Ness 104-443 User Manual

Page 1
Ness 104-443 HD-SDI camera
REV1.3 Nov11
User’s Manual
Page 2
COPYRIGHT NOTICE
All rights reserved. No part of this publication may be reproduced, transmitted or stored in a retrieval system in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of Ness.
© 2011 Ness Corporation Pty Ltd ABN 28 069 984 372
HEAD OFFICE: Ness Security Products Pty Ltd ABN 28 069 984 372 Ph +61 2 8825 9222 Fax +61 2 9674 2520 ness@ness.com.au
SYDNEY Ph 02 8825 9222 Fax 02 9674 2520 sales@ness.com.au
MELBOURNE Ph 03 9875 6400 Fax 03 9875 6422 nessmelb@ness.com.au
BRISBANE Ph 07 3399 4910 Fax 07 3217 9711 nessbris@ness.com.au
PERTH Ph 08 9328 2511 Fax 08 9227 7073 nessper@ness.com.au
ADELAIDE Ph 08 8152 0000 Fax 08 8152 0100 adelaide@ness.com.au
www.ness.com.au
Page 3
1
Table of Contents
1. Overview.................................................................................................................................. 2
1.1 Features ........................................................................................................................2
1.2 Package Contents ......................................................................................................... 3
1.3 Dimensions.................................................................................................................... 3
2. Camera Cabling....................................................................................................................... 4
2.1 Product Application ....................................................................................................... 4
2.2 Connectors .................................................................................................................... 5
2.3 TV System/Resolution/Frame Rate Setup .................................................................... 6
2.4 Lens Mounting............................................................................................................... 6
Appendix A: Technical Specifications.......................................................................................... 7
Appendix B: Back Focus Adjustment........................................................................................... 8
Page 4
2
1. Overview
HD-CCTV standard offers a new opportunity for traditional CCTV surveillance
industry. It makes CCTV Camera transmit high definition image through coaxial
cable. Combing SDI standard with high quality SONY CMOS sensor, the SDI
Box Camera provides 1920x1080 resolution high quality image as well as easy
and low-cost installation. With innovative WDR function and digital noise
reduction technology, the SDI Box Camera can offer close-up images with
exceptional details even at night time.
1.1 Features
z Progressive Scan CMOS Sensor
z Full HD 1080P @ 30fps/60fps
z HD 720P @ 30fps/60fps
z Wide Dynamic Range
z Digital Noise Reduction
z Intuitive OSD Operation
z BNC output support
z DC12V Support
z AC24V Support*
z RS-485 Support*
z Alarm I/O Support*
(*) Optional
Page 5
3
1.2 Package Contents
Please check the box contains the items listed here. If any item is missing or
has defects, DO NOT install or operate the product and contact your dealer for
assistance.
SDI Box Camera
Back focus adjuster
CD
(bundled software and documentation)
Quick Guide
1.3 Dimensions
Page 6
4
2. Camera Cabling
Please follow the instructions below to complete SDI Box Camera cable
connections.
2.1 Product Application
Connect the SDI Box Camera to other devices as shown in the diagram to
complete a video surveillance solution.
Page 7
5
2.2 Connectors
The diagram below shows the IP Camera’s reset button and various connectors.
Definition for each connector will be given as follows.
Single Board Dual Board
Item Definition Remark
A
PWR Power connection indication (green light)
B
AUTO IRIS Connector Auto Iris Lens connector
C
RESET Reset
D
SDI OUTPUT SDI signal output
E
/ / / / ENTER
OSD control key
Single Board DC12V Power connector
AC 24V: AC_IN 1 DC 12V:
DC12V
AC 24V: GND DC 12V:
GND
F
Dual Board DC12V/AC24V
AC 24V: AC_IN 2 DC 12V:
DC12V
G
VIDEO BNC output
H
DIP Switch TV system/ Resolution/ Frame Rate Setup/ BNC
1 ALARM_GND 5 T­2 ALARM_IN+ 6 T+ 3 ALARM_OUT- 7 R-
I
Alarm I/O
4 ALARM_OUT+ 8 R+
Page 8
6
2.3 TV System/Resolution/Frame Rate Setup
Please refer to the illustrations below to set up the Camera TV system,
resolution and frame rate.
Setting
Pin Definition
ON OFF
1
TV System NTSC PAL
2
Resolution 720P 1080P
3
Frame Rate 50/60 25/30
4
Reserved - -
5
Reserved - -
6
BNC ON OFF
Please kindly notice that while BNC output is on, there will be no SDI
signal.
2.4 Lens Mounting
If use C-Mount lens, after removing the camera’s plastic cover, users need to
mount the C/CS mount adapter to the camera. Then attach the lens onto the
C/CS mount adapter, as the illustrations shown below.
C/CS Mount Adapter Completion
Page 9
7
Appendix A: Technical Specifications
Camera Sensor
1/2.8” Sony Progressive CMOS
Total Pixel
2144 (H) x 1588 (V), 3.4M
Shutter Speed
1/30 ~ 1/10000 sec.
A/D Converter
10 /12 bit
Lens C/CS Mount Lens
Fixed / Vari-focal
Operation Video Streaming
1080P / 720P
30/60 fps, 25/50 fps @1080P
Frame Rate
30/60 fps, 25/50 fps @ 720P
AE Mode
Auto / Shutter / IRIS / Manual
Back Light Compensation
On / Off
White Balance
Auto / Indoor / Outdoor / ATW / Manual
Digital Noise Reduction
On / Off
Wide Dynamic Range
On / Off
IR Function
Auto / On / Off
Aperture
1 ~ 16
Image Setting
Privacy Mask
16
Mechanical Lens Mounting
C / CS Mount
SDI
75
Video Output
BNC
1.0 Vp-p / 75
Remote Control*
Up to 2 sets RS-485
DIP Switch
6 pin
TACT Switch
5 pin (OSD Control)
Auto Iris
DC Drive
Connectors
Alarm In/Out*
Up to 2 sets
General Dimension
125 x 82 x 52 mm (L x W x H) (w/o Lens)
Weight
330 g (0.73 lbs)
Power Source
DC 12V±10% / AC 24V*±10%
Power Consumption
Max 5W
Regulatory
CE, FCC, RoHS
(*) Optional
Page 10
8
Appendix B: Back Focus Adjustment
When to adjust back focus
Back Focus refers to the distance from the rear lens element to the camera focal plane. In
most cases, it is required to adjust back focus only when the camera’s lens cannot hold
focus throughout its zoom range.
What requirements
Tools required when carrying out back focus adjustment include:
1. Back focus adjuster (in the IP Camera’s package)
2. Test chart / contrasting object
How to adjust back focus Step 1: Set the camera on a stable mount, with the test chart or object at least 75 feet (23
meters) away (or as far as possible).
Step 2: Make sure the iris is wide open. Therefore, it is advised to keep the environment
in low light condition.
Step 3: Adjust the focus to infinite far (∞).
Step 4: Turn the zoom to the extreme telephoto position, and then focus on the subject.
Step 5: Set the zoom to wide-angle position.
Step 6: Loosen the back focus ring’s retaining screw with the supplied adjuster, and adjust the back focus ring for sharp picture.
Step 7: Repeat steps 3 ~ 6 until focus can stay the same throughout the zoom range.
Step 8: Tighten the back focus ring’s retaining screw to fix the ring.
Loading...