NetComm Wireless 3G25WR User Manual

Overview

The NetComm 3G25W-R integrates a Wireless LAN and 3G WAN into one unit. Connection to the Internet is achieved through either a 3G service or via a fixed line xDSL/Cable/Satellite connection to the 3G25W-R’s WAN port, providing you with the flexibility to choose how you access the Internet. The 3G25W-R’s automatic failover ensures you are always connected by activating the 3G connection should the xDSL/Cable/Satellite connection drop out.

Users are able to share a single 3G connection via both a wired and wireless connection to the 3G25W-R. With a built in 802.11n wireless access point, this router provides wireless speeds of up to 150Mbps, 150% faster than 11g technology¹. On top of this, the 3G25W-R has four LAN ports for wired connections to multiple devices. Rather than being restricted to certain USB modems, the 3G25W-R allows the user to simply insert an active SIM and utilise 3G Mobile Broadband for internet connectivity.

The 3G25W-R includes advanced security features such as VPN pass-through, a full complement of wireless security options and a built in firewall.

1 Maximum wireless signal rate and coverage values are derived from IEEE Standard 802.11g and

802.11n Draft 2.0 specifications. Actual wireless speed and coverage are dependent on network and environmental conditions included but not limited to volume of network traffic, building materials and construction/layout.

3G25W-R Features:

 Powerful wireless router with support for 3G Mobile Broadband  Creates instant Wireless hotspots to share the Internet

connection of a 3G USB modem or DSL/Cable modem

 Supports Wireless N standard with data speeds up to

150Mbps¹

 One WAN port for alternate wired Internet connection

(DSL/Cable/Satellite via Ethernet)

 Four LAN ports to connect wired devices like PCs or gaming

consoles

 Ensures connectivity and business continuity with auto Internet

failover from WAN port to 3G Mobile Broadband

 Easy WiFi Protected Setup (WPS) by the single touch of a

button to establish a secure wireless connection

 Full Wireless security - WEP, WPA, WPA2  Browser based interface for configuration and management:

OS independent and easy to use

Package Contents

Your 3G25W-R Wireless Router with voice Package contains the following items:

 3G25W-R Wireless Router  Quick Installation Guide  User Guide on CD  Power Supply Unit  Ethernet Cable

If any of the above items are damaged or missing, please contact your dealer immediately.

Minimum System Requirements

Before continuing with the installation of your 3G25W-R Wireless Router, please confirm that you comply with the minimum system requirements.

 Active SIM card for 3G Broadband access if you want to use a

3G Broadband service.

Note: Subject to terms and conditions from your 3G Broadband Internet Service.

 Computer with Windows, Macintosh, or Linux-based operating

systems with a working Ethernet adapter with TCP/IP Protocol installed.

 Internet Explorer version 6.0 or Netscape Navigator version 7.0

and above.

Wireless Computer System Requirements

 Computer with a working 802.11b, 802.11g, 802.11n wireless

adapter

LED indicators:

(PICTURES)

Status Green in flash Device status is working. 3G Signal Strength LED

LED color Description

Red in flash

Amber in flash Connecting. Red

Red in quick flash Roaming alert, and 3G signal is

Amber

Disconnected. No SIM card / signal or unverified

PIN code

Connected. Signal strength in level one

(weak)

weak

Connected. Signal strength in level two or

three (middle)

Amber in quick flash Roaming alert, and 3G signal is

middle

Green Connected.

Signal strength in level four or five (strong)

Green in quick flash Roaming alert, and 3G signal is

strong

2G/2.5G LED

3G/3.5G LED

USB / 3G LED Green Connected with 3G dongle via

WiFi LED

Green EDGE or GPRS connection is

established

Green in flash Data packet transferred via

2G/2.5G

Green UMTS/HSDPA/HSUPA

connection is established

Green in flash Data packet transferred via

3G/3.5G

USB port Green RJ45 cable is plugged WAN LED Green in flash Data access Green RJ45 cable is plugged LAN LED Green in flash Data access Green WLAN is on Green in flash Device is in WPS PBC mode Green in fast flash Device is in WPS PBC mode

Restoring Factory Defaults

This feature will reset the Router to its factory default configuration. Occasions may present themselves where you need to restore the factory default settings on your router. Typical situations are:

 You have lost your password and unable to login to the router;

 You have purchased the router from someone else and need to reconfigure the

device.

 You are asked to perform a factory reset by a member of the excellent NetComm

Support Staff.

 In order to restore your ro uter to its factory default settings, please follow these steps:  Ensure that the router is powered on (for at least 20 seconds).  Use a paper clip or a pencil tip to depress the reset button for ten seconds and

release. At this point, the reset is in progress. Do not power off the unit at this point.

 After the router reboots, the default settings are now restored. This entire process

takes several minutes to complete.

 Once you have reset the router to its default settings you will be able to access the

device’s web configuration using http://192.168.1.1 with password “admin”.

Default Settings

LAN (Management)

Static IP Address: 192.168.1.x Subnet Mask: 255.255.255.0 Default Gateway: 192.168.1.1

WAN (Internet)

WAN mode: DHCP

Wireless

SSID:

(refer to the wireless security card insert)

Security: WPA2-PSK WEP Key:

(refer to the wireless security card insert)

Modem Access

Password: admin

Connecting your 3G25W-R Wireless Router

Step 1: Attach the antenna.

1. Remove the antenna from its plastic wrapper.

2. Screw the antenna in a clockwise direction to the back panel of the unit.

3. Once secured, position the antenna upward at its connecting joint. This will ensure optimal reception.

4. And pull out the “USIM/SIM & PWR” labelled tag.

5. Ensure the Power Switch is off.

DO NOT connect the 3G25W-R to power before performing the installation steps below.

Step 2: Insert a SIM/USIM into the 3G25W-R. Step 3: Insert the Ethernet cable into the LAN Port: Insert the Ethernet cable into LAN port on the back panel of the 3G25W-R, and an available

Ethernet port on the network adapter on the computer you will use to configure the 3G25 W-R. Step 4: Power on the 3G25W-R:

1. Connect the power adapter to the receptor on the back panel of your 3G25W-R.

2. Then plug the other end of the power adapter into a wall outlet or power strip.

3. Turn on the Power Switch. Step 5: Complete the setup.

1. All LEDs will flash to indicate power has been applied.

2. The LEDs will flash ON and OFF as the 3G25W-R performs its startup initialisation and Internet connection processes. This will take a few minutes.

