Ness SmartLiving 505, SmartLiving 10100, SmartLiving 515, SmartLiving 1050 Installation Manual

Installation & Programming Manual

CEI 79-2 EN 50131-3 EN 50131-6 CEB T01

Ness Smart Living

Anti-intrusion Control Panels & Security Systems

INSTALLATION & PROGRAMMING MANUAL

Innovative Electronic Solutions

Anti-intrusion control panels

Warranty

Ness Corporation (as known as Ness in this document) warrants the original purchaser that this product shall be free from defects in materials and workmanship under normal use for a period of 24 months. As Ness does not install this product directly, and due to the possibility that it may be used with other equipment not approved by Us; Ness does not warrant against loss of quality, degradation of performance of this product or actual damage that results from the use of products, parts or other replaceable items (such as consumables) that are neither made nor recommended by Ness. Seller obligation and liability under this warranty is expressly limited to repairing or replacing, at Seller's option, any product not meeting the specifications. In no event shall Ness be liable to the purchaser or any other person for any loss or damage whether direct ot indirect or consequential or incidental, including without limitation, any damages for lost profits, stolen goods, or claims by any other party caused by defective products or otherwise arising from the incorrect or otherwise improper installation or use of this product.

This warranty applies only to defects in parts and workmanship relating to normal use. It does not cover:

• damage arising from improper maintenance or negligence

• damage caused by fire, flood, wind or lightning

• vandalism

• fair wear and tear

Ness shall, at its discretion, repair or replace any defective products. Improper use, that is, use for purposes other than those mentioned in this manual will void the warranty. Contact Our authorized dealer, or visit our website for further information regarding this warranty.

Limited warranty

Ness shall not be liable to the purchaser or any other person for damage arising from improper storage, handling or use of this product.

Installation of this Product must be carried out by qualified persons appointed by Ness. Installation of this Product must be carried out in accordance with Our instructions in the product manual.

The information contained in this document is the sole property of Ness. No part may be copied without written authorization from Ness.

Directive compliance

Hereby Ness declares that the SmartLiving series of intrusion-control panels, the Air2 series of devices and the SecureLink / SmartLink product are in compliance with the essential requirements and other relevant provisions of Directive 1999/ 5/CE.

Moreover, Ness also declares that all other devices mentioned in this manual are in compliance with the essential requirements and other relevant provisions of Directive 2004/108/CE.

The full declarations of conformity can be found at URL: www.nesscorporation.com

State-of-the-art installations (DM 37/08)

The devices described in this manual, in accordance with the settings selected during the installation phase and the following illustrated guidelines are, alternatively, in compliance with the the Italian Normative CEI 79- 2:1998+Ab:2000 performance level 2 or European Normative CEI EN 50131- 3:2009 (in reference to Control and indicating equipment - intrusion control panels) and CEI EN 50131-6:2008 (in reference to Power supplies) security grade

In support of research, development, installation, testing, commissioning and maintenance of intrusion alarm systems installed in buildings please refer to the following normative documents:

CEI 79-3 e CEI CLC/TS 50131-7.

When installing Ness products, it is up to the installation company to install systems equipped with Normative CEI 79-2 compliant devices rather than devices compliant with European Normatives series EN50131 within and not over the DOWs summarized in amendment CEI 79-2;V1:2010.

Anti-intrusion control panels

www.nesscorporation.com

National Customer Service Centre Ph: 1300 551 991 customerservice@ness.com.au

Ness Smartliving Installation and Programming Manual

Document Part No: 890-443

All rights reserved. No part of this publication may be reproduced, transmitted or stored in a retrieval system in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of Ness.

Ness reserves the right to make changes to features and specications at any time without prior notication in the interest of ongoing

product development and improvement.

CEI 79-2 EN 50131-3 EN 50131-6 CEB T01

Installation and programming manual

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Limited warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

European Directive compliance. . . . . . . . . . . . . . . . . . . . . . . . 2

State-of-the-art installations (DM 37/08) . . . . . . . . . . . . . . . . 2

Table of contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

About this manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

0-1 Terminology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

0-2 Graphic conventions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Chapter 1 General information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

1-1 Manufacturer's details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

1-2 Description of the product and various models . . . . . . . . . . . . . . . . . 6

1-3 Products certified and conforming to directives . . . . . . . . . . . . . . . . . 6

1-4 Patents Pending. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

1-5 Manuals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

1-6 Operator Qualifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

1-7 Access Levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

1-8 Conventions – Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Table of contents

Chapter 2 The control panel and peripherals . . . . . . . . . . . . . . . . . . . 9

2-1 Environmental Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

2-2 SmartLiving intrusion control panels . . . . . . . . . . . . . . . . . . . . . . . . 9

2-3 Peripherals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

2-4 SmartLAN ethernet interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

2-5 AUXREL32 power distribution board . . . . . . . . . . . . . . . . . . . . . . . . . 22

Chapter 3 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

3-1 Installing the control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

3-2 Connecting peripherals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

3-3 Addressing the peripherals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

3-4 Auto-enrolling peripherals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

3-5 Wiring and balancing alarm detectors. . . . . . . . . . . . . . . . . . . . . . . . 37

3-6 Wiring and balancing rollerblind/shock sensors . . . . . . . . . . . . . . . . . 39

3-7 Connecting wireless detectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

3-8 Learn zone balancing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

3-9 Connecting the outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

3-10 Installing add-on boards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

3-11 IP and Internet Connectivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Chapter 4 First power up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Chapter 5 Installation project via the SmartLeague . . . . . . . . . . . . . . 46

5-1 The SmartLeague software programme . . . . . . . . . . . . . . . . . . . . . . 46

5-2 Using the software programme . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

5-3 Creating a project layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Chapter 6 Options and programming methods . . . . . . . . . . . . . . . . . . 49

6-1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

6-3 Programming via the SmartLeague programme . . . . . . . . . . . . . . . . 50

6-4 Fast programming from the keypad (Wizard) . . . . . . . . . . . . . . . . . . 50

6-5 Panel options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

6-6 Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

6-7 Zones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

6-8 Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

6-9 Walk test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

6-10 Telephone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

6-11 Events . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

6-12 Timer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

6-13 Partitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

6-14 User Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

6-15 Installer codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75

6-16 Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

6-17 Arming scenarios. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

6-18 Shortcuts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78

6-19 Expansions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79

6-20 Keypads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79

6-21 Readers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80

6-22 Sounders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81

6-23 Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81

6-24 Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82

6-25 Default settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82

6-26 User functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84

6-27 Other parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85

6-28 Activating outputs without authentication. . . . . . . . . . . . . . . . . . . . . 88

6-29 Programming the Nexus. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89

Anti-intrusion control panels

Chapter 7 Complacency with the regulations in force . . . . . . . . . . . . . 92

Chapter 8 Errors and faults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95

8-1 Faults detected by the control panel . . . . . . . . . . . . . . . . . . . . . . . . 95

8-2 Communication BUS (I-BUS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96

8-3 LED activity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96

8-4 Ring Sensitivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97

8-5 Calibrating the touch-screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97

Appendix A Technical terminology and Glossary. . . . . . . . . . . . . . . . . . 98

Appendix B Shortcuts at default . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106

Appendix C Available Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107

Appendix D Voice messages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108

Appendix E Screw Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110

Appendix F Combination of outputs triggered

by events . . . . .

