Ness 101-091, 101-091B, XK Installation Manual
101-091 / 101-091B
Ultraprox Bluetooth Keypad/Reader
INSTALLATION & USER MANUAL
Innovative Electronic Solutions
Rev 1.0
CONTENTS
INTRODUCTION…………………..................................................................................…………………1
INSTALLATION…………………………..................................................................................……………3
STANDALONEMODE……....................................................................................………………………5
CONTROLLERMODE……….................................................................................………………………11
WIEGANDREADERMODE……....................................................................................………………13
ADVANCEDAPPLICATION…………..............................................................................……………..15
1
INTRODUCTION
The XK Series device is a single door multifunction standalone access controller or a Wiegand output reader. It uses
Atmel MCU assuring stable performance. The operation is very user-friendly, and low-po wer circuit makes it long
service life.
The XK Series device supports 1,000 users (998 common users + 2 panic users), all user data can be transferred from
one to another. It supports multi access modes in either card access, PIN access, Card + PIN access, or multi cards/PINs
access. It has extra features including block enrollment, interlocked, Wiegand 26~37 bits interface, etc th at are
highlighter below.
Features
Bluetooth Module, to connect mobile App for opening door
Fashion design, all-metal key button
Metal Case, Anti-vandal
Waterproof, conforms to IP66
One relay, 1,000 users (998 common users + 2 panic users)
PIN length: 4~6 digits
Card type:
EM version: 125KHz EM card
Wiegand 26~37 bits input & output
Can be used as Wiegand reader with LED & Buzzer output
Card block enrolment
Tri-colour LED status display
Integrated alarm & buzzer output
Pulse mode or Toggle mode
User data can be transferred
2 devices can be interlocked for 2 doors
Built in light dependent resistor (LDR) for anti tamper
Backlit keypad
Low temperature resistance (-40℃)
Voltage: 12~28V AC/DC
2
Specifications
User Capacity
Common User
Panic User
Operating Voltage
Idle Current
Proximity Card Reader
Radio Technology
Read Range
Wiring Connections Relay Output, Exit Button, Alarm, Door Contact,
Relay
Adjustable Relay Output Time
Lock Output Load
Wiegand Interface
Wiegand Input
Wiegand Output
Pin Output
Environment
Operating Temperature
Operating Humidity
Physical
Colour
Dimensions
Unit Weight
Shipping Weight
1000
998
2
12~28V AC/DC
＜35mA
EM Format
125KHz Proximity Card
2~6 cm
Wiegand Input, Wiegand Output
One (NO, NC, Common)
0~99 Seconds (5 seconds default)
2 Amp Maximum
Wiegand 26-37 bits
(Factory Default: Wiegand 26bits, 4 bits)
26-37 bits
26-37 bits
4 bits, 8 bits(ASCII), 10 digits Virtual Num ber
(Note: Set in the factory as 26 Bit Wiegand 10 Digit
Virtual No. If a factory reset is performed onsite then
these settings need to be manually reset.)
Meets IP66
-40℃ ~ 60℃ (-40℉~ 140℉)
0%RH~98%RH
Zinc-Alloy
Silver
L114.5 x W75 x D22mm(XK3)
L134 x W55.5 x D21mm (XK4)
340g
420g
3
Carton Inventory
INSTALLATION
Remove the back cover from the unit
Drill 2 holes(A,C) on the wall for the screws and one hole for the cable
Knock the supplied rubber bungs to the screw holes(A,C)
Fix the back cover firmly on the wall with 4 flat head screws
Thread the cable through the cable hole(B)
Attach the unit to the back cover
Wiring
Wire Color Function Notes
Basic Standalone Wiring
Red AC/DC 12-28V AC/DC Regulated Power Input
Black AC/DC 12-28V AC/DC Regulated Power Input
Pink GND Negative Pole
Blue Relay NO Normally Open Relay Output (install diode provided)
Purple Relay Common Common Connection for Relay Output
Orange Relay NC Normally Closed Relay Output (Install diode provided)
Yellow OPEN Request to Exit(REX) Input
Pass-Through Wiring (Wiegand Reade r or Controller)
Green Data 0 Wiegand Input /Output Data 0
White Data 1 Wiegand Input /Output Data 1
Advanced Input and Output Features
Grey Alarm Output Negative contact for Alarm
Brown Contact Input Door/Gate Contact Input (Normally Closed)
4
Sound and Light Indication
Operation Status LED Buzzer
Stand by Red light bright Enter into programming mode Green light Flashes on, then
RED Light flashes.
In the programming mode Orange light bright One beep
Operation error - Three beeps
Exit from the programming mode Red light bright One beep
Open lock Green light bright One beep
Alarm Red light Shines quickly Beeps
One beep
Basic Configure
Enter and Exit Program mode
Programming Step Keystroke Combination
Enter Program Mode
Exit Program Mode *
Set Master Code
Programming Step Keystroke Combination
1. Enter Program Mode
2. Update Master Code
3. Exit Program Mode *
Set the Working Mode
Notes: the XK Series device has 3 working modes: Standalone Mode, Controller Mode, Wiegand Reader Mode, choose
the mode you use. (Factory default is Standalone Mode / Contro ller Mode)
Programming Step Keystroke Combination
1. Enter Program Mode
2. Standalone/Controller Mode
OR
2. Wiegand Reader Mode
3. Exit *
* (Master Code) #
(Factory default is 123456)
* (Master Code) #
0（New Master Code）#（Repeat New Master Code）#
(Master code is any 6 digits)
* (Master Code) #
7 2 # (Factory default)
7 3 # (Pre-Set in the factory after a ‘Factory default’)
5
Loading...