NETCOM POE
REMOTE POWER SUPPLY ETHERNET SWITCH
USER'S MANUAL
NETCOM PO E Switch User’s Manual
2
PREFACE
Version directions:
This manual corresponds to NETCOM POE series versionV1.1.
NETCOM PSE NETCOM POE Series
1. NETCOM POE01
2 .NETCOM POE04
3. NETCOM POE08
Target reader
The reader of this manual is NETCOM POE series users
Related Manuals
This manual explores "Installation Manual" of NETCOM POE series
Article structure
List the basic content of the manual, including the name and main purpose
of Chapters.
Chapter 1 System Overview
Describes NETCOM POE features
Chapter2 Structure of electrical connections
Describes the appearance and pin definitions of NETCOM POE
Chapter3 Installation and commissioning
Describes installation and commissioning of NETCOM POE
Chapter4 Routine maintenance
Describes maintenance of NETCOM POE series
Chapter5 Transport storage
Describes the transport issue of NETCOM POE series
3
CONTENTS
Chapter 1 System Overview. ................................................................................. 4
1.1 Features and functions ............................................................................ 4
1.2 Technical features and Specifications ...................................................... 6
Chapter 2 Electrical connection and structure. ....................................................... 9
2.1 The structure and outline picture of NETCOM POE8 ............................ 9
2.2 Display and control panel .................................................................... 12
Chapter 3 installation and debugging ................................................................. 15
3.1 Open case inspection ............................................................................. 15
3.2 Installation ............................................................................................ 15
3.3 Start test ............................................................................................... 16
Chapter 4 Routine maintenance .. ................................................................... 17
4.1 Routine maintenance ............................................................................. 17
Chapter 5 Transport and storage.. ................................................................... 18
5.1 Transport ................................................................ ............................ 188
5.2 Storage ................................................................................................. 18
4
Chapter 1 System Overview
Content
Features and functions
Operating environment
Technical features and parameters
This chapter describes features and functions of NETCOM POE series
1.1 Features and functions
NETCOM POE which is designed specifically for Telecom carrier . The
device implemented advanced MCU control technology. Total power,
individual port power, port status and device temperature are displayed on LCD
real time. And it has efficient protection of each port. It is used with wireless
AP, IP cameras, VOIP and other device that needs network and power supply.
1. LCD display and control panel, display the total power, power of each port,
the device temperature, etc. ( only for 8 port POE)
2. The entire device or any single port reset ( only for 8 port POE)
3. The POE and UPLINK port support automatic MDI/MDI-X function
4. Supply 4 or 8 POE power port, one UPLINK port
5. 10/100Mbps, full/half duplex automatic adapt
6. Compliant with IEEE802.3af, IEEE802.3at standard, 25W Max per port
7. Backplane switching capacity of 1.0Gbps
8. 2K MAC address list
5
9. Extend the cable transmit distance, furthest to 300m. ( only for 4 port POE)
10. Effective short circuit, overload and total power protection
11. Each port with indicator light, alarm light, device alarm light
12. Metal case, with wall mounting hole
6
1.2 Technical features and Specifications
Technology Specifications
IEEE standard
IEEE 802.3 10Base-T Ethernet
IEEE 802.3u 100Base-TX Fast Ethernet
IEEE 802.3x Flow Control and Back Pressure
IEEE 802.3af Power Over Ethernet
IEEE 802.3at Power Over Ethernet
switching structure
Back-plane( switch ):1.0Gbps
Transfer Rate: 14,880pps for Ethernet port
148,800pps for Fast Ethernet port
Transmit rate
Ethernet ：10Mbps half duplex，20Mbps full duplex
Fast Ethernet：100Mbps half duplex，200Mbps full duplex
Mac address
2K MAC address list