3. When complete, the Status LED will flash.

SettingupyourPC

Having physically connected your 3G25W-R, the next step is to configure the router to establish a broadband connection. Depending on your computers current settings you may first need to reconfigure the TCP/IP (Network Settings) to access your Wireless Router. Follow the instructions for your operating system.

ForWindows98SE/ME/2000/XP

1. Click on “Start” -> “Control Panel” (in Classic View). In the Control Panel; double click on

“Network Connections” to continue.

Single RIGHT click on “Local Area connection”, then click “Properties”.

3. Double click on “Internet Protocol (TCP/IP)”.

4. Check “Obtain an IP address automatically” and “Obtain DNS server address automatically”

then click on “OK” to continue

5. Click “Show icon in notification area when connected” (see screen image in 3. above) then click on “OK” to complete the setup procedures.

ForWindowsVista32/64

1. Click on “Start” -> “Control Panel” -> “Network and Sharing Center”.

2. In the Manage network connections, click on “Manage network connections” to continue.

3. Single RIGHT click on “Local Area connection”, then click “Properties”.

4. The screen will display the information “User Account Control” and click “Continue” to continue.

5. Double click on “Internet Protocol Version 4 (TCP/IPv4)”.

6. Check “Obtain an IP address automatically” and “Obtain DNS server address automatically”

then click on “OK” to continue.

ForWindows732/64

1. Click on “Start” -> “Control Panel” (in Category View) -> “View network status and tasks”.

2. In the Control Panel Home, click on “Change adapter settings” to continue.

3. Single RIGHT click on “Local Area Connection”, then click “Properties”.

4. Double click on “Internet Protocol Version 4 (TCP/IPv4)”.

5. Check “Obtain an IP address automatically” and “Obtain DNS server address automatically”

then click on “OK” to continue.

ForMacOSX10.6

1. Click the Apple icon and choose System Preferences.

2. Click on Network icon.

3. Set Location to Automatic and Show to Built-In Ethernet.

4. In the Configure option, choose Using DHCP.

5. Click on Apply Now.

Web Configuration Wizard

Having physically connected your 3G25W-R, the next step is to establish the broadband connection to the internet. Please follow the steps below to configure your 3G25W-R Wireless router via the web configuration wizard utility.

1. Open your web browser (e.g. Internet Explorer/Firefox/Safari) and navigate to http://192.168.1.1/

2. At the login screen, type in “admin” (without quotes) in the System Password field. Then click on Login.

Notes: admin is the default login password for the unit.

3. Click on Wizard and then on Enter.

4. This page shows you the steps needed to configure your 3G25W-R unit. Click Next to continue.

5. After choosing 3G, you need to enter the information below, this will have been provided to you by your 3G broadband service provider. Click Apply Setting onc e you finished.

6. . After several minutes the 3G25W-R will save all the settings and the wizard is complete. Click Finish to go back to the Status page and the unit will now use the new settings.

7. If everything is configured properly, the System Status page will show that your 3G service is online and the WAN IP address that has been assigned.

Advanced Setup

To access the Advanced Setup option of your 3G25W-R, you need to access the 3G25W-R’s web configuration outlined in the Web configuration section and click on the Advanced Setup menu at the top of the page.

For first time installation, you will be presented with the following page. Choose Advanced to access the Advanced Setup page.

After that, click on any of the top menu to access the respective setting pages.

BasicSetting

The Basic Setting page allows you to configure a number of basic settings on the unit. This section deals with these features. Click on any of the menu on the left to configure the respective setting page.



BasicSetting>NetworkSetup

This Page allows you to change the LAN (Local Area Network) settings on your 3G25W-R Wireless router and the WAN (Wide Area Network) connection.

1. LAN IP Address: the local IP address of the 3G25W-R. The computers on your network must use this IP address as their Default Gateway. You can change it if necessary.

2. Subnet Mask: Enter 255.255.255.0 in the subnet field.

3. WAN Interface: Select Ethernet WAN or Wireless WAN.

4. WAN Type: WAN connection type. Click the WAN Type pulldown menu to choose the appropriate connection type from the following options:

- Static IP Address

 Enter the WAN IP Address, Subnet Mask, Gateway, Primary and Secondary DNS as supplied

by your ISP.

- Dynamic IP Address

 Activate WWAN for Auto-Failover: The WAN type will be change to wireless-WAN automatically

if the wired-WAN connection disconnects.

 Host Name: Set the hostname for your connection (optional - Refer to your ISP for more

information).

 ISP register MAC address: You can change the WAN port MAC address if needed to clone

your 3G modem (optional - Refer to your ISP for more information).

 Connection Control: There are 3 modes to select :-

Connect-on-demand: The 3G25W-R will connect to the internet when a client sends outgoing packets.

Auto Reconnect (Always-on): The 3G25W-R will automatically reconnect to the internet until the connection is manually disconnected.

Manually: The 3G25W-R will not connect to the internet until someone clicks the connect button in the Status-page.

 NAT disable: This option disables "Network Address Translation" for this connection type.

- PPP over Ethernet

 Activate WWAN for Auto-Failover: The WAN type will be change to wireless-WAN automatically

if the wired-WAN connection disconnects.

 PPPoE Account and Password: The account and password your ISP assigned to you. For

security, this field appears blank. If you don't want to change the password, leave it empty.

 Primary DNS/Secondary DNS: This feature allows you to manually assign a Primary/Secondary

DNS Server (Refer to your ISP for more information).

 Connection Control: There are 3 modes to select :-

Connect-on-demand: The 3G25W-R will connect to the internet when a client sends outgoing packets.

Auto Reconnect (Always-on): The 3G25W-R will automatically reconnect to the internet until the connection is manually disconnected.

Manually: The 3G25W-R will not connect to the internet until someone clicks the connect button in the Status-page.

 Maximum Idle Time: The amount of inactivity on the internet connection before it is

disconnected. Set it to zero or enable “Auto-reconnect＂ to disable this feature.

 PPPoE Service Name: Enter the service name if your ISP requires it (optional).

 Assigned IP address: Enter the IP address assigned to your service. This is usually left blank.

 Maximum Transmission Unit (MTU): The default MTU value is 0(auto). It is set automatically

when you connect.

 NAT disable: This option disables "Network Address Translation" for this connection type.

- PPTP

Please verify your connection type and select the appropriate IP Mode - Static IP Address or Dynamic IP Address.

If you are using a Static address enter the information provided to you by your service provider.

 Activate WWAN for Auto-Failover: The WAN type will be change to wireless-WAN automatically

if the wired-WAN connection disconnects.

