Ness D24 User Manual

D24

USER’S MANUAL

A$15.00

INC GST

Ness D24 control panel – User’s manual

Revision

2

ALARM CONTROL PANEL AND DIALLER

HEAD OFFICE:

Ness Security Products Pty Ltd
ACN 069 984 372
4 / 167 Prospect Hwy
Seven Hills NSW 2147 Australia
Ph [phone]
Fax [phone]
[e-mail]

SYDNEY
02 8825 9222

MELBOURNE
03 9878 1022

BRISBANE
07 3343 7744

ADELAIDE (Aquavia Controls)
08 8277 7255

PERTH
08 9328 2511

NEW ZEALAND (NFS NZ)
[phone]

“Australia’s largest

designer and

manufacturer of

high quality security

products”

WWW.NESS.COM.AU

Ness Security Products Pty Ltd

Quality
Endorsed
Company
ISO9001

LIC.No. QEC2074
NSW Head Office only

D24 USER MANUAL
REVISION 2 November 2002

Document Part Number: 890-252
For product: 100-660 D24 Control Panel

© 2002 Ness Security Products Pty Ltd ABN 28 069 984 372
D24user rev2 pmo131102

Specifications may change without notice.

NESS SECURITY PRODUCTS

TELECOMMUNICATIONS COMPLIANCE

Australian Communications Authority

CONTENTS

Features ................................................................................. 4

Keypad ................................................................................. 5

Keypad Display Table .......................................................... 6

View Menu Operation ........................................................... 7

OPERATION ......................................................................... 8

Arming ............................................................................... 9

Disarming .......................................................................... 9

AREA Operation .............................................................. 10

Arming & Disarming Areas ............................................ 11

Administrator Code ........................................................ 12

Monitor Mode .................................................................. 13

Panic Alarm ..................................................................... 14

Duress Alarm ................................................................... 14

Medical Alarm ................................................................. 15

Fire Alarm ........................................................................ 15

VIEW Menu ...................................................................... 16

VIEW Memory ................................................................. 17

Excluding Zones ............................................................. 19

Test Mode ........................................................................ 20

Siren Test ......................................................................... 21

PROGRAMMING

Programming Options Table ......................................... 21

How to Program .............................................................. 22

User Code programming .......................................... 22-23

Entry/Exit Timer programming ...................................... 24

Wireless Accessories .......................................................... 25

Installation Record .............................................................. 26

Operation Summary ........................................................... 27

NESS D24 CONTROL PANEL - USER MANUAL

4

• Pow erful multizone commercial
security

• 24 fully programmable zones

• Supports 8 Radio Devices (Radio
PIRs, Radio Reeds etc)

• Supports 8 Radio Keys

• Contact ID Dialler Format

• Ness Audible Dialler Format

• Separate 24 Hour Tamper input

• Single or Double Trigger Zones

• Remote LCD Keypads (Max 3)

• Fully programmable via the system
Keypad - Eliminates the need f or
expensive prog rammers or Proms.

• Inbuilt Vibration Sensor Analyser

• All programming data is permanently
stored in a non-volatile EEprom
memory

• True Dynamic Battery Test e v ery time
the Panel is Armed / Disarmed and
every hour

• Area Partitionable (3 Areas). An y Zone
can be programmed to any area, as
well as common areas

• Comes complete with an AC plug pac k
and supports a 12V 7Ah battery to
maintain system security under all
power supply conditions

• T w o separate Monitor Modes (Home
Mode)

• Outputs are separately fused with
Automatic Reset Fuses

• Day Mode and Door Chime feature .

• 30 Event Memory

• All inputs and outputs are heavily
protected against lightning and high
voltage supply transients. An earth
terminal is provided for extra protec­tion

• 30 User Codes

• Programmable Inputs to activ ate
selectable Outputs (Output Mapping)

• Manufactured with the latest SMD
Technology

• Ultra-Modern and Impact resistant
Housing

• Forced Arming Feature

NESS D24 FEATURES

NESS D24 CONTROL PANEL - USER MANUAL

5

D24 KEYPAD

2

5

8

0

1

4

7

P

3

6

9

E

E

ARM

VIEW

D24

MONITOR

EXCLUDE

PROGRAM BUTTON ENTER BUTTON

KEYPAD DISPLAY TEST:

Press and hold button.

PANIC
BUTTON
(Press & Hold)

BACKLIT
LCD ICON
DISPLAY

TM

F

MONITOR

ARM ZONE TAMPER SYSTEM POWER FIRE MEMORY

AREA 1 AREA 2 AREA 3 EXCLUDE PROGRAM TEST

20

12 13

21

4

10 119

191817

312

1614 15
2422 23

6578

AREA

NESS D24 CONTROL PANEL - USER MANUAL

6

KEYPAD DISPLAY TABLE

OFF ON

Flashing

FAST

Flashing

SLOW

ZONES

Zone sealed Zone unsealed

Zone Alarms
present (in Armed
or Monitor Mode)

ARM

Panel is
Disarmed

Normal

Normal

Normal

Normal

Normal

Normal

Normal

Panel is
Armed

ZONE

Displaying
Zone Status

TAMPER

Displaying
individual
Tamper Alarms

Tamper Alarms
present

SYSTEM

Displaying
individual
System Alarms

System Alarms
present

POWER

Displaying
individual
Power Alarms

Power Alarms
present

FIRE

Fire warning
(If enabled)

