NetComm V90s User Manual

V90s Desktop IP Phone

IP Telephone with Power over Ethernet (PoE) Support

KEY FEATURES

Power over Ethernet (802.3af) Support

Setup Wizard for different types of network environment and IP phone accounts

Auto Configuration Support via TFTP and HTTP (Plug-n-Play operation)

Smart Firmware Management Support via TFTP and HTTP

Primary and Backup SIP server support for primary proxy server failover and network redundancy (single server mode only)

Programmable QoS Marking (both 802.1q VLAN and ToS/DiffServ)

Compatibility in multi- vendor open architecture VoIP networks

Retrieving time via NTP Servers and SIP message

NAT/ Firewall Traversal Support with Border Session Controller or Stun Server

Support for 4 VoIP Accounts/SIP Proxies

Features

NetComm’s V90 is the ideal device to take advantage of the benefits of VoIP
Telephony services. Adding to the V90’s elegant design are a host of features
including Full Duplex Speaker Phone with echo cancellation, speed dials, phone
book, call transfer, mute and a unique volume control for both the handset
speaker/microphone.

Standards Based

The V90 is fully compliant with IETF SIP 2.0 specification which ensures that it will
run smoothly and error free.

POE Support

Power-over-Ethernet (PoE) or “Active Ethernet” lets you run a single CAT5 Ethernet
cable to carry both power and data to devices on the LAN. This eliminates the need
to run separate 240 Volt power to devices on a wired LAN.

It also allows greater flexibility in locating IP Phones and significantly decreases
installation costs. With Power over Ethernet, you can power network devices up
to 328 feet (100 meters) away, using standard CAT5 Ethernet cable.

As standard, the V90 is supplied as both a POE and DC powered terminal.
With full 802.3af compliance, the V90 can be powered over Ethernet by any
standards based POE switch or power injector.

www.dynalink.co.nz

V90s Desktop IP Phone

IP Telephone with Power over Ethernet (PoE) Support

TECHNICAL SPECIFICATIONS

Standards Supported

• SIP V2.0 Standard (RFC 3261)

• SDP (RFC 2327)

• Digest authentication and MD5 encryption (SIP)

• ITU-T G.711 Alaw/Ulaw, G.729A, G.729AB,

G.723.1

• RTP (Real Time Transmission Protocol) RFC1889

• RTCP (Real Time Transport Control Protocol)

RFC 3550

• Proprietary Firewall-Pass-Through Technology

• Simple Traversal of UDP over NAT (STUN)

• Web-based Management

• PPP over Ethernet (PPPoE)

• PPP Authentication Protocol (PAP)

• Internet Control Message Protocol (ICMP)

• TFTP Client

• Hyper Text Transfer Protocol (H TT P)

• Dynamic Host Configuration Protocol (DHCP)

• Domain Name System (DNS)

• Out-band DTMF Relay: RFC 2833 and SIP Info

• SIP prox y address in DHCP (RFC 3361)

Software Features

• Built-in HT TP, Phone Menu for accessing internal

parameters

• PPPoE Client

• NAT Broadband Router functions

• DHCP Client

• DHCP Server

• Firmware On-line upgrade

• Phone Book

• Memory Dial

• Speed Dial

• Caller ID

• Multiple Language Support

Hardware Interface

• Ethernet PC & Network Port (2 x RJ-45,

10/100BaseT)

• DC Jack

• Headset Port

Centralised configuration and management

The V90 terminal can download a configuration file from an HTTP server that will prompt it to upgrade its firmware
file. A DHCP server is used to assign an IP address to the V90 phone and inform the V90 of the HTTP address
of the configuration file.

Programmable Function Keys

The V90 features 5 user programmable keys that can be used for speed dialling or any number of common
everyday tasks.

Quality of Service

The built in QoS of the V90 guarantees that call quality is maintained and monitored to give you crisp clear
calls with no drop out or stuttering.

Key Features

SIP 2.0 standardization deployed throughout

Advanced audio processing – jitter buffer with packet delay and packet loss concealment

Voice packetization & flexible voice compression

Programmable voice packet payload size

Centralised control of codec negotiation

In-band and Out-band DTMF transport

G.168 Echo Cancellation

Two Ethernet ports supporting router and bridge mode

Call Redial, Flash, Mute

Caller ID / Call Waiting

Call Hold/Forward/Conference/Transfer (attended/unattended call transfer)

Phone Book Memory Dialing

Speed Memory Dialing

Hands Free Dialing

Hotline Dialing

Call history for incoming, outgoing and missed calls

Programmable Generic Function Key Definitions (automatic adding prefixes/customized LCD menu)

Soft Login/Logout key for SIP registration

128x64 dot matrix LCD with back light

Full Duplex Speakerphone

Auto Provisioning Support

Firmware upgrading, loading configuration, phone status reports via Centralized Management tool

Local Music on Hold

Your NetComm dealer:

NETCOMM LIMITED ABN 85 002 490 486 PO Box 1200, Lane Cove NSW 2066 Australia

P: 02 9424 2070 F: 02 9424 2010 E: [e-mail] W: www.netcomm.com.au

Trademarks and registered trademarks are the property of NetComm Limited or their respective owners. Specifications are subject to change without notice. Images shown may vary slightly from the actual product.

DYNALINK NZ 224b Bush Road, Albany, Auckland, New Zealand
P: 09 448 5548 F: 09 448 5549 E: [e-mail] W: www.dynalink.co.nz