 My IP Address, My Subnet Mask and WAN Gateway IP: the private IP address, subnet mask

and Gateway IP your service provider assigned to you.

 Server IP Address/Name: the IP address or URL of the PPTP server.

 PPTP Account and Password: The account and password your PPTP provider assigned to you.

If you don't want to change the password, keep it empty.

 Connection ID: Enter your connection ID if required.

 Maximum Idle Time: The amount of inactivity on the internet connection before it is

disconnected. Set it to zero or enable “Auto-reconnect＂ to disable this feature.

 Connection Control: There are 3 modes to select :-

Connect-on-demand: The 3G25W-R will connect to the internet when a client sends outgoing packets.

Auto Reconnect (Always-on): The 3G25W-R will automatically reconnect to the internet until the connection is manually disconnected.

Manually: The 3G25W-R will not connect to the internet until someone clicks the connect button in the Status-page.

 Maximum Transmission Unit (MTU): The default MTU value is 0(auto). It is set automatically

when you connect.

- L2TP

Please verify your connection type and select the appropriate IP Mode - Static IP Address or Dynamic IP Address.

If you are using a Static address enter the information provided to your by your service provider.

 Activate WWAN for Auto-Failover: The WAN type will be change to wireless-WAN automatically

if the wired-WAN connection disconnects.

 IP Address, Subnet Mask and WAN Gateway IP: the private IP address, subnet mask and

Gateway IP your service provider assigned to you.

 Server IP Address/Name: The IP address or URL of the L2TP server.

 L2TP Account and Password: The account and password your L2TP provider assigned to you.

If you don't want to change the password, keep it empty.

 Maximum Idle Time: The amount of inactivity on the internet connection before it is

disconnected. Set it to zero or enable “Auto-reconnect＂ to disable this feature.

 Connection Control: There are 3 modes to select :-

Connect-on-demand: The 3G25W-R will connect to the internet when a client sends outgoing packets.

Auto Reconnect (Always-on): The 3G25W-R will automatically reconnect to the internet until the connection is manually disconnected.

Manually: The 3G25W-R will not connect to the internet until someone clicks the connect button in the Status-page.

 Maximum Transmission Unit (MTU): The default MTU value is 0(auto). It is set automatically

when you connect.

- 3G

Please note: The WAN fields may not be necessary for your 3G connection. The information on this

page will only be used when required by your 3G service provider.

Please contact your 3G provider to obtain this information if needed.

 Dial-Up Profile: Select auto or manual to continue.

 Country: select your country.

 Telecom: select your 3G provider.

 3G Network: select the 3G Network type.

 APN: Enter the APN for your 3G service.

 Pin Code: Enter the Pin Code for your SIM card.

 Dial-Number: This number required to connect to your 3G service.

 Account: The username provided by your 3G service provider to enable access to your 3G

service.

 Password: The password provided by your 3G service provider to enable access to your 3G

service.

 Authentication: Choose the appropriate authentication type for your 3G service.

 Primary DNS: Manually assign a Primary DNS Server.

 Secondary DNS: Manually assign a Secondary DNS Server.

 Connection Control: There are 3 modes to select :-

Connect-on-demand: The 3G25W-R will connect to the internet when a client sends outgoing packets.

Auto Reconnect (Always-on): The 3G25W-R will automatically reconnect to the internet until the connection is manually disconnected.

Manually: The 3G25W-R will not connect to the internet until someone clicks the connect button in the Status-page.

 Keep Alive: Enables the 3G25W-R to maintain your internet connection.



BasicSetting>DHCPServer

1. DHCP Server: Enable or disable the DHCP server.

2. Lease Time: Length of the DHCP lease time

3. IP Pool Starting/Ending Address: Whenever there is a request, the DHCP server will automatically allocate an unused IP address from the IP address pool to the requesting computer. You must specify the starting / ending address of the IP address pool

4. Domain Name: Optional, this information will be passed to the client Click “Save” to save these settings or Undo to cancel. You can also check the DHCP client list by pressing the Client List button. Fixed Mapping button allows you to map a specific IP address to a specific MAC address. Press “More…” for more options,

DHCPClientsList

The list of DHCP clients is shown here.

DHCPFixedMapping

The DHCP Server will reserve a specific IP for a specific MAC address, shown below.

BasicSetting>Wireless

This page allows you to configure the wireless network features of the router.

The Wireless settings page allows you to set the wireless configuration items.

1. Network ID (SSID): Network ID is used for identifying the Wireless LAN (WLAN). Client stations can roam freely over this product and other Access Points that have the same Network ID. (The factory default setting is “3G25W-R”)

2. SSID Broadcast: The router will broadcast the SSID so that wireless clients can find the wireless network.

3. Channel: The wireless radio channel in use by your network.

4. Wireless Mode: Choose B/G Mixed, B only, G only, and N only, G/N Mixed or B/G/N mixed. The factory default setting is B/G/N mixed.

5. Authentication mode: You may select from seven kinds of authentication to secure your wireless network: Open, Shared, Auto, WPA-PSK, WPA2-PSK, and WPA-PSK/WPA2-PSK.

WPA-PSK/WPA2-PSK - A newer type of security is WPA-PSK-TKIP and WPA-PSK2-ADE. This type of security gives a more secure network compare to WEP. Use TKIP Encryption Type for WPA-PSK and AES for WPA2-PSK. Please enter the key in the Passphrase field. The key needs to be more then 8 characters and less then 63 characters and it can be any combination of letters and numbers.

The factory default setting is: a1b2c3d4e5 Please note that the configuration for WPA-PSK and WPA2-PSK is identical

Notes: After configuring wireless security, you also need to configure your wireless adapter to use the same security settings before you can connect wirelessly. Not all wireless adapter supports WPA-PSK/WPA2PSK/WPA/WPA2 security, please refer to your wireless adapter user guide for more details. It is strongly recommended to set up wireless security such as WPA-PSK (when the wireless client supports WPA) in order to secure your network.

Click “Save” to save these settings or click “Undo” to cancel.

WDS(WirelessDistributionSystem)

WDS operation as defined by the IEEE802.11 standard has been made available. Using WDS it is possible to wirelessly connect Access Points, and in doing so extend a wired infrastructure to locations where cabling is not possible or inefficient to implement.

WPSSetup

WPS is a Wi-Fi Protection Setup which is similar to WCN-NET and offers safe and easy way to connect Wirelessly.

WirelessClientList

The list of wireless clients is shown here.

BasicSetting>ChangePassword

On this page you can change the 3G25W-R web configuration password. Please type in your old password (the factory default password is admin) and then type in the new password. Type the same new password in the

Reconfirm field.