. . . . . . . 111

Appendix G SIA Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112

Installation and programming manual

Info

ABOUT THIS MANUAL

DCMIINE0SLIVINGE

5.10

The main supervisory unit or any constituent parts of the SmartLiving intrusion control system.

Directions as seen by the operator when directly in front of the mounted device.

A device which sends voice calls or digital reports to programmed contact numbers in the event of an alarm.

Persons whose training, expertise and knowledge of the products and laws regarding security systems, are able to create, in accordance with the requirements of the purchaser, the most suitable solution for the protected premises.

Click on a specific item on the interface (drop-down menu, options box, graphic object, etc.).

Click on a video button, or push a key on the control-panel keypad.

MANUAL CODE

VERSION

0-1Terminology

CONTROL PANEL, SYSTEM, DEVICE

LEFT, RIGHT, BEHIND, ABOVE, BELOW

DIALER

QUALIFIED PERSONNEL

SELECT

PRESS

Following are the graphic conventions used in this manual.

Conventions Example Description

Text in italics

<text> #<AccountCode> Editable field

[Uppercase letter] or [num-

ber]

BUTTON

The “Note” sections contain important information relating to the text.

The “Attention” prompts indicate that total or partial disregard of the procedure could damage the device or its peripherals.

The “DANGER” warnings indicate that total or partial disregard of the procedure could injure the operator or persons in the vicinity.

See paragraph 0-2 Graphic

conventions

[A] or [1]

, ,

Indicates the title of a chapter, section, paragraph, table or figure in this manual or other

Reference relating to a part of the system or

published reference.

video object.

Keypad keys

0-2Graphic conventions

Note

ATTENTION!

DANGER!

Similarly marked dialogue boxes contain recommendations and/or guidelines which the manufacturer wishes to call attention to.

About this manual 5

GENERAL INFORMATION

Chapter 1

1-1Supplier's details

Supplier: Nes

Address: 4/167 Prospect Hwy,

Seven Hills, NSW, 2147 Australia

Tel: +61 2 8825 9222

e-mail: customerservice@

Web: www.nesscorporation.com

The persons authorized by the manufacturer to repair or replace the parts of this system, hold authorization to work on Ness Corporation’s brand devices only.

s Corporation

ness.com.au

various models

Description: Intrusion control panel

Models: SmartLiving 505

SmartLiving 515

SmartLiving 1050

SmartLiving 10100

Applied Normative: CEI 79-2:1998+Ab:2000, CEI EN 50131-3:2009 and CEI EN

50131-6:2008

Certification agency: IMQ - Security systems

Security rating: 2

1-2Description of the product and

1-3Products certified and

conforming to directives

The SmartLiving intrusion control panel and the devices described in this manual have been certified by the IMQ - Security Systems agency as compliant with CEI 792:1998+Ab:2000, CEI EN 50131-3:2009 and CEI EN 50131-6:2008, when duly programmed, as described in Chapter 7 - Compliancy with the regulations in force.

The Control panel enclosure houses the following certified devices:

• INIM switching-power supply

• Motherboard (IN082 or IN088)

• SmartLogos30M voice board (accessory item)

• FLEX5/U input/output expansion board (accessory item)

• AUXREL32 relay board (accessory item)

• SmartLAN/SI and SmartLAN/G LAN interface boards (accessory items)

• IB100/RU BUS isolator board (accessory item)

• ProbeTH thermal-probe kit for battery-charge optimization (accessory item)

• TamperNO tamper-protection kit (accessory item)

• Backup battery, 12 V @ 17 Ah

• Motherboard (IN082 and IN088) integrated Type B notification apparatus

The control panel complacency is also guaranteed when connected to the following certified devices:

6 General information

Installation and programming manual

• FLEX5/P input/output expansion boards

• Joy/MAX, Joy/GR, cCode/G, nCode/G keypads

• nBy/S outdoor-mount proximity readers

• nBy/X universal-mount proximity readers

• IB100/RP BUS isolator

• Self-powered IB100/A BUS isolator

• nCard access-control card for proximity readers

• Tag for nKey or nBoss proximity readers

• Self-powered sounderflashers for outdoor installation: Ivy, Ivy-F, Ivy-M, Ivy-FM, IvyB, Ivy-BF, Ivy-BM, Ivy-BFM

• Wireless devices AIR2, AIR2-BS100 (transceivers), Air2-IR100 (PIR detectors), Air2MC100 (magnetic contacts)

ATS2 notification apparatus (refer to EN50131-1:2008-02, paragraph 8.6 Notification, Table 10, page 46, Grade 2 and EN50136) characterized by:

• Transmission time - classification D2 (60 seconds)

• Transmission time - max. values M2 (120 seconds)

• Classification time - classification T2 (25 hours)

• S0 Substitution security (no detection of device substitution)

• I0 Information security (no detection of message substitution)

ATS4 notification apparatus (refer to EN50131-1:2008-02, paragraph 8.6 Notification, Table 10, page 46, Grade 3 and EN50136) features the following parameters (available on SmartLAN/G and SmartLAN/SI only):

• Transmission time - classification D2 (60 seconds)

• Transmission time - max. values M2 (120 seconds)

• Classification time - classification T3 (300 minutes)

• S1 Substitution security (measures aimed at detecting the substitution of the transceiver of the supervised site by means of an identifier code or address in all messages sent over the transmission link).

• I2 Information security (measures aimed at impeding unauthorized changes to transmitted information).

The SmartLiving series of control panels employs the following patented technologies.

put/Output Terminals: each terminal on-board the control panel, keypads and

• In expansion boards can be configured as either an input or output zone.

• nBy/X proximity reader: this reader has been especially designed to flush-mount to all models of electrical light-switch backboxes.

• Learn zone balancing: this option allows the control panel to save the balancing values of all the system zones automatically, thus eliminating the task of typing them in.

TYPE B NOTIFICATION APPARATUS

1-4Patents Pending

1-5Manuals

Installation and

programming manual

(this manual)

This manual (not included in the package) can be purchased from your retailer. You (the installer) should read carefully through it in order to become familiar with all the components and operating procedures of the SmartLiving system.

In order to provide adequate protection, the installer must adhere to all the manufacturer's guidelines relating to the active and passive security devices of this system.

Installation and

programming guide

This guide is included in the control panel package and provides all the instructions and illustrations necessary for fast installation and programming of the SmartLiving system. It provides step by step descriptions of the procedures required for the system wiring,

General information 7

1-5-1

1-5-2

the various connections and first power-up. It also provides a table for the peripheral addressing process and a quick guide indicating default parameters and values and how to programme/change them directly from the keypad.

User's manual

The installer should read carefully through the user's manual (supplied with each control panel). Once the system has been installed, you must ensure that the User's Manual is available to the users for consultation, and that they fully understand how the system works and are aware of all the functions, settings and procedures.

It is the installer's responsibility to inform the system users that, regardless of its capabilities, an intrusion alarm system is not a substitute for the necessary precautions building occupants must take to prevent intrusion.

Installer

The installer is the person (or group of persons) who sets up and programs the entire security system in accordance with the purchaser's requirements and in respect of the safety and security regulation in force. As the only individual in contact with system users, it is the installer's responsibility to instruct them on how to use the security system properly.

