Due to the nature of wireless communications, transmission and reception of data can never be
guaranteed. Data may be delayed, corrupted (i.e., have errors) or be totally lost. Although significant
delays or losses of data are rare when wireless devices such as the NetComm Wireless NHD1W are
used in a normal manner with a well-constructed network, the NetComm Wireless NHD1W should not
be used in situations where failure to transmit or receive data could result in damage of any kind to
the user or any other party, including but not limited to personal injury, death, or loss of property.
NetComm Wireless accepts no responsibility for damages of any kind resulting from delays or errors
in data transmitted or received using the NetComm Wireless NHD1W, or for failure of the NetComm
Wireless NHD1W to transmit or receive such data.
Safety and Product Care of NHD1W
With reference to unpacking, installation, use and maintenance of your electronic device, the following
basic guidelines are recommended:
Do not use or install this product near water to avoid fire or shock hazard. For example, do
not use or install this product near a bathtub, kitchen sink, laundry tub, or near a swimming
pool. Also, do not expose the equipment to rain or damp areas (for example a wet
basement).
Do not connect the power supply cord on elevated surfaces. Allow it to lie freely. There
should be no obstructions in its path and no heavy items should be placed on the cord. In
addition, do not walk on, step on or mistreat the cord.
Warning : Disconnect the power line from the device before servicing.
To safeguard the equipment against overheating, make sure that all openings in the unit
that offer exposure to air are unobstructed.
Safety and Hazards of AirCard Mobile
Hotspot
The AirCard mobile hotspot MUST BE POWERED OFF in all areas that may be susceptible to radio
interference, in particular:
Prohibited areas
Obey all signs and notices and follow all rules and regulations. Power off the mobile hotspot
when instructed to do so or when you suspect that it may cause interference or danger.
In areas where blasting is in progress
Where explosive atmospheres may be present
Areas with a potentially explosive atmosphere are not always clearly marked. Such areas
include gas stations, fuel depots, chemical transfer or storage facilities, areas where
blasting is in progress, areas where the air contains chemicals or particles such as grain,
dust, or metal powders, and any other area where you would normally be advised to turn off
your cellular phone or vehicle engine.
Near medical or life-support equipment
Medical equipment may be susceptible to any form of radio interference. In such areas the
mobile hotspot can transmit signals that could interfere with this equipment.
On board aircraft
Rev 1 Feb. 2012 3
NHD1W User Guide
In addition to Federal Aviation Authority (FAA) requirements, many airline regulations state
that you must suspend wireless operations before boarding an aircraft. The mobile hotspot
is capable of transmitting signals that could interfere with various onboard systems and
controls. Failure to observe this instruction may lead to suspension or denial of cellular
telephone services to the offender, legal action, or both. Some airlines may permit the use
of cellular phones while the aircraft is on the ground and the door is open. The mobile
hotspot may be used normally at this time.
While operating a vehicle
The driver or operator of any vehicle should not use a wireless data device while in control
of a vehicle. Doing so detracts from the driver or operator's ability to control and operate the
vehicle. In some countries, using such communications devices while in control of a vehicle
is an offence.
Caution: Unauthorized modifications or changes not expressly approved by NetComm Wireless, Inc.
could void compliance with regulatory rules, and thereby your authority to use this device.
Limitation of Liability
The information in this manual is subject to change without notice and does not represent a
commitment on the part of NetComm Wireless. NETCOMM WIRELESS AND ITS AFFILIATES
SPECIFICALLY DISCLAIM LIABILITY FOR ANY AND ALL DIRECT, INDIRECT, SPECIAL,
GENERAL, INCIDENTAL, CONSEQUENTIAL, PUNITIVE OR EXEMPLARY DAMAGES INCLUDING,
BUT NOT LIMITED TO, LOSS OF PROFITS OR REVENUE OR ANTICIPATED PROFITS OR
REVENUE ARISING OUT OF THE USE OR INABILITY TO USE ANY NETCOMM WIRELESS
PRODUCT, EVEN IF NETCOMM WIRELESS AND/OR ITS AFFILIATES HAS BEEN ADVISED OF
THE POSSIBILITY OF SUCH DAMAGES OR THEY ARE FORESEEABLE OR FOR CLAIMS BY
ANY THIRD PARTY. Notwithstanding the foregoing, in no event shall NetComm Wireless and/or its
affiliates aggregate liability arising under or in connection with the NetComm Wireless product,
regardless of the number of events, occurrences, or claims giving rise to liability, be in excess of the
price paid by the purchaser for the NetComm Wireless product.
