Ness IQ, SDI, 104-527, 104-528, 104-529 User Manual

4, 8 & 16 Channel

Standalone Digital Video Recorder

Ness IQ-Series

960H & SDI

Model

User Manual

DVR’s

Digital Video Recorder for Ness IQ-

Series

This manual covers the following DVR’s

4 Channel 960H (104-

527), 8 Channel 960H (104

4 Channel SDI (104-

452), 8 Channel SDI (104

FCC Compliance Statement

Notice to Users:

This equipment has been tested and found to comply with

15 of the FCC Rules, these limits

are designed to provide reasonable protection against harmful interference when the

equipment is operated in a commercial environment. This equipment generates, use

and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential area is likely to cause harmful interfer

will be required to correct the interference at own expense.

CAUTION

CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE COULD VOID THE

USER’S AUTHORITY TO OPERATE THE EQUIPMENT.

ATTENTION

DES CHANGEMENTS OU DES MODIFICATIONS NON EXPRESSEMENT APPROUVEES PAR LE RESPONSABLE DE LA CONFORMITE

POURRAIENT ANNULER L'AUTORISATION DE L'UTILISATEUR A EXPLOITER L'EQUIPEMENT.

The equipment complies with the requirement of FCC CFR 47 PART 15

Explanation of Graphical Symbols

Warnings



Installation and servicing should be performed only by



Power off the DVR when connecting cameras, audio, or sensor cables.



The manufacturer is not responsible for any damage caused by improper use of the

the product.

 The manufac

turer is not responsible for any problems caused by or resulting from the user physically opening the DVR for

examination or attempting to fix the unit.



The manufacturer may not be held liable for any issues with the unit if

This symbol indicates the presence of important operating and maintenance (servicing) instruction in the

literature accompanying the product.

This symbol indicates the presence of non

that may be of sufficient magnitude to constitute a risk of electric shock

Ce symbole indique la présence d’instructions

accompagnant le produit

Ce symbole indique la présence de «

conséquence un risque de la décharge électrique aux personnes

960H & SDI DVR

-528) & 16 Channel 960H (104-

529)

-441) & 16 Channel SDI (104-

442)

the limits for a Class A digital device.

s and can radiate radio frequency energy

SUBPART B, Class A.

qualified and experienced personnel.

product or failure to follow instructions for

any labels are removed

in the p

-insulated “dangerous voltage”

within the product’s enclosure

to persons.

importantes et de maintenances dans le manuel

haute tension » non-

isolé dans le produit qui peut avoir pour

.

Page

2

Pursuant to Part

ence in which case the user

roduct.

Digital Video Recorder for Ness IQ-

Series

Cautions

 This product has free voltages (100V ~

2

 This product uses a Lithium battery.
 To avoid any

risk of explosion, do not replace the battery



Dispose of used batteries according to the manufacturer’s instructions.



This equipment and all communication wirings are intended for indoor use only.

 To reduce

the risk of fire or electric shock

WEEE(Waste Electrical and Electronic Equipment)

Important Safeguards

1. Read Instructions

 To reduce

the risk of fire or electric shock, do not expose the unit to rain or moisture.

2. Retain Instructions


The safety and operating instructions should be retained for future reference.

3. Cleaning


Unplug this equipment from the wall outlet before cleaning it. Do not use liquid aerosol cleaners. Use a damp soft cloth for

cleaning.

4. Attachments


Never add any attachments and/or equipment without manufacturer approval as such additions may result in the

electric shock, or other personal injury.

5. Water and/or Moisture


Do not use this equipment near water or in contact with water.

6. Accessories


Do not place this equipment on an unstable cart, stand or table. The equipment may fall, causing seriou

adult and serious damage to the equipment.



Wall or shelf mounting should follow the manufacturer’s instructions and should use a mounting kit approved by the

manufacturer.



Move this equipment and cart combination with care. Quick

equipment and cart combination to overturn.

7. Power Sources


This equipment should be operated only from the type of power source indicated on the marking label. If not sure the type of

power, please consult to distributor

or local power company.

8. Power Cords


Operator or installer must remove power, BNC, alarm and other connections before moving the equipment.

9. Lightning


For added protection for this equipment during a lightning storm, or when it is left u

time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the equipment

due to lightning and power-line surges.

10. Overloading


Do not overload wall outlets and extensi

11. Objects and Liquids


Never push objects of any kind through openings of this equipment as they may touch dangerous voltage points or short out

parts that could result in a fire or electric shock.

 Never s

pill liquid of any kind on the equipment.

Customers in European Union countries are advised to dispose this product, at the end of its

useful life, as per applicable local laws, regulations and

960H & SDI DVR

4

0V). See installation instructions before connecting to the power supply.

on the main board by anything other than a Lithium battery.

, do not expose the unit to rain or moisture.

stops, excessive force and uneven surfaces may cause the

nattended and unused for long periods of

on cords to avoid the risk of fire or electric shock.

procedures.

Page

3

risk of fire,

s injury to a child or

Digital Video Recorder for Ness IQ-

Series

12. Servicing



Do not attempt to service this equipment yourself. Refer all servicing to qualified service personnel.

13. Damage Requiring Service


Unplug this equipment from the wall outlet and refer servicing to qualified

① When the power-

supply cord or the plug has been damaged

②

If liquid is spilled or objects have fallen into the equipment

③

If the equipment has been exposed to rain or water

④ If the equipment does not operat

e normally by following the operating instructions, adjust only those controls that are

covered by the operating instructions as an improper adjustment of other controls may result in damage and will often

require extensive work by a qua

lified technician to restore the equipment to its normal operation.

⑤

If the equipment has been dropped or damaged the cabinet

⑥

When the equipment exhibits a distinct change in performance

14. Replacement Parts
 When replacement

parts are required, ensure the service technician uses replacement parts specified by the manufacturer

or that have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or

other hazards.

15. Safety Check


Upon completion of any service or repairs to this equipment, ask the service technician to perform safety checks to

determine that the equipment is in proper operating condition.

16. Field Installation


This installation should be made by a qualified service

17. Correct Batteries

CAUTION

RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.

DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS

ATTENTION

RISQUE D'EXPLOSION SI LA BATTERIE EST REMPLACÉE

DISPOSEZ DE BATTERIES EN ACCORS AVEC LES INSTRUCTIONS

18. Operating Temperature


An operating temperature range is specified so that the customer and installer may determine a suitable operating

environment for the equipment.

19. Elevated

Operating Ambient Temperature

 If installed in a closed or multi-

unit rack assembly, the operating ambient temperature of the rack environment may be

greater than room ambient. Therefore, consideration should be given to installing the equipment in an envir

compatible with the specified operating temperature range.

20. Reduced Air Flow


Installation of the equipment in the rack should be such that the amount of airflow required for safe operation of the

equipment is not compromised.

21. Mechanical Loading
 Mou

nting of the equipment in the rack should be such that a hazardous condition is not caused by uneven mechanical

loading.

22. Circuit Overloading


Consideration should be given to connection of the equipment to supply circuit and the effect that overloading of

might have on over-

current protection and supply wiring. Appropriate consideration of equipment nameplate ratings should

be used when addressing this concern.

23. Grounding (Earthing)
 Conn

ection of ground wire is highly recommended to protect the DVR

electrical surge.

Warning

WARRANTY IS VOID IF SEAL OR LABEL IS REMOVED OR DAMAGED.

960H & SDI DVR

service personnel under the following conditions:

.

.

.

.

—

this indicates a need for service.

person and should conform to all local codes.

PAR UN TYPE INCORRECT

from external

electri

Page

4

onment

circuits

c shock, such as lightening,

Digital Video Recorder for Ness IQ-

Series

The List of Configuration

DVR Set

CD Containing

Manual / CMS CD

Remote Controller

Manual

Screws

HDD Brackets

Rack Bracket

(Rack mount models only)

Data Cable

Power Cable

Power Adapter

960H & SDI DVR

4 / 8 Channel 960H & (104

-

4 channel SDI (104

16 Channel

960H (104

8 / 16 Channel SDI (104-

441 & 104

Page

5

527, 104-528)

-452)

-529) &

-442)

Digital Video Recorder for Ness IQ-

Series

Operation

 Power Off



Do not turn DVR off, or plug off the power adapter while

permanent damage to the equipment. Please click

power after DVR is shut

down completely. It is safe to wait for 5 seconds before turning the power on again.



Do not turn DVR off, or plug off the power adapter while

external hard disk and the like) in

use. Otherwise, it may cause permanent damage to the equipment. Make sure that the

power switch is in the “ON” position until data storage is completed. Please be aware that removing the storage device

cause the same damage to the equipment.

 Do not turn DV

R off, or plug off the power adapter

damage to the equipment. Make sure that the power switch is in the “ON” position until the formatting of the disk is

completed.

 HDD Installation / Ad

dition / Moving / Replacement / Removal



For installation/addition/replacement/Removal of HDD (DVD

cause permanent damage to the HDD (DVD

 When wish

to power DVR off, please click

DVR is shut down completely.



Installation/Addition/Moving/Replacement:

recognize the hard disk and may begin to function

①

(Date/Time setup) Set up the current date and time (SETUP>SYSTEM>Admin>Date/Time).

② (Initialization of system setup

) All setup values are restored to original factory default settings.

(SETUP>SYSTEM>Information>Status>Setup>Default).

③ (HDD format

) HDD format is done by SETUP>SYSTEM>Admin>Storage>Format. If there are more than two HDDs,

each must be formatted, separately. When the format is completed, DVR will auto

 Removal: Follow

the Remove procedure even when a pre

-

SETUP>SYSTEM>Admin>Storage>Format, click

corresponding HDD to discard ‘HDD’ item. When the Remove procedure is completed,

 Date / Time Change



Any change in Date/Time is immediately applied onto live video (LIVE), but the date/time when the recording was done are

not changed.

 Make sure to

reboot DVR after adjusting the Date/Time.

 Also, do not forget to

execute SETUP>SYSTEM>Shutdown in sequence before reboot.

 Upgrade



Do not upgrade until install a hard disk drive. Make sure

 Using a Mouse

 Left mouse button:

have the same function as

 Central button (wheel):

have the same function as

 Right mouse button:

display a number of ‘Function keys’ (please see ‘Input Device and Screen Icons>Using a mouse’ in

this manual).

 PLAY / PAUSE Key

 Press the PLAY/PAUSE key to one-

touch playback on the viewing screen (playback the recorded video from the last one

minute).

 Every time pressing the PLAY/PAUSE

key during playback mode, it is changed to ‘1X PLAY’ and ‘PAUSE’. The displayed

sign on the screen also changes from

 If wish

to change mode (1X PLAY, REW, FF, BACKWARD, FORWARD) during playback, always press the

key first (please see if the sign II

is shown on the screen).

 Press the PLAY/PAUSE

key to back up. Make sure that the backup is done in ‘PAUSE’ mode.

 Camera Title



Camera Title displayed in Record and Playback modes of DVR is set to CAM1 ~CAM16. Registering camera title in setup

menu (DEVICES>Camera/PTZ>Title) is to make every setup process easier.

960H & SDI DVR

Precautions

DVR is in operation (record/playback)

( ) SETUP>SYSTEM

>Shutdown sequentially and then remove the

External storage

device (e.g., USB memory stick, removable

during the format of the hard disk

. Otherwise, it may cause permanent

-

RW), make sure that DVR is turned off. Otherwise, it may

-RW).

( ) SETUP>SYSTEM

>Shutdown sequentially and then remove the power after

Start ‘HDD initialization’ including

formatting. Otherwise, DVR wo

abnormally. Please follow the below procedure for ‘HDD initialization’.

-reboot.

-

installed hard disk has been removed.

(

) ‘Removed’ item under the discrete Format headings of a

DVR will auto

that

upgrade when the hard disk drive is in proper operation.

Enter ( ) on the Front panel of DVR.

Search

key on the Front panel of DVR(display search menu)

to II.

Page

6

. Otherwise, it may cause

uld not

-reboot.

.

PLAY/PAUSE

Digital Video Recorder for Ness IQ-

Series

1.

Product Features

1.1 Unpacking



This equipment is an electronic appliance, so it should be handled with special care.



After unpacking, please check if all the following items are

- DVR Main body

-

4 / 8 Channel 960H

(104-527, 104

-

-

16 Channel 960H (104-

529) & 8 / 16 Channel SDI (104

6.67A)

- Remote Control With 2 AAA batteries

- Installation CD (CMS Software &

User’s Manual)

1.2 Service



If there is any problem in the product, please refer servicing to a supplier or a distributor with qualified service personne

Warning

WARRANTY IS VOID IF SEAL OR LABEL IS REMOVED OR

960H & SDI DVR

included.