Fire alarm
(If enabled)

MEMORY

Memory Mode

or View key
pressed

New alarm in
Memory

MONITOR

Panel is in
Monitor Mode

AREA 1

Area 1 Armed Area 1 Monitor

AREA 2

Area 2 Armed Area 2 Monitor

AREA 3

Area 3 Armed

EXCLUDE

Exclude Mode Zone or other

alarm Excluded

PROGRAM

User Program
Mode

TEST

Siren Test

T

M

F

1-24

NESS D24 CONTROL PANEL - USER MANUAL

7

VIEW MENU OPERATION

MEMORY icon flashes to indicate
that Memory contains new events.
Memory can be viewed at any time.

E

M

TAMPER ALARMS

1 External Tamper
2
3
5

Control Panel Tamper
Zone input Tamper
Radio Interface Tamper

SYSTEM ALARMS

1
2
3
4
5
6
7
8
9

Keyswitch Panic
Dialler line fault
Keypad connection fault
Control Panel fault
Duress alarm
Panic alarm
Medical alarm
User Code alarm
Access to Installer Program mode

POWER ALARMS

1
2
3
4
9

0

Mains power failure
Backup Battery low
DC supply failed
Zone reference supply failed
Radio Device battery low

Radio Key battery low

(1-8 shows which device has low battery)

(1-8 shows which device has low battery)

1. Press

2.

3.

Memory icon turns on

Keypad icons will display the
most recent event as per the
Keypad Display Table

Press to cancel the
Memory display at any time

To view

alarms

TAMPER

To view

alarms

SYSTEM

To view

alarms

POWER

To view

MEMORY

4

VIEW

3

VIEW

2

VIEW

VIEW

VIEW

Step through the Memory
display by pressing the

button. At each step,
the keypad icons display the
history of Arming, Disarming
and alarm events.

VIEW

MEMORY DISPLAY

E

E

E

E

E

NESS D24 CONTROL PANEL - USER MANUAL

8

OPERATION

ARMING AND DISARMING

The Ness D24 micro computer based 24 zone
control panel is the heart of your security
system to which all your detection devices
connect.

Each Zone of the panel can be connected to
one or more detection devices to protect
separate rooms of your premises.

Detection devices may be connected to the D24
control system directly by cabling or with
optional wireless (Radio) devices.

The most common type of detection devices are
Passive Infra-Red Motion Detectors (or P.I.R’s
for short) and Reed Switches for doors and
windows.

OPERATING MODES

The Ness D24 will operate in one of the following
modes:

ARMED: The system is “On” and ready to detect
intrusion. 24 Hour Zones (if configured) are still
active. Area Partitioning means the panel can
be split into three separate “Areas” which can
be Armed and Disarmed independently of each
other.

DISARMED: The system is “Off”. This is the
normal mode when the premises are occupied.
Day Zones and 24 Hour Zones (if configured)
are still active.

DAY Mode: The system is Disarmed and a zone
or zones have been setup to create an alarm
when activated. Often used as a doorway alert
in a shop.

MONITOR Mode: Allows the system to be
“partially” Armed. For example, in a house, to
allow all perimeter zones, doors and windows,
to be Monitored (armed) at night.

24HR Zones: Zones that have been setup to
be active in any mode. Usually used for Tamper
switches and Panic buttons.

NESS D24 CONTROL PANEL - USER MANUAL

9

ARMING & DISARMING

The control panel must be Armed prior to
vacating the premises in order to detect
intruders. Ensure that the panel is not in
Program, Memory or Exclude modes.

Note: If the panel is already in alarm, you must first
silence the alarm before you can Arm.

SIREN WARNING:

At the end of the exit time, all zones should be
Sealed. If any are Unsealed, the siren will sound
for 2 seconds as a warning to indicate that those

ARMING THE SYSTEM

If the D24 has not been programmed for Area operation, this method will Arm the entire system.

Press... (If Two Button Keypad Operation is disabled. This is the factory default.)

...or (If Two Button Keypad Operation is enabled.)

...or [CODE] (If Shortcut Arming is disabled.)

Three beeps will sound and the ARM icon will turn ON

ARM

Leave the premises within the Exit Delay Time. At the end of Exit Delay Time, 1 beep will sound

zones have been automatically excluded. For
maximum security, you should return, Disarm,
check the premises and then Arm again.
Continual warnings could mean that a detector
is faulty and may have to be manually excluded.

AUTO EXCLUDE:

If the auto-exclude option is disabled, the siren
will sound for the duration of reset time if a zone
is Unsealed at the end of exit time.

DISARMING THE SYSTEM

If the D24 has not been programmed for Area operation, this method will Disarm the entire system.

Press... [CODE]

Three beeps will sound and the ARM icon will turn OFF

ARM

Disarm the panel during the Entry Delay Time to prevent unwanted “Alarm on entry”.
An error beep when attempting to Disarm may indicate:

Incorrect Code
or the panel is already Disarmed
or the panel is in Exclude mode

See Page 12 for Disarming Areas