interface
10/100TX：RJ-45，all ports support automatic
MDI/MDI-Xfunction
4 port POE or 8 port POE
Port protection
Effective short circut ,overload and total power
protection
Cable type and
distance
10BASE-T：
CAT 3，4，5 UTP （maximum length 100m ）
EIA/TIA-568 100 OHM STP（maximum length 100m）
100BASE-TX：
CAT 5E UTP（maximum length 100m）
EIA/TIA-568 100 OHM STP （maximum length 100m）
7
Cable extend distance
200m （only for POE04 switch )
POE PINs
Support A B mode
Positive (VCC+)：RJ-45 pin 1，2，4，5
Negative (VCC-)：RJ-45 pin 3，6，7，8
Data (1，2，3，6)
Protocols
CSMA/CD
Power supply
External Power Adaptor (POE04)
(100V-240V AC 50Hz-60Hz， DC48V/ 2.5A)
Internal power adaptor (POE08)
(200V-240V AC 2A 50Hz-60Hz)
Overcurrent protection
Implemented
Storage temperature
-20°C－+70°C
Operating
temperature
-10℃ ～+ 50℃ 5%～95% Non-condensing
8
Dimensions and weight：
NETCOM POE01
NETCOM POE04
NETCOM POE08
Width
58mm
155.6mm
270mm
Height
38mm
26mm
44mm
Depth
120mm
71.4mm
170mm
Weight
<0.3kg
<0.5kg
<3kg
NETCOM POE series protect function：
Range of output over-voltage protection：52VDC
Over current protection (single channel)：750mA
Over voltage protection：Input voltage is over 260VAC
Over voltage recovery point：Input voltage is below 255VAC
low voltage protection：90VAC(POE04) / 140VAC(POE08)
Voltage recovery point：95VAC (POE04) /165VAC (POE08)
Over-temperature protection：100℃
9
Chapter2 Electrical connection and structure
Contents
The structure and outline picture of NETCOM POE
Display and control panel
Main content: Introduce the structure and the connection way of NETCOM
POE8
2.1 The structure and outline picture
NETCOM POE08
NETCOM POE04
NETCOM PSE01
10
Ethernet port lights instructions：
POE04 LED Description
Indicator Light
Color
State
Indicator Light signification
Power
Green
on
normal power supply for device
off
No power supply for the device
Alarm
Red
Flashing
The device with problem of any
port or power overload
off
Normal status
Link/Act(Uplink)
Green
on
Port is connected
Flashing
Device Port in the transmission
or reception of data
off
Device Port is not connected
POE(Uplink)
Green
on
Device is drawing power from
uplink port
off
Device is not drawing power
from uplink port
Link/Act(1-4)
Green
on
Device Port is connected
Flashing
Device Port in the transmission
or reception of data
off
Device Port is not connected
POE(1-4)
Green
on
Normal power supply for remote
device
Flashing
port overload or other failure
off
No power supply for remote
power supply
POE 8 Power switch LED Description
11
Indicator
Light
Color
State
Indicator Light signification
Power
Green
on
normal power supply for device
off
No power supply for the device
Alarm
Red
Flashing
The device with problem of any port or
power overload
off
Device output port without problem
Link(Uplink)
Green
on
Port is connected
Flashing
Device Port in the transmission or
reception of data
Act(Uplink)
Green
off
Device Port is not connected
on
The device port receive the remote power
supply
Link/Act(1-8)
Green
Flashing
Device Port in the transmission or
reception of data
off
Device Port is not connected
on
Port connected
POE(1-8)
Green
Flashing
port overload or other failure
off
No power supply for remote power
supply
on
Normal power supply for remote device
12
2.2 Display and control panel(POE08 only)
The “SELECT” key: Choose a port of display
The “RESET” key: Reset the entire device or the selected port
Ordinary POE devices do not display how much the total power and the
individual port power it used, load the equipment also can not be understand;
When a port is overloaded or short circuit, you can not turn off the power
output port, there are some security risks; when using a part of the port in the
device, the total power is over the device rate power, it works abnormal. To
solve these problems, Wanglu Communication Company has developed a more
perfect POE device for telecom carrier with liquid crystal display and control
panel. Total power, individual port power, port status and device temperature
are displayed on LCD, through the front panel, User can reset the whole device
or any individual port
⑴ When the device self-test complete, company information, total
power, operation temperature, fan state are displayed on LCD
⑵Reset all device ports
In main frame screen state, press the “RESET” key, display “again to
confirm”, and press again the RESET key to reset the whole device.