Under normal circumstances, the installer is not allowed to arm/disarm the system without previous authorization from the user. All the system partitions must be disarmed before accessing the parameter programming phase.

The access code of the installer is a level 3 access code.

User

The users are the occupants of the building where this intrusion control panel is installed. Only authorized users can access and operate the system.

Thanks to the extreme flexibility of the system, the most common operations can be carried out without authorization. This operating method must be expressly requested by the main user, as it considerably lowers the security level of the system and may cause false alarms, accidental arm/disarm operations, etc.

A system access code can be associated with each user. The programming process allows you to define the code hierarchy:

• User

• Manager

• Master The system codes can carry out, in accordance with their assigned level in the system hierarchy (the "User" being the lowest level), the following operations on all other codes that are inferior hierarchically:

•• enable/disable

•• change PIN

•• change the programming parameters

If the system programming complies with security grade 3 of EN 50131, some partition arming or delete memory operations, requested from a keypad, may be authorized by the entry of a level 3 code (installer code) as well as by a user code.

1-5-3

1-6Operator Qualifications

1-6-1

1-6-2

1-7Access Levels

The normative defines the following system-access levels, regardless of system-access

itations:

lim

• Level 1 - access by any person (e.g. passer-by)

• Level 2 - user access

• Level 3 - installer or maintenance operator access (authorized by user - level 2)

• Level 4 - manufacturer access

1-8Conventions – Glossary

In order to understand the terminology used in this manual and improve your knowledge of this system and its operating procedures, read carefully through the glossary (refer to Appendix A, Technical terminology and Glossary).The appendix contains the definitions of technical terms commonly used in the field of security, therefore, relevant to the SmartLiving system.

8 General information

Installation and programming manual

THE CONTROL PANEL

AND PERIPHERALS

All control panels from the SmartLiving series are for indoor installation only and

erate best under the following conditions:

• Temperature: from -10° to +40°C

• Maximum humidity:75% (without condensation)

• Environmental class:II

The nCode/G, cCode/G, Alien/S, Alien/G, IB100, FLEX5, Nexus and nBy/X peripheral devices are for indoor installation only and operate best under the following environmental conditions:

• Temperature: from -10° to +40°C

• Maximum humidity:75% (without condensation)

• Environmental class:II

The nBy/S reader is suitable for outdoor installation and operates best under the following conditions:

• Temperature: from -25° to +70°C

• Maximum humidity:93% (without condensation)

• Protection grade:IP34

• Environmental class:IV

Chapter 2

2-1Environmental Conditions

ntrol panels

Package contents

Inside the package you will find:

• Metal enclosure containing the wired motherboard and power supply (adapter or switching-power supply)

• User's Manual

• Quick Installation Guide

• Plastic bag:

Table 1:

Control panel models

3k9 Ohm 1/4W resistance

Resistance 6k8 Ohm 1/4W

Backup-battery wire

Screws to secure the frontplate of

the metal enclosure

Items not included in the package:

Thermal probe (battery-charge optimizer which operates in accordance with the battery temperature), backup battery, Dialler Lead, SmartLeague programme CD, Installation Manual. These devices are accessory items which must be purchased separately.

Package contents

505 515 1050 1050L 10100L

10 20

2-2SmartLiving intrusion

2-2-1

The control panel and peripherals 9

Control panel descriptions

2-2-2

Table 2:

Control panel models

Power supply voltage

Nominal output voltage

Voltage - operating range

Maximum current draw

Current draw of control panel

motherboard

Maximum distributable current @ 12V

Maximum distributable current to

open-collector outputs

Maximum power-supply voltage ripple

Max. battery-charge current

Backup battery

Max. current across +AUX terminals

Power supply (EN 50131)

Enclosure Dimensions (W x H x D)

Weight (without battery)

Control panels - electrical and mechanical features

505 515 1050 1050L 10100L

230V ~ -15% +10% 50/60Hz

13.8V

9 - 16 V

0.2A 0.4A 0.6A

110mA @ 22V

1.2A 3A 5A

150mA 500mA

340mV 70mV

900mA

2.5 Kg 2.2 Kg 5.3 Kg

1A 2A

12V 7Ah 12V 17Ah

recharged 80% in 24h

(1.35A for +AUX1, 1.35A for +AUX2, 1.35A for +AUX3)

Type A

21.5 x 30.5 x 8.5cm 37.5 x 51 x 8.5cm

Compliancy with EN 50131, CEI 79 or CEB T014 requires that the values of the

mum distributable current respect determined limits, as indicated in paragraph 3-

maxi 1-3 Maximum current - normative references.

The control panel label s located inside the enclosure.

The following table shows the maximum number of devices supported by the various control panel models.

75mA @ 13.8V=

4.05A

Terminals on

panel

Outputs on

control-panel

motherboard

(JOY, nCode/G, cCode/G, Alien)

Possible key combinations

Table 3:

Control panel models

Total terminals

total

configurable as inputs

configurable as rollerblind/shock

configurable as outputs

Total zones

total

Relay

open-collector

Partitions

Keypads

Voice memo slots

FLEX5 expansions

nBy Readers

Air2-BS100 Transceivers

Digital keys and keyfobs

IB100 isolators

Nexus dialer

Codes

Scenarios

Timer

Recordable Events

Programmable events

Control panel - Main Features

505 515 1050 1050L 10100L

5 15 50 100

5 10

0 5

10 30 100 200

5 10 15

5 10 20 40

10 20 30

50 100 150

4294967296

30 50 100

10 20

500 1000

10 30 50

SmartLiving control panels are not equipped with built-in dislodgement-tamper microswitches.

Note

For the order code of this accessory item, refer to Ness Sales staff.

10 The control panel and peripherals

Installation and programming manual

SmartLiving 505/515

control-panel motherboard

SmartLiving1050/1050L/10100L

Control panel motherboard

5.xx

Table 4:

Control panels - description of parts

Models 505 515 1050 1050L 10100L

2-3

4-5 PSTN

6-7-8-9 + D S -

10-11-12 NO NC COM

13 +AUX

14-15 OC1 OC2

16 +AUX

17-19-21-

23-25

18-20-22-

24-26

27 +AUX

28-29 AC

28-30-32-

34-36

29-31-33-

37 +AUX

Power adapter (Transformer) 3A switching power supply

Mains connection terminal-board (230 Vac) - 50/60 Hz

Power cable - adapter to control

panel

Power cable - switching-power supply to panel

Mains cable entry

Metal enclosure

Anchor-screw locations for the metal backbox

Dislodgement-tamper microswitch location

Backup battery

Backup-battery wire

Backup-battery connector

Thermal probe (accessory item)

Thermal probe connector

Thermal probe (enable/disable)

jumper

Connectors for the SmartLAN power-supply jumper

Local I-BUS connector

Maintenance jumper connectors

SmartLogos30M voice-board connector

Control panel to PC serial cable connector

Dislodgement-tamper microswitch connector (accessory item)

Open-panel tamper microswitch connector (accessory item)

Open-panel tamper microswitch

Terminal board

Blue and yellow activity LEDs

Firmware version label

Anchor-screw locations for AUXREL32 board

Ground connection screws

FLEX5/U expansion board locations

icon/identi-

fier

Table 5:

Control panel - terminal board

Model

505 515 1050 1050L 10100L

Earth connection

Internal telephone-line connection

Land-line connection (PSTN)

Voltage-free contacts of the relay output (Typically External Siren)

I-BUS connections

12V Ancillary power supply

Open-collector outputs (Typically OC1 Strobe & OC2 Internal Siren)

+12V Ancillary power supply

Power supply negative (earth or GND)

T1-T2-T3-

T4-T5

Control panel input terminals: T1, T2, T3, T4 and T5

12V Ancillary power supply

Power supply input from

T6-T7-T8-

T9-T10

the transformer

Terminals: T6, T7, T8, T9 and T10 of the

Power supply negative (earth or GND)

12V Ancillary power supply

control panel

5A switching

power supply

The control panel and peripherals 11

SmartLiving 10100L

SmartLiving 505/515 SmartLiving 1050

12 The control panel and peripherals

Installation and programming manual

JOY keypad board

JOY keypad backbox

Events log memory

The control panel events are saved to a non-volatile semiconductor-memory which retains data without the need of power.

The electrical characteristics of semiconductor devices diminish over time. However, a minimum period of 40 years data retention is guaranteed.

I-BUS interconnections

SmartLiving control panels are equipped with a 4-wire BUS for peripheral interconnections (2 power-supply wire and 2 data exchange wires, refer to paragraph 3-2-1 The I-BUS line wiring).

The intellectual property rights regarding the electrical, structural and protocol features of the BUS are the sole property of the manufacturers.

The I-BUS is not a RS485 differential BUS.

The control panel I-BUS accommodates the following peripherals:

OY/GR, JOY/MAX, nCode/G, cCode/G, Alien/G e Alien/S keypads

• J

• Readers (nBy/S and nBy/X)

• Expansions (Flex5)

• Transceivers (Air2-BS100)

• Sounderflashers (Ivy)

• IB100 isolators

• GSM dialer (Nexus)

2-2-3

2-2-4

2-3Peripherals

Terminals configurable as OC outputs

Maximum current draw per terminal

Dimensions (W x H x D) [mm]

Joy/GR and Joy/MAX keypads

Table 6:

Joy keypads models JOY/GR JOY/MAX

Voltage [V]

Typical current draw [mA]

[mA]

Weight [g]

Table 7:

Dislodgement-tamper microswitch screw location

Dislodgement-tamper microswitch spring

Device specifications

70 90

142 x 116 x 20

160 180

Joy - description of parts

Terminal board

Buzzer

Microphone (Joy/MAX only)

Temperature sensor (Joy/MAX only)

Open-tamper microswitch

Backlit graphic display

Signaling LEDs

Antenna (Joy/MAX only)

Speaker-wire connector (Joy/MAX only)

Wire entry

Wall-mount screw locations

Speaker housing

Board supports

9 - 16

150

2-3-1

The control panel and peripherals 13

Keypad terminals:

nCode/G keypad

cCode/G keypad

F F

Retro keypads

nCode/G and cCode/G

Table 8:

n. icon/identifier description

1 +

2 D

3 S

4 -

5 T1

7 T2

Joy - terminal board

Terminal “+” for the I-BUS connection

Terminal “D” for the I-BUS connection

Terminal “S” for the I-BUS connection

Terminal “-” for the I-BUS connection

Screw terminal of keypad terminal T1

Negative power terminal (Negative or GND)

Screw terminal of keypad terminal T2

Negative power terminal (Negative or GND)

Terminals T1 and T2 can be configured as:

• Input (also as Rollerblind or Shock)

• Output

• Double zone

• Supervised Output

The keypad package contains a sticker (to be located under the keypad flip) which can be used to note down the keypad address or label, its location, the partitions it controls and any phone-contact numbers.

nCode/G and cCode/G Keypads

Table 9:

Keypad models nCode/G cCode/G

Voltage [V]

Typical current draw [mA]

Terminals configurable as OC

Maximum current draw per

Dimensions (W x H x D) [mm]

outputs

terminal [mA]

Weight [g]

Device specifications

70 80

87 x 129 x 18

135 155

9 - 16

150

2-3-2

Table 10:

nCode/G and cCode/G -

description of parts

Backlit graphic display

Signaling LEDs

Cable connector

Tamper microswitch

Screw location

Terminal board guide

Buzzer

nCode/G and cCode/G keypads are equipped with a buzzer and a T1 terminal which can be configure

• Input (also as Rollerblind or Shock)

• Output

d as:

• Double zone

14 The control panel and peripherals

Installation and programming manual

6 wire cable KB100 - terminal board

Mounting bracket

M M

KB100 - deep mounting bracket

M M

Alien/S - front

Alien/S - back

Alien/S - mounting bracket

F F

You can connect nCode/G and cCode/G keypads using the connector on the back of the device, using either the 6 wire cable (included), or the KB100 terminal board included in the deep-bracket kit (accessory kit).

Table 11:

1 Red +

2 Yellow D

3 Green S

4 Black -

5 Blue T1

6 Black

Wire

colour

Connection cables - KB100 terminal board

KB100 ter-

minal board

Table 12:

Wire/Terminal “+” for the I-BUS connection

Wire/Terminal “D” for the I-BUS connection

Wire/Terminal “S” for the I-BUS connection

Wire/Terminal “-” for the I-BUS connection

Wire/terminal of keypad terminal T1

Negative power wire/terminal (Negative or GND)

Brackets - description of parts

Wire entry

Wall-mount screw locations

Flush-mount screw locations

Backlocking grips

description

Note: Keypads are enabled with Tamper switches, so ensure they are securely mounted before attempting to operate the system.

Alien/G and Alien/S

2-3-3

touch screen keypads

• Touch-screen

• Protection against removal and dislodgement tamper

• Input/Output terminals (Alien/G only)

• Compatible with all SmartLiving 5.0 and higher models

• Thermometer and chronothermostat function

• Microphone and loudspeaker for voice functions

• Built-in proximity reader

• System interface with I-BUS and RS485 BUS

• USB Interface

• SD card interface

• Photoframe function with images on SD card

• Background customization with images on SD Card

• Skin selection

• Black or white

The control panel and peripherals 15

Table 13:

Alien - description of parts

Display

Microphone

Proximity reader

Touch pen holder

Closure hooks

Backlocking grips

Securing screw

Alien/G open

Alien/G - front

Alien/G - back

Alien/G - PCB

1 2 3 4 5 6 7 8 9 10 11 12 13 14

10 -

11 T1

13 T2

12 - 14

Table 13:

Selection jumper connectors for EOL resistance on

1 + 14V

2 - 14V

3 +

4 D

5 S

6 -

7 +

8 B

9 A

Alien - description of parts

Cable entry

Screw locations

Back-locking grip locations

Flush-mount screw locations for “503” box

PCB

Terminal board/Connector for wires

Dislodgement-tamper microswitch

Open-tamper microswitch

Battery connector

Ethernet connector

Mini USB connector

Slot for micro-SD card

RS485

LED activity

Temperature sensor

Reset button

Forced calibration button

Table 14:

icon/iden-

tifier

Alien/G - terminal board

description

Positive power terminal

Negative power terminal

Terminal “+” for the I-BUS connection

Terminal “D” for the I-BUS connection

Terminal “S” for the I-BUS connection

Terminal “-” for the I-BUS connection

Terminal “+” for the RS485 BUS connection

Terminal “B” for the RS485 BUS connection

Terminal “A” for the RS485 BUS connection

Terminal “-” for the RS485 BUS connection

Screw terminal of keypad terminal T1

Screw terminal of keypad terminal T2

Negative power terminal (Negative or GND)

Terminals T1 and T2 can be configured as:

• Input (also as Rollerblind or Shock)

• Output

• Double zone

• Supervised Output

16 The control panel and peripherals

Installation and programming manual

Alien/S - 8 wire cable

nBy/S

1 2 3 4

nBy/X

1 2 3 4

Patent Patent

Connection of the Alien/S keypad is achieved through the connector on the back and must done using the 8 wire cable which comes with the keypad.

le 15:

Wire

colour

Red +

Yellow D

Green S

Black -

Grey B

Blue A

White REOL

Alien/S

terminal

board

Tab

Alien/S - Connection wires

description

Cable/Terminal “+” of the I-BUS and RS485 BUS

Cable/Terminal “D” for the I-BUS connection

Cable/Terminal “S” for the I-BUS connection

Cable/Terminal “-” of the I-BUS and RS485 BUS

Terminal “B” for the RS485 BUS connection

Terminal “A” for the RS485 BUS connection

Wire/Terminals to establish the EOL on the RS485

Keypad models Alien/S Alien/G

Voltage [V]

Typical current draw [mA]

Terminals configurable as

Maximum current draw per

Number of display colours

Reader terminals:

OC outputs

terminal [mA]

Input/Output terminals

Screen dimensions[in]

Display resolution

SD card capacity [GB]

Box for flush-mount

installation

Dimensions (W x H x D)

[mm]

Weight [g]

Dimensions (W x H x D) [mm]

1 +

2 D

3 S

4 -

Table 16:

Device specifications

150 400

- 2

4.3 7

480x272 800x480

Max. 16

Bracket for mounting to stan-

dard “503” boxes

131x81x17

160 520

9 - 16

150

65000

Flush-mount box supplied

(214x129x54 mm)

219x143x34

If mounted to flush-mount

box: 219x143x17

Readers - nBy/S and nBy/X

Table 17:

Reader models nBy/S nBy/X

Voltage [V]

Typical current draw [mA]

Weight [g]

Table 18:

Optical sensors for open-enclosure and dislodgement tamper detection

Table 19:

icon/identi-

fier

Device specifications

9 - 16

40 35

64 x 80 x 17 19 x 50 x 51

45 25

nBy - description of parts

Terminal board

Buzzer (nBy/S only)

LED

Antenna

nBy - terminal board

description

Terminal “+” for the I-BUS connection

Terminal “D” for the I-BUS connection

Terminal “S” for the I-BUS connection

Terminal “-” for the I-BUS connection

The control panel and peripherals 17

Flex5 expansion boards

Flex5/U

B C E F

D G

2-3-4

• Flex5/U c

omes in an enclosure with on-view terminals and address DIP-Switch, as shown above. It is evident that this version offers little protection to the terminals and is recommended to be installed in a tamper protected enclosure. The jumper of connector [D] enables/disables the protection against open and dislodgement tamper of the plastic enclosure only.

Table 20:

Expansion board models FLEX5/U

Voltage [V]

Typical current draw [mA]

Max. current across +AUX terminals

[mA @13.8V]

Dimensions including enclosure

(W x H x D) [mm]

Weight including enclosure [g]

Device specifications

9 - 16

300

105 x 58 x 18

The packages of both versions of the Flex5 expansion board contain:

• Flex5 expansion board in a plastic enclosure

• Dislodgement/Open tamper jumper

• 10 resistors @ 3K9Ohm 1/4W

• 10 resistors @ 6K8Ohm 1/4W

Table 21:

DIP-Switch strip for peripheral device addressing

Connector to enable peripheral-tamper detection

Flex5 - description of parts

Terminal board

Buzzer

Dislodgement-tamper microswitch

Open-tamper microswitch

Peripheral activity LED (where present)

Peripheral activity LED signals are as follows:

• fast blinking - peripheral operative and enrolled (in configuration)

• slow blinking - peripheral operative but not enrolled (not in configuration)

The Flex5 expansion board terminals are as follows:

Table 22:

1-2-3-4 + D S -

18 The control panel and peripherals

5-6 +AUX

7-9-11-

13-15

8-10-12-

14-16

icon/

identifier

T1-T2-T3-

T4-T5

Expansion terminal board

description

I-BUS connection terminals

12V ancillary power source terminals

Screw terminals for expansion terminals: T1, T2, T3, T4

and T5

Negative power terminals (Negative or GND)

Installation and programming manual

Terminals T1, T2, T3, T4 and T5 can be configured as:

• Input (Rollerblind or Shock for terminals T1, T2, T3 and T4 only)

• Output

• Double zone

• Supervised Output

Transceiver for Air2-BS100

The Air2-BS100 two-way wireless system integrates directly with all models of the Ness SmartLiving Series intrusion control panel range.

Description of the Air2 system devices:

• Air2–BS100 transceiver module

• Air2–IR100 passive infrared detector

• Air2–MC100 magnetic contact/rollerblind/exit

• Air2–MC200 magnetic contact/shock and tilt detector

• Air2–KF100 4 button remote-control keyfob

• Air2-FD100 smoke detector

For a complete description of all these devices refer to the Air2-BS100 Installation Guide.

IVY sounder/flasher

The IVY is a High Security Outdoor Siren / Flasher. The self-powered sounders from the IVY outdoor series are controlled continuously by a microprocessor which monitors all the device parameters to ensure performance and reliability at all times.

For a complete description of all these devices refer to the sounder Installation Guide.

IB100 isolators

Isolators from the IB100 series peripherals can be connected directly to the I-BUS, in order to increase both its length and performance.

Each isolator has 4 input terminals and 4 output terminals for the BUS connection with the following functions:

• Galvanic Isolation, up to 2500V, for the entire BUS between input and output.

• Regeneration of the communication signals.

• Detection of anomalies towards the output section and its consequent isolation.

For a complete description of all these devices refer to the respective Installation Guide.

2-3-5

2-3-6

2-3-7

Nexus dialers

All models of the Nexus dialer are managed by the BUS. The Standard model interfaces SmartLiving control panels with GSM communication channels whereas, the Nexus/G model also interfaces with GPRS channels.