Note: if you change the password, please make sure that you use the new password the next time you log into the

web configuration.

Click “Save” to save the settings or “Undo” to cancel.

ForwardingRules

The Forwarding Rules page allows you to configure the port f the menu

items on

Forwarding rules are a necessary incoming Because of this, NAT this also creates a connectivity problem when you want to make LAN resources availa you may

There are three ways to Forwarding (in page).

traffic from the Internet to the LAN unless a specific port mapping exists in the NAT

want to do to play

the left to access the respective settings pa

fea

provides a level of protection for

network games or host network a

work around NAT

the

Virtual Ser

ver page), Port T

ture as by

default NAT

and to ena

riggering (in

orwarding management on the router. Click on any of

ge.

(Network Address T

computers that

ble certain LAN resources a

the

are connected to your LAN. However,

pplications.

Special AP pa

vaila

ge) and DMZ Host (in

ranslation) will automa

translation table.

ble to Internet clients, which

ble from the Internet; Port

the

Miscellaneous

tically

block

ForwardingRules>

A virtual ser specified Access

For example, if you have an

80) at f

ollowing virtual ser

Ser

21 80 1723

Note: At any given time, only

Click “Sa

ver is defined as a Ser

by the Server IP. Virtual Servers can also work with Scheduling Rules, and g

control. For detail instructions on scheduling rules, please refer to Advanced Setting > Scheduling.

192.168.1.20, and a VPN ser

vice.Port

ver mapping table:

one IP address can bind to a particular Ser

ve” to save

the settings or “Undo” to cancel.

Virtual

Ser

ver



vice Port, and all requests to this port will be redirected to the computer

ive you more flexibility on

FTP ser

ver (default port is port 21) at

ver (default port is port 1723) at

Ser

ver.

192.168.1.10

192.168.1.20

192.168.1.60

192.168.1.10, a Web

192.168.1.60, then you need to specify the

Enable

T T T

vice Port.

icked icked icked

ser

ver (default port is port

ForwardingRules>SpecialAP

Some a

pplications like On-line games, Video conferencing and Internet telephony to the internet. Because of that, The Special Applica the a

pplication work, try to

Miscellaneous section for assistanc e do in g this. The fields are explained as f

Trig

Incoming Ports: when the trig numbers

The 3G32VW also provides predefined settings for

your a

select After that

Click “Sa

ve” to save

tions fea

ger: the outbound port number that

will be allowed to pass through the firewall.

pplication from the Popular a

the predefined settings will be added to the list.

the settings or “Undo” to cancel.

these a

ture allows some of these a

set up that

ollow:



pplications cannot work with a pure NAT

computer as the DMZ host instead. Please refer to Forwarding Rules >

ger packet is detected, the inbound packets sent to the specified port

pplication list, select an unused ID from the list and then click Copy

pplications to work with this router. If

will be trig

gered by

some popular a

require multiple connections

router such as the 3G25W-R

the a

pplica

tion..

pplica

tions. To

use the predefined settings,

this fails to make

to.

Forw

ardingRules>

Miscellaneous



DMZ (Demilitarized Zone) Host is a computer without the protection of firewall. It allows that to be exposed to unrestricted 2-way conferencing, Internet telephony

ena

ble DMZ, enter the IP address of the PC and tick on Ena

Note: This fea

UPnP Setting, The device also supports this function. If the OS supports this function enable it. Click “Save” to save the settings or “Undo” to cancel.

ture should be used only

communication to the internet. It is mostly

and other special a

when necessary.

pplications.

ble.

used for

Internet games, Video

particular computer

3GT2WN

SecuritySetting

The Security Setting page allows you to configure the security management on the router such as Packet filters and items

the left to access the respective setting pa

ge.

MAC Control. Click on any of

the menu

SecuritySetting>PacketFilters

The Packet Filter ena which a

pplies to all outbound packets and Inbound Packet Filter which only a

ena

ble an Outbound Filter,

bles you to control what

please make sure to tick the Ena

packets are allowed to pass through the router.



pplies to packets that are

ble tick box on the top of the pa

There are two types of packet filter,

destined for a Virtual Server or DMZ host only.

ge.

There are two type of filtering policies:

Outbound Packet Filter

Allow all data

Deny

For each direction, you can specify up to 48 rules. For

•

Source IP address

•

Source port

•

Destina

•

Destina

•

Protocol: TCP or UDP or both.

•

Use Schedule Rule#

For source or destination IP address, you can define a single IP address (192.168.1.1) or a range of IP addresses (192.168.1.100-192.168.1.200). Empty fields imply

For source or destination port, you can also define a single port (80) or a range of ports (1000-1999). Use the prefix “T” or “U” to specify protocol e.g. T80, U53, U2000-2999. No prefix indicates both TCP and UDP are defined. An empty

The Packet Filter also works with Scheduling Rules, and g please refer to

Click “Sa

ve” to save

traffic to pass except those

all data

traffic to pass except those

tion IP address tion port

the

Advanced Setting > Scheduling section.

the settings or “Undo” to cancel.

field

that match the specified rules.

implies all ports.

each rule you

ives you more flexibility on Access control. For detailed instructions regarding scheduling rules,

will

all IP addresses.

need to define the f

ollowing:

Inbound

Filter:



either the

TCP or UDP

access the Inbound Packet Filter pa

the one for

the Outbound Filter.

ge, click on the “Inbound Filter” button on the bottom of the Outbound Filter pa

ge. All the settings on this page are similar to

Click “Sa

ve” to save

the settings or “Undo” to cancel.

SecuritySetting>DomainFilters

Domain Filters ena

ena

ble the Domain Filter please make sure to tick the Ena

Log DNS Query. Please tick the Ena URLs.

ble you to prevent users from accessing specific domain addresses.

ble tick box if you want to log when someone accesses specific



ble tick box on the top of the pa

ge.

Privilege Host/Netmask. To To

set a Domain Filter,

•

Domain Suffix: Please type the suffix of the URL that

•

Action: The router action that on Log to log this access.

•

Ena

ble. T

ick to ena

Click “Sa

ve” to save

the settings or “Undo” to cancel.

set a group of computer that

you need to specify the f

you want when someone is accessing a URL that

ble the rule.

has privilege to access the internet without any

ollowing:

needs to be restricted. For example, “.com”, “xxx.

restriction.

met the domain suffix. Tick on Drop to block the access and/or tick

com”.

SecuritySetting>URLBloc

URL Blocking will block LAN computers from connecting to a pre-defined website. Domain Filter and URL Blocking is that

URL Blocking only

ena

ble URL Blocking please make sure to tick on Ena

specify the f

•

URL. If any “sex” to block all websites if their URLs contain the pre-

•

Ena

Click “Sa

ve” to save

requires you to input a ke

ollowing:

part of the W

ble. T

ick to ena

ble the rule.

the settings or “Undo” to cancel.

king



Domain Filter require users to input a suffix (e.g. xxx.com, yyy

yword.

ble tick box on the top of the pa

ebsite’s

URL matches the pre-defined word then the connection will be blocked.

defined word “sex”.

The major dif

ference between

.net) while

ge. To set a URL Blocking rule, you need to

For example, you can use pre-defined word

SecuritySetting>MACControl

MAC Control allows you to assign dif a specific MAC address.

ena

ble MAC Address Control please make sure to tick the Ena

•

Connection control. Check Connection Control to control which clients (wired and wireless) can connect to the unit. If a client is denied to connect to this device, it means the client can not access to the Internet either.

clients with MAC addresses that connect to this device.

•

Associa If a client is denied to associate

the clients with MAC addresses that

tion control. Check Associa

ferent access rights for

are not in the list to

tion Control to control which wireless client can associate

with the unit, it means the client can not send or receive any data via this

are not in the list to



dif

ferent users and to assign a specific IP address to

ble tick box on the top of the pa

associate to

the wireless LAN

ge. Two types of control are availa

with the unit.

ble:

Choose allow or deny to

device. Choose allow or deny to

allow or deny

Click

Click “Sa

the “

ve” to save

Next Pa

ge” or

the “

Previous Pa

the settings or “Undo” to cancel.

ge” buttons to see the entire list.

SecuritySetting>

This page allows you to change various miscellaneous security settings on the un

Miscellaneous



it.

Administrator Time-out

The period of time with no activity in the web configuration page to logout automatically, you may set it to zero to disable this feature.

Remote Administrator Host/Port

In general, only Intranet users can browse the built-in web pages to perform administration task. This feature enables you to perform administration tasks from a remote host. If this feature is enabled, only the specified IP address can perform remote administration. If the specified IP address is 0.0.0.0, any host can connect to the router to perform administration tasks. You can use subnet mask bit (/nn) notation to specify a group of trusted IP addresses for example, "10.1.2.0/24".

NOTE: When Remote Administration is enabled, the web server port will be shifted to 80. You can also change the web server port.

Discard PING from WAN side

When this feature is enabled, your router will not respond to ping requests from remote hosts.

DoS Attack Detection

When this feature is enabled, the router will detect and log where the DoS attack comes from on the Internet. Currently, the router can detect the following DoS attack types: SYN Attack, WinNuke, Port Scan, Ping of Death and Land Attack, as well as others.

Click “Sa

ve” to save

the settings or “Undo” to cancel.

AdvancedSetting

The Advanced Setting page allows you to configure the advanced settings on the router such as DNS and SNM

P options. Click on any of the menu items on the left to configure the access the respective setting page.

the System log, Dynamic

Adv

ancedSetting>SystemLog

This enables you to set up the system log features of the router. You can also choose to export the system log via email (SMTP) or send it to a remote syslog server (UDP).

IP Address for Syslogd

Host IP of destination where sys log will be sent to. Check Enable to enable this function.

Setting of Email alert

Check if you want to enable Email alert (send syslog via email). Check Enable to enable this function.

SMTP Server IP and Port

Input the SMTP server IP and port, which are connected with ':'. If you do not specify port number, the default value is 25.For example, "mail.your_url.com" or "192.168.1.100:26".

SMTP Username and password

Input a user account and password for the SMTP server.

E-mail address

The recipients who will receive these logs, you can assign more than 1 recipient, using ';' or ',' to separate these email addresses.

E-mail Subject

The subject of email alert, this setting is optional.

View Log…

View the current system log.



Adv

ancedSetting>DynamicDNS



The Dynamic DNS fea their internet connection IP address is dynamic. By mapping the host name to the current public IP address of the router,

router or any router connects to the Internet.

ture ena

bles users to have a

ser

vices behind the router from the internet can just use

sta

tic domain name for

their internet connection even when

the Dynamic DNS hostname instead of the IP Address which might change every

Bef

ore you can use Dynamic DNS ser

TZO.com or dhs.org. After registering the account, the Dynamic DNS provider

•

Host Name

•

Username/Email

•

Password/Key.

ena

ble the Dynamic DNS fea

Click “Sa

ve” to save

the settings or “Undo” to cancel.

vice, you need to register an account on one of the many

ture on the unit, click the Ena

ble check box, choose the respective Provider and

will provide you with the f

supported Dynamic

ollowing details:

enter the details from your provider.

AdvancedSetting>QOS

users who want to connect to the

DNS provider such as DynDNS.org,

time the



QoS (Quality of Service) provides different priority to different users or data flows, or guarantees a certain level of performance.

QoS Control: This Item enables QoS function or not.

Bandwidth of Upstream: Set the limitation of upstream speed.

Local IP: Ports

Define the Local IP address and port to apply QoS to.

Remote IP: Ports

Define the Remote IP address and port to apply QoS to.

QoS Priority: This defines the priority level of the current Policy Configuration. Packets associated with this policy will be serviced based upon

the priority level set. For critical applications High or Normal levels are recommended. For non-critical applications select a Low level.

User Rule#: The QoS rules can work in conjunction with Scheduling Rules. Please reference the section Advanced setting/schedule Rule

section.

Click on “Save” to store your setting or “Undo” to discard your changes.

AdvancedSetting>SNMP

SNMP (Simple Network Management Protocol) is a protocol designed to give a user the capability to remotely manage a computer network by

polling and setting terminal values and monitoring network events.

Enable SNMP: You must check Local, Remote or both to enable SNMP function. If Local is checked, this device will only respond to requests

from LAN connected hosts. If Remote is checked, this device will respond to requests from the WAN connection.

Get Community: Sets the community string your device will respond to for Read-Only access.

Set Community: Sets the community string your device will respond to for Read/Write access.

IP 1, IP 2, IP 3, IP 4: Input your SNMP Management host IP here. You will need to configure the address where the device should send SNMP

Trap messages to.

SNMP Version: Please select proper SNMP Version that your SNMP Management software supports.

WAN Access IP Address: You can limit remote access to a specific IP address by entering it here.

Please note: If "Remote" access is enabled, the default setting of 0.0.0.0 means any IP obtain SNMP protocol information.