Notice: All channels reset, will cause the power of all the channels shutoff
instantaneously.
⑶ Display an individual port power or failure
13
In main frame screen state, press the SELECT key, display selected
port, and press the “SELECT” key continuously to choose other ports.
When Channel works normally, display the power value
Channel is abnormal, show-related malfunction
Channel overload display "Overload"
Channel short circuit: Display "fail”
(4) Reset a port
When a channel occurs malfunction, the device will try to return to normal
working condition itself twice, if after two attempts it can not return to normal,
the device will disable the port with lights flashing, ALARM flash, and the
malfunction are displayed on LCD . Construction personnel must check the
external device or network cable which connects to the port, after solved
problem, it will be working normally after resetting the port.
When display selected channel; Press the“RESET”key, reset the port
14
⑸fan start and stop
The device has a monitoring temperature features, when the temperature
exceeds 42 ℃, the fan start, it can help the device cool down, the fan sign are
displayed on LCD
When the temperature dropped below 38 ℃, the fan stop working and the fan
sign is off on LCD.
15
Chapter 3 installation and debugging
Content
open-case inspection
installation
start test
Main content: Introduce common operations of installation and debugging of
NETCOM POE series
3.1 Open case inspection
Check the attachment whether complete, it contains:
1. POE device
A user’s manual
An input power cable
48V Power adaptor(POE04 only)
2. Checking the machine whether damaged, deformed or rusty.
If it is found that the sorts of equipment components or the
quantities does not consistent with the description, or equipment
is damaged in transit, etc., Please contact us in time.
3.2 Installation
(1) Power cord be plugged into 220VAC input socket.
(2) Connecting up the output signal wire individually. (Picture 2-4).
(3) AC power cord, signal wire, the output line be connected fastened,
in order to avoid poor contact and loose.
Notice ：
16
1：The POE device must be placed far away from the heat source,
source of electromagnetic interference, corrosive gases and metal
dirt.
2：Do not block the cooling hole of the device.
3: Installation must be placed smoothly, without strenuous vibration.
4：make sure the AC input voltage range.
5：During the installation, it should prevent from Collision and
friction between the equipments, to avoid local damage of the
machine surface.
3.3 Start test
⑴ after loading, it is normal if displayed green light in the output port;
light flashes to indicate a short circuit and current limiting phenomena;
ALARM light is on, indicating that the device has malfunction.
⑵After the AC power on, the front panel” POWER” light is on.
⑶Total power, company information, the operating temperature and the
fan star and stop state etc. are displayed on LCD.
17
Chapter 4 Routine maintenance
Content
Routine maintenance
Main content: Introduce NETCOM POE series routine maintenance
and operation.
4.1Routine maintenance
NETCOM PSE series can operate successively; it guarantees the
reliability for the power supply. To do routine maintenance is necessary,
and makes the power system in the best state during the operating.
(1) Clean the power source regular, prevent the dust accumulation
(2) Check the connection of input and output line whether loose or poor
contact, if damaged, please change in time.
18
Chapter 5 Transport and storage
Content
Transport
Storage
Main content: NETCOM POE series transport and the storage that need
attention
5.1 Transport
NETCOM PSE series should be put gently in transit, or prevent it to severe
shock. .It should be placed strictly accordance with the box direction, if
violated may result in malfunction and damage.
5.2 Storage
It should keep in dry storage warehouse, no direct sunlight or rain.
The placed direction should be consistent with the box mark, storage period is
one year.
The storage temperature: –20℃～+70℃(after storage in low temperature, the
restoration time is four hours at least )
Relative humidity: 5%～90%RH
Loading...