Neotech Communications FMC-11F User Manual

FMC-11F Series Installation & Operation Manual

Inst allation and Operation Manual

FMC-11F Series

Media Converter Series

Industrial 10/100BASE-TX to 100BASE-FX Ethernet Media
Converter

Neotech Communications Corp. Ltd., 2014

www.neotechcomm.com.tw

1

Rev 1.0

Models covered in this manual

Micro Type Wall-Mount

FMC-11F Series Installation & Operation Manual

Fiber connector in SC

Multi-Mode (2-Fiber)

FMC-11F-A

Single-Mode (2-Fiber)

FMC-11F-B

Multi-Mode (1-Fiber)

FMC-11F-C

FMC-11F-D

Single-Mode (1-Fiber)

FMC-11F-E

FMC-11F-F

Fiber connector in ST

Multi-Mode (2-Fiber)

FMC-11F-G

Single-Mode (2-Fiber)

FMC-11F-H

Multi-Mode (1-Fiber)

FMC-11F-I

FMC-11F-J

Single-Mode (1-Fiber)

FMC-11F-K

FMC-11F-L

www.neotechcomm.com.tw

2

FMC-11F Series Installation & Operation Manual

Table of Contents

TABLE OF CONTENTS ................................................................................................................................ 3

(1) SAFETY INSTRUCTIONS .................................................................................................................... 4

(2) PRODUCT OVERVIEW ........................................................................................................................ 5

2.1 INTRODUCTION ................................................................................................................................... 5

2.2 PRODUCTS HIGHLIGHTS ...................................................................................................................... 5

2.3 MODELS SELECTION TABLE .................................................................................................................. 6

(3) INST ALLATION .................................................................................................................. .................. 7

3.1 GENERAL ........................................................................................................................................... 7

3.2 PACKAGE CONTENTS .......................................................................................................................... 7

3.3 SELECTING A SITE FOR THE MEDIA CONVERTER .................................................................................... 8

3.4 INSTALLATION ..................................................................................................................................... 8

3.5 INSTALLATION- WALL MOUNT ............................................................................................................... 9

3.6 CONNECTING TO POWER ..................................................................................................................... 9

DC Terminal Block Power Input ............................................................................................................ 9

(4) CABLE CONNECTIONS & SETUP PROCEDURES ......................................................................... 10

4.1 SYSTEM CABLE CONNECTIONS ........................................................................................................... 10

4.2 CONNECTING TO YOUR NETWORK ...................................................................................................... 11

4.2.3 The 10/100Base-TX Connector/Cabling ................................................................................. 11

4.2.4 The 100Base-FX Connectors ................................................................................................ 12

(5) OPERA TIONAL GUIDES ................................................................................................................... 13

5.1 LEDS STATU S ................................................................................................................................... 13

5.2 SIGNAL AND POWER PORTS ............................................................................................................... 13

(6) SPECIFICATIONS .............................................................................................................................. 14

(7) DRAWINGS ........................................................................................................................................ 16

(8) WARRANTY INFORMATION ............................................................................................................. 16

(9) CONTACT INFORMA TION ........................................................................................................... ..... 17

APPENDIX A ................................................................................................................................................. Q

1. CONNECTOR PINOUTS ...................................................................................................................... B

www.neotechcomm.com.tw

3

FMC-11F Series Installation & Operation Manual

(1) Safety Instructions

Please be familiar with all information in this manual prior to installation and
operation.

Note 1: The products described contain a Class 1 laser or LED fiber optic emitter. The following

safety precautions apply.

Warning: Do not disconnect the fiber optic connector while the unit is powered up.

Exposure to Class I invisible optical radiation is possible when the internal fiber optic

connector is disconnected while the unit is powered up.

Caution: Any access to the controls, adjustments, or performing operations, which are

other than those specified, may result in hazardous radiation exposure. Permanent eye

damage or other bodily injuries may be resulted from such exposure even for only

seconds.

Note 2: This assembly contains parts sensitive to damage by electrostatic discharge (ESD). ESD

precautionary procedures should be applied in the course of touching, removing or inserting parts

or assemblies.

www.neotechcomm.com.tw

4

FMC-11F Series Installation & Operation Manual

(2) Product Overview

2.1 Introduction

Neotech’ FMC-11F media converter offers an easy and affordable solution for network managers

to connect 10/100 Fast Ethernet from UTP to fiber optic cabling. The media converter series uses

a high performance auto-sensing exchange chip for full functionality of transfer and exchange,

guaranteeing the safety and stability of data transfer. The media converter is available in both

single-mode and multi-mode fiber.

This Sleek Microtype design media converter occupies limited space and it's ideal solution for

easy installation within most camera housings.