Click on “Save” to store your setting or “Undo” to discard your changes.



AdvancedSetting>Routing



Routing tables allow you to de ter mi ne wh i ch p hysi c al int erf a ce ad dre s s to use f or ou t go ing IP dat a. If yo u ha ve mor e tha n on e r outer and subnet, you will need to configure the routing

table to allow packets to find th e pro per rou tin g pat h an d al lo w di f fer ent sub n ets to co m mu ni c ate wit h ea ch ot her .

These settings are used to setup th e st ati c an d dy namic routing features of the 3G25 W- R .

Dynamic Routing:

Routing Information Pr ot oc ol (RIP) w ill ex ch an ge infor m ati o n ab o ut different host destinations for w ork in g o ut rou te s thr ou gh o u t the network. Please only select RIPv2 if you have a

different subnet in your netw or k. Ot he r wis e, pl ea se sel ect RI Pv 1.

Static Routing:

For static routing, you can specify up to 8 routing rules.

You need to enter the destination IP address, subnet mask, gateway, hop for each routing rule, and then enable the rule by clicking the Enable checkbox.

Click on “Save” to store your setti ng or “Un do” to dis ca rd y our ch an ge s.



Adv

anced

This page allows you to change the System time setting on the 3G25W-R.

Time Zone

Setting>SystemT

ime



Select the time zone where this device is located.

Auto-Synchronization

Select the “Enable” checkbox to enable this function.

Time Server

Select a NTP time server to obtain the current UTC time from

Sync with Time Server

Select if you want to set Date and Time by NTP Protocol.

Sync with my PC

Select if you want to set Date and Time using your computers Date and Time

Click “Sa

ve” to save

the settings or “Undo” to cancel.

Adv

ancedSetting>Sc

heduling



You can use scheduling to enable or disable a service at a specific time or on a specific day.

Select “Enable” and then click the “New Add” button. Select a name for the rule and enter the details such as the day, start time or end time.

Click “Sa

ve” to save

the settings or “Undo” to cancel.



oolBox

The T

ool Box page consists of various tools for

respective pa

ge.

the unit. Click on any of

the menu

items on

the left to access the

ool

Box>System

Info



From this page you can view the System log and the Routing Table

ool

Box>FirmwareUpgrade

You can upgrade the routers firmware by clicking the “Upgrade” button

information for

the router.

ool

Box>BackupSetting



You can backup your current settings by clicking the “ click the “Firmware Upgrade” button and use the bin file you saved.

ool

Box>ResettoDefault

Tool

Box>Reboot



Backup Setting

” button then and save it as a bin file. When you want to restore these settings,

AppendixA:

The WAN failover feature of the 3G25W-R is designed to provide a backup WAN connection in case your primary connection should fail. To use this feature, you will require both a regular WAN connection and a 3G WAN connection.

Please follow these steps to set up WAN failover on your 3G25W-R.

1. Set up a primary (non-3G) WAN connection by following the steps outlined in the Basic Setting > Primary Setup section of the User Guide.

2. Set up a secondary (3G) WAN connection by following the steps outlined in the Basic Setting > Primary Setup section of the User Guide.

3. Open your web browser (e.g. Internet Explorer/Firefox/Safari) and navigate to http://192.168.1.1/.

4. At the login screen, type in “admin” (without quotes) in the System Password field. Then click on Login.

5. Navigate to the Basic Setting > Primary Setup page. Select the Activate WWAN for Auto-Failover checkbox and enter a public IP address (for example ‘www.google.com’) into the remote host for keep alive box. The 3G25W-R will periodically check that it can connect to this address to determine if the WAN connection is still running.

6. In Basic Setting > Primary Setup, make sure that the selected WAN Type is your primary (non-3G) WAN connection and click Save. You are now ready to use the internet connection as normal.

WANFailover

7. When your primary (non-3G) WAN connection fails, the 3G25W-R will automatically failover to the secondary (3G) WAN connection. Please allow up to 2 minutes for this change to occur.

8. When your primary (non-3G) WAN connection reconnects, the 3G25W-R will automatically revert to this connection. Please allow up to 2 minutes for this change to occur.

9. To confirm that the process in Step 8 is complete, refresh the status page of the web interface after 1 minute.

AppendixB:EstablishingyourWirelessConnection



WindowsXPservicepack2

1. Open Network Connections (Start -> Control Panel -> Network Connections):

2. Right-click on your Wireless Network Connection and select View Available Wireless Networks:

3. Select the wireless network you want to connect to and click Connect:

4. Enter the network key (“a1b2b3d4e5”) and click Connect:

5. The connection will show Connected.



WindowsVista

1. Open Network and Sharing Center (Start > Control Panel > Network and Sharing center).

2. Click on “Connect to a network”.

3. Choose “Connect to the Internet” and click on “Next”.

4. Choose “NetComm n3G Series”.

5. Click on the wireless network name and click “Connect”.

6. Click on “Display Characters” and type in the network key. Then Click “Next”.

7. Select the appropriate location. This will affect the firewall settings on the computer.

8. Click on both “Save this network” and “Start this connection automatically” and click “Next”.



Windows7

Follow these steps:

1. Open Network and Sharing Center (Start > Control Panel > Network and Sharing center).

2. Click on "Change Adapter settings" on the left-hand side.

3. Right-click on "Wireless Network Connection" and select "Connect / Disconnect".

4. You should see a network listed with the SSID of your 3G25W-R. Select your wireless network and click “Connect”.

5. Type the following into the “Security key” section: a1b2c3d4e5 and click "OK".

6. You may then see a window that asks you to "Select a location for the 'wireless' network". Please select the "Home" location.

7. You may then see a window prompting you to setup a “HomeGroup”. Click “Cancel” on this.

8. You can verify your wireless connection by clicking the “Wireless Signal” indicator in your system tray. After clicking on this, you should see an

entry matching the SSID of your 3G25W-R with “Connected” next to it.



MacOSX10.6

Follow these steps:

1. Click on the Airport icon on the top right menu.

2. Click on the network name that you want to connect.

3. On the new window, tick on Show Password and type in the network key in the Password field. Click on OK.

4. To check the connection, click on the Airport icon and there should be a tick on the wireless name.

Notes:Forotheroperatingsystem(Windows98SE,WindowsME,Windows2000etc)orifyouusethewireless

adaptorutilitytoconfigureyourwirelessconnection,pleaseconsultthewirelessadapterdocumentationfor

additionalinformation.