Patents
This product may contain technology developed by or for NetComm Wireless Inc.
The information contained herein is proprietary to NetComm Wireless. No part of this document may
be translated, transcribed, reproduced, in any form, or by any means without prior written consent of
NetComm Wireless.
Trademarks
AirCard® is a registered trademark of Sierra Wireless. Sierra Wireless™, and the Sierra Wireless logo
are trademarks of Sierra Wireless. Other trademarks are the property of their respective owners.
4 2400164
Preface
Sales Desk:
Phone:
1-604-232-1488
Hours:
8:00 AM to 5:00 PM Pacific Time
E-mail:
sales@netcomm.com.au
Post:
NetComm Wireless Limited
PO Box 1200, Lane Cove NSW 2066 Australia
P: +61(0)2 9424 2070 F: +61(0)2 9424 2010
Fax:
1-604-231-1109
Web:
www.netcomm.com.au
Save Our Environment
When this equipment has reached the end of its useful life, it must be taken to a recycling centre and
processed separately from domestic waste.
The cardboard box, the plastic contained in the packaging, and the parts that make up this device can
be recycled in accordance with regionally established regulations. Never dispose of this electronic
equipment along with your household waste. You may be subject to penalties or sanctions under the
law. Instead, ask for disposal instructions from your municipal government.
Please be responsible and protect our environment.
Transport and Handling
When transporting the NHD1W, it is recommended to return the product in the original packaging.
This ensures the product will not be damaged.
Note: Ensure the NHD1W is securely packaged with appropriate padding to prevent damage during courier
transport.
Contact Information
Consult our website for up-to-date product descriptions, documentation, application notes, firmware
upgrades, troubleshooting tips, and press releases: www.netcomm.com.au.
Product Features .................................................................................................................................. 12
LED Indicators ...................................................................................................................................... 13
Small Office / Home Office ................................................................................................................... 26
Power User........................................................................................................................................... 28
Home .................................................................................................................................................... 35
Status ................................................................................................................................................... 35
Internet Settings ................................................................................................................................... 36
LAN Configuration ............................................................................................................................ 36
Rev 1 Feb. 2012 7
NHD1W User Guide
WAN Configuration .......................................................................................................................... 38
Wireless LAN (WLAN) .......................................................................................................................... 40
System Monitor ................................................................................................................................ 50
System ................................................................................................................................................. 51
* This device is only authorized to use with AirCard, FCC ID: N7NAC763S.
This User Guide provides you all the information you need to set up, configure, and
use the NHD1W.
Prerequisites
Before continuing with the installation of your NHD1W, please confirm that you
comply with the minimum system requirements listed below.
AirCard 76xS mobile hotspot activated on a 3G/4G network.
Device with a working Ethernet or wireless (802.11b/g/n) network adapter.
A Web browser such as Internet Explorer, Netscape Navigator, Mozilla
Firefox, Opera, Safari.
Target Users
The NHD1W provides 3 levels of operation modes that allow users access to exactly
the features they need. This User Guide is intended for users who prefer single click,
easy setup, as well as for advanced users who understand telecommunications
terminology and concepts.
Product Overview
3 x 10/100 LAN Ethernet port
1 x 10/100 LAN / WAN Ethernet port for optional alternate Internet
connectivity (ADSL/Cable/Satellite)
802.11n / 300 Mbps wireless1 (backward compatible with 802.11b/g)
Browser-based interface for configuration and management
Wireless security options: WEP, WPA, WPA2
2 x USB ports for attaching USB storage devices to share with connected
clients
Rev 1 Feb. 2012 11
Speeds are dependent on network coverage. See your 3G/4G provider coverage maps for more
details. The total number of Wi-Fi users can also affect data speeds. Maximum wireless signal rate and
coverage values are derived from IEEE Standard 802.11g and 802.11n specifications. Actual wireless
speed and coverage are dependent on network and environmental conditions included but not limited to
volume of network traffic, building materials and construction/layout.
NHD1W User Guide
Package Contents
The NHD1W package consists of:
NHD1W
12V/2A power supply
Two 3G/4G dipole antennas
Ethernet cable
Quick Start Guide
If any of these items are missing or damaged, please contact NetComm Wireless
Support immediately by visiting the NetComm Wireless Support website at:
www.netcomm.com.au/Support.