2.2 Products Highlights
Basic Features

 Microtype design - fits within most camera housings

 Converts 10/100Base-TX to 100Base-FX

 Full/Half duplex, Auto-Negotiation

 Singlemode or Multimode fiber operation

 Single or Dual-core fiber with SC or ST connectors

 Store and forward switching mechanism

 MDI/MDI-X Auto-Crossover supported

 Plug-and-Play

 12VDC or 24VAC Terminal Block Power inputs

 -10 °C to 60 °C (14 °F to 140 °F) operating temperature

 Supports Wall Mounting installation.

www.neotechcomm.com.tw

5

2.3 Models selection table

FMC-11F Series Installation & Operation Manual

Descriptions

Models

Fiber Options Wavelengths

FMC-11F-A Multimode/2-fiber/SC 1310nm 14dB 2Km

FMC-11F-B Singlemode/2-fiber/SC 1310nm 21dB 20Km

FMC-11F-C Multimode/WDM 1-fiber/SC TX:1310nm/RX1550nm 21dB 2Km

FMC-11F-D Multimode/WDM 1-fiber/SC TX:1550nm/RX1310nm 21dB 2Km

FMC-11F-E Singlemode/WDM 1-fiber/SC TX:1310nm/RX1550nm 19dB 20Km

FMC-11F-F Singlemode/WDM 1-fiber/SC TX:1550nm/RX1310nm 19dB 20Km

FMC-11F-G Multimode/2-fiber/ST 1310nm 14dB 2Km

FMC-11F-H Singlemode/2-fiber/ST 1310nm 21dB 20Km

FMC-11F-I Multimode/WDM 1-fiber/ST TX:1310nm/RX1550nm 21dB 2Km

FMC-11F-J Multimode/WDM 1-fiber/ST TX:1550nm/RX1310nm 21dB 2Km

FMC-11F-K Singlemode/WDM 1-fiber/ST TX:1310nm/RX1550nm 19dB 20Km

Links

Budget

Max.

Distance

Mounting

Micro Type

Wall-mount

FMC-11F-L Singlemode/WDM 1-fiber/ST TX:1550nm/RX1310nm 19dB 20Km

www.neotechcomm.com.tw

6

FMC-11F Series Installation & Operation Manual

(3) Installation

3.1 General

All Neotech products are thoroughly inspected, tested and securely packaged before

delivery to ensure a stable, intact and trouble-free service. Please check the equipment upon

receipt for any visible damage which may have been caused during shipping.

3.2 Package Contents

When you unpack the product package, you shall find the items listed below. Please inspect

the contents, and report any apparent damage or missing items immediately to your authorized

reseller.

 Media Converter
 Quick Installation Guide
 External 12VDC power adapter & Power Cord

The FMC-11F Series (Fig. 3.1) can be either horizontally or vertically wall-mounted, or fits

within the most camera housings, etc. It works with an external 12VDC or 24VAC power supply.

Fig. 3.1 FMC-11F

www.neotechcomm.com.tw

7

FMC-11F Series Installation & Operation Manual

3.3 Selecting a site for the Media Converter

As with any electric device, you should place the Media Converter where it will not be
subjected to extreme temperatures, humidity, or electromagnetic interference. Specifically,
the site you select should meet the following requirements:

- The ambient temperature should be between -10 to +60 degrees Celsius.

- The relative humidity should be less than 95 percent, non-condensing.

- Surrounding electrical devices should not exceed the electromagnetic field (RFC)
standards.

- Make sure that the Media Converter receives adequate ventilation.

- The power outlet should be within 1.8 meters of the Media Converter.

3.4 Installation

This chapter gives step-by-step instructions about how to install the Media Converter:

a) Mount the FMC-11F onto a fixture or camera housings, e.g. a plank, (either on

the wall or on a flat surface) with two screws through the holes on the mounting

frame to secure it in position.

b) The power supply should also be mounted on the same fixture or in the proximity

for connection of the supply cables to the unit, provided that an AC power supply

socket is nearby for powering the adaptor.

c) Connect all the signal inputs and outputs at the unit with appropriate cables: fiber

optic cable for optical link and UTP/STP Cat 5 cable for Ethernet. Please refer to

Section 4.1 for the details.

d) Once the unit is powered up, check that the POWER LED on the unit is lit. If not,

check the power supply cable connections between the unit and the power

supply socket.

e) With all the signals available at the physical ports, check the status of LEDs

located on the unit. With correct status of each LED, installation is now completed

[for LEDs status, see Operational Guides on this manual’s Section (5)].

www.neotechcomm.com.tw

8

FMC-11F Series Installation & Operation Manual

3.5 Installation- Wall Mount

(a) Top view (b) Side view

Fig. 3.2 Dimension of Micro type units

 Installation: Mount the Micro type unit onto a fixture, or camera housings, e.g. a

plank, (either on the wall or on a flat surface) with at least 2 screws piercing through
the holes on the mounting frame to secure it in position.