AppendixC:Troubleshooting

UsingLEDstoDiagnoseProblems

The LEDs are useful aides for finding possible problem causes.

Power LED

The Power LED does not light up.

Step

1

2

3

4

Correct Action

Make sure that the 3G25W-R power adaptor is connected to the device and plugged in to an appropriate power source. Use only the supplied power adaptor.

Check that the 3G25W-R and the power source are both turned on and device is receiving sufficient power.

Turn the 3G25W-R off and on.

If the error persists, you may have a hardware problem. In this case, you should contact your vendor.

WebConfiguration

I cannot access the web configuration.

STEPS CORRECTIVE ACTION

Step

3 4

Correct Action

Make sure you are using the correct IP add r ess of the 3G25W-R. Check the IP address of the device.

Check that you have enabled web service access. If you have configured a secured client IP address, your computer’s IP address must match it.

Your computer’s and the 3G25W-R’s IP addresses must be on the same subnet for LAN access. If you changed the devices WLAN IP address, then enter the new one a s the URL.



The web configuration does not display properly.

Step

Correct Action

Delete the temporary web files and log in again. In Internet Explorer, click Tools, Internet Options and then click the Delete Files ... button. When a Delete Files window displays, select Delete all offline content and click OK. (Steps may vary depending on the version of your Internet browser.)

CORRECTIVE ACTION

I forgot my login username and/or password.

Step 1

S CORRECTIVE ACTION

Correct Action

If you have changed the password and have now forgotten it, you will need to upload the default configuration file. This will erase all custom configurations and restore all of t he factory defaults including the pa ssword.

Press the Reset button for ten seconds, and then release it. When the LINK LED begins to blink, the defaults have been restored and the 3G25W-R restarts.

The default username is “admin”. The default password is “admin”. The Password and Username fields are casesensitive. Make sure that you enter the correct password and username using the proper casing.

It is highly recommended to change the default username and password. Make sure you store the username and password in a save place.



WLANInterface

I cannot access the 3G25W-R from the WLAN or ping any computer on the WLAN.

Step

1 2

TE CORRECTIVE ACTION

Correct Action

Check the WiFi LEDs on top of the unit Make sure that the IP address and the subnet mask of the NB14WN and your computer(s) are on the same subnet.

InternetAccess

I cannot access the Internet.

STEPS COR

Step

1 2

RECTIVE ACTION

Internetconnectiondisconnects.

Step

1 2

TEPS CORRECTIVE ACTION

Correct Action

Make sure the 3G25W-R is turned on and connected to the network. Verify your 3G settings

Correct Action

Check the schedule rules. Contact your 3G SIM provider

LegalandRegulatoryInformation



FCC Statement:



This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This eq uipment generates,

uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference

to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one of the following measures:

 Reorient or relocate the receiving antenna.

 Increase the separation between the equipment and receiver.

 Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

 Consult the dealer or an experienced radio/TV technician for help.

FCC Caution:

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this

equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and

2. this device must acc ept any in t er ference received, inc l uding interference that may cause undesired operation.

Important Note:

FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and

operated with a minimum distance of 20cm between the radiator and your body.

The transmitter must not be co-located or operating in conjunction w ith any other antenna or transmitter.

Industry Canada RF exposure requirements

In order to ensure compliance with the RF exposure requirements specifie d in Health Canada Safety Code 6, this device may

be operated while held in the hand, but not when he ld close to the body, carried in a pocket or holster, or similar configuration

that allows close proximity to the body.”

NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED

MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER'S AUTHORITY TO OPERATE THE

EQUIPMENT.

ThisdevicecomplieswithIndustryCanadalicence‐exemptRSSstandard(s).

Operationissubjecttothefollowingtwoconditions:

(1)thisdevicemaynotcauseinterference

(2)thisdevicemustacceptanyinterference,includinginterferencethatmaycauseundesiredoperationofthedevice.

This Class [ B ] digital apparatus complies with Canadian ICES-003.

This device has been designed to operate with the antennas listed below, and having a maximu m gain of [ 4 ]dB.

Antennas not included in this list or having a gain greater than [ 4 ]dB are strictly prohibited for use with this device. The

required antenna impedance is [ 50 ] ohms.



This product includes copyrighted third-party software licensed under the terms of the GNU General Public License. Please refer to the GNU General Public License below to check the detailed terms of this license. The following parts of this product are subject to the GNU GPL, and those software packages are copyright by their respective authors. Linux-2.6.21 system kernel busybox_1_00_rc2 bridge-utils 0.9.5 dhcpcd-1.3 ISC DHCP V2 P5 syslogd spread from busybox wireless tools ntpclient of NTP client implementation GNU Wget Availability of source code Please visit our web site or contact us to obtain more information.

GNU GENERAL PUBLIC LICENSE

Version 2, June 1991

59 Temple Place, Suite 330, Boston, MA 02111-1307 USA

Everyone is permitted to copy and distribute verbatim copies

of this license document, but changing it is not allowed. Preamble The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General Public License is intended to guarantee your freedom to share and change free software--to make sure the software is free for all its users. This General Public License applies to most of the Free Software Foundation's software and to any other program whose authors commit to using it. (Some other Free Software Foundation software is covered by the GNU Library General Public License instead.) You can apply it to your programs, too. When we speak of free software, we are referring to freedom, not price. Our General Public Licenses are designed to make sure that you have the freedom to distribute copies of free software (and charge for this service if you wish), that you receive source code or can get it if you want it, that you can change the software or use pieces of it in new free programs; and that you know you can do these things. To protect your rights, we need to make restrictions that forbid anyone to deny you these rights or to ask you to surrender the rights. These restrictions translate to certain responsibilities for you if you distribute copies of the software, or if you modify it. For example, if you distribute copies of such a program, whether gratis or for a fee, you must give the recipients all the rights that you have. You must make sure that they, too, receive or can get the source code. And you must show them these terms so they know their rights. We protect your rights with two steps: (1) copyright the software, and (2) offer you this license which gives you legal permission to copy, distribute and/or modify the software. Also, for each author's protection and ours, we want to make certain that everyone understands that there is no warranty for this free software. If the software is modified by someone else and passed on, we want its recipients to know that what they have is not the original, so that any problems introduced by others will not reflect on the original authors' reputations. Finally, any free program is threatened constantly by software patents. We wish to avoid the danger that redistributors of a free program will individually obtain patent licenses, in effect making the program proprietary. To prevent this, we have made it clear that any patent must be licensed for everyone's free use or not licensed at all. The precise terms and conditions for copying, distribution and modification follow.