528)

& 4 channel SDI

(104-452)

: Power Supply (DC 12V,

-441 & 104-442):

Power Supply Adapter (DC 12V,

DAMAGED.

Page

7

5A)

l.

Digital Video Recorder for Ness IQ-

Series

1.3

System Connection Diagram

4 / 8

960H & SDI DVR

Channel 960H (104-527 / 104-528) &

4 Channel SDI (104-452)

Page

8

Digital Video Recorder for Ness IQ-

Series

960H & SDI DVR

16 channel 960H (104-529) &

Page

9

Digital Video Recorder for Ness IQ-

Series

Installation

1.4 Hard disk and DVD-

RW Installation

1.4.1 SATA Port



When installing HDDs, make sure to connect from SATA 1 Port.



4 / 8 Channel

960H & 4 Channel SDI

- Main substrate of this DVR has two

SATA port: it is indicated as SATA



16 Channel

960H & 8 / 16 Channel SDI

-

Main substrate of this DVR has five SATA ports: they are indicated as SATA 1, 2, 3, 4 and SATA 5.

- Please mount DVD-RW at the SATA

4

4 / 8 CH 960H &

4 channel SDI DVR

Storage

HDD

16 CH 960H &

8 / 16 Channel SDI DVR

Storage

HDD

1
2
3
4
4

1.4.2 Internal SATA Storage

 16 channel

960H & 8 / 16 channel SDI

 SATA Ports 1-4:

It is designed to mount HDD.

 SATA Port 5: Please mount DVD-RW.
 Only one DVD-

RW can be installed among the SATA Ports.

1.4.3 e-

SATA External Storage

 These series DVRs have one

external SATA Port; the picture above shows external

 SATA Port 6

: It is designed to mount 4HDDs

1.4.4 HDD Installation



Securely fix a hard disk by using bracket and screws provided herewith.



Please do not use any different hard disk cables (data cable and power supply cable) other than ones we provide.

 Otherwise, it may cause

damage to the hard disk.

960H & SDI DVR

1 and 2.

port.

SATA 1, 2 Port

1

1 HDD
2 HDD

SATA 1, 2

, 3, 4, 5

DVD-RW 1 2 3

1 HDD --- --­1 HDD HDD --­1 HDD HDD HDD
1 HDD HDD HDD
0 HDD HDD HDD

DVR have 5 internal SATA Ports.

Connect from SATA 1 port when installing HDDs.

(16 Channel

960H & 8 / 16 channel SDI

SATA 6 Port

per each external SATA Port.

Page

10

2

---

HDD

Port

4 5

--- DVD-RW

--- DVD-RW

--- DVD-RW
HDD DVD-RW
HDD ---

)

.

Digital Video Recorder for Ness IQ-

Series

CAUTION

INSTALL HARD DISK AF

TER DVR POWER IS OFF. OTHERWISE, IT MAY CAUSE PERMANENT DAMAGE TO THE HARD DISK. TO

TURN OFF DVR, PLEASE CLICK ( )

SETUP>

SUPPLY AGAIN.

CAUTION



FOR INSTALLATION/ADDITION/REPLACEMENT/REMOVAL OF HDD (DVD

OFF. OTHERWISE, IT MAY CAUSE PERMANENT DAMAGE TO THE HDD (DVD



INSTALLATION/ADDITION/MOVING/REPLACEMENT

FORMATTING. OTHERWISE, DVR WON

ABNORMALLY. PLEASE FOLLOW THE BELOW PROCEDURE FOR

①

(DATE/TIME SETUP)

SET UP THE CURRENT DATE

②

(INITIA

LIZATION OF SYSTEM SETUP)

-

(SETUP>SYSTEM>

INFORMATION>STATUS>SETUP>DEFALUT)

③

(HDD FORMAT) HDD

FORMAT IS DONE BY S

HDDS, EACH MUST BE FORM

MATED SEPARATELY. WHEN THE FORMAT IS COMPLETED, DVR WILL AUTO

 REMOVAL

: FOLLOW THE REMOVE PROCEDURE EVEN WHEN A PRE

REMOVED. –

SETUP>SYSTEM>ADMIN>STORAGE>FORMAT, CLICK

FORMAT HEADINGS OF A CRRESPONDING HDD TO DISCARD

DVR WILL AUTO-REBOOT.

1.4.5

Maximum HDD Capacity



Each model has a different HDD capacity recognition.

 Below table shows the recommended

maximum HDD capacity for each model.

Type

4 / 8 Channel 960H

& 4 Channel SDI

Max Capacity 6TB

1.4.6 DVD-RW installation

 Securely fix DVD-

RW by using bracket and screws provided herewith.

 Please do not use any different DVD-

RW cables (data cable and power supply cable) other than the ones we provide.



Otherwise, it may cause damage to the DVD

 Only one DVD-

RW can be used. Mount it at the

CAUTION

INSTALL DVD-

RW OR/AND HARD DISK AFTER DVR POWER OFF. OTHERWISE, IT MAY CAUSE PERMANENT DAMAGE TO THE

HARD DISK. TO TURN OFF DVR, PLEASE CLICK

PLUGGING IN POWER SUPPLY AGAIN.

960H & SDI DVR

SYSTEM>SHUTDOWN. ALSO,

WAIT FOR 5 SECONDS BEFORE PLUGGING IN POWER

-

RW), MAKE SURE THAT DVR IS TURNED

-RW)

: USER SHOULD START ‘

HDD INITIALIZATION

’

T RECOGNIZE THE HARD DISK AND MAY BEGIN TO FUNCTION

‘

HDD INITIALIZATION

AND TIME (SETUP>SYSTEM>ADMIN>D

ATE

ALL VALUES IN SETUP ARE RESTORED TO FACTORY DEFAULT SETTINGS.

ETUP>SYSTEM>ADMIN>STORAGE>FORMAT. IF

-

INSTALLED HARD DISK HAS BEEN

( ) ‘REMOVED’

ITEM UNDER THE DISCRETE

‘HDD’

ITEM. WHEN THE REMOVE PROCEDURE IS COMPLETED,

16 Channel 960H &

8 / 16 Channel SDI

12TB

-RW.
SATA port 5 (16 channel

960H & 8 / 16 channel SDI

( ) SETUP>SYSTEM>SHUTDOWN. ALSO,

WAIT FOR 5 SECONDS BEFORE

Page

11

’ INCLUDING

’.

/TIME)

THERE ARE MORE THAN TWO

-REBOOT.

Only).

Digital Video Recorder for Ness IQ-

Series

1.5 Connector Wiring

1.5.1 Video-In/Loop

Out Connections

 Connect a camera to ‘VIDEO IN’.
 Assure the ‘VIDEO IN’ and ‘LOOP OUT

’ connections are connected properly, not oppositely.

NOTE

Only the 16 channel

960H and 8 / 16 channel SDI

1.5.2

Monitor Connections (Video Out, VGA and

 Video Out

- Use with the CCTV monitor.

-

Connect BNC cable between CCTV monitor and

 VGA

- Use with a computer monitor.

- Connect VGA cable between

computer monitor and

 Multi Spot

-

This function supports Multi Channel Display on Spot Monitor

-

Connect BNC cable between spot monitor and multi spot port of rear panel.

CAUTION

BLA

CK SCREEN WILL APPEAR IF THE MONITOR DOEST NOT SUPPORT THE SELECTED RESOLUTION.

DURING BLACK SCREEN, SYSTEM WILL AUTOMATICALLY GO BACK TO THE PREVIOUS RESOLUTION IN 15 SECONDS.

1.5.3 HDMI Connections



Connect HDMI cable to HD out port of rear panel and HDMI port of HD output device.

 Please click ( ) SETUP> DISPLAY>

VGA and the following screen will appear.

 Click the box below to select resolution.

-

User can select the resolution among ‘1920x1080 RB’, ‘1920x1080’, ‘1680x1050 RB’, ‘1680x1050’, ‘1280x1024’, and

‘1024x768’

- The default setting of DVR is ‘1280 x

1024’.

 Click the box below to select

signal format

- User can select the signal output

among ‘

- The default setting of DVR is ‘AUTO’

960H & SDI DVR

supports LOOP OUT connection.

Multi Spot)

‘VIDEO OUT’ of the DVR.

‘VGA’ of the DVR

.

NTSC’, ‘PAL’ and ‘AUTO’.

Page

12

UNLESS USER PRESS ‘OK’

Digital Video Recorder for Ness IQ-

Series

CAUTION

HDMI CONNECTION MAY NOT BE COMPATIBLE WITH CERTAIN OUTPUT DEVICE.

VIDEO NOISE MAY OCCUR

DEPENDING ON THE TYPE OF HDMI CABLE USED. MAKE SURE TO USE AN HDMI

CAUTION

BLACK SCREEN WILL APPEAR IF THE MONITOR DOEST NOT SUPPORT THE SELECTED RESOLUTION. UNLESS USER PRESS

DURING BLACK SCREEN, SYSTEM WILL AUTOMATICALLY GO BACK TO THE PREVIOUS RESOLUTION IN 15 SECONDS.

1.5.4 Audio Connections

 Connect an audio device to ‘AUDIO IN

’ and a speaker system to ‘

adjustable.

1.5.5

TCP/IP(Ethernet) Connections

 Connect to ‘ETHERNET

’ connector with the LAN cable.



When connect to Internet, use an ordinary LAN cable (Non

use only ‘Crossover cable’.

1.5.6 Alarm Connections(

TTL)

 Conne

ct Alarm Input (Sensor) to ‘AI 1~AI



Connect Alarm Output (buzzer, siren, etc.) to ‘

1.5.7 Master Alarm

 Alarm In sensor will

be deactivated if Master Alarm is on.

 Connect Master Alarm In to ‘4M

’ connectors.

1.5.8 Alarm Connections(

Relay (Dry Contact)



Connect Alarm Output (buzzer, siren, etc.) to ‘

to ‘GND’ connector.

1.5.9 RS-

485/422 Connections

 PTZ Camera connector.
 Please use TX+, TX-, RX+ and RX-

terminals.

1.5.10 RS-485 Over Coax

Connection

 PTZ Camera Connector
 Please connect Coax to ‘Video In’ and

select any Protocol in Camera/PTZ setup.

NOTE

PTZ Camera must support RS-

485 over Coax function

NOTE

When selecting Protocol, user can choose any protocol from the Protocol list other than

485 over Coax will not work.

960H & SDI DVR

AUDIO OUT

’. Please use a speaker system with volume

-

cross cable). However, when connect

4 (or AI

16)’ connectors and connect Sensor Common to ‘G’ connector.

AO 1~AO 4 (or AO 16)

’ connectors and connect Common to ‘

)

NO or NC 1~ NO or NC 2’ connectors, Power

to ‘

.

in order to use this feature.

‘NONE’. If ‘NONE’

is selected then

Page

13

-CERTIFIED CABLE.

‘OK’

directly to a PC, please

G’ connector.

COM’ connector and Ground

RS-

Digital Video Recorder for Ness IQ-

Series

1.5.11 USB Connections

 There are up to

four identical USB ports in front and in rear. It is possible to connect a USB memory stick to archive data or

a mouse to control the device.

1.5.12 RS-232 Connections



This port is not in use for users. Do not connect any devices

CAUTION

W

HEN USING THE RS232 SERIAL PORT, USERS MUST REQUEST FOR ASSISTANT TO QUALIFIED TECHNICAL PERSON OR

SERVICE REPRESENTATIVE.

1.5.13 Grounding (Earthing)



Connection of ground wire is highly recommended to protect the DVR from external

electrical surge.

1.5.14 Factory Reset Switch



Reset the switch to restore all setup values of menus to factory default settings. It is also

Log file.



The switch is located in a pin hole of the back panel.



Put the clip pin into the switch hole on the monitor (Live) screen and keep pressing until the switch has clicked.

CAUTION

P

RESS FACTORY RESET SWICH ONLY IN LIVE MODE

1.5.15

Power Supply connections



4 / 8 Channel:

960H & 4 Channel SDI

to ’DC12V

’ connector and plug another side to

Please do not use any different power supply adapter because it may cause the DVR to malfunction.



16 Channel

960h & 8 / 16 Channel SDI

to ’DC12V

’ connector and plug another side to power source. Adapter input voltage is a free volt (100 VAC ~ 240 VAC).

Please do not use any different power supply adapter because it may cause the DVR to malfunction.

