products must accept any interference
received, including interference that may cause undesired operation.

For products available in the USA market, only channel 1~11 can be operated. Selection of other channels is not
possible.

The following statement applies to these products:

x D2200D

This equipment complies with Part 68 of the FCC Rules and the requirements adopted by the ACTA.

On the product label of this equipment is a label that contains, among other information, a product identified in the
format US:WXXXXYYYZZZZZ. If requested, this number must be provided to the telephone company.

● D7000

The following statement applies to these products:

x AC779S

x EX6150

x VEGN2200

x WNDR3400v3

x C6300

x EX6200

x VMB3000

x WNA1000Mv2

x C7000BMX

x EX7000

x R8000

x WNDR3700v5

x D2200D

x HMNC100

x VMC3010

x WNDR4300v2

x D6000

x JNR1010v2

x VMC3030

x WNDR4500v3

x D6010

x JR6150

x WAC120

x WNR1000v4

x D3600

x JWNR2000v5

x WN370

x WNR2010

x D3610

x JWNR2010v5

x WN2500RP

x WNR2020

x D6200V2

x R6050

x WN3000RPv2

x WNR614

x EX2700

x R6200v3

x WN3000RPv3

x WNR618

x EX3700

x R6220

x WN3500RP

x EX6100

x R7500

x WNDA3100v3

x A6210

x EX6100

x R8000

x C6300

x EX6150

x STS7000

x C6300XB3

x EX6200

x WN2500RP

x C7000BMX

x EX7000

x WNDR3400v3

x D6000

x HMNC100

x WNDR3700v5

x D6010

x JR6150

x WNDR4300v2

x D3600

x R6050

x WNDR4500v3

x D3610

x R6200v3

x D6200V2

x R6220

x EX3700

x R7500

x A6210

WNDR3400v3

● D7000

The device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or
transmitter except in accordance with FCC multi-transmitter product procedures.

The following statement applies to these products:

● D7000

The device operates in 5.15~5.25GHz frequency range. It is restricted in indoor environment only.

The following statements apply to this product:

x WAC120
x

The device operates in 5.15 ~ 5.25GHz / 5.47 ~5.725GHz frequency range. It is restricted in indoor environment only.
The band from 5600-5650MHz will be disabled by the software during the manufacturing and cannot be changed by
the end user. This device meets all the other requirements specified in Part 15E, Section 15.407 of the FCC Rules.

Non-DFS Warning

NETGEAR non-DFS products do not support operation in the 5600-5650MHz band. The firmware on the device
restricts the operation in this frequency band and does not utilize the channels in this band.

NETGEAR non-DFS products will not permit operations on channels 120–132 for 11a and 11n/a, which overlap the
5600–5650MHz band.

The following statements apply to these products:

x A6210
x HMNC100
x R7500
x R8000

x WNDR3400v3

x A6210

x EX6200

x R7500

x WNDR3400v3

x AC340U

x EX7000

x R8000

x WNDR3700v5

x C7000BMX

x HMNC100

x VMB3000

x WNDR4300v2

x D6000

x JNR1010v2

x VMC3010

x WNDR4500v3

x D6010

x JR6150

x VMC3030

x WNR1000v4

x D3600

x JWNR2000v5

x WAC120

x WNR2010

x D3610

x JWNR2010v5

x WN3000RPv3

x WNR2020

x EX2700

x R6050

x WN370

x WNR614

x EX3700

x R6200v3

x WNA1000Mv2

x WNR618

x EX6150

x R6220

x WNDA3100v3

NETGEAR DFS products do not support operation in the 5600-5650MHz band. The firmware on the device restricts
the operation in this frequency band and does not utilize the channels in this band.

NETGEAR DFS products will not permit operations on channels 120–132 for 11a and 11n/a, which overlap the 5600–
5650MHz band.

Country Code Selection Usage (WLAN devices)

The country code selection is for non-US model only and is not available to all US model. Per FCC regulation, all
WiFi product marketed in US must fixed to US operation channels only.

TV Tuner (on Selected Models)

The information in this section applies to NETGEAR products incorporating a TV tuner.

Note to CATV System Installer: This reminder is provided to call the CATV system installer’s attention to Section 820­93 of the National Electrical Code, which provides guidelines for proper grounding and, in particular, specifies that the
Coaxial cable shield be connected to the grounding system of the building as close to the point of cable entry as
possible.

Canadian Department of Communications Radio Interference
Regulations

The information in this section applies to products bearing the statements:.

“This digital apparatus does not exceed the Class B limits for radio-noise emissions from digital apparatus
as set out in the Radio Interference Regulations of the Canadian Department of Communications.”

“Cet appareil numérique ne dépasse pas les limites de la classe B pour les émissions radio bruit des
appareils numériques, tel qu'énoncé dans le Règlement sur le brouillage radioélectrique du ministère des
Communications du Canada.”

CAN ICES-3 (B)/NMB-3(B)
CAN ICES-3 (A)/NMB-3(A)

Industry Canada

NETGEAR products comply with Industry Canada license-exempt RSS standard(s). Operation is subject to the
following two conditions: (1) NETGEAR products may not cause harmful interference, and (2) NETGEAR products
must accept any interference received, including interference that may cause undesired operation.

Ce dispositif est conforme à la norme CNR d'Industrie Canada applicable aux appareils radio exempts de licence.
Son fonctionnement est sujet aux deux conditions suivantes: (1) le dispositif ne doit pas produire de brouillage