Ness 104-424 Nano, 104-420 Nano Setup Manual

Page 1
104-424 / 104-420 Nano 4ch / 8ch DVR
FIRMWARE UPDATE PROCEDURE
Page 2
Innovative Electronic Solutions
www.ness.com.au
Page 3
1
We use EH1116H-4 series DVR as an example in following sections.
Please make sure your DVR model before download DVR firmware. Wrong DVR models firmware may cause the DVR system break down.
I. USB Recovery
Save the firmware on USB pen drive and through the USB port on DVR unit to upgrade the firmware of DVR system.
Also, user can create a folder named Update and save the export configuration file and IP cam patch file to import the configuration and update IP camera patch when upgrading firmware. This is a save time and flexible way for user to choose the firmware and IP camera patch version that user wants to use.
1. Download the firmware from website http://surveillance.aver.com/ >>
Support
>>
download Center
>>
Embedded hybrid DVR
>>
EH1116H-4 Nano/EH1116H-4+
or
EH6108H+/EH6216H
+
>>
firmware
. Then,
click
Search
button to search firmware. After firmware has found, select the file named
EH1116H-4
Series_Firmware_USB_*
or
EH6108H+/EH6216H _Firmware_USB_*
to download it.
[Note]
EH1116-4 series firmware version is
05b
, EH6000H series firmware version is
05c
, and
above
has
supported firmware upgrading, import configuration file, and IP camera patch upgrading at the same time.
Page 4
2
2. After download the firmware file, un-zip the file and save on USB pen drive. [Note] Copy the entire firmware file folder into USB pen drive.
3. Then, create a folder named
Update
and copy the IP camera patch file that user can download from web site
http://surveillance.aver.com/ same as downloading the firmware file and import configuration file that user
has export from DVR system. The name of import file must to be
import.cfg
”.
[Note]
a. The update folder is saved in the same directory as firmware file folder. b. If user dont need to import configuration file or upgrade IP camera patch in different version, the
update folder is not necessary to create at this point.
4. Un-pug the USB mouse from DVR unit.
5. Next, plug the USB pen drive to
left side
of USB port on DVR unit. Then, power on DVR unit. While the DVR
is reading file, the screen is black. Please wait for a System Recovery Procedure window to show up.
6. When System Recovery Procedure window show up, click
Yes
to continue it. If user wants to cancel the
firmware upgrade procedure, click No.
The firmwares version is going to update.
The folder contains the firmware.
The folder contains the IP cam patch and import configuration file.
Page 5
3
7. After firmware upgrade is completed, the DVR system will check the files of Update folder and if configuration file and IP camera patch file has found, then, the import and upgrade procedure will be processed.
8. After all procedures have completed, the Reboot window is show up. Click
Reboot
button and remove the
USB pen drive from DVR unit to restart DVR system.
i
-
The DVR system will reboot automatically if Reboot button hasn’t been click for a period time.
-
Remember to remove USB pen drive after click reboot button; otherwise, the DVR system will start upgrade process again.
9. After reboot, user can go to
Setup
>>
System
to check the version of firmware and make sure the upgrade
process is successful.
If file is not found, the message is displayed it.
The message displayed the IP camera path or import configuration file that contains in Update folder has been upgraded or imported.
Page 6
4
II. Local UI Upgrading
Upgrade the DVR system firmware through Update button in System Setting window.
i
- When upgrading DVR firmware, the IP camera patch file is upgrading at the same time.
- When upgrading IP camera patch file, only IP camera patch file is upgraded.
1. Download the firmware from website http://surveillance.aver.com/ >>
Support
>>
download Center
>>
Embedded hybrid DVR
>>
EH1116H-4 Nano/EH1116H-4+
or
EH6108H+/EH6216H+
>>
firmware
. Then,
click
Search
button to search firmware. Select the file named
EH1116H-4 Series_Firmware_Button_*
or
EH6108H+/EH6216H _Firmware_Local_*
to download it. After download the firmware file, unzip it and
save the firmware file on USB pen drive.
[Note]
Firmware file is
*.bin
file type.
Page 7
5
2. Plug the USB pen drive to USB port on DVR unit. Then, click
Setup
>>
System
and click Update button.
3. After click update button, Firmware Update dialog is shown up and DVR system has detected the firmware file on USB pen drive and ready for upgrading procedure. User can check the firmware version to make sure the firmware is newer than current version. Click OK to start upgrading procedure.
4. Wait for a while, DVR system is starting to upgrade firmware.
Current DVR System firmware version
Click it to start firmware upgrade
Page 8
6
5. After upgrade is completed, click OK and DVR system will reboot automatically.
Page 9
7
III. Remote ISP Upgrading
User can upgrade the DVR firmware from remote PC.
i
- The PC that uses to upgrade DVR firmware must can connect to DVR system through LAN or WAN network.
- The DVR hard disk needs to have 250MB free spec.
- When upgrading DVR firmware, the IP camera patch file is upgrading at the same time.
1. Download the firmware from website http://surveillance.aver.com/ >> Support >> download Center >> Embedded hybrid DVR >> EH11116H-4 Nano/EH1116H-4+ or EH6108H+/EH6216H+ >> firmware. Then, click Search button to search firmware. Select the file named EH1116H-4 Series_Firmware_Remote_*” or EH6018H+/EH6216H_Firmware_Remote_* to download it. After download the firmware file, unzip it and save the firmware file on PC. The firmware file contents one ISP application and DVR firmware file.
Page 10
8
2. Run the ISP application on PC and enter the DVRs IP address, Port (Remote Update Configuration port in Network setting), and Password (admin password). Then, Click Read File button and locate where firmware file is.
3. Click Connect button to connect with DVR system.
4. After connected with DVR system, click Upload button to upload the firmware to DVR system.
Page 11
9
5. Then, click Confirm button to start upgrading procedure. If user wants to discontinue the upgrade procedure, click Stop button instead Confirm button.
6. After confirm the upgrade procedure, the upgrading window is displayed on screen at DVR system site.
7. Wait until the upgrade complete message is displayed on ISP application, the upgrade procedure is completed. The DVR system will reboot automatically.
Page 12
© 2012 AVer Information Inc. All Rights Reserved.
Loading...