Product Features
The NHD1W creates a secure Wi-Fi network, providing Internet access for up to 16
users using the 3G/4G network. With quick and easy setup the NHD1W provides a
landline experience without the need for fixed line connections. Simply plug the
NHD1W into a power outlet, and then dock the AirCard mobile hotspot to access a
3G/4G Internet connection within minutes.
The NHD1W incorporates a WLAN 802.11b/g/n access point, four 10/100 Mbps
Ethernet ports, with one able to act as a 10/100 Mbps Ethernet WAN port. Two USB
ports provide connectivity to attached USB storage for connected clients. The
NHD1W features the latest security options, such as WPA and WPA2 data
encryption.
12 2400164
Introduction
Led Indicator
Definition
Power
Power status indicator:
Off = No Power
On = Power
WLAN
Wi-Fi status indicator:
Off = Wi-Fi Off
Solid = Wi-Fi On, no traffic
Flash = Wi-Fi On, data traffic
WWAN
Internet WAN indicator:
Off = No Internet connection
Solid = Internet connected, no traffic
Flash = Internet connected, data traffic
LAN1 / WAN
LAN1/WAN Port connection status indicators:
Off = No cable connection
Solid = Cable connection established
Flash = Data traffic
LAN2
LAN3
LAN4
LAN 2-4 Port connection status indicators:
Off = No cable connection
Solid = Cable connection established
Flash = Data traffic
LED Indicators
The NHD1W is designed to be placed on a desk top. All of the cables exit from the
rear for better organization. The display (visible on the top of the NHD1W) provides
information about network activity and the device status. See below for an
explanation of each of the indicator lights.
Rev 1 Feb. 2012 13
NHD1W User Guide
Interface
Function
3G/4G antenna connectors
Attach external 3G/4G antennas
LAN 1 / WAN
LAN or WAN port for wired Ethernet clients or bridged
devices (for example, ADSL modem)
LAN 2 - 4
LAN Port for wired Ethernet clients (computers, laptops,
etc.)
USB ports
Connect a USB storage device to share content with
connected clients
Power connector
Connects to a DC 12V/2A power adapter
Reset
Hold this button down for over 12 seconds to reset to
factory defaults
Interfaces
The following interfaces are available on the rear panel of the NHD1W:
14 2400164
LAN (Management)
Easy mode
Small Home / Office
mode
Power User mode
Static IP Address
192.168.1.254
192.168.2.1
192.168.2.1
Subnet Mask
255.255.255.0
255.255.255.0
255.255.255.0
Default Gateway
192.168.1.1
192.168.2.1
192.168.2.1
Wireless LAN (Wi-Fi)
SSID (NHD1W)
Displayed on AirCard mobile
hotspot’s LCD screen.
Security Key (NHD1W)
Web interface access (Power User mode only)
Username
admin
Password
admin
Introduction
Default Settings
The following tables list the default settings for the NHD1W. Note that these default
settings may change, once the AirCard mobile hotspot is docked in.
Rev 1 Feb. 2012 15
NHD1W User Guide
16 2400164
2: Get Started
Placement of your NHD1W
Just like your mobile phone, the NHD1W’s location will affect its signal strength to the
3G/4G base station (cell tower). The data speed achievable from the NHD1W is
dependent on this signal strength, which is affected by many environmental factors.
When choosing a location for your NHD1W, keep in mind that the NHD1W needs
adequate signal strength to provide Internet connectivity.
Similarly, the wireless connection between your NHD1W and your Wi-Fi devices is
stronger the closer your devices are to your NHD1W. Your wireless connection and
performance will degrade as the distance between your NHD1W and devices
increases. This may or may not be directly noticeable, and is greatly affected by the
individual installation environment.
If you have concerns about your network’s performance that might be related to
range or obstruction factors, try moving the devices to a position between three to five
meters from the NHD1W to see if distance is the problem.
If you experience difficulties connecting wirelessly between your Wi-Fi devices and
your NHD1W, try the following steps:
In multi-story homes, place the NHD1W on a floor that is as close to the
centre of the home as possible. This may mean placing the NHD1W on an
upper floor.
Avoid placing the NHD1W near a cordless telephone that operates at the
same radio frequency as the NHD1W (2.3 GHz / 4 GHz).