1.5.16 Connections Guideline

 Video Out Connector:

If only the monitor is connected to

rear side of the monitor to 75 ohms to prevent abnormally bright or collapsed images.

a recorder) to the back of the monitor, please set the impedance switch on the rear side of the monitor to

Impedance) and set the last device to 75 ohms.

 Alarm Input Connector:

Do not input any type of voltage to the AI 1~AI

960H & SDI DVR

through this port.

electri

c shock, such as lightening,

possible to use to initialize System

NEVER PRESS IN SETUP MODE.

Plug the power supply adapter (DC 12V, 5A)

which include in this product

power source. Adapter input voltage is a free volt (100 VAC ~ 240 VAC).

: Plug the power supply adapter (DC 12V, 6.67

A)

VIDEO OUT connector, please set the impedance switch on the

If wish to connect another devi

4 (AI 16) connectors.

Page

14

which include in this product

ce (e.g.,

HIGH Z (High

Digital Video Recorder for Ness IQ-

Series

2.

Input Device and Screen Icons

2.1 Key and LEDs

4 / 8 channel 960H & 4 channel SDI

KEYS Icons

Direction Keys ▲▼◄►

• Control Pan/Tilt rotation of up/down/left/right in PTZ mode

•

Up/Down/Left/Right on screen cursor control

MENU

•

Enter the Main Menu (Setup mode)

DISPLAY

• Select 1/4/9/16 channel display

ARCHIVE

• Copy video data into the external storage device

FREEZE

• Screen freeze mode on/off

EMERGENCY

• Emergency recording on/off

Power LED

(Red)

•

Light off: DVR off

• Light on: DVR on

HDD LED

(Green)

• Light off: Stop recording

• Blink : Recording/Playback modes (HDD Access), Archive in operation

Network LED

(Yellow)

• Light off: failed to connect to Ethernet

• Blink: Connected to Ethernet

16 Channel

960h & 8 / 16 Channel SDI

KEYS PTZ KEY

▲, ▼, ◄, ►

• Control Pan/Tilt rotation of up/down/left/right in PTZ mode

1 ~ 16

• Camera select keys : (4/8/16 channel DVR)

DISPLAY

• Select 1/4/9/16 channel display

SEQUENCE

• Channel sequence mode on/off (Main Monitor)

ARCHIVE

• Copy video data into the external storage device

FREEZE

• Screen freeze mode on/off

EVENT

• System Log display on/off

EMERGENCY

• Emergency recording on/off

PTZ

• Pan/Tilt control mode on/off

AUDIO/ESC

• Audio on/off (Viewing/Playback)

• Select audio channel: Press AUDIO key and then channel key

• ESC

960H & SDI DVR

Description

Operating mode

Page

15

Setup mode

•Up/Down/Left/Right
on screen cursor
control

Digital Video Recorder for Ness IQ-

Series

MENU

• Enter the Main Menu (Setup mode)

PLAY.PAUSE

• Viewing

from the last one minute) •

• Zoom

SEARCH

• Video search mode on/off

• Zoom

REW

•

Fast backward playback (changes up to x128 with each

• Focus Near in PTZ mode

FF

•

Fast forward playback (changes up to x128 with each press)

• Focus Far in PTZ mode

BACKWARD

• Frame backward playback

• Save Preset in PTZ mode

FORWARD

• Frame forward playback

• Go to Preset in PTZ mode

Power LED

(Red)

• Light off: DVR off

• Light on: DVR on

HDD LED

(Green)

• Light off: Stop recording

• Blink : Recording/Playback modes (HDD Access), Archive in operation

Network LED

(Yellow)

• Light off: failed to connect to Ethernet

• Blink: Connected to Ethernet

2.2

Camera Select Keys for 16 Channel

16 channel

960H & 8 / 16 Channel SDI



Below shows how to select camera channel for 4/8/16channel DVR

 Below

shows how to select camera channel for 4 channel DVR

- Select Camera No. 1~4



Below shows how to select camera channel for 8 channel DVR

- Select Camera No. 1~8



Below shows how to select camera channel for 16hannel DVR

- Select Camera No. 11~16: press

2.3 Front Panel

4 / 8 Channel 960h and 4 Channel SDI

DVR

16 Channel

960H & 8 / 16 Channel SDI

960H & SDI DVR

mode: Instant playback (playback the recorded video

Playback mode: 1X PLAY/PAUSE

-Out on PTZ mode

-In on PTZ mode

960H & 8 / 16 Channel SDI

key and use 1~6 direction key

(Compact Housing)

DVR (19” Rack Mount housing)

Page

16

press)

DVR

Digital Video Recorder for Ness IQ-

Series

2.4

Using a Remote Controller



Usage of a remote controller is same as the front panel



Follow the procedure below when using the remote controller for multi DVRs.

①

Check System ID (e.g., between 1 and 255) of the DVR that wish to use.

-

(SETUP>SYSTEM>Information>Status>System ID).

②

Holding up the remote controller to face towards the DVR and press the System ID numbers one by one, while pressing

ID button on the remote controller. Note that the System ID is a

- (e.g.: If System ID is 3, press 10>10

>

2.5 Using a Mouse



Mouse provides an easier access to adjustment. Refer to below for proper use.



Left mouse button functions the same as

 Right mous

e button displays the following “Function keys” on screen.



Click Search menu at “Function Keys” the same as

menu will appear on screen.

4 / 8 Channel 960H & 4 Channel SDI

Name of Key

Function

Display

Change display mode

Sequence

Display each channel sequentially

Spot

Use spot monitor

Freeze

Freeze on live/recorded display

PIP

Picture in Picture function

PTZ

En/Disable PTZ control

16 Channel

960H & 8 / 16 Channel SDI

Name of Key

Function

Display

Same as front key

Sequence

Same as front key

Spot

Same as front key

Freeze

Same as front key

PIP

Same as front key

PTZ

Same as front key

960H & SDI DVR

keys.

3-digit number. Button ‘

10

3 buttons in sequence while pressing the ID button)

Enter ( ) key on the front panel of DVR.

Search

key on the front panel of DVR. Press the button, then the Search

Name of Key

Event

Display System Log

Search

Enter Search Mode

Setup

Enter Setup

Emergency

Activate

Emergency record

Shutdown

Pre-

step before Power off

(SETUP>SYSTEM>Shutdown)

Cancel

Cancel Function key menu

Name of Key

Event

Same as front key (indicate System Log)

Search

One-

touch playback (same function with

(PLAY/PAUSE)

Setup

Same as front key

Emergency

Same as front

key

Shutdown

Pre-

step before Power off

(SETUP>SYSTEM>Shutdown)

Cancel

Cancel Function key menu

Page

17

’ functions the same as ‘0’.

Function

Function

Digital Video Recorder for Ness IQ-

Series

2.6 Screen Icon

Icon

Description

Continuous recording mode

Event recording mode
(Motion)
Event recording mode
(Alarm In)

In recording

PTZ registration / PTZ mode

Setup in HDD No Overwrite mode

(HDD Full)

960H & SDI DVR

Icon

Description

In Audio recording

16

CMS access indication/ No. of accesses

(up to 16)

In channel sequencing

Lock

Setup in HDD Overwrite mode

Setup in HDD No Overwrite mode

(recording)

Page

18

Digital Video Recorder for Ness IQ-

Series

3.

Setup

3.1 Login / Logout



At the default setting of DVR, user has to input the password to enter the set up menu.



Please press SETUP key to enter the setup menu and the following screen will appear.



In order to use all functions and privileges, log

 Default Password is “1111”.


At Setup>System>Account, Administrator should set a user rights depending on each user separately in “Login Settings”.

 After login successfully, following scree

n will appear:

 Recording continues during setup.
 Main menu consists of 5 sub menus.

- (

SYSTEM / DISPLAY / DEVICES / RECORD / LINK



There is no factory default in the case of passwords.=> Factory default function cannot be applied to passwords.

 To escape f

rom the setup menu, please click (

 Please choose ‘OK’ to log out.
 User may select the Main menu with

,

under the Main menu.

NOTE

Press AUDIO/ESC in the setup screen. It operates like CANCEL (ESC).

It will not operate in the live or playback mode but only in the setup menu.

960H & SDI DVR

in as ID: admin.

)





 )

SYSTEM>Exit on the screen. Then, the following dialogue box will appear.

direction keys or mouse click. Please click (

) the submenu to choose

Page

19

the one

Digital Video Recorder for Ness IQ-

Series

3.2 SYSTEM

3.2.1 Information

 Please click ( )

SYSTEM>Information and the

Site Description

 Decide on a name of DVR.
 Please click ( ) keyboard icon on

Site Description frame and the following virtual keyboard will appear.

 Please click (

) desired letters (characters) on the virtual keyboard to input.

①

Use to erase one character every time.

②

Use to erase the whole sentence.



Please choose ‘OK’ to confirm the input and choose ‘Cancel’ to cancel.

System ID

 Control DVRs

by one remote controller by setting DVR IDs.

 Please click ( )

▲, ▼ direction keys on the right

number between 1 and 255.

 While pressing (+) or (-

) button, the System ID value increases

Language

 Please click (

) Language frame to choose desired language and press

Setup

 Default: Click (

) Default frame to restore all setup values of menus to factory default settings.

is not initialized.

Status

960H & SDI DVR

following screen will appear.

-

hand side of the System ID frame to set the ID of DVR.

or decreases by 10 units.

( ) key again.

Page

20

Take any whole

Please note that System Log

Digital Video Recorder for Ness IQ-

Series

NOTE

This has a different function from Factory Reset Switch on the back panel of DVR in that System Log is not initialized.

 Import:

Copy the Menu setup stored in USB memory stick into DVR. Please plug in the memory stick and then click (

Import.

 Export:

Store the Menu setup of DVR in USB memory stick. Please plug in the memory stick and then click (

 When user is on Defau

lt, Import or Export process, a message box will ask the progress and click the confirmation icon, then

a message box will show whether its success or failure.

System Log

 Export:

Store the System Log contents in USB memory stick. Please plug in the memory



When user is on Default, Import or Export process, a message box will ask

message box will show whether its

success



When user complete Status data input, please click

Version Upgrade

 User may upgrade DVR software.


Please follow the Upgrade procedure below.

① Plug USB memory stick

having upgrade file into DVR.

② Click (

) Load frame. Then, software version stored in the USB will appear on the left

③ Click (

) Start frame to start the upgrade.

④

When the upgrade is completed, a dialogue box pops up. Please choose ‘OK’ and DVR

NOTE

Upgrade file must be placed without folder. Otherwise SYSTEM will not

CAUTION

DO NOT UPGRADE UNTIL A HARD DISK DRIVE

CAUTION

PLUGGING OUT USB DEVICE OR FORCED POWER

CAUTION

REMOTE UPGRADING WILL CAUSE SYSTEM TO CHANGE ALL THE SETTINGS TO DEFAULT EXCEPT NETWORK SETTING.

Version

960H & SDI DVR

stick and then click (

to proceed

and click the confirmation icon,

ful or failed.

(

) Version and the following screen will appear.

-

hand side.

will auto

be able to recognize the file.

IS INSTALLED

. MAKE SURE TO UPGRADE WHEN HDD IS IN PROPER OPERATION.

-OFF DURING VERSION UPGRADE

MAY CAUSE PERMANENT DAMAGE.

Page

21





 )





 ) Export.





 ) Export.

then a

-reboot.

Digital Video Recorder for Ness IQ-

Series



When user completes Version input, please click



The screen shows start time and end time of recorded data.

Overwrite Setting

 Click ( ) Overwrite Setting button

and the following screen will appear.



User shall designate the total recording days from 1 day to 30 days and unlimited.



User may set for beeping or notifying messages that notify the used percentage of disk.



Check Disk Overwrite and user may activate

-

This function makes restart the recording from the beginning when the HDD is full. The previous recorded data will be

erased from the first one. Following icon will display in bottom of live mode

① Uncheck (□) Disk Overwrite, reco

rding will stop automatically when the HDD is full.

② At no Overwrite mode,

icon will appear when HDD capacity is full that indicates the recording has stopped and,

icon

will appear while the recording is going on.

③

If user changes this setting, the warning message will appear. Then click

the setting.

 If user checks (

) Disk full notify item, the warning message will appear as the used amount of disk.

① Used

- User may set th

e certain value of HDD usage for notification. It will notify at that point. The values are from 50 ~ 100%.

② Alarm-Out

- The Alarm-

out will happen at the used amount of HDD which is specified at Used.

③ Beep

- Check (

), the warning sound will happen at the used

④ Blink Message

- Check (

), the warning message “Disk Used(xx%)!” will appear on the OSD.

Record

960H & SDI DVR

(

) Record. Then, the following screen will appear.

the overwrite function.

