Ness 104-261 Instruction Manual

INSTRUCTION MANUAL

104-261 series

Infrared Illuminator Housing and

Infrared Day & Night True Color Camera

www.ness.com.au

IP66 RoHS

SAFETY WARNING / IR Illuminator Housing SPECIFICATIONS

CAUTION:

TO REDUCE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT REMOVE COVER.
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

UNPACKING:

Unpack carefully. Electronic components can be damaged if improperly handled or
dropped. If an item appears having been damaged in shipment, place it properly in
its carton and notify the shipper.

IMPORTANT NOTE:

1.Read and follow Instructions: All operating and user instructions should be read and

followed before the unit is to be operated.

2.Electrical Connections: Only a qualified electrician allow to make electrical connections.

Model Number: 104-261
Power Input AC24V(+/-10%)
Power Consumption 16 Watts(11IR)

IR Light Distance
LED Quantity 11 High Power Units

Infrared Beam Angle 25
IR Light on / off Auto Light Sensor Control
Heater Control 18℃(on) / 28℃(off)
Blower Control 35℃(on) / 25℃(off)
Environmental Operating Temp. -20℃~ +45
Protection Level IP66
Temper Glass Thickness 4mm
Mounting Bracket Fully-cable Management
Construction Die-Cast Al uminum Alloy
Coating Ivory Powder Stove

approx’ 120M

ﾟ

＊

℃

Dimension 425(L) x 160(W) x 165(H) mm
Camera Space 200(L) x 110(W) x 115(H) mm
Weight 3500gm

＊IR Light Distances are entirely dependant upon environmental site conditions and

the location at which the unit is situated. The type of camera being used is also
very important.

2

CAMERA SPECIFICATIONS

Image device SONY 1/3" interline transfer Super HAD CCD
Signal system PAL
Picture Elements 752(H) x 582(V)
Scanning system 625 lines. 2:1 interlace
Lens 7.5 ~ 50mm Vari-focal ED-IR Lens
Horizontal resolution 540 TV lines

0.1 lux at F1.2(30 IRE,AGC on)

Minimum Illumination

Infrared wavelength from 780 to 1100nm
AGC Auto Gain 36dB
S/N ratio Better than 50dB
Electronic shutter control 1/50 - 1/100,000 sec.
White balance control ATW(2500ﾟK-9000ﾟK) / AWB
Digital Noise Reduction Automatic
D/N OLPF switch delay time 5 ~ 8 sec
Color/Mono switching chain reaction with D/N filter
Frame integration 4 x factory default
Gamma 0.45
AE/ALC AE/ALC(1/50)
AE/ALC(FL) AE/FL(1/100)

0.001lux at F1.2(B/W mode, AGC on, sense up on)
0 lux under infrared illumination

AGC ON (36dB) / OFF
IR accuracy No focus shift in the night time
BLC ON /OFF
Day/Night Control ON /OFF
Sense up ON (4X) /OFF
Video output signal composite: 1.0 V p-p at 75ohm load
Auto iris lens type Accepts DC servo iris lens
Operating temperature -10ﾟC to 50ﾟC
Power source AC24V/DC12V (Non-polarity)

Power consumption

Dimension (W x H x D) 57 x 53 x 105mm

90mA (AE mode)

110mA (Auto Iris mode)

3

S

CAMERA FUNCTIONS

DIGITAL NOISE REDUCTION COLOR VIDEO CAMERA

The digital noise reduction technology is built into the camera to eliminate any noise associated

with low night environment. Ghost and blooming effects are reduced dramatically, leaving the

Image clean and vivid.

DAY AND NIGHT MECHANICAL FILTER REMOVABLE

The smart day and night mechanical filter removable allows changing between color monochrome
Mode, and user could define the filter to work correctly during day time and night time (invisible

light). And the infrared light sensing responses wavelength of invisible light from 700 to 1100nm.

Auto Iris , AES and Flicferless Function Adj usting

A.I AES

A.I AES

FLOFF

Super AGC and Normal AGC Adjusting

SAGC NAGC If you install the camera at low lux environment, please switch to SAGC

OFF BLC The combination of two types Backlight makes it easier to arrange Backlight

If you are using fixed or manual iris lens, set AES mode to control Exposure

with the electronic shutter.

If you are using an auto iris lens, set A.I mode, the shutter speed is fixed to
1/50 second.

