Netgear orporated 14200281 User Manual

Installation

Operation temperature : -20℃ to +60℃

Operation voltage: Input: 44-57Vdc, 0.45A (per each PoE In)
Output: 51Vdc, 15.4W

NETGEAR Outdoor High Power Wireless N
Access Point

WND930

Package Contents

Unpack the box and verify the contents:

• Outdoor High Power Wireless N Access Point

• Wall mounting bracket

• Four bracket screws

• Two pole mount clamps

• Three weatherproof cable glands

Set Up the Access Point

Before mounting the access point in a high location, first set up and test the
unit to verify wireless network connectivity.

Note: The access point has a DHCP client enabled by default. If a DHCP server

exists in your network, the access point obtains an IP address from the DHCP
server. If a DHCP server is not detected in your network aer 30 seconds, the
access point sets its IP address to a static IP address of 192.168.0.100.

¾ To cable your access point:

1. Using an Ethernet cable, connect a power sourcing equipment (PSE) to
a PoE port on the access point.

Note: You must supply either AT power to at least one LAN port or AF power

to two LAN ports to power the access point. You must supply AT power to
both LAN ports to receive PoE power out.

2. If a DHCP server is not connected to your network, configure a
computer with a static IP address of 192.168.0.210 and a subnet mask
of 255.255.255.0.

3. Connect an Ethernet cable from a LAN port on the access point to a
LAN port on the PC.

4. Check the LEDs to verify that the access point is set up correctly.

LED Description

Power LED •O. Power is o.

•Solid green. Power is on.

•Amber, then blinking green. A self-test is running or soware is being

loaded. During startup, the LED is first steady amber, then goes o, and
then blinks green before turning steady green aer about 45 seconds. If
aer one minute the LED remains amber or continues to blink green, it
indicates a system fault.

Activity LED •O. There is no network trac through the access point.

•Blinking green. There is network trac through the access point.

2.4G WLAN
LED

5G WLAN LED •O. The wireless interface is o.

Heater LED •O. Heater is o.

LAN port LEDs •O. No link is detected.

•O. The wireless interface is o.

•Solid green. The wireless interface is on.

•Blinking green. Wireless activity is detected on the 2.4G band.

•Solid green. The wireless interface is on.

•Blinking green. Wireless activity is detected on the 5G band.

•Solid green. Heater is on.

•Solid green. Link is detected.

•Solid amber. 10/100/1000 speed connection is detected.

•Blinking amber. 10/100/1000 speed activity is detected.

¾ To configure your access point for your network:

1. Connect to the access point by opening your browser and entering the
access point’s IP address

If a DHCP server is not installed in your network, the default IP address is

192.168.0.100.

A login window displays.

2. Enter admin for the user name and password for the password, both in
lower case letters.

The access point user interface displays.

3. Select Configuration > System > Basic > General from the menu.

4. Complete the Access Point Name field and select your Country/

Region of operation from the drop-down list.

5. Select Configuration > IP > IP Settings from the menu and configure

the IP settings for your network.

Note: If you use DHCP, reserve an IP address (based on the access point’s

MAC address) on the DHCP server. You can then use that address to log in to
the access point.

6. Select Configuration > Wireless > Basic > Wireless Settings and

configure the wireless settings for your network.
For more information about wireless settings, see the reference manual.

7. Select Configuration > Security > Profile Settings and configure

security profiles for your network.
For more information about security profile settings, see the reference

manual.

Deploy the Access Point

The best location for your access point is elevated such as wall or ceiling
mounted, at the center of your wireless coverage area, and within line of
sight of all mobile devices.

¾ To deploy your access point:

1. Disconnect your access point and position it where you will deploy it.

2. Connect an ethernet cable from your access point to a LAN port on
your router, switch or hub.

3. Connect a power sourcing equipment (PSE) to one of the PoE ports on
the access point.

If your router switch or hub supplies PoE, skip this step.

Note: You must supply either AT power to at least one LAN port or AF power

to two LAN ports to power the access point. You must supply AT power to both
LAN ports to receive PoE power out.

4. Using a wireless device, verify connectivity by using a browser to
connect to the Internet.

August 2014

NETGEAR, Inc.

350 East Plumeria Drive

San Jose, CA 95134, USA

Optional External Antennas

The WND930 supports optional external antennas.

¾ To install optional external 2G or 5G antennas:

1. Attach the 2G or 5G antennas to the corresponding connectors on the
side panels of the access point.

2. Log into the access point and configure it to use the external antennas.

Troubleshooting Tips

This section provides some tips for correcting simple problems that
you might encounter. For more troubleshooting information, see the
troubleshooting chapter in the reference manual.

Problem Cause Possible Solution

No LEDs are
lit on the
access point.

The LAN LED
is o.

The Wireless
LED is o.

You cannot
configure
the access
point from a
browser.

The access
point has no
power.

A hardware
connection
problem exists.

The wireless
connection
does not work.

Multiple
possible
causes.

•Makesurethatapowersourceequipment(PSE)is

connected via Ethernet to at least one PoE port.

•Make sure that the power source equipment (PSE) is
powered on.

•Makesurethatthecableconnectorsaresecurely

plugged into the access point and to the network switch.
Make sure that the network switch is turned on.

•Makesurethepowereddeviceisprovidingsucient

power to the access point.

•Logintotheaccesspointandverifythattheradioor

radios are turned on.

•ContactNETGEARiftheWirelessLEDremainso.

•Make sure that the access point is correctly installed, it

is powered on, and that the LAN LED is lit.

•MakesurethatyourcomputerisusinganIPaddress

in the same range as the access point. The access point
default IP address is 192.168.0.100, and the default
subnet mask is 255.255.255.0.

•Quitthebrowser,clearthecache,deletethecookies,

and launch the browser again.

Problem Cause Possible Solution

You cannot
access the
Internet
or the
LAN from
a wireless
device.

A configuration
problem exists.

•Make sure that the SSID and wireless security settings
of the wireless device are the same as those of the
access point.

•ThewirelessdevicemightnothavethecorrectTCP/IP

settings to communicate with the network. Restart the
wireless device and check that TCP/IP is set up correctly
for that network.

•Theaccesspointdefaultvaluesmightnotwork

with your network. Check the access point default
configuration against the configuration of other devices
in your network. For information about changing the
default values of the access point, see the reference
manual.

Support

Thank you for selecting NETGEAR products. Aer installing your device, locate
the serial number on the label of your product and use it to register your
product at https://my.netgear.com.

You must register your product before you can use NETGEAR telephone
support. NETGEAR recommends registering your product through the NETGEAR
website. For product updates and web support, visit

http://support.netgear.com.

NETGEAR recommends that you use only the ocial NETGEAR support
resources.

For the current EU Declaration of Conformity, visit

http://support.netgear.com/app/answers/detail/a_id/11621/.

For regulatory compliance information, visit

http://www.netgear.com/about/regulatory/.

See the regulatory compliance document before connecting the power supply.

NETGEAR, the NETGEAR logo, and Connect with Innovation are trademarks and/or registered
trademarks of NETGEAR, Inc. and/or its subsidiaries in the United States and/or other countries.
Information is subject to change without notice. © NETGEAR, Inc. All rights reserved.

Federal Communication Commission Interference Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority to operate
this equipment.

This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.

For operation within 5.15 ~ 5.25GHz / 5.47 ~5.725GHz frequency range, it is
restricted to indoor environment. The band from 5600-5650MHz will be
disabled by the software during the manufacturing and cannot be changed by
the end user. This device meets all the other requirements specified in Part
15E, Section 15.407 of the FCC Rules.

Radiation Exposure Statement: