NetComm 3G Wireless Router
N3G007W
User Guide
NetComm
Copyright
The contents of this publication may not be reproduced in any part or as a whole, stored,
transcribed in an information retrieval system, translated into any language, or transmitted in any
form or by any means, mechanical, magnetic, electronic, optical, photocopying, manual, or
otherwise, without the prior written permission.
Trademarks
All products, company, brand names are trademarks or registered trademarks of their respective
companies. They are used for identification purpose only. Specifications are subject to be changed
without prior notice.
FCC Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against radio interference in a commercial environment. This equipment can generate, use and
radiate radio frequency energy and, if not installed and used in accordance with the instructions in
this manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause interference, in which case the user, at his own
expense, will be required to take whatever measures are necessary to correct the interference.
FCC COMPLIANCE STATEMENT
Table of Contents
FCC Interference Statement........................................................................................ 2
System Requirements for Configuration................................................................. 4
1. Introduction............................................................................................................. 5
1.1. Connections............................................................................................ 5
1.1.1. Wireless WAN Mobile Broadband Router (Rear View)......... 5
1.1.2. LEDs– Wireless WAN Mobile Broadband Router (Front View)
............................................................................................................................. 6
1.2. Features............................................................................................................ 7
2. Configuring Wireless WAN Mobile broadband Router.................................... 8
2.1. Installation Considerations .........................................................................8
2.1.1. Installation Instructions- Get Start Networking..........................8
2.1.2. Establish WiFi Connection............................................................. 11
2.2. Using the Configuration Menu.................................................................. 11
2.2.1. Wizard setting.................................................................................... 14
2.2.2. Advanced Setup > Basic Setting.................................................. 22
3. Troubleshooting.......................................................................................................54
4. Technical Specifications ....................................................................................... 58
Package Contents
Importance: Check your product package contents FIRST.
The Wireless WAN Mobile Broadband Router package should contain the items listed
below. If any of the items are missing, please contact your reseller.
items Description Quantity
1 Wireless WAN Mobile
Broadband Router
2 RJ-45 Cable 1
3 Power adapter 5V 3.0A 1
4 Quick Installation Guide 1
5 CD 1
6 Cradle set 1
7
Rubber pad and Sponge
1
1
Caution: Using a power supply with a different voltage rating than the one included with
the Wireless WAN Mobile Broadband Router will cause damage and void the warranty for
this product.
System Requirements for Configuration
• A compatible USB 3G modem card with service
Note: Subject to services and service terms available from your carrier.
• Computers with Windows, Macintosh, or Linux-based operating systems with an installed
Ethernet adapter.
• Internet Explorer version 6.0 or Netscape Navigator version 7.0 and above.
WiFi System Requirements
• An 802.11b, 802.11g Adapter, or 802.11n later
1. Introduction
The Wireless WAN Mobile Broadband Router is a high-performance tool that supports wireless
networking at home, work, or in a public place. The Wireless WAN Mobile Broadband Router
supports uses a Type II PC card or USB 3G modem card, either WCDMA or EVDO and even
HSDPA as well, and supports wireless data transfers up to 54 Mbps, and wired data transfers up
to 100 Mbps.
The Wireless WAN Mobile Broadband Router is compatible with industry security features.
1.1. Connections: 3G modem interface depending on the
difference of models
1.1.1. Wireless WAN Mobile Broadband Router (Rear View)
Antenna
USB port for connecting
with 3G USB modem
Reset Button
Restore to Original
factory defaulted setti n g
Auto MDI/MDIX RJ-45 Ports
Automatically sense the types of WAN
and LAN when connecting to Ethernet
Note:
Contains a reset button to restore the setting back to original factory defaulted setting as if
your convenience of forgetting your applicable setting
Receptor for
Power adapter
y
g
1.1.2. LEDs– 3G Wireless WAN Mobile Broadband Router
3G Status LED
A green light as
power is on and
read
(Front View)
LAN LED
A green light as connected
to local Ethernet and blinks
durin
data is transmission
WiFi LED
A gree n light as
connection on
WLAN available
WAN LED
A green light as
WAN is connected
1.2. Features
z Automatic take over back up with 3G connection as Ethernet WAN failover.
z Implementation within 3 minutes allows the network to go where wires cannot go –
even outside the home or office.
z Fully compatible with the 802.11g standard to provide a wireless data transfer rate of
up to 54Mbps.
z Backwards compatible with the 802.11b standard to provide a wireless data rate of up
to 11Mbps.
z Utilizes
z User-friendly configuration and diagnostic utilities.
z Operates in the 2.4GHz frequency range.
z Advanced Firewall features.
z Supports NAT with VPN pass-through, providing added security.
MAC Filtering
IP Filtering
Port Scheduling
z DHCP server enables all networked computers to automatically receive IP addresses.
z Web-based interface for Managing and Configuring.
z Access Control to manage users on the network.
z Supports special applications that require multiple connections.
z Equipped with 2*10/100 Ethernet ports, for LAN and WAN access, and USB port for
3G network connection.
z Connects multiple computers to a Broadband either WCDMA or EV-DO even
HSDPA modem to share the Internet connection.
Note: The Wireless WAN Mobile Broadband Router is designed to work with either EVDO
or WCDMA (UMTS) even up to 3.5G HSPA PC interface.
Please refer to your service provider for detailed feature information.
OFDM technology (Orthogonal Frequency Division Multiplexing).
2. Configuring Wireless WAN Mobile broadband Router
2.1. Installation Considerations
The Wireless WAN Mobile Broadband Router allows you access your network using a
wireless connection, from virtually anywhere within its operating range. Keep in mind
however, that the number, thickness, and location of walls, ceilings, or other objects that the
wireless signals must pass through, may limit this range.
Typical ranges vary depending on the types of materials used, and background RF (radio
frequency) noise in your home or business.
To maximize your wireless range, please follow these guidelines:
1. Keep the number of walls and ceilings between the Wireless WAN Mobile Broadband
Router and other network devices to a minimum. Each wall or ceiling can reduce the
Wireless WAN Mobile Broadband Router’s range from 3-90 feet (1-30 meters).
Note: The same considerations apply to your broadband EVDO connection.
2. Keep your product aware from electrical devices (such as microwaves, air conditioners,
and televisions) that emit large quantities of RFI (Radio Frequency Interference).
2.1.1. Installation Instructions- Get Start Networking
Connect the Wireless Router to Your Network
Note: DO NOT connect Wireless WAN Mobile Broadband Router to power before
performing the installation steps below.
1. Attach the antenna.---picture 2.1
Picture 2.1
a. Remove the antenna from its plastic wrapper.
b. Screw the antenna in a clockwise direction to the back panel of the unit.
c. Once secured, position the antenna upward at its connecting joint. This will
ensure optimal reception.
2. Plug in USB modem with service to the Wireless WAN Mobile Broadband Router
---see Picture 2.2
Picture 2.2
Note: The Wireless WAN Mobile Broadband Router is designed to work with
either UMTS or EV-DO and even HSDPA 3G card that can be used as a modem
(support tethered data). Please refer to your service provider for detailed feature
information.
3. Insert the Ethernet patch cable into LAN Port on the back panel of the Wireless
WAN Mobile Broadband Router, and an available Ethernet port on the network
adapter in the computer you will use to configur e the unit.-see Picture 2.3
Picture 2.3
Note: The Wireless WAN Mobile Broadband Router LAN Port is
“Auto-MDI/MDIX.” This provides patch Ethe rnet cable LAN Port acc ess.
4. Connect the power adapter to the receptor on the back panel of your Wireless WAN
Loading...