If camera is installed into different frequency, the flickerless function will
reduce the flicker of video. The shutter is 1/120.

, it will increase the camera sensitivity.
The factory default setting is SAGC.

combination to match the imaging conditions and installation location.

Day and Night Adjusting

DN ON

Sense UP Adjusting

ENS-UP

OFF The smart day and night mechanical filter removable allows changing between

color and monochrome mode, and user could define the filter to work correctly
during day time (visible light) and night time (invisible light).

Note: The D/N should be at “ON” position and make sure the AGC at SAGC position

. If the switch is at NAGC, the filter will be stayed at day time position.

OFF

Sense up stand for frame integration that is useful for the low iux environment
, the default sense up rate is 4x similar 1/15 sec.

4

250V / 3.15A P2TPTR0001 TRANSPAC

L E N L E N

L E N

OUTPUT_1 OUTPUT_2

AC IN

13 14 15 16

12

MAX

MIN

Part Description

1817

19

1 2 3 4 5 6 7

8

8

Monitor

11
10

9

1

Lens Cap with Heater

2

Temper Glass

Camera

3

IR LED : 11pcs super high power IR LED with refractor .

4

IR Board and IR Board Bracket

5

Universal IR Control Circuit Board : When the IR light turn on, automatically

adjusts any type of color camera from color to monochrome through the universal
IR control circuit.

5

Part Description / Power Connection

6

Camera Bracket

7

Power Supply Unit : AC24V power input , DC12V output.

8

Blower and Blower Bracket

9

Thermostat Switch : Turn on at 18ﾟC and turn off at 28ﾟC for Heater .

10

Video Input BNC Male Connector: Connect to camera.

11

Video Out BNC Female Connector: Connect to monitor.

12

Terminal Board

13

Fuse Holder : With 250V/3.15A fuse .

14

AC IN Terminal block : AC 24V external power input .

15

OUTPUT_1 Terminal block : Plug and fix the power cable of camera .

16

OUTPUT_2 Terminal block : To power supply unit .

17

VR : Adjust VR to set Infrared LED activation level .

18

Thermostat Switch : Turn on at 35ﾟC and turn off at 25ﾟC for Blower.

19

Ground wire: To top cover.

External Power Input Connection：

AC IN

L E N

AC 24V Adapter

IMPORTANT INSTALLATION NOTICE:

TROPICAL, COASTAL SALTWATER ENVIRONMENTS.

If you plan to install this camera into a TROPICAL, SEA, COASTAL SALTWATER or
CORRISIVE INDUSTRIAL water / mist environment, please seal each Stainless Screw and
Fittings with a SILICON GREASE C OMPOUND.
This will help prevent ELECTROLISIS CORROSION occurring and extend the Lifespan of
the Camera and Housing.
and Pre-Mature Deteriation occurring.

6

INSTALLATION

2

3

1

Loosen two screws on both sides of the camera bracket first.
Use provided screw to fix the camera on the camera bracket.

2

3

Adjust zoom, focus and iris of the lens on the camera.

1

Adjust the direction of the camera for proper position, after finished tighten all screws.

How to install Cables through the Mounting Bracket

7

INSTALLATION

Video Out BNC
Female Connector:

Connect to monitor.

To external power source

*Ness Security Product Branches:

[e-mail]

www.ness.com.au

Sydney (Head Office)

Ness Security Products Pty Ltd

ABN 28 069 984 372

4/167 Prospect Highway

Seven Hills NSW Australia 2147

Phone: [phone]

Fax (Sales): 02 9674 2520

Fax (Admin.): 02 9838 8508

Fax (Purchasing): 02 9674 8064

[e-mail]

Melbourne

24 Terracotta Drive

Blackburn VIC 3130

Phone: [phone]

Fax: [phone]

Adjust the direction of the IR
Illuminator Housing for proper
position, after

finished tighten two screws.

[e-mail]

Brisbane

Unit 3A / 471 Lytton Road

Morningside QLD 4170

Phone: [phone]

Fax: [phone]

[e-mail]

Perth

Unit 1, 567 Newcastle Street

Perth WA 6000

Phone: [phone]

Fax: [phone]

[e-mail]

Adelaide

Unit 1 / 22 Ware Street

Thebarton, SA 5031
Phone: [phone]

Fax: [phone]

8