Avoid Obstacles and Interference
Avoid placing your NHD1W near devices that may emit radio “noise,” such as
microwave ovens. Dense objects that can inhibit wireless communication include:
Refrigerators
Washers and dryers
Metal cabinets
Large aquariums
Metallic-based, UV-tinted windows
Note: While some of the items listed above can affect network performance, they will not
prohibit your wireless network from functioning; if you are concerned that your network is
not operating at its maximum effectiveness avoid placing your NHD1W near the devices
listed. Please ensure that your NHD1W’s 3G/4G external antenna is positioned vertically
(toward the ceiling).
Rev 1 Feb. 2012 17
NHD1W User Guide
If your wireless signal seems weak in some spots, make sure that objects such as
those listed above are not blocking the signal’s path (between your devices and the
NHD1W).
Cordless Phones
If the performance of your wireless network is impaired after considering the above
issues, and you have a cordless phone:
Try moving cordless phones away from your NHD1W and your wirelessenabled computers.
Unplug and remove the battery from any cordless phone that operates on the
2.3 GHz / 4 GHz band (check manufacturer’s information). If this fixes the
problem, your phone may be interfering with the NHD1W.
If your phone supports channel selection, change the channel on the phone
to the farthest channel from your wireless network. For example, change the
phone to channel 1 and move your NHD1W to channel 11. See your phone’s
user manual for detailed instructions. If necessary, consider switching to a
900 MHz or 5 GHz cordless phone.
Choose the “Quietest” Channel for your
Wireless Network
In locations where homes or offices are close together, such as apartment buildings
or office complexes, there may be wireless networks nearby that can conflict with
your wireless network. Use the Site Survey capabilities found in the software provided
with your wireless adapter to locate any other wireless networks that are available
(see your wireless adapter’s user manual), and switch your NHD1W and computers
to a channel as far away from other networks as possible. Refer to section Wireless
LAN (WLAN) on page 40.
Experiment with more than one of the available channels, to find the clearest
connection and to avoid interference from neighbouring cordless phones or other
wireless devices.
18 2400164
Get Started
Hardware Installation
1. Attach the supplied antennas to the ports marked “3G/4G ANTENNA”. [Attach in
a clockwise direction, as shown by the red arrow in the photo below.]
2. Turn the metal part to screw in the antenna until it tightens, then hold the metal
part while turning the antenna to a vertical position.
3. Connect the power adapter to the POWER socket on the back of the NHD1W.
Plug the power adapter into the wall socket. The WLAN and WWAN LEDs blink
for approximately 30 seconds while the NHD1W boots up.
4. Follow the instructions provided with your AirCard mobile hotspot to connect to
the Internet. Then dock the AirCard mobile hotspot into the NHD1W.
You are ready to use the NHD1W!
Note: Without the AirCard mobile hotspot, the NHD1W is not functional out of the box.
Rev 1 Feb. 2012 19
NHD1W User Guide
Connecting Wirelessly
1. Ensure Wi-Fi is enabled on your device (for example,
computer/laptop/smartphone/printer/camera).
2. Open the wireless network manager on your device and connect to the network
name shown on the LCD screen of your AirCard mobile hotspot.
3. When prompted for your wireless security settings, enter the Security Key shown
on the LCD screen of the AirCard mobile hotspot.
4. Wait approximately 30 seconds for the connection to establish.
After the setup process is completed, you will be connected to the Internet.
You can connect up to 16 Wi-Fi devices to your NHD1W.
Quick Wi-Fi Setup
Quick Wi-Fi Setup allows users to quickly connect to a Wi-Fi network without the use
of a keyboard. This is sometimes referred to as Wi-Fi Protected Setup (WPS). The
feature is available on many more recent products such as cameras, printers, smart
phones, and laptops.
1. Press the WPS button on your AirCard mobile hotspot docked in the NHD1W
until the WLAN LED on the NHD1W starts flashing.
2. Within 2 minutes press the WPS button on the wireless device you want to
connect or select the WPS-related option in the device’s software.
The NHD1W and your wireless device will communicate and establish the
connection.
Connecting via a Cable
1. Connect the provided Ethernet cable to the port marked LAN1/WAN, LAN 2,
LAN3 or LAN4 at the back of the NHD1W.
2. Connect the other end of the Ethernet cable to your computer.
3. Wait approximately 30 seconds for the connection to establish.
After the setup process is completed, you will be connected to the Internet.
You can connect up to 4 devices via Ethernet cable to the ports marked LAN1/WAN
or LAN 2-4.
20 2400164
Loading...
+ 44 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.