GNU GENERAL PUBLIC LICENSE

TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION

0. This License applies to any program or other work which contains a notice placed by the copyright holder saying it may be distributed under the terms of this General Public License. The "Program", below, refers to any such program or work, and a "work based on the Program" means either the Program or any derivative work under copyright law: that is to say, a work containing the Program or a portion of it, either verbatim or with modifications and/or translated into another language. (Hereinafter, translation is included without limitation in the term "modification".) Each licensee is addressed as "you". Activities other than copying, distribution and modification are not covered by this License; they are outside its scope. The act of running the Program is not restricted, and the output from the Program is covered only if its contents constitute a work based on the Program (independent of having been made by running the Program). Whether that is true depends on what the Program does.

1. You may copy and distribute verbatim copies of the Program's source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty; keep intact all the notices that refer to this License and to the absence of any warranty; and give any other recipients of the Program a copy of this License along with the Program. You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee.

2. You may modify your copy or copies of the Program or any portion of it, thus forming a work based on the Program, and copy and distribute such modifications or work under the terms of Section 1 above, provided that you also meet all of these conditions: You must cause the modified files to ca rry prominent notices stating that you changed the files and the date of any change. You must cause any work that you distribute or publish, that in whole or in part contains or is derived from the Program or any part thereof, to be licensed as a whole at no charge to all third parties under the terms of this License. If the modified program normally reads commands interactively when run, you must cause it, when started running for such interactive use in the most ordinary way, to print or display an announcement including an appropriate copyright notice and a notice that there is no warranty (or else, saying that you provide a warranty) and that users may redistribute the program under these conditions, and telling the user how to view a copy of this License. (Exception: if the Program itself is interactive but does not normally print such an announcement, your work based on the Program is not required to print an announcement.)

These requirements apply to the modified work as a whole. If identifiable sections of that work are not derived from the Program, and can be reasonably considered independent and separate works in themselves, then this License, and its terms, do not apply to those sections when you distribute them as separate works. But when you distribute the same sections as part of a whole which is a work based on the Program, the distribution of the whole must be

on the terms of this License, whose permissions for other licensees extend to the entire whole, and thus to each and every part regardless of who wrote it. Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather, the intent is to exercise the right to control the distribution of derivative or collective works based on the Program. In addition, mere aggregation of another work not based on the Program with the Program (or with a work based on the Program) on a volume of a storage or distribution medium does not bring the other work under the scope of this License.

3. You may copy and distribute the Program (or a work based on it, under Section 2) in object code or executable form under the terms of Sections 1 and 2 above provided that you also do one of the following: Accompany it with the complete corresponding machine-readable source code, which must be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interch ange; or, Accompany it with a written offer, valid for at least three years, to give any third party, for a charge no more than your cost of physically performing source distribution, a complete machine-readable copy of the corresponding source code, to be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange; or, Accompany it with the information you re ceived as to the offer to distribute corresponding source code. (This alternative is allowed only for noncommercial distribution and only if you received the program in object code or executable form with such an offer, in accord with Subsection b above.)

The source code for a work means the preferred form of the work for making modifications to it. For an executable work, complete source code means all the source code for all modules it contains, plus any associated interface definition files, plus the scripts used to control compilation and installation of the executable. However, as a special exception, the source code distributed need not include anything that is normally distributed (in either source or binary form) with the major components (compiler, kernel, and so on) of the operating system on which the executable runs, unless that component itself accompanies the executable. If distribution of executable or object code is made by offering access to copy from a designated place, then offering equivalent access to copy the source code from the same place counts as distribution of the source code, even though third parties are not compelled to copy the source along with the object code.

4. You may not copy, modify, sublicense, or distribute the Program except as expressly provided under this License. Any attempt otherwise to copy, modify, sublicense or distribute the Program is void, and will automatically terminate your rights under this License. However, parties who have received copies, or rights, from you under this License will not have their licenses terminated so long as such parties remain in full compliance.

5. You are not required to accept this License, since you have not signed it. However, nothing else grants you permission to modify or distribute the Program or its derivative works. These actions are prohibited by law if you do not accept this License. Therefore, by modifying or distributing the Program (or any work based on the Program), you indicate your acceptance of this License to do so, and all its terms and conditions for copying, distributing or modifying the Program or works based on it.

6. Each time you redistribute the Program (or any work based on the Program), the recipient automatically receives a license from the original licensor to copy, distribute or modify the Program subject to these terms and conditions. You may not impose any further restrictions on the recipients' exercise of the rights granted herein. You are not responsible for enforcing compliance by third parties to this License.

7. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to patent issues), conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not excuse you from the conditions of this License. If you cannot distribute so as to satisfy simultaneously your obligations under this License and any other pertinent obligations, then as a

consequence you may not distribute the Program at all. For example, if a patent license would not permit royaltyfree redistribution of the Program by all those who receive copies directly or indirectly through you, then the only way you could satisfy both it and this License would be to refrain entirely from distribution of the Program. If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply and the section as a whole is intended to apply

in other circumstances. It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of any such claims; this section has the sole purpose of protecting the integrity of the free software distribution system, which is implemented by public license practices. Many people have made generous contributions to the wide range of software distributed through that system in reliance on consistent application of that system; it is up to the author/donor to decide if he or she is willing to distribute software through any other system and a licensee cannot impose that choice. This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License.

8. If the distribution and/or use of the Program is restricted in certain countries either by patents or by copyrighted interfaces, the original copyright holder who places the Program under this License may add an explicit geographical distribution limitation excluding those countries, so that distribution is permitted only in or among countries not thus excluded. In such case, this License incorporates the limitation as if written in the body of this License.

9. The Free Software Foundation may publish revised and/or new versions of the General Public License from time to time. Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems or concerns. Each version is given a distinguishing version number. If the Program specifies a version number of this License which applies to it and "any later version", you have the option of following the terms and conditions either of that version or of any later version published by the Free Software Foundation. If the Program does not specify a version number of this License, you may choose any version ever published by the Free Software Foundation.

10. If you wish to incorporate parts of the Program into other free programs whose distribution conditions are different, write to the author to ask for permission. For software which is copyrighted by the Free Software Foundation, write to the Free Software Foundation; we sometimes make exceptions for this. Our decision will be guided by the two goals of preserving the free status of all derivatives of our free software and of promoting the sharing and reuse of software generally. NO WARRANTY

11. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE PROGRAM "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION.

12. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE PROGRAM AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES,

INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

END OF TERMS AND CONDITIONS



NetComm Wireless 3G25WR User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual