Page 1
GEC-48CHP-R / GEC-416CHP-R
Receiver of 8/16-port Ethernet Extender over Coax with PoC + 4-port 10/100/1000TX Ethernet Switch
This quick start guide describes how to install and use the receiver of 8/16-port Ethernet Extender over Coax with Power over Coax (PoC) +
4-port 10/100/1000Base-T Ethernet switch.
Overview
The GEC-48CHP-R/GEC-416CHP-R receiver works with the transmitter of 1 port Ethernet Extender over
Coax with PoC (FEC-1 1CHP) to provide Ethernet Extension of 8/16 channel 10/100Base-TX over Coaxial
cable to 4-port 10/100/1000Mbps Ethernet. The maximum transmission distance is 800m. The product
support PoC, hence, no power point is required at the camera side for the transmitter (FEC-11CHP) and
its connected IP camera if the camera obtain power from the transmitter via Power over Ethernet (PoE).
The Ethernet data received by anyone of the coax data port (1-8/16) at the receiver is transferred to all
four Ethernet ports (P1-P4). The product is good for retrofit of analogue system by using the existing
coaxial cable infrastructure.
General
To ensure trouble free transportation and storage, all Neotech products must be thoroughly inspected,
tested and properly packed before delivery. Check the product upon receipt for any visible damage which
may have been caused during shipment.
Package Content
Receiver of 8-port Ethernet Extender over Coax with PoC + 4-port 10/100/1000Base-T Ethernet
Switch x 1(GEC-48CHP-R) or,
Receiver of 16-port Ethernet Extender over Coax with PoC + 4-port 10/100/1000Base-T Ethernet
Switch x 1(GEC-416CHP-R)
AC Power Cord x 1
Quick Start Guide x 1
Physical Description
Front Panel
GEC-48CHP-R
GEC-416CHP-R
1 V1.0
Page 2
GEC-48CHP-R / GEC-416CHP-R
Receiver of 8/16-port Ethernet Extender over Coax with PoC + 4-port 10/100/1000TX Ethernet Switch
Rear Panel
GEC-48CHP-R
GEC-416CHP-R
2 V1.0
Page 3
GEC-48CHP-R / GEC-416CHP-R
Receiver of 8/16-port Ethernet Extender over Coax with PoC + 4-port 10/100/1000TX Ethernet Switch
Installation
GEC-48CHP-R/GEC-416CHP-R can be installed on a 19” rack cabinet. The product has 4 mounting holes. Use 4
rack mount screws to securely install the product in the rack cabinet.
Mounting
Holes
Setup
1. The GEC-48CHP-R/GEC-416CHP-R is a plug-and-pl ay device. Connect the socket of AC power cord to the AC
inlet of the receiver and plug the other end into a standard AC outtlet. Turn on the switch, the PWR LED will
then be lit.
2. The READY LED will be lit (ON) when the receiver is ready for data transfer.
3. Connect one end of the coaxial cable to the female BNC connector (COAX DATA) of
GEC-48CHP-R/GEC-416CHP-R and the other end to the transmitter (FEC-11CHP). If the transmitter and
receiver are properly connected and communicated with each other, the ACT will be lit (ON). The PoC LED will
be lit too when the PoC is in use.
4. Connect the Ethernet cable from the NVR or PC or similar equipment to the Ethernet port (10/100/1000M). If
the cable is properly connected, the corresponding LED (100M or 1000M depend on the Ethernet connection)
at the RJ45 port with be lit. If there is data being transferred, the LED will be blinking.
Interface
Pin
RJ-45 Pin Assignment
1
2
3
4
5
6
7
8
Signal Name
TP0+
TP0TP1+
TP2+
TP2TP1TP3+
TP3-
Power Connection
The power interface of GEC-48CHP-R/GEC-416CHP-R complies with the IEC60320-C14 standard and the AC
power socket complies with the IEC60320-C13 standard
3 V1.0
Page 4
GEC-48CHP-R / GEC-416CHP-R
Receiver of 8/16-port Ethernet Extender over Coax with PoC + 4-port 10/100/1000TX Ethernet Switch
IEC60320-C14 AC Power Socket
Cable Connection
Interface Type Support Description Cable Type
10Base-TX
RJ45
100Base-TX
1000Base-T
BNC (Female)
Ethernet over Coax Data RG-59/U or similar
AC power interface with 100~240 V AC
Power
input
LED Status
Label Colour State Indication
PWR Green
ACT Green
READY Green
PoC 1-8
(ET4200CPp-RS
8) PoC 1-16
(ET4200CPp-RS
16)
Green
Steady Power on
Off Power off
Flashing Data transfer within the coaxial cable
Off No data transfer within the coaxial cable
Steady The converter is ready for data transfer
Off The converter is not ready
Flashing Detection stage
ON: 1 sec,
OFF: 5 sec
(Repeat)
ON: 2 sec
OFF: 4 sec
(Repeat)
ON: 3 sec
OFF: 3 sec
(Repeat)
Un-connected or broken coaxial cable
TX is connected with power adaptor (PoC not required)
Overload
Category 3 or above cable
Category 5 or above cable
Category 5 or above cable
AC Power Socket
ON Power over Coax in use
Steady Ethernet connection of 10/100Base-TX is established
100M Green
Ethernet
1000M Yellow
Flashing Transmitting or receiving Ethernet data
Off
Steady Ethernet connection of 10/100/1000Base-T is established
Flashing Transmitting or receiving Ethernet data
Off
Neither valid Ethernet connection established nor transmitting or
receiving Ethernet data
Neither valid Ethernet connection established nor transmitting or
receiving Ethernet data
4 V1.0
Page 5
GEC-48CHP-R / GEC-416CHP-R
Receiver of 8/16-port Ethernet Extender over Coax with PoC + 4-port 10/100/1000TX Ethernet Switch
Dimensions (Unit: mm)
Functional Descriptions
1U 19”Rack-mount.
Compatible with 1 port EoC Transmitter with PoC/PoE (FEC-11CHP)
Support 16 coaxial cable connections, BNC connectors at rear panels
Support 4 10/100/1000Base-T Ethernet port, 2 ports in front panel and 2 ports in rear panel.
Fully compliant to IEEE 802.3 IEEE 802.3u, 802.3ab standard.
Support auto MDI/MDI-X
Support Power over Coax
Maximum transmission distance 800m
Support multicast
100VAC~240VAC, 50/60HZ power input
Plug and play installation, no PC required
Built in Surge protection
Operating temperature range 0℃ to +50℃
Manual Earth Green manual is available in our website. www.neotechcomm.com.tw
5 V1.0
Loading...