. .

(

) “confirmation” button and user may change

amount of HDD which is specified at Used.

Page

22

Digital Video Recorder for Ness IQ-

Series

CAUTION

IF USER USES “Rec Days”

FUNCTION, DVR WILL STORE ONLY THE DAYS THAT SPECIFIED BY USER. PLEASE

BEWARE OF DATA LOSS DUE TO “

Rec Days

NOTE

Notify setting does not affect saving the recorded data. It only gives notification and keep recording until hard disk is ful

NOTE

For more specific setting about Alarm-

out, use Setup>DEVICES>Alarm Out.

Clear All Data



Use to delete or purge all normal recorded data from database. Please follow the procedure below.

① Click ( ) Clear All Data frame.
② When a dialogue box asking

“Remove All Data?” shows, choose ‘OK’.

③

Then, Progress window will appear and the process starts.

④

When all data are deleted, a dialogue box asking “Are you sure to remove log?” will pop up.

⑤

Choose ‘OK’ to delete all the recorded data as well as System Log.



When user finished all the necessary inputs to SYSTEM menu, please click (

screen.

NOTE

This might take a while to completely delete all data

CAUTION

DELETED DATA CANNOT BE RESTORED

.

3.2.2 Admin

 Please click ( )

SYSTEM>Admin and the following screen will appear.

Date



This menu will allow user to adjust the settings.



Please follow the procedure below for time adjustment.

① Click ( )

items (Y, M, D) to change. A designated item will be highlighted in a box (Y: Year, M: Month and D:

② Adjust the number by clicking ( )

▲, ▼

③

Repeat the same procedure to change Y, M and D.

Time



This menu will allow user to adjust the current time. The adjustment procedure is same as of Date.

Date / Time

960H & SDI DVR

” FUNCTION.







) ‘OK’ on the bottom to go back to SETUP

, and DVR will reboot after the data is cleared.

-hand side.

Page

23

l.

Date).

Digital Video Recorder for Ness IQ-

Series

CAUTION

IF ADJUSTED

DATE/TIME IS PRIOR TO RECORDED DATA, DATA AFTER NEW DATE/TIME MAY BE ERASED.

CAUTION

ANY CHANGE IN DATE/TIME IS IMMEDIATELY APPLIED ON VIEWING SCREEN (LIVE), BUT THE DATE/TIME WHEN THE RECORDING

WAS DONE IS NOT CHANGED. MAKE SURE TO REBOOT DVR AFTER

SHUTDOWN (SYSTEM>Shutdown) BEFORE REBOOT.

Time Zone

 Please click (

) Time Zone frame to see the list of nations and choose one.

 Click (

) a check box next to Use Daylight Saving Time. When user dwells in

 If DST is observed, please click (

) Period and the following screen will appear.



Adjust the dates of beginning (Begin) and end (End) of DST by ‘Month/Week/Weekday’.

 Click ( )

the numbers in ‘Month/Week/Weekday’ for adjustment.

 Choose ‘OK’ to confirm the setting.

Date Format



Set date indication format. Please click (

Time Format



Set time indication format. Please click (





When user complete Date/Time input, please click



This menu is for accurate setting of time of day clock in DVR.

 User may check 

only one of Run as Server and Use NTP.

- Run as Server:

NTP cannot be used in a non

as Server functions as Time Server.

- Use NTP:

Connect to Internet to synchronize DVR clock with Network Time Server’s clock.

 When user comple

tes NTP input, please click

NTP

960H & SDI DVR

CHANGING THE DATE/TIME. DO NOT FORGET TO EXECUTE

a region of DST area, please check it (i.e.





 ) Date Format frame to select a format from the list.

) Time Format frame to select a format from the list.

(

) NTP and the following screen will appear.

-

networked environment (Intranet environment). In this case, DVR with Run

( ) to save the setup.

Page

24

).

Digital Video Recorder for Ness IQ-

Series

NTP Server

 Click ( ) keyboard icon in

NTP Server frame and the virtual keyboard will appear. Input IP address of NTP server.

NOTE

“Use NTP” function connected to the

Time zone

NOTE

Currently used NTP is administered by pool.ntp.org and its IP address is 65.23.154.62. However, users are allowed to use IP a

NTP site.

Interval

 Set clock-update-interval from NTP

Server. Normally, user can adjust 1 hour up to 24 hours.

System Clock

 Display DVR clock.

Server Clock



Display NTP Server’s clock if Internet is connected to Server Clock. If not displaying, please click (

 When Server Clock is

displayed, please click (



Choose ‘OK’ to confirm the clock synchronization.

 When users click the storage tab,

following screen will appear.

 Set S.M.A.R.T. (Self-

Monitoring Analysis and Reporting Technology) function for HDD format and auto

information. DVD-

RW is not shown here.



Clicking Up and Down button for checking up the status of HDD and

 Using E-

SATA port will allow users to connect up to maximum



When user installs full storage device and DVD

as below:

- 1. Internal SATA 1~4 Ports

- 2. External SATA 1

- 3. DVD-RW

Format

 User must format when:

- install new HDD

- add another HDD

- replace HDD

- move HDD (change installation port)

- remove HDD

 Click (

) Add/Remove frame in Format column and choose ‘OK’ on the dialogue box to start

Storage

960H & SDI DVR

, user should set the Time

zone correctly to operate the NTP function properly.





 ) Sync button

to synchronize NTP Server’s clock with DVR clock.

DVD-RW devices.

8 HDD +1 DVD-RW. (

16 Channel

-RW including two e-

SATA storage, then following procedures will be listed

formatting.

Page

25

ddress of any





 ) Connect button.

-display of HDD

)

Digital Video Recorder for Ness IQ-

Series

 Following format, DVR will auto-

reboot. If there are more than 2 HDDs, please formats each of HDDs. DVR will auto

when all the HDDs are formatted.

 If the format changes to ‘---

‘after reboot, it means formatting has been properly done.

CAUTION

EXECUTE REMOVE PROCEDURE EVEN WHEN USER REMOVE PREVIOUSLY INSTALLED HDD. THE REMOVE PROCEDURE IS THE

SAME AS THE FORMAT PROCEDURE DESCRIBED ABOVE.

S.M.A.R.T



Click the frame on S.M.A.R.T column and temperature and HDD damage will show.

S.M.A.R.T Setup

 Please click ( )

S.M.A.R.T Setup and the following screen will appear.

 Check the square box 

next to Use On. Through S.M.A.R.T function, make alarm message, indicating HDD damage, will

show.

 Check 

Beep; it will give the alarm sound, indicating HDD damage, as the SMART setup.

 Check 

Blink Message, the alarm message will blink on the OSD, as the SMART setup.



If “Use on” box is unchecked, Beep, Blink Message will be unchecked automatically. Only when

can set Beep, Blink Message function.

 Click (

) Inspection Time frame to set inspection time.



Click Check by frame to select inspection interval.



Last Check Time: show the time of the last inspection.

 Check  Alarm out :

user can set the alarm out, when S.M.A.R.T

 Duration of alarm out operating time

can adjust on

 Clicking ( ) ▲, ▼ direction buttons

on the right

 Click ( )

▲, ▼ direction buttons on the right

HDD used in DVR. In general, it is 55℃

℃℃

℃

.

 Click ( ) ▲, ▼ directi

on buttons on the right

(%). HDD is a very crucial element for DVR recording, so set the permissible level within 1% to 2% to assure maximum

safety.

- While pressing (+) or (-) button

on the rightmost side of Temperature or HDD Damage item, a target value increases or

decreases by 10 units.

 Check 

Notification : user can send the email notification to registered email address, when S.M.A.R.T function detects

Abnormal symptoms from HDD.

 Choose ‘OK’ to confirm the setting.

960H & SDI DVR

function detects

Abnormal symptoms

DEVICES>Alarm Out setup

section (please refer 4.4.5).

-hand of alarm-

out frame to select the device for alarm out.

-

hand side of Temperature frame to adjust to maximum temperature for the

-

hand side of HDD Damage frame to set the permissible level of HDD damage

Page

26

-reboot

“Use on” is checked, user

from HDD.

Digital Video Recorder for Ness IQ-

Series

3.2.3 Account

 Please click ( ) S

YSTEM>Account and the following screen will appear.

 Please click ( )

New Group and the following screen will appear.

 Click ( ) keyboard icon on the right-

hand side of

desired characters (up to

8 characteristics



Do provisioning for Group Name by selectively checking

and Shut Down).

 Choose ‘OK’ to confirm the setting.

 Please click ( )

Login Settings and the following screen will appear.



Selectively enable password protection for important operations (Setup, Search, Network, Archiving and Shut Down).

 Please check 

the operations that wish to enable password protection.

 Choose ‘OK’ to confirm the setting.

Login Setting

New Group

960H & SDI DVR

Group Name frame. Then, the virtual keyboard will show. Please click (

) on the virtual keyboard.

 some of the following items (

Setup, Search, Network, Archiving

Page

27





 )

Digital Video Recorder for Ness IQ-

Series

CAUTION

USER WILL NOT BE ASKED TO ENTER THE

 Please click ( )

New User and the following screen will appear.

 Click ( ) the keyboard icon on the right

-

characteristics (up to 8 characteristics) on the virtual keyboard.

 Input Password and Confirm.


Choose ‘OK’ to confirm the setting. Then, lists of Group and User will show as follows.

 Click ( ) 

to delete the set Group or User.

 User may create up to 8

Groups and 8 Users

 Choose ‘OK’ to confirm the setting.

Password Resetting



Click ID on User column. The following screen will appear.

 This is a screen for password resetting.


Input password by clicking the keyboard icon on the right

New User

960H & SDI DVR

PASSWORD FOR OPERATION(S) WHEN

PASSWORD PROTECTION IS NOT

hand side of User Name frame and the virtual keyboard will appear. Click desired

per Group.

-hand side of the frame.

Page

28

ACTIVATED.

Digital Video Recorder for Ness IQ-

Series

 Use

key if wish to erase password on keyboard.

3.2.4 System Log

 Please click ( )

SYSTEM>System Log and the following screen will appear.

 System Log

displays diverse events as below events by specifying the user account that actually

- Setup (Menu) Enter/Exit

- Playback Mode Enter/Exit

- Network Access Enter/Exit

- Archive Success/Fail

- System Start/shut down

- S.M.A.R.T. Check

- NTP Sync/ Server Success/Fail

- Send E-mail Success/Fail

- HDD Format Success/Fail

- Data clear Success/Fail

- USB Upgrade Success/Fail

- DVR Setup Change by Remote

- Before/After Time Adjust

- Video loss



System Log removal procedure is as follows:

-

Execute Clear All Data in SYSTEM>Information>Record and choose ‘OK’ on the popup dialogue box. Please note that

normal recorded video data are deleted from database.

-

Press Factory Reset Switch on the back panel. Please note that the entire menu setup is also defaulted.

3.2.5 Exit

 Please click ( )

SYSTEM>Exit and choose ‘OK’ on the popup dialogue box to exit from t

CAUTION

ANY CHANGES MADE IN SETUP WILL BE

APPLIED AFTER EXIT.

960H & SDI DVR

he setting.

Page

29

has accessed the DVR.

all

Digital Video Recorder for Ness IQ-

Series

3.2.6 Shutdown



Shutdown is a function to help user safely turn the DVR off. Please use the proper shut down procedure to avoid damaging

to our DVR system. Do not remove the power

 Click ( )

SYSTEM>Shutdown and then choose ‘OK’ on the dialogue box to confirm.



When user select Shutdown menu, the OSD menu on the screen disappears.



Reboot the DVR after Shutdown. Turn off the DVR and wait for 5 seconds before restart.

CAUTION

DO NOT TURN DVR OFF WITHOUT USING THE PROPER SHUT DOWN PROCEDURE. OTHERWISE, IT MAY CAUSE DAMAGE TO

DVR. ALWAYS REMOVE THE POWER AFTER SHUT DOWN.

3.3 DISPLAY

 Please click ( )

DISPLAY and the following screen will appear.

3.3.1 OSD

 Please click ( )

DISPLAY>OSD and the following screen will appear.



The OSD menu will allow user to configure full features (i.e., on/off every letter and icon) displayed on the screen.



Letters and icons are divided under System and Camera categories. If click

960H & SDI DVR

during shut down.

( )

‘All’, all items are on/off at once.

Page

30

Digital Video Recorder for Ness IQ-

Series

OSD Margin



The OSD Margin menu will allow user to adjust the position of OSD (letters) on the monitor. Use it when some of letters are

dropped out and invisible on the monitor.



Adjust Horizontal to change margin betw

0 and 50

, with a larger number representing greater margin.



Adjust Vertical to change margin between both ends of the monitor on vert 130.

 Vertical side and OSD Margin range i

s between

 While pressing (+) or (-

) button, a target value increases or decreases by 10 units.

De-Interlace



This function changes playback display into Progressive Scan or Interlace Scan. Check

display as the Progressive Scan and shows the better picture quality.

3.3.2 Main Monitor

 Please click ( )

DISPLAY>Main Monitor and the following screen will appear.



The Main Monitor menu will allow user to adjust channel



Adjust interval for ‘Full screen sequencing’.

 Check 

check box next to the camera that wish to include in sequencing. Any camera with unchecked check box will be

excluded from channel sequencing.



Adjust the rotation interval of camera by clicking Dwell column. The rotation interval changes to

by each press.

 Use only with 8 / 16 channel DVRs.


Adjust interval for ‘X4 Split Screen sequencing’.

 Check 

check box next to the camera that wish to include in sequenci

excluded from channel sequencing.



Adjust the rotation interval of camera by clicking Dwell column. The rotation interval changes to

by each press.

 ‘4 Split Screen sequencing’ is disabl

ed in the following modes.

- 8 channel DVR: 3x3 Mode

- 16 channel DVR: 4x4 Mode

Quad Seq

Full Seq

960H & SDI DVR

een both ends of the monitor on horizontal side and OSD. Margin range is between

0 and 50

, with a larger number representing greater margin.

(

) De

sequencing interval of Main monitor.

ng. Any camera with unchecked check box will be

Page

31

-Interlace, then frame will

3>5>10>15>30>60 seconds

3>5>10>15>30>60 seconds

Digital Video Recorder for Ness IQ-

Series

 Use only with 16 channel DVR.


Adjust interval for ‘X9 Split Screen sequencing’.

 Check 

check box next to the camera that wish to include in sequencing. Any camera with unchecked check box will be

excluded from channel sequencing.



Adjust the rotation interval of camera by clicking Dwell column. The rotation interval changes to

by each press.



‘9 Split Screen sequencing’ is disabled in 4X4 Mode.

3.3.3 Multi Spot

 This connection supports multi-

channel display (1/4/9/16) on spot monitor depending on its channels(4/8/16)



Click [MS] button on the menu bar to select the Multi Spot.



Click [1/4/9/16] button to select the multi channel split display mode

 Please click ( )

DISPLAY>Multi Spot and the following screen will appear.



The Multi Spot menu will allow user to adjust channel sequencing interval of



Adjust interval for ‘Full screen sequencing’.

 Check 

check box next to the camera that wish to include in sequencing. Any camera with unchecked check box will be

excluded from channel sequencing.



Adjust the rotation interval of camera by clicking Dwell column. The rotation interval changes to

by each press.

 Use only with 8 / 16 channel DVRs.
 Adjust

interval for ‘X4 Split Screen sequencing’.

 Check 

check box next to the camera that wish to include in sequencing. Any camera with unchecked check box will be

excluded from channel sequencing.



Adjust the rotation interval of camera by clicking Dwell column. The rotation interval changes to

by each press.



‘4 Split Screen sequencing’ is disabled in the following modes.

- 8 channel DVR: 3x3 Mode

- 16 channel DVR: 4x4 Mode

Quad Seq

Full Seq

X9 Seq

960H & SDI DVR

.

Spot monitor.

Page

32

3>5>10>15>30>60 seconds

.

3>5>10>15>30>60 seconds

3>5>10>15>30>60 seconds

Digital Video Recorder for Ness IQ-

Series

 Use only with 16 channel DVR.


Adjust interval for ‘X9 Split Screen sequencing’.

 Check 

check box next to the camera that wish to include in sequencing. Any camera with unchecked check box will be

excluded from channel sequencing.



Adjust the rotation interval of camera by clicking Dwell column. The rotation interval changes to

by each press.



‘9 Split Screen sequencing’ is disabled in 4X4 Mode.

3.4 DEVICES

 Please click ( )

DEVICES and the following screen will appear.

3.4.1 Network

 Please click ( )

DEVICES>Network and the following screen will show.

X9 Seq

960H & SDI DVR

Page

33

3>5>10>15>30>60 seconds

Digital Video Recorder for Ness IQ-

Series

Network Type

 Please click ( ) Network Type.

When you

IP).



In Static, user must manually set the static IP

-

Set IP Address, Subnet Mask and Gateway. Please ask your network administrator for more details.

- To input address, please click (

) and execute the keyboard icon on the right

 In DHCP, IP Address, Subnet Mask,

Gateway

DNS Server



When user set Network Type to DHCP, DNS server will be inputted automatically.



When user set Network Type to Static, please click (

manually input the address.

CAUTION

NOTE THAT DNS SERVER ADDRESS IS IP ADDRESS OF YOUR COMMUNICATIONS COMPANY NAME SERVER PROVIDING

INTERNET SERVICE. IT IS NOT THE IP ADDRESS OF DDNS SERVICE SITE.

 Please click (

) DDNS and the following screen will appear.



‘Floating IP system’, although being predominantly used over Internet, is very inconvenient for users because its address

varies every time when user

access. The best alternative is DDNS (Dynamic Domain Naming System) which uses name

(domain name) instead of IP address (numbers). DDNS automatically recognizes ever changing, floating IP addresses, so it

will allow easy Internet access.

 Dvrdormain.com

- Check  a checkbox of

Dvrdomain.com

- As for DDNS Server, D

vrdomain.com will be showing as default.

- As for Port, 95 will be shown as

default. If ‘95’ is unable, please consult with a

DDNS

LAN

960H & SDI DVR

click ( ) the button

, it changes alternately to Static (fixed IP) and DHCP (floating

address for use.

-

hand side of each frame.

and DNS Server will have input automatically.





 ) the keyboard icon on the right-

hand side of DNS Server

to use Dvrdomain.com Server.

service provider

Page

34

frame and

.

Digital Video Recorder for Ness IQ-

Series

- When user press Get Domain

Name button, Domain Name and MAC Address value will automatically display after 10

seconds.

- Choose ‘OK’ to confirm the setting.

 3rd Party

- Check  a checkbox of 3rd Party

to use

- As for DDNS Server,

dyndns.org will be showing as

-

As for Domain Name, user has to input the Domain Name given from the selected DDNS Server.

-

As for ID and Pass word, use the user ID and Password to log in to the

- Click “Run ddns service”

to start mapping from DVR to DDNS Server.

- Choose ‘OK’ to confirm the setting.

NOTE

User must join ‘dyndns.org’ or’ no-ip.com’

prior to using it as DDNS server. Please check corresponding website for more inf

 Please click ( )

Port and the following screen will appear.

Port

960H & SDI DVR

dyndns.org or no-ip.com Server.

default. No-

ip.com can be selected by clicking the arrow.

selected DDNS Server.

Page

35

ormation.

Digital Video Recorder for Ness IQ-

Series

 Network Throat Control

is for setting an average transfer speed.



Please choose the suitable speed according to the users’ network environment.

 If users

want to use dual streaming, please click on the check box beside the “Enable Dual Streaming”. If not, please

uncheck the check box.



There are total of 14 different network throat controls users may choose. (bps: bit per second) 26 kbps, 128 kbps, 256 kbps,

512 kbps, 1 Mbps, 2 Mbps, 4 Mbps, 8 Mbps, 10 Mbps, 20 Mbps, 40 Mbps, 80 Mbps, 100 Mbps, Unlimited(default).

- Ethernet support Max. 1000Mbps.



Network video transmission speed and quality can be configured by pressing “Frames” and “Quality” buttons as follow

- F

rames 1, 2, 3, 4, 5, 6, 12.5, 25 frames for PAL

-

Quality : Std. 1, Std. 2, Std. 3, Std. 4 (standard), High 1, High 2, High 3, Super 1, Super 2, Super 3



The Port Number Setup menu will allow users to set Administrator and Port Number for Video/Audio and



The Port Number Setup menu has two selections of “Register UPNP” or “Unregister UPNP”.

 Click ( )

“Register UPNP” for automatic port forwarding.

 Click ( )

“Unregister UPNP” to do port forwarding manually.

 For Port Number Setup, please get an

approval of the network administrator in connection with CMS program.

 Port number

- Administrator: 5000~65535

- Video / Audio: 5000~65535

- Web: 1~65535

 Choose ‘OK’ to confirm the setting.

CAUTION

PLEASE CHECK THE ROUTER FOR UPNP SUPPORTABILITY BEFORE START

CAUTION

ONCE PORT NUMBERS

ARE CHANGED, IT MUST BE CHANGED THE

PROGRAM AS WELL.

 Please click (

) Notification and the following screen will appear.

 The Notification menu allows users

to send the message of the Event

 Click ( ) the keyboard icon on the right

-

E-Mail address. E-

Mail address should contain @.

 Click ( ) the keyboard icon on the right

-

register the SMTP Server.

SMTP server can be set up by the users to have own SMTP server on their site.

 Click ( ) the keyboard icon on the right

-

an ID to the sender mail server (e.g., tony123).

 If users want

to use dvrdomain.com which is offered by manufacturer instead of own SMTP serv

box (use dvrdomain.com).

Notification

960H & SDI DVR

USING THE UPNP FEATURE.

PORT NUMBERS

OF CMS (Central Monitoring Station)

occurred in DVR via E-

Mail.

hand side of Add E-

Mail frame and the virtual keyboard will appear. Please register

hand side of SMTP Server frame and the virtual keyboa

hand side of Sender ID frame and the virtual keyboard will appear. Please register

Page

36

s.

Web Port.

rd will appear. Please

er, please click on the check

Digital Video Recorder for Ness IQ-

Series

 Default number

of SMPT port is 25. Please note that some particular areas have restriction on the default port. If so, port

number 2525 and 587 can be

replaceable

 When an event occurs, users can send

an email to a designated mail address by clicking

be transmitted. Users

may select one of JPEG, VIDEO CLIP

duration of time for recoded data in d

uration

CAUTION

ACCORDING TO THE VARIOUS

LOCAL CONDITIONS; SSL EMAIL SERVERS MAY NOT WORK CORRECTLY WITH THIS

SO PLEASE INACTIVATE THE SSL FEATURE IN THE SERVER SETUP. NOTE THAT SOME SERVER MAY NOT HAVE THIS

INACTIVATE FEATURE

CAUTION

DEPENDING ON THE VARIOUS LOCAL CONDITIONS, SOME

FUNCTION.

3.4.2 Camera / PTZ

 Please click ( )

DEVICES>Camera/PTZ and the following screen will appear.

 Click ( ) the keyboard icon on the right

-

register titles of cameras.

 If a check box is checked on

No column, a video of the corresponding camera is recorded and displayed on the monitor.

However, if us

er does not check the checkbox, both recording and monitor display stop. Then, DVR picture, instead of a

recorded video, will be displayed on the monitor.

CAUTION

WHEN USER EXCLUDES A CORRESPONDING CAMERA VIDEO FROM RECORDING AND MONITOR DISPLAY (CHECK A CHECK BOX



), MAKE SURE CHANNELS OF LARGE NUMBERS ARE EXCLUDED FIRST.

 If a check box is checked 

on Covert column, a video is recorded but is not displayed on the monitor.

 Click (

) each frame on PTZ column to select PTZ protocols connected to a corresponding camera.

NOTE

When using RS-485 over Coax

, user can select any protocol from the Protocol list other than

RS-485 over Coax will not work.

 Click (

) each frame on Set to set PTZ Settings connected to a corresponding camera.

960H & SDI DVR

.

a

ttach button and selecting

and

None. In case of transmitting VIDEO CLIP

menu. (e.g., 1 sec, 3 sec, 5 sec).

E-

MAIL SERVERES MAY NOT WORK PROPERLY WITH THIS

hand side of each frame on Title column and the virtual keyboard will appear. Then,

‘NONE’. If ‘

NONE

Page

37

data to

data, set the

FUNCTION. IF

’ is selected then

Digital Video Recorder for Ness IQ-

Series

 If users click (Default), proper

number of selected PTZ will appear automatically. Please choose ‘OK’ to confirm the setting.



Menu, Tour and Pattern help user to use OSD function of PTZ camera.

-

PTZ camera itself supports OSD menu, use the setup value to more easily enter and use the OSD

-

If OSD enter command is 95 + PSET for example, designate 95 for Menu item,

-

If shortcut key to use Tour function is 71 ~79 + PSET, designate 70 for Tour item and

-

If shortcut key to use Pattern function is 81 ~ 89 + PSET, designate 80 for P

-

The setting information herein is used for PAN/TILT control

-

If click Default, basic setup values are given (i.e., Menu: 95, Tour: 70, Pattern: 80).

-

For further details on setting, please refer to the PTZ camera manu

 Click ( )

▲, ▼ direction buttons on the right

 While pressing (+) or (-

) button, ID increases or decreases by 10 units.

 Choose ‘OK’ to confirm the setting.

3.4.3 Audio

 Please click ( )

DEVICES>Audio and the following screen will appear.



The Audio menu will allow user to choose whether to record Audio.

 When a check box is marked 

on No column, corresponding audio and video

However, if the check box

is not marked



If users check on bind to cam, then the audio and video of same channel will come out.

channel will not come out. I

n addition, this function will e

 Choose ‘OK’ to confirm the setting.

960H & SDI DVR

attern item.

in 5.1.5 (to be described).

al.

-

hand side of the ID column to set ID number (i.e.,

from Linked Camera will be

, audio will not record.

If

not, the audio of unchecked

ffect on live screen.

(The default audio channel is No. 1)

Page

38

menu even in DVR.

0 ~ 9999) of each PTZ.

recorded.

Digital Video Recorder for Ness IQ-

Series

3.4.4 Alarm In

 Please click ( )

DEVICES>Alarm In and the following screen will appear.



The Alarm In menu will allow user to give title and to select the type of

Alarm In Setting

 Click ( ) the keyboard icon on the right

-

please register the title of Alarm input.

 When a check box is marked 

on No column, a correspondin

check box, the operation stops.

 Click ( ) each frame on T

ype column to select type of a corresponding Alarm input.

- NO: contact is normally open

(Normally open)

- NC: contact is normally closed

(Normally closed)



User may change the type of all Alarm input at a time by clicking the Type box on the menu tab.

 Choose ‘OK’ to confirm setting.

Alarm Schedule



Users are able to schedule the Alarm In deactivation period.

 Click ‘Alarm Schedule’ and the

following screen will appear.

 Sel

ect the Alarm Input(s) to apply alarm in

 Select the Hours to deactivate

the alarm in sensor.

 Choose ‘OK’ to confirm setting.

3.4.5 Alarm Out

 Please click ( ) DEVICES>Alarm

Out and the following screen will appear.



The Alarm Out menu will allow user to give title and to select the type and duration of Alarm output.

960H & SDI DVR

Alarm input.

hand side of each frame on

Title column and the virtual keyboard will appear. Then,

g Alarm starts operating. However, if user does not check the

sensor deactivation according to Alarm schedule.

Page

39

Digital Video Recorder for Ness IQ-

Series

 Click ( ) the keyboard icon on the right

-

please register the title of Alarm output.

 When a check box is marked 

on No column, a corresponding Alarm output starts operating. However, if user does not

check the check box, the operation stops.

 Click ( ) each frame on Type colum

n to select type of a corresponding Alarm output.

- NO: contact is normally open

(Normally open)

- NC: contact is normally closed

(Normally closed)



User may change the type and duration of all Alarm output at a time by clicking the Type and Duration box on the

 Choose ‘OK’ to confirm setting.

3.4.6 Serial In

NOTE

Please refer to “14 Serial In”.

3.5 RECORD

 Please click ( )

RECORD and the following screen will appear.

960H & SDI DVR

hand side of each frame on

Title column and the virtual keyboard

Page

40

will appear. Then,

menu tab.

Digital Video Recorder for Ness IQ-

Series

3.5.1 Setting

 Please click ( )

RECORD>Settings and the following screen will appear.



There are three kinds of recording mode.

- Continuous: record continuously.

- Event:

record only when Sensor or Motion calls.

- Emergency: record when press

EMERGENCY

-



The Continuous menu will allow user to set recording mode.



Each frame on Title column shows camera title registered in DEVICES>Camera/PTZ. User cannot change camera titles

here.

 Click ( ) each frame on

Resolution column

of 360x240(288), 720x240(288),

720x480(576), 960x480(576)

 Click ( ) each frame on

Frames column to select recording rate of a corresponding camera. Recording rate varies by

ca

mera. Below lists the maximum recording rate of each camera.

960H Models

NTSC(PAL)

360x240 (360x288)

4 Channel DVR
8 Channel DVR

16 Channel DVR

SDI Models

360x240 (360x288)

720x240 (720x288)

4 Channel DVR

Max. 30 fps per Channel

Max. 30 fps per Channel

8 Channel DVR

Max. 30 fps per Channel

Max. 30 fps per Channel

16 Channel DVR

Max. 30 fps per Channel

Max. 30 fps per Channel

 Click ( ) each frame on ‘

Quality’ column to select recording quality of a corresponding camera. User may select

recording quality from Super, High,

Std

 Click ( ) each frame on ‘

Duration’ column to select recording duration (i.e.,



User may change the setting values of Resolution, Frames, Quality and Duration at a time by clicking the menu tab.

 Choose ‘OK’ to confirm the setting.

Continuous

960H & SDI DVR

key.

to select recording resolution of a corresponding camera. User may select one

.

720x240 (720x288)

720x480 (720x576)

120 (100) 120 (100)

120 (100)

240 (200) 240 (200) 240

(200)

480 (400) 480 (400)

480 (400)

720x480 (720x576)

1280 x 720

Max. 30 fps per Channel Max. 30

fps per Channel

Max. 30 fps per Channel Max. 15

fps per Channel

Max. 30 fps per Channel Max. 15

fps per Channel

and Low.

10 second ~1

hour

Page

41

960x480 (960x576)

120 (100)
240 (200)
480 (400)

1920 x 1080

Max. 30 fps per Channel
Max. 15 fps per Channel
Max. 15 fps per Channel

its

) of a corresponding camera.

Digital Video Recorder for Ness IQ-

Series

 Please click ( )

Event and the following screen will appear.



The Event menu will allow user to set Event videos.



Each frame on Title column shows camera title registered in DEVICES

here.

 Click ( ) each frame on

Resolution column to select recording resolution of a corresponding camera. User may select one

of

360x240(288), 720x240(288), 720x480(

 Click ( ) each frame on

Frames column to select recording rate of a corresponding camera. Recording rate varies by

camera. Below lists the maximum recording rate of each camera.

960H Models

NTSC(PAL)

360x240 (360x288)

4 Channel DVR
8 Channel DVR

16 Channel DVR

SDI Models

360x240 (360x288)

720x240 (720x288)

4 Channel DVR

Max. 30 fps per Channel

Max. 30 fps per Channel

8 Channel DVR

Max. 30 fps per Channel

Max. 30 fps per Channel

16 Channel DVR

Max. 30 fps per Channel

Max. 30 fps per Channel

 Click ( ) each frame on ‘

Quality’ column to select recording quality of a corresponding camera. User may select

recording quality from Super, High,

Std

 Click ( ) each frame on ‘

Duration’ column to select recording duration (i.e.,



User may change the setting values of Resolution, Frames, Quality and Duration at a time by clicking the menu tab.

 Choose ‘OK’ to confirm the setting.

CAUTION

IF YOU

CONNECT DIFFERENT TYPES OF HD

Event

960H & SDI DVR

>Camera/PTZ. User cannot change camera titles

576), 960x480(576).

720x240 (720x288)

720x480 (720x576)

120 (100) 120 (100)

120 (100)

240 (200) 240 (200)

240 (200)

480 (400) 480 (400)

480 (400)

720x480 (720x576)

1280 x

Max. 30 fps per Channel Max. 30

fps per Channel

Max. 30 fps per Channel Max. 15

fps per Channel

Max. 30 fps per Channel Max. 15

fps per Channel

and Low.

10 second ~ 1

hour

-

SDI SIGNALS WHILE DVR IS OPERATING. IT MAY CAUSE MALFUNCTIONS OF DVR.

Page

42

960x480 (960x576)

120 (100)
240 (200)
480 (400)

720 1920 x 1080

Max. 30 fps per Channel
Max. 15 fps per Channel
Max. 15 fps per Channel

its

) of a corresponding camera.

Digital Video Recorder for Ness IQ-

Series

 Please click ( )

Emergency and the following screen will appear Emergency.



The Emergency menu will allow user to set Emergency videos.



Each frame on Title column shows camera title registered in DEVICES>Camera/PTZ. User

here.

 Click ( ) each frame on

Resolution column to select recording resolution of a corresponding camera. User may select one

of 360x240(288), 720x240(288),

720x480(576), 960x480(576)

 Click ( ) each frame on Frames

column to select recording rate of a corresponding camera. Recording rate varies by

camera. Below lists the maximum recording rate of each camera.


 960H Models

NTSC(PAL)

360x240 (360x288)

4 Channel DVR
8 Channel DVR

16 Channel DVR


 SDI Models

360x240 (360x288)

720x240 (720x288)

4 Channel DVR

Max. 30 fps per Channel

Max. 30 fps per Channel

8 Channel DVR

Max. 30 fps per Channel

Max. 30 fps per Channel

16 Channel DVR

Max. 30 fps per Channel

Max. 30 fps per Channel



 Click ( ) each frame on ‘

Quality’ column to select recording quality of a corresponding camera. User may select

recording quality from Super, High,

Std

 Click ( ) each frame on ‘

Duration’ column to select recording duration (i.e.,



User may change the setting values of Resolution, Frames, Quality and Duration at a time by clicking the menu tab.

 Choose ‘OK’ to confirm the setting.

CAUTION

IF YOU

CONNECT DIFFERENT TYPES OF HD

3.5.2 Schedule

 Please click ( ) RECORD>Schedule.


Each weekday is composed of 24 ‘Time blocks’. Each block represent 1 hour.

 Click ( ) Camera frame to select

Camera No. 1.



Please set the recording mode as follows:

①

Mark a check box the desired recording mode in the schedule (i.e., Continuous, Alarm, Motion and Pre

wants to stop recording, please clear all check boxes.

② Click block, row, column or

all (square box) to register desired recording mode.

Emergency

960H & SDI DVR

may not change camera titles

.

720x240 (720x288)

720x480 (720x576)

120 (100) 120 (100)

120 (100)

240 (200) 240 (200)

240 (200)

480 (400) 480 (400)

480 (400)

720x480 (720x576)

1280 x 720

Max. 30 fps per Channel Max. 30

fps per Channel

Max. 30 fps per Channel Max. 15

fps per Channel

Max. 30 fps per Channel Max. 15

fps per Channel

and Low.

10 second ~ 1

hour

-

SDI SIGNALS WHILE DVR IS OPERATING. IT MAY CAUSE MALFUNCTIONS OF DVR.

Page

43

960x480 (960x576)

120 (100)
240 (200)
480 (400)

1920 x 1080

Max. 30 fps per Channel
Max. 15 fps per Channel
Max. 15 fps per Channel

its

) of a corresponding camera.

Alarm). If user

Digital Video Recorder for Ness IQ-

Series

- Click ( )

a block and only the block will be registered.

- Click ( )

a row (S~H) and the entire row will be registered.

- Click ( )

a column (00~23) and the entire column will be registered.

- Click ( ) a square box (top-

left side between ‘S’ and ‘00’) and all the rows/columns will be registered.



Repeat the procedure for Camera Nos. 2 to 16. If user wants every camera to have the same mode, please click (

to All Camera.

 Below lists symbols of

the respective recording modes.

Continuous
Alarm In
Alarm In / Continuous
Alarm In / Pre Alarm
Motion
Motion / Continuous
Motion / Pre Alarm
Motion / Alarm In
Motion / Alarm In / Continuous
Motion / Alarm In / Pre Alarm

 Choose ‘OK’ to confirm the setting.

NOTE

Holiday (H) registration is done with a separate menu.

3.5.3 Pre Alarm

 Please ( )

RECORD>Pre Alarm and the following will appear.

 Pre Alarm is

effectively used when user selected recording mode by Alarm or Motion.



The Pre Alarm will allow user to check, during playback, the previously recorded video before the record start time.

960H & SDI DVR

Page

44





 ) Copy

Digital Video Recorder for Ness IQ-

Series



Each frame on Title column shows camera title registered in

here.

 Click ( ) each frame on

Resolution column to select recording resolution of a corresponding camera. User may select one

of

360x240(288), 720x240(288), 720x480(576), 960x480(576)

 Click ( ) each frame on

Frames column to select recording rate of a corresponding camera. Recording rate varies by

camera. Below lists the maximum recording rate of each camera.

 960H Models

NTSC(PAL)

360x240 (360x288)

4 Channel DVR
8 Channel DVR

16 Channel DVR

 SDI Models

360x240 (360x288)

720x240 (720x288)

4 Channel DVR

Max. 30 fps per Channel

Max. 30 fps per Channel

8 Channel DVR

Max. 30 fps per Channel

Max. 30 fps per Channel

16 Channel DVR

Max. 30 fps per Channel

Max. 30 fps per Channel

 Click ( ) each frame on ‘

Quality’ column to select recording quality of a corresponding camera. User may select

recording quality from Super, High,

Std

 Click ( ) each frame on ‘

Duration’ column to select recording duration (i.e.,

camera.



User may change the setting values of Resolution, Frames, Quality and Duration at a time by clicking the menu tab.

 Choose ‘OK’ to confirm the setting.

960H & SDI DVR

DEVICES>Camera/PTZ. User cannot change camera titles

.

720x240 (720x288)

720x480 (720x576)

120 (100) 120 (100)

120 (100)

240 (200) 240 (200)

240 (200)

480 (400) 480 (400)

480 (400)

720x480 (720x576)

1280 x 720

Max. 30 fps per Channel Max. 30

fps per Channel

Max. 30 fps per Channel Max. 15

fps per Channel

Max. 30 fps per Channel Max. 15

fps per Channel

and Low.

10 second ~ 10

minute

Page

45

960x480 (960x576)

120 (100)
240 (200)
480 (400)

1920 x 1080

Max. 30 fps per Channel
Max. 15 fps per Channel
Max. 15 fps per Channel

its

) of a corresponding

Digital Video Recorder for Ness IQ-

Series

3.5.4 Motion Detection

 Please click ( )

RECORD>Motion Detection and the following



The Motion Detection menu will allow user to set Motion detection alarm.

 Press SETUP

key (or right mouse button) and the SETUP menu will appear.

 SETUP menu descriptions.

- Camera: select camera for setup.

- Sensitivity: select sensitivity (Low,

Normal

- Reverse Vert:

activate the entire column at the cursor’s position.

- Reverse Horz:

activate the entire row at the cursor’s position.

- Select All: active all blocks.

- Deselect All: deactivate all blocks.

- Copy to All Cameras: The present

channel setup applies to all other cameras. Only when click save button, the changed

setup can be saved.

- Save:

save the new settings and go back to previous menu (page).

- Exit:

ignore the new settings and go back to previous menu (page).

- Cancel: cancel Motion Setup menu.

 Choose ‘OK’ to confirm the setting.

960H & SDI DVR

screen will appear.

and High)

Page

46

Digital Video Recorder for Ness IQ-

Series

3.5.5 Holiday

 Please click ( )

RECORD>Holiday and the following screen will appear.



The Holiday menu will allow user to register holidays. Please follow the registration procedure below.

① Use

arrow buttons in the Month Calendar to select Year and Month of holiday to be registered.

- : search subsequent ‘Year’

- : search previous ‘Year’

- : search subsequent ‘Month’

- : search previous ‘Month’

② Click ( )

on date user need to register as holiday.

③ Click ( )

ADD button and the date just clicked on will be copied to the Schedule frame for registration.

④

If wish to cancel the registration of a certain holiday, please click



Since holidays may vary every year, we

 Choose ‘OK’ to confirm the setting.

3.6 LINK

 Please click ( )

LINK and the following screen will appear.



The LINK menu will allow user to set recording modes of all kinds of alarms (Sensor, Motion Event, Video

Event, etc.), alarm output, e-

mail notification and the like.

960H & SDI DVR



button next to the Schedule frame.

recommend user to update on a regular basis.

Page

47

loss, System

Digital Video Recorder for Ness IQ-

Series

3.6.1 Alarm In

 Please click ( )

LINK>Alarm In and the following screen will appear.

 Select cameras for recording while the

alarm in

notification.

 Link Notification displays E-

mail addresses registered in DEVICES>Network>Notification.



Please follow the setup procedures below.

① Click ( )

Alarm In frame and select Alarm In 1.

②

Select cameras for recording when Alarm In 1 is on. Please check

cameras can be set.

③

Select alarm outputs to be worked when Alarm In 1 is on. Please check

More than two alarm outputs can be set.

④ Select E-

mail addresses for notification when Alarm In 1

than two E-

mail addresses can be set.

⑤ Repeat the abo

ve procedure for Alarm In 2~ Alarm In 16

 Choose ‘OK’ to confirm the setting.

3.6.2 Motion Event

 Please click ( )

LINK>Motion Event and the following screen will appear.

 Select cameras for recording

while the motion sensor is in operation and alarm outputs and set up E

notification.

 Link Notification displays E-

mail addresses registered in DEVICES>Network>Notification.



Please follow the setup procedures below.

① Click ( ) Motion Eve

nt frame and select Motion Event 1.

②

Select cameras for recording when Motion Event 1 is on. Please check

two cameras can be set.

960H & SDI DVR

sensor is in operation and alarm outputs and set up E



a check box under Link Camera. More than two



a check box under Link Alarm Out

is on. Please check 

a check box under Link Notification. More

(Up to 2 4 /8 Channels and

Up to 16 for



a check box under Link Camera. More than

Page

48

-mail addresses for

or R1~2.

16 Channel).

-mail addresses for

Digital Video Recorder for Ness IQ-

Series

③

Select alarm outputs to be worked when Motion Event 1 is on. Please check

R1~2

. More than two alarm outputs can be set.

④ Select E-

mail addresses for notification when Motion Event 1

More than two E-

mail addresses can be set.

⑤ Repeat the

above procedure for Motion Event 2~ Motion Event 16.

 Click ( )

By Duration box to set up the recording duration and prevent recording caused by event.



The duration time can be controlled by previous setting mode:

 Choose ‘OK’ to confirm the setting.

3.6.3 Video Loss

 Please click ( )

LINK>Video Loss and the following screen will appear.

 Select alarm outputs and set up E-

mail addresses for notification

 Link Notification displays E-

mail addresses registered in



Please follow the setup procedures below.

① Click ( )

Video Loss frame and select Video Loss 1.

②

Select cameras for recording when Video Loss 1 is on. Please check

cameras can be set.

③

Select alarm outputs to be worked when Video Loss 1 is on. Please check

More than two alarm outputs can be set.

④ Select E-mail addresses for notifi

cation when Video Loss 1

More than two E-

mail addresses can be set.

⑤

Repeat the above procedure for Video Loss 2~ Video Loss 16.

 Click No Beep 

to deactivate alert sounds from video loss. Apply to

 Choose ‘OK’ to confirm the setting.

960H & SDI DVR



a check box under Link Alarm Out

is on. Please check 

a check box under Link Notification.

RECORD>Settings>Event

when Video Loss occurs.

DEVICES>Network>Notification.



a check box under Link Camera. More than two



a check box under Link Alarm Out

is on. Please check 

a check box under Link Notification.

all channels.

Page

49

or

or R1~2.

Digital Video Recorder for Ness IQ-

Series

3.6.4 Serial In

 Please click ( ) LINK>Serial In

and the following screen will appear.

 Select cameras for recording while the

Serial In

notification.

 Link Notification displays E-

mail addresses registered in DEVICES>Network>Notification.



Please follow the setup procedures below.

① Click ( )

Video Loss frame and select

② Select cameras for recording when

Serial In

cameras can be set.

③

Select alarm outputs to be worked when

More than two alarm outputs can be set.

④ Select E-

mail addresses for notification when

than two E-

mail addresses can be set.

⑤ Repeat the above procedure for

Serial In

 Click No Beep 

to deactivate alert sounds from video loss. Apply to all channels.

 Choose ‘OK’ to confirm the setting.

3.6.5 System Event

 Please click ( )

LINK>System Event and the following screen will appear.



Select recording cameras and alarm outputs while Emergency recording using

for notification.

 Link Notification displays E-

mail addresses registered in DEVICES>Network>Notification.

 Please follow the setup procedures b

elow.

①

System Event frame displays Emergency, which user does not have to change.

②

Select cameras for recording when emergency occurs. Please check

cameras can be set.

③

Select alarm outputs to be worked when emergency occurs. Please check

More than two alarm outputs can be set.

④ Select E-

mail addresses for notification when emergency occurs

More than two E-

mail addresses can be set.

 Choose ‘OK’ to confirm the setting.

960H & SDI DVR

is in operation and alarm outputs and set up E

Serial In 1.

1 is on. Please check 

a check box under Link Camera. More than two

Serial In 1 is on. Please check 

a check box under Link Alarm Out

Serial In1 is on. Please check 

a check box under Link Notification. More

2~ Serial In 16.

EMERGENCY



a check box under Link Camera. More than two



a check box under Link Alarm Out

. Please check 

a check box under Link

Page

50

-mail addresses for

or R1~2.

key and set E-mail addresses

or R1~2.

Notification.

Digital Video Recorder for Ness IQ-

Series

3.6.6 Popup Link

 Please click ( )

LINK>Popup Link and the following screen will appear.

 When Motion or Alarm-

In is detected, user can select a popup or beep sound

interest to pop-up on Spot Screen.



Please follow the setup procedures below.

① Select camera
② Popup: Please Check 

a check box under

③ Beep: Please Check 

a check box under



Click Copy to All Cameras button, then the present channel setup will apply to all other cameras.

 Choose ‘OK’ to confirm the setting.

960H & SDI DVR

for warning, or have a particular channel of

making the popup screen for main monitor.

making beep sound.

Page

51

Digital Video Recorder for Ness IQ-

Series

4.

OPERATION INSTRUCTION

4.1 Viewing

4.1.1 First Image



Power on DVR and the following live video will appear,



The screen will display date/time and icons below.

Icon

Continuous recording mode

Event recor

Event recording mode (Alarm In)

In recording

PTZ registration/PTZ

In Audio recording

16

CMS Access Indication/No. of accesses (up to

In channel sequencing

Setup in HDD Overwrite mode

Setup in HDD None Overwrite mode(recording)

Setup in HDD None Overwrite mode(HDD Full)

 On the right bottom

side of the screen, disk usage will show by %.



On the left top side of each channel screen,



At the normal state, HDD Overwrite mode is on and



When Overwrite mode is off Information>Record>

icon will be changed to .

960H & SDI DVR

while viewing and recording at the same time.

Description

ding mode (Motion)

mode

16)

, , , , ,

icon will show as its operation.

icon shows.

Overwrite Setting),

will show. And when the disk becomes full, the

Page

52

Digital Video Recorder for Ness IQ-

Series

 Click Emergency recording button,

 Click Audio button,

icon will show. And click channel button, then user can change only audio channel.

NOTE

When front key does not work well, please check whether the audio icon

4.1.2 View Format



The available view formats when the Main Monitor is in viewing mode include Full Screen, Split Screen, Channel

Sequencing Screen and PIP screen.

- Full Screen:

Please press camera select key (

NOTE

Using a mouse: Double click to view the corresponding camera image in full view format and click one more time to back to

- Split Screen: Please press

DISPLAY

alternately (i.e., 2x2, 3x3 and 4x4).

- Channel Sequencing: Please press

SEQUENCE

automatic sequence function is not limited to the full screen format, but can be used in any view mode. In 8 channel DVR,

4-

camera sequencing view mode is possible and in 16 channel DVR, 4 or 9

4.1.3 Digital Zoom

 Select a Channel into Full Screen.
 Drag a portion to zoom by mouse.


Double click mouse to exit zoomed screen.

 This

function works only in the full screen.

sequencing or PIP mode.

4.1.4 Freeze Live Image

 Press FREEZE

key while viewing live image to pause the image.



The Freeze function works only in the full screen or split screen formats. Please do not use this function in channel

sequencing mode or in PIP mode.

4.1.5 Pan / Tilt Control

 Press PTZ

key to adjust PTZ cameras connected to DVR. Pan/Tilt mode is available only in the full screen format.

960H & SDI DVR

icon will show.

is activated on the screen.

1~16

) to view the corresponding camera image in full view format.

key and the available split screens (or multi-

window view formats) will display

key to display images in sequencing view form

-

camera sequencing view modes are possibl

Users can

not use the digital zoom function in split screen

Page

53

Split Screen.

at periodically. This

e.

format, channel

Digital Video Recorder for Ness IQ-

Series

 In Pan/Tilt mode, the

icon is displayed on the bottom of the screen.

 Following is the key

usage found in Pan/Tilt mode.



To use a mouse in Pan/Tilt mode, please move the cursor to the lower portion near the center of the screen. To use front

button in Pan/Tilt mode, please push setup button.



To activate PTZ control OSD menu, user must move the cursor to the bottom right portion of the screen.

will show as follows:



To save current camera number, select Preset No and



To move to preset, select preset No and



Available 1 ~ 255 Preset numbers can saved it depends on camera specification.