The functions made available to control panels equipped with this device are:

• voice calls via the Nexus using an installed SmartLogos30M voice board

• digital report calls via GSM using CONTACT-ID and ADEMCO 10 bps protocols

• digital report calls via GPRS using SIA-IP (Nexus/G model only)

• SMS messages for each event using either -

•• the description provided by the keypad events log

•• the customized description (maximum 50 editable SMS texts)

• the control panel carries out commands sent by the user via SMS message

• the control panel carries out commands after recognition of the user's telephone number (CALLER-ID)

• Answerphone

Table 23:

Dimensions including enclosure (W x H x D)

Nexus - electrical and mechanical features

Voltage [V]

Current draw in standby [mA]

Maximum current draw [mA]

[mm]

Weight including enclosure [g]

9 - 16

900

105 x 58 x 18

2-3-8

The control panel and peripherals 19

The Nexus package includes:

H L M

C D

• Nexus expansion board in a plastic enclosure

• Remote antenna with 3 meters of cable

Table 24:

Nexus - description of parts

Terminal board

Antenna connector

P1 button

P2 button

SIM card housing (SIM non included)

Buzzer

Open-tamper microswitch

Communication LED (green)

Emergency LED (red)

Fault LED (red)

Connection LED (green)

The terminals for the BUS connection are as follows:

1 +

2 D

3 S

4 -

icon/

identifier

Table 25:

Nexus terminal board

description

Terminal “+” for the I-BUS connection

Terminal “D” for the I-BUS connection

Terminal “S” for the I-BUS connection

Terminal “-” for the I-BUS connection

Peripheral activity LED signals are as follows:

Table 26:

LED Function ON OFF

Communication

Emergency

Faults

Connection

Indicates communica-

tion with the control

panel

Indicates communica-

tion failure with the

control panel

Indicates the presence

of faults

Indicates the status of

the GSM network

Nexus LEDs

The LED blinks during ongo-

ing communications

Blinks in the event of tam-

per or fault on the BUS

Blinks in the event of ongo-

• Slow blinking -

• Fast blinking - Provider

ing faults

Searching for the provider

found

Not communicating

Normal communication with

the control panel

No faults present

Device Off

After activation of the Fault LED (indicating a fault is present), you can obtain further information regarding the cause of the fault by simply pressing button P2 [D]. The successive activation of the Emergency and Fault signaling LEDs will signal as follows:

Table 27:

LED On Fault

Communication

Emergency

Faults

You can obtain an indication of the GSM reception level by simply pressing button P1 [C] and observing the number of LEDs which light amongst the Communication,

Fault signaling

No Credit

SIM card with PIN request

Communication problems

enabled

with the GSM module

Emergency and the Fault LEDs (viewing lasts 5 seconds):

• 1 LED - weak reception

• 2 LED - good reception

• 3 LED - excellent reception

20 The control panel and peripherals

Installation and programming manual

E F

G O

SmartLAN/G

SmartLAN/SI

SmartLAN boards (SmartLAN/G and SmartLAN/SI versions) allow the expansion of connectivity of all Ness SmartLiving control panels to the LAN and the Internet.

The operating capacity of the SmartLAN board depends on the proper configuration of the networks it is connected to. Therefore, if you are installing a SmartLAN board, it is necessary to contact the network administrator in order to configure it correctly.

Both boards allow you to programme the control panel parameters via the LAN through the SmartLeague software programme.

The SmartLAN/G also allows users to:

• send event-report e-mails and attachments.

• interact, after user authentication, with the control panel through any browser (Explorer, Firefox, Opera, Safari, etc.), providing it has an integrated web-server:

•• view the status of zones

•• view the status of partitions

•• view the status of timers

•• view the events log

•• access one of the keypads operating within the system which will provide the

user with an interface that is recognized by the control panel

Thus the user will be able to arm/disarm partitions, bypass/unbypass zones, activate/ deactivate the alarm and tamper memories.

For a more detailed explanation of how to use the Web-server, refer to the User Manual of the control panel in use.

2-4SmartLAN ethernet interface

Table 28:

Expansion board models SmartLAN/SI SmartLAN/G

Power supply voltage

Maximum current draw

Operating temperature

Dimensions

Maximum capacity of the µSD-

card

Security protocol

PCB code

Table 29:

Ancillary power connector (SmartLiving515 only)

LED - Control panel to SmartLAN connection

LED - transmission/reception over BUS RS232

Device specifications

12 V

70 mA 90 mA

-5 / +40 °C

81 x 54 x 25 mm

8-bit proprietary

encryption

IN074 IN133

SmartLAN - description of parts

RJ45 LAN line jack

DB9 serial line jack (on the back)

µSD-card connector

LED - Connection speed at 100Mbps

RESET button

HARD RESET button

LED - Board power

LED - Network connection

LED - Network activity

LED - Network collision

Fixing hole and earthing

SD-card (not included)

32 Gb

128-bit AES

The control panel and peripherals 21

distribution board

The AUXREL32 power distribution board (accessory item) can be used with SmartLiving 1050L and 10100L models. It provides two relays and allows the system to take full advantage of the current supplied by the switching power supply of the control panel.

Each relay, has a voltage-free contact identified by terminals C1-NO1-NC1 and C2-NO2NC2. The relays are activated by the OC1 and OC2 outputs on the control panel. The activation of each relay is signaled by the on-board LED ([D] for relay 1 and [E] for relay

2).

The 3 pairs of terminals are available, each protected by a resettable fuse (GND/AUX1 – GND/AUX2 – GND/AUX3), and each capable providing 12V@1A.

2-5AUXREL32 power

Table 30:

Power supply voltage

Maximum current

Operating temperature

Dimensions

Table 31:

Table 32:

n. icon/identifier description

1-2-3 C1-NO1-NC1

4-5-6 C2-NO2-NC2

7-9-11 AUX1-AUX2-AUX3

8-10-12

Device specifications

AUXREL32 - description of parts

Terminal board

12V connector

OC1/OC2 connector

Relay LED 1

Relay LED 2

12V present LED

Screw locations

OC1/OC2 connection wire (included)

12V power wire (included)

AUXREL32 terminal board

Free voltage relay 1

Free voltage relay 2

12V@1A screw terminals

Negative power terminals

(Negative or GND)

12 V

3 A

-5°C / +40°C

42 x 78 x 20 mm

22 The control panel and peripherals

Installation and programming manual

Chapter 3

INSTALLATION

3-1Installing the control panel

Wall-mounting

The control panel should be located in a secure location that can be accessed by authorized building occupants only.

1. Using the backbox (Table 4: Control panels - description of parts, G), mark the anchor screw locations on the wall. Be sure not to drill in the vicinity of electrical wiring or plumbing/gas pipes, etc.

2. Insert the screw anchors (recommended size 6mm).

3. Pull the wires through the wire entry.

4. Using the screws, attach the backbox to the wall.

5. Fit the dislodgement-tamper microswitch (provided with SmartLiving 10100L, optional for SmartLiving 505, 515 and 1050, refer to Appen- dix H, Order codes, TamperNO).

5.1. Insert the dislodgement-tamper bracket [A] into its location on

the backbox of the control panel (Table 4: Control panels - description of parts, H).

5.2. Using screw location [B], screw the bracket to the wall.

5.3. Connect the wire coming from the dislodgement-tamper

microswitch [C] to the connector [D] on the board (Table 4: Control panels - description of parts, T).

The cable gland must be flame class rating V-1 or higher.

Connecting the Mains power

supply

The control panel must be powered through a separate line coming from the Mains box. The line must be protected by a safety-standards compliant circuit breaker (trip switch).

The circuit breaker (trip switch) must be located externally to the apparatus and should be easily accessible. The distance between contacts must be at least 3mm. The manufacturer strongly advises the use of a magnetothermic switch with C intervention curve and nominal (maximum) current - 16A.

The protective earthing system must be compliant with all safety standards and laws in force.

3-1-1

Note

3-1-2

Ensure that the Mains is switched Off during the mains connection phase. Danger of electric shock.

The 505 and 515 models

The 505 and 515 models are powered by an external AC power pack.

The 1050 and 10100L models

Pull the cable through the cable entry [E], then connect the mains power to the power-

pply terminal board [D], located on the backplate above the motherboard. When

su connecting the earth wire, follow the indications on the power-supply label [F]. The power-supply provides power to the system and supplies the charge voltage.

Installation 23

DANGER!

Maximum current - normative

230V ~ 50/60 Hz

nput

230V ~ 50/60 Hz

AC I

nput

SmartLiving10100LSmartLiving 1050

Faults

Low battery

references

Compliance with EN50131, CEI 79 or CEB T014 requires full observation of the rules (relating to the applicable normative and the model of the control panel concerned) presented in the Table below.

The system must be arranged in such a way that the current draw under normal circumstances does not exceed the maximum current allowed and the power source for the battery charge is always available.

EN50131-3

CEI 79-2

CEB T014

Table 33:

Norm

Maximum current

Current reserved for

the battery charge

Maximum current per-

Current reserved for

the battery charge

Maximum current per-

Current reserved for

the battery charge

Maximum current permitted

SmartLiving intrusion control panels

505 515 1050 10100L

permitted

mitted

1.2A 1.2A 2.6A 3.5A

1A 1A 2A 2A

1.2A 1.2A 2.6A 3.5A

1A 1A 2A 2A

1.2A 1.2A 2.3A 2.7A

1A 1A 2A 2A

3-1-3

Connecting the backup battery

The backup battery [A] connection must be completed during the phase described in Chapter 4 - First power up.

The SmartLiving 505, 515 and 1050 control panels house one lead battery @12V 7Ah.

The SmartLiving 10100L house two lead batteries, one @12V 17Ah (Max) and the other @12V 1.2Ah.

The battery casing must have HB flame rating or higher.

Using the battery wire [B] (included), connect the battery directly to the control panel motherboard.

Ensure that battery polarity is correct:

- black wire = negative

- red wire = positive

The backup battery is the secondary power source which powers the system during mains failure (230Vac, 50Hz).

Once powered up, the panel will charge and monitor the battery automatically. The panel tests the efficiency of the battery by simulating load current demand at regular 4 minute intervals. If the control panel detects a voltage inferior to 10.4V (battery inefficient), it will generate a Low battery event that will not clear until the voltage goes back to over 11.4V.

This fault will be signalled on the yellow LED on the keypads. To view the fault event, work through the following steps:

Access User menu

, then View , Faults Ongoing .

3-1-4

Note

ATTENTION!

24 Installation

Installation and programming manual

SmartLiving 505/515 SmartLiving 1050 SmartLiving10100L

3A switching power supply

5A switching power supply

12,75

13,25

13,5

13,75

14,25

14,5

0 5 10 15 20 25 30 35 40 45 50

°C

Volt

Thermal probe

3-1-5

The battery charge process can be optimized by means of a thermal probe [C] (accessory item). This device regulates the charging process in accordance with the battery temperature. The thermal probe protects against battery overheating and consequent permanent damage to the battery.

To connect a thermal probe, work through the following steps.

1. Disconnect the battery (if necessary).

2. Connect the thermal probe to the connector on the board [D]. If you are installing a model which is equipped with a switching power supply (SmartLiving 1050, and 10100L), you can connect the thermal probe directly to the power supply connector.

3. If you are installing a SmartLiving505 or 515 model, remove the jumper on the motherboard to enable the thermal probe (refer to Table 4: Control panels - description of parts, N).

4. Using adhesive-insulating tape, attach the thermal probe to the battery [E], in such way as to provide optimized heat-transfer measurements.

5. Hold a thermometer against the probe, and measure the probe temperature.

6. Using the following graph, find the value the measurement will be based on.

7. Using a tester, measure the voltage on the +AUX terminals and adjust the trim-

Installation 25

mer [F] to the previously measured value.

Opening and closing the control panel

SecureLink

Control

panel

Gas

Arrestor

If you wish to remove the metal front plate, work carefully through the following steps.

1. Type-in the installer code on the keypad and press . Access to the installer menu inhibits the activation of the output and any report calls associated with the

“Open-panel” event.

2. Remove the four screws and the metal-frontplate.

3. Insert the Maintenance jumper (refer to paragraph 3-1-10 Maintenance status) and carry out the necessary work.

Once your task is complete, work carefully through the following steps. Remove the Maintenance jumper., Using the 4 screws, secure the frontplate to the backbox. Exit the Installer menu.

If you exit the Installer menu before replacing the panel frontplate, the system panel will not generate an open-panel event. However, the system will generate an open-panel event, if the frontplate is not replaced within 15 seconds of closing the open-tamper switch.

3-1-6

Note

Land-line connection (PSTN)

Terminals 4 and 5 on the control panel motherboard (Table 5: Control panel - terminal board, 4-5) are for the land-line telephone connection.

In order to protect the control panel against the discharge of atmospheric electricity, (lightning), the manufacture strongly advices the use of the two Gas Arrestors. These Arrestors must be connected to the earth line 1 and terminals 4 and 5 of the landline (PSTN).

If you are installing the system in a place where the land line (PSTN) service is not available, or if you wish to increase the level of security of the system, these terminals also accept a GSM interface (such as Ness's SecureLink) which simulates the analogue land-line.

Ness provide two versions of the SecureLink GSM interface: SecureLink-G and SecureLink-GP. Both these devices simulate the analogue land line during line-down conditions (line trouble or wire-cutting) and allow the control panel to switch incoming/ outgoing calls to the GSM network.

You can also use the terminals on the SecureLink board to extend the functions provided by the SmartLiving system. The following section describes several methods which will allow you to provide users with advanced functions.

• Arming/Disarming the system over-the-phone using a cost-free call or SMS text By connecting one of the “follow zone” configured SmartLiving board terminals to an output on the SecureLink board, it will be possible to arm or disarm the SmartLiving system via SMS. In a similar way, using a “switching zone” configured terminal, it will be possible to arm or disarm the SmartLiving system simply by means of a recognized incoming call.

• Alarm warning to users via SMS text By connecting one of the alarm outputs of the SmartLiving control panel to an input on the SecureLink board, it will be possible to receive alarm warning via SMS text. The system can be set up to send an editable SMS text to 10 different contact numbers.

All the functions of the SmartLiving system which use the land line (voice dialer, answerphone, report communications and teleservice) can be managed completely over the GSM network by the SecureLink. The SecureLink also allows teleservice maintenance over the GSM network.

If there are ADSL filters on the line, you must connect the control panel downstream of the filters, to the line dedicated to telephone equipment (this line is clearly indicated on the filters). It is recommended all Alarms System be used only where ADSL filters are fitted.

3-1-7

Note

If a SecureLink is not used, connect the incoming PSTN line directly to terminals 4 & 5 of the SmartLiving main board.

Type-in Code

Enabling / Disable Phone Line Monitoring

(Installer PIN - Default 9999)

, PROGRAMMING Panel options .

one Line

Ph Monitoring

Press to enable the “Line Down Signal” option, or to disable it. Press to exit and save.

Note: Installation and maintenance to the phone line shall be performed by qualified licensed installers only.

26 Installation

Installation and programming manual

Connecting to a PC

Programming from a PC requires the SmartLeague software programme (refer to paragraph 6-3 Programming via the SmartLeague programme) and an RS232 serial cable.

Insert the RS232 serial link (accessory item) into the connector [A], as shown in the figure opposite.

If you wish to purchase an RS232 serial link, refer to the codes in Appendix H, Order codes. If your PC is not equipped with an RS232 port, but has a USB instead, you can use Ness's Approved RS232-USB adaptor (accessory item - Ness Part No 101-231).

Table 34:

SmartLiving end

DB9F connector

SmartLiving end

DB9F connector

RS232 connector cable

PC end

DB9F connector

2 3

3 2

4 4

5 5

6 6

7 7

8 8

PC end

DB25F connector

3 3

8 5

3-1-8

Connecting the SmartLogos30M

voice board (accessory item)

The SmartLogos30M voice board provides the SmartLiving system with an array of useful voice functions.

For proper installation of the board, work carefully through the following steps.

1. Disconnect all power sources to the control panel (mains and lead batteries).

2. Connect the board to the respective connector [B].

3. Power up the system from the mains and reconnect the lead batteries.

3-1-9

Installation 27

Maintenance status

MaintenK03 P05 DASIDASI--

Keypad address

Reader address

“RUN”

position

“SERV”

position

The maintenance status is signaled on the keypads by the “Maintenance” message and the address of the keypad. The address of the built-in reader (if enabled) of Alien keypads will also be shown.

During service/maintenance mode, the control panel:

• Forces the relay output on the motherboard (Table 5: Control panel - terminal board, 10-11-12) to standby status.

• Does not activate the outputs (and will force to standby any active outputs) triggered by:

•• alarm or zone/partition tamper

•• peripheral tamper

•• open/dislodged panel tamper

• It allows initialization of the keypad address programming phase.

• It allows initialization of the reader address programming phase.

• It initializes automatically the auto-enrollment of the peripherals connected to the BUS at 10 seconds intervals. It allows assignment of the addresses to the peripherals connected to the BUS and, at 10 second intervals, enrolls the peripherals it finds.

• The control panel will not reset the BUS in an attempt to retrieve peripherals in the event of peripheral loss.

• It will continue to operate as normal, except under the aforesaid circumstances.

During service/maintenance mode, the Alien keypad:

• Does not require user-code entry to access the sections which correspond to the “Settings” key.

• The first parameters shown in the “Settings - Alien” section are the addresses of the Alien keypad and its built-in proximity reader and, only for the Alien/S, the status of tamper enablement on the keypad.

• It is not possible to access the “Clima” section.

• The display shows the address of the Alien keypad and its built-in proximity reader in the top left-hand corner of the home page.

• The display shows the letters relating to the operating status of the partitions in the bottom left-hand corner of the home page.

3-1-10

The control panel can be placed in maintenance mode by:

• Inserting the Maintenance jumper in the “SERV” position.

• Enabling the “Maintenance” option in the ‘SmartLeague’ Software.

The Maintenance jumper (Table 4: Control panels - description of parts, Q) can be inserted in two different positions:

• “RUN” (control panel operating normally)

• “SERV” (control panel ready for maintenance work)

The control panel enters “Maintenance” mode when this option is enabled and exits “Maintenance” mode when it is disabled. You can enable/disable this option at the keypad or via computer.

Via Keypad

1. Access the “Programming Panel options” section.

Type-in Code

2. Press to enable the “Maintenance” option, or to disable it.

3. Press to exit and save.

(Installer PIN)

, PROGRAMMING Panel options .

Via PC

Select “SmartLiving System” from the tree menu on the left, then go to the “Programming” template on the right: The “Control panel parameters” section provides the “Maintenance” option, click-on this option to enable/disable it.

USING THE MAINTENANCE JUMPER

THE “MAINTENANCE” OPTION

28 Installation

Installation and programming manual

Shield + D S -

Control panel

IB100

IB100 IB100

BUS sections:

1 isolator in cascade

connection

IB100

BUS sections:

2 isolators in

cascade connection

BUS sections:

3 isolators in

cascade connection

3-2Connecting peripherals

The I-BUS line wiring

The SmartLiving peripherals (keypads, readers, expansions, sounderflashers, transceivers, isolators and GSM communicator) must be connected to the control panel via the I-BUS.

The connection between the control panel and its peripherals is achieved through a 4 wire (or more) cable.

If Shielded cable is used, the shield must be connected to one of the terminals (Negative or GND) at the control panel end only, and must run along the BUS without being connected to negative or GND at any other point.

The cable specifications depend on the length of the BUS (from the panel terminals to the most distant point), Baud rate and the load current draw.

Table 35:

Cable

AF CEI 20-22 II

4 wire cable + shield

6 wire cable + shield

Recommended cable

n. wires

2 0.5 + -

2 0.22 D S

2 0.5 + -

2 0.22 D S

2 0.22 available

2 0.75 + -

2 0.22 D S

2 0.22 available

Section (mm2)

I-BUS terminal

3-2-1

ATTENTION!

The maximum wire length of the I-BUS depends on the deployment of the peripherals connected to the line and their specific current draw (in particular the keypads and expansion boards). The power to peripherals and detectors can be supplied by external power stations or by the line itself.

Furthermore, the speed of the communication BUS (Baud rate) can be modified by means of the SmartLeague programming software. If the BUS is not used to power the peripherals and their loads, the maximum wire length is 300 meters @ 250kbs, regardless of the number of peripherals involved.

An intermediate speed (125kbs) can support a single section of 700 meters.

If you wish to increase the length and performance of the BUS, you can connect IB100 isolators.

If the speed of the communication BUS (Baud rate) is low (38.4 or 125 kbps), you can apply a maximum of 5 isolators in a cascade connection.

If the speed of the communication BUS (Baud rate) is high (250 or 2 kbps), you can apply a maximum of 2 isolators in a cascade connection.

You can connect up to 15 isolators in all.

It is extremely important to evaluate correctly the number of isolators connected in cascade to the BUS.

The following example will help you achieve a correct evaluation

ATTENTION!

Installation 29

Installing nCode/G and cCode/G

keypads

1. Connecting the device to the system

2. Pull the connection wires through the wire entry [A].

3. Connect the cables to the connector on the keypad backplate [B]. If you are using the connector provided with the KB100 kit [C], connect the wires to the terminals, in accordance with the instructions described in paragraph 2-3-2 nCode/G and cCode/G Keypads, then insert the connector into the guide [D] until it locks into place.

4. Using at least 2 screws, mount the bracket to the wall.

5. Using the back-locking grips, attach the keypad to the bracket (as shown in figure [E]).

6. Fasten the screw [F] (included) into the screw location [G], to secure the keypad properly to the bracket.

3-2-2

Installing Alien/S keypads

1. Connecting the device to the system

2. Pull the connection wires through the wire entry [A].

3. Connect the cables to the connector on the keypad backplate [B].

4. Using the respective anchor holes, mount the bracket to the wall or 503 box.

5. Using the back-locking grips, attach the keypad to the bracket (as shown in figure [C]).

6. Fasten the screw [D] (included) into the screw location [E], to secure the keypad properly to the bracket.

3-2-3

Installing the Alien/G keypad

1. Prepare the placement area on order to flush-mount the device, taking care not

damage any electrical wiring, gas or water papers, etc.

2. Insert the flush-mount box (Table 36: Alien/G - mounting possibilities, A) into the placement area and secure it in place.

3. Pull the wires through the most suitable wire entry.

30 Installation

3-2-4

+ 82 hidden pages

Ness SmartLiving 505, SmartLiving 10100, SmartLiving 515, SmartLiving 1050 Installation Manual

Specifications and Main Features

Frequently Asked Questions

User Manual