 As explained earlier in 4.4.2.,

press Menu button to pop

items.

- Since these functions make use of a

memory function of the camera itself, user should set them in Camera OSD.

-

Once user completes the setup, close the Camera OSD menu.

-

User can conveniently use Tour and Pattern functions simply by clicking Tour and Pattern buttons.

- Particulars on how to setu

p each function on OSD Menu are found in the manual of a corresponding camera.

NOTE

Suppose a command for using Tour function is 71 ~ 79 + P

button to benefit the Tour function (70 + 1~9).

960H & SDI DVR

Key Function

Up/Down/Left/Right rotation

Zoom out

Zoom in

Focus near

Focus far
Iris Close

Iris Open

Save Preset

Go to the Preset

Go to OSD main menu

Run Group Tour 1~9

Run Pattern 1~9

button click.

button click.

-

up PTZ camera OSD setup screen and set up Tour and Pattern

reset

and if you had set Tour to 70, use Preset No: 1 ~ 9 + Tour

Page

54

A key pad control

Digital Video Recorder for Ness IQ-

Series

NOTE

It is required to set Menu as Preset number 95 from camera in order to call camera menu display by clicking

using 95+Goto button.

4.1.6 System Log

 Press EVENT

key and the System Log screen will appear.

 Please refer ‘SETUP>SYSTEM>

System Log’ to learn different events listed on the System Log and see how to delete the

System Log.

4.1.7 Key Lock



Press AUDIO>FF>FORWARD keys in sequence to operate the key lock function. This function is indicated by

the lower portion on the right-

hand side of the screen.



Once the Key Lock function is activated, user cannot use any key. If wish to use a key, please enter the correct password to

release the key lock function. If Password is not required, simply press ENTER

4.1.8 Emergency Recording

 When user presses EMERGENCY

key, recording starts right away regardless of preset recording mode.



Emergency recording is not operated while SETUP.



Press Emergency key one more time to stop the emergency recording.

4.2 Search

 This involves searching

recorded video to playback the wanted video of a specific date and time.

 Press SEARCH

key on the viewing screen, or

appear.

960H & SDI DVR





 key.

Click Search menu at “Function Keys”

and the following Search menu will

Page

55

‘menu’ button or

icon in

Digital Video Recorder for Ness IQ-

Series



There are three ways to search video, i.e., by date/time

- Date/Time Search:

search by inputting date/time.

- Calendar Search:

search by using calendar.

- Event Search: search by event.

4.2.1 Date / Time Search

 Please click ( )

Date/Time Search in SEARCH menu and the following input box will appear.



Follow the procedure below to search video by date/time.

① Click (

) the date and/or time whichever user needs to change and block the item. The designated item will be marked in

a square.

② Click ▲, ▼ buttons on the right-

hand side to adjust the values.

 Choo

se ‘Search’ to confirm the setting. Then, the selected video will be played back.



Playback continues from the designated time until the last recording time.

4.2.2 Calendar Search

 Please click (

) Calendar Search in SEARCH menu and the following input box will



Dates and Time with recorded data available will be high



Follow the procedure below to search video by calendar.

①

Select Year and Month by using the arrow buttons in the calendar.

- : search subsequent ‘Year’

- : search previous ‘Year’

- : search subsequent ‘Month’

- : search previous ‘Month’

② Click (

) a date. The date will be displayed in black color.

③ Click (

) the box on the time indication bar to select the search time. The selected time zone will be focused in different

color.

④ Click (

) the selected time box to show pop

960H & SDI DVR

and by calendar.

appear.

-lighted.

-

up window on the screen, If there is a recorded data.

Page

56

Digital Video Recorder for Ness IQ-

Series

⑤

The screen will show selected date/time.

⑥ Click ▲▼

button for selecting cameras.

⑦ Click

then recorded data will be highlighted on the bar.

⑧

Selected camera will show the time bar 0

⑨ Click (

) the box on the time indication bar to select the start time of the video playback

 Click ( ) Search key

to start playing back th



Playback continues from the designated time until the last recording time.

NOTE

Click ( )

search button to show entire channel search based on different time frames

4.2.3 Event Search

 Please click (

) Event Search in SEARCH menu and the



This involves searching recorded video to playback the selected video of a specific date and time.

 Press SEARCH

key on the viewing screen, or use the mouse wheel (central button) and the following Search menu will

appear.

① Designate Event Search start time.
② Designate Event Search end time.
③

Select camera (video) to search data.

④

Check a check box (Motion / Alarm In / Emergency / Serial In) Check box.

⑤

Click on Search Index button to recorded search event data.

960H & SDI DVR

-

60 and It will be marked on 2.5minutes basis during selected time zone.

e selected video.

following input box will appear.

Page

57

Digital Video Recorder for Ness IQ-

Series

4.3 Playback



This involves searching recorded video to playback the wanted video of a specific date and time in search mode.

 Press SETUP

key or please press the mouse right button and click in Playback mode. Then, the following screen will appear.

 There

are three ways to search video, i.e., by date/time and by calendar.

-

Date/Time Search: search by inputting date/time.

-

Calendar Search: search by using calendar.

- Event Search: search by event.



There are three other functions in playback mode;

- Archive: The

Archive function will allow user to copy the recorded video (moving images and still images) from a storage

device (USB memory stick, DVD-

RW).

-

Exit Search: From playback display to live display.

-

Cancel: Hide menu in playback mode.

 Playback mode runs in the

available maximum number of split screen format. To change the viewing mode, please press

DISPLAY key or Camera Select

key (1~16).

NOTE

Using a mouse: Double click to view the full

screen

 Move

the cursor of the mouse and the keypad control will appear at the bottom near the center of the screen.

 Every time user presses the

PLAY/PAUSE

displayed sign on the screen also changes from



Following is the key usage found in playback mode. User may also use the keypad provided on the screen.

Go to Start

• Go to start of recorded data

REW

• Fast reverse playback

(changes to x2, x4,

BACKWARD

• Frame

PLAY

• Playback mode: 1X PLAY

PAUSE

• PAUSE

FORWARD

• Frame

FF

• Fast forward playback

(changes to x2, x4, x8, x16, x32, x64 and Extreme with each press)

Go to End

• Go to end of

 Press SEARCH

key to stop playing back video.

960H & SDI DVR

and double

click one more time to back to Split Screen.

key during playback mode, it is changed to ‘1X PLAY’ and ‘PAUSE’. The

to

x8, x16, x32, x64 and Extreme with each press)

-by-frame reverse still image playback

-by-frame forward still image playback

the recorded data

Page

58

Digital Video Recorder for Ness IQ-

Series

4.4 One-touch Playback

 Press the PLAY/PAUSE

key or double click the mouse wheel (central button) in the viewing mode. Then, user will be able to

view the wanted recorded video right away without going through the search procedure. The video plays back the recorded

video from the last one minute. To

stop playing back the video, please press

4.5

Digital Zoom in Playback

 Users

are able to use Digital Zoon function in full screen playback.



Drag a partition on to the screen, then the partition will enlarge as a full screen.

 Double click the

left button of mouse to exit the zoom

4.6 Archive



The Backup function will allow user to copy the recorded video (moving images and still images) from a storage device (USB

memory stick, DVD-RW).



Please execute Backup Live or playback.

 Follow the backup procedure.

① Press ARCHIVE

key. In case of using a mouse, please press the mouse right button and click in Archive. Then, the

following screen will appear.

② Click ( ) Format frame to select

EXE

images.

③ Click (

) the keyboard display on the right

④ Click (

) the keyboard display on the right

⑤ Click (

) Destination frame to select a storage device out of USB and DVD

⑥ Click (

) the keyboard display on the right

input extension (exe, avi

, jpeg). Please note that the file is

⑦ To set the Password to the file

that users

button and set a password.

⑧ Check 

a check box next to a camera with the video that wa

time.

⑨ Click ( ) the Calculator button

capacity will show only for EXE Archive.

⑩ Click ( ) Start button. Then,

Progress bar will appear and the storage process proceeds. The progress bar does not

show actual progress time. Depending on to the file size, it will appear again even after it shows 100%. It is important not

to detach storage device until DVR displays “A

⑪

If the storage is done properly, Archive Success message will pop up. Please choose ‘OK’ to confirm. If the storage fails,

Archive Fail message will pop up. In this case, user must try again.

960H & SDI DVR

SEARCH key.

-in screen.

, AVI or JPEG. Choose EXE or AVI

for storing moving images; and JPEG for still

-

hand side of FROM frame to set the storage start time.

-

hand side of TO frame to set the storage end time.

-RW.

-

hand side of File Name frame to input a file name. User does not need to

not going to be stored unless user inputs a name.

want to save, mark the check box of “u

se Password”

nt to store. User can archive multi channel at the same

on the rightmost side of Format line to check the data capacity for backup. The

rchive Success” message.

Page

59

. Then, Click the keyboard

Digital Video Recorder for Ness IQ-

Series

NOTE

Please do not use jpeg format while archiving

in live mode.

NOTE

P

lease do not change the settings by DVR or CMS, while back up

NOTE

P

lease enter all the necessary information before Click

NOTE

If the W

hen the targeted file size is over 2GB, press

continue to archive to another file with the extension of

is finished and press “ ” to contin

ue to the rest of progress

CAUTION

PLEASE DO NOT USE THE SPACE WHEN ENTER BACKUP FILE NAME.

CAUTION

WHILE BACKUP PROCEDURE, PLEASE DO NOT DETACH STORAGE DEVICE OR POWER OFF THE DVR. OTHERWISE, IT MAY

CAUSE PERMANENT DAMAGE TO THE DVR OR THE STORAGE DEVICE. IN SUCH CASE, USER MUST REBOOT THE DVR. IF THE

DVR DOES NOT OPERATE PROPERLY, USER MIGHT NEED

CAUTION

WHEN ARCHIVING IN AVI FORMAT, IT ONLY SUPPORTS 1CH AND DOES NOT SUPPORT AUDIO AND PASSWORD FEATURES.

4.7 Menu Bar



Menu bar enables users to control all function as front button on the OSD screen.

 Move the mouse cursor to

bottom around Date and Time indication then Menu bar will show up on the live screen.

 Each icon functions as below;

: Exit the Menu Bar
: Safely turn off the DVR
: Enter Archive mode
: Enter PTZ control mode
: Enter Setup mode

: Turn the display as 1 channel full screen. Additional click on full screen, it will change to next channel in sequence.

: Turn the display as 4 channels split screen

: Turn the dis

play as 8 channels split screen

: Turn the display as 16 channels split screen, There is no changes when additional click on 16 channels split screen.

: Select the multisport split m

ode by clicking MS and 1/4/9/16 buttons.

: Play Instant Playback
: Enter Calendar Search
: Date and Time Search
: Enter Event Search

960H & SDI DVR

.

‘START’.

“ ” button on the right again after the first

“ARCHIVE SUCCESS”.

“-002” Automatically added. I

n case of DVD media, change the media after the first file

.

TO CONTACT SERVICE CENTER.

.

Additional click will change to the next four channels in sequence.

.

Additional click will change to the next eight channels in sequence.

Page

60

And DVR will

Digital Video Recorder for Ness IQ-

Series

: Showing current Date & Time

4.8 Alarm Out Control

 Please click ( ) Color / Alarm

in SEARCH popup menu or in front

NOTE

This function is enabled only when

LIVE MODE

NOTE

4 / 8 Channel has 1 Alarm Relay out,

16 Channel

 Please click ( ) Color / Alarm in

SEARCH popup menu or in front panel and the following input box will appear.

 Choose ‘Close’ to confirm the setting.

CAUTION

ALTHOUGH USERS TURN ITS SYSTEM SETTING TO DEFAULT, THE ANALOG OUTPUT WILL STAY PREVIOUS OUTPUT METHOD

AND NOT EFFECT BY THE DEFAU

LT SETTING.

Phone : [phone] Fax [phone]

960H & SDI DVR

panel and the following input box will appear.

and 4 SPLIT SCREEN MODE or HIGHER.

has 2 Alarm Relay outputs

www.nesscorporation.com

HEAD OFFICE

Ness Corporation Pty Ltd

ABN 28 069 984 372

Sydney

Ph 02 8825 9222 Fax [phone]

[e-mail]

Melbourne

Ph 03 9874 6400 Fax [phone]

[e-mail]

Brisbane

Ph 07 3399 4910 Fax [phone]

[e-mail]

PERTH

Ph 08 9328 2511 Fax [phone]

[e-mail]

Adelaide

Ph 08 8152 0000 Fax [phone]

[e-mail]

Page

61