 Startup: Connect the supply voltage to start up the Media Converter via the terminal

block.

 Removal: Locate and remove the securing screws. Usually, but not limited to, at

least 2 screws.

3.6 Connecting to Power

Bottom panel – Ethernet Port and Power Input

Ethernet Port

NETWORK -

RJ45
connector

Power Input Assignment

Top Panel Bottom Panel

12VDC

1GND
2 12V

Terminal
Block

DC Terminal Block Power Input

Step 1: Connect the DC power cord to the pluggable terminal block on the bottom of

Media Converter and then plug it into a standard DC outlet.

Step 2: Disconnect the power cord if you want to shut down the Media Converter.

www.neotechcomm.com.tw

9

FMC-11F Series Installation & Operation Manual

(4) Cable Connections & Setup Procedures

4.1 System cable connections

Signal

Type

Optical Single-mode or Multi-mode fiber SC or ST Connector Section 4.2.2

Ethernet Twisted-pair Cable

10BASE-T: UTP/STP Cat3, 4, 5

100BASE-TX: UTP/STP Cat 5

12VDC

Or

24VAC

Power cord

Cable Type Connector For details,

please refer to

RJ45 Connector Section 4.2.1

Terminal Block

Section 3.6

Wiring Diagram

www.neotechcomm.com.tw

Fig 4.1 Media converter connection diagram

10

FMC-11F Series Installation & Operation Manual

4.2 Connecting to Your Network

4.2.1 Cable Type & Length

It is necessary to follow the cable specifications below when connecting the Media
Converter to your network. Use appropriate cables that meet your speed and cabling
requirements.

Cable Specifications
Speed Connector Port Speed

Half/Full Duplex

10Base-T RJ-45 10/20 Mbps 2-pair UTP/STP Cat. 3, 4, 5 100 m

100Base-TX RJ-45 100/200 Mbps 2-pair UTP/STP Cat. 5 100 m

100Base-FX SC, ST 100/200 Mbps MMF (62.5μm) 2 km

100Base-FX SC, ST 100/200 Mbps SMF (9 or 10μm) 20km

Cable

Max.
Distance

4.2.2 Cabling

Step 1: First, ensure the power of the Media Converter and end devices are turned off.

<Note> Always ensure that the power is off before any installation.

Step 2: Prepare cable with corresponding connectors for each type of port in use.

Step 3: Consult the cabling requirements based on connectors and speed.

Step 4: Connect one end of the cable to the Media Converter and the other end to a desired device.

Step 5: Once the connections between two end devices are made successfully, turn on the power and the

Media Converter is operational.

4.2.3 The 10/100Base-TX Connector/Cabling

A standard straight through cable is used for the connection between the Ethernet switch and

device. The products feature an auto-MDIX capability. For the details, Please see Appendix A for

your reference.

www.neotechcomm.com.tw

11

FMC-11F Series Installation & Operation Manual

X

)

X

(

X

X

4.2.4 The 100Base-FX Connectors

The 100Base-FX Connections

The fiber port pinouts

The TX (transmit) port of device I is connected to the RX (receive) port of device II, and
the R

(receive

port of device I to the T

transmit) port of device II.

X value:

A for Multimode fiber
B for Singlemode fiber

FIBER Connector
TX

SC Optical Connector

RX

SC Optical Connector

X value:

G for Multimode fiber
H for Singlemode fiber

FIBER Connector
TX
RX

ST Optical Connector

ST Optical Connector

The WDM 100Base-FX Connections

The fiber port pinouts

Only ONE optical fiber core is required to transmit and receive data.

* Special note for choosing WDM products:

Pair of products should be used for the optical transmission by different wavelengths (1310nm, 1550nm).

i.e. FMC-11F-C-MT should be match with FMC-11F-D-MT;
FMC-11F-E-MT should be match with FMC-11F-F-MT;
FMC-11F-I-MT should be match with FMC-11F-J-MT;
FMC-11F-K-MT should be match with FMC-11F-L-MT.

www.neotechcomm.com.tw

value:

C and D for Multimode fiber
H and F for Singlemode fiber

FIBER

Connector

SC Optical Connector

value:

I and J for Multimode fiber
K and L for Singlemode fiber

FIBER

12

Connector

ST Optical Connector

(5) Operational Guides

5.1 LEDs Status

LED State Indication

FMC-11F Series Installation & Operation Manual

PWR

FX LINK
SPD

LINK/
ACT

Green Power on.

Off Power off.

Green 100Base-FX

Green 100Base-TX

Off 10Base-TX

Steady A valid network connection established

Flashing Transmitting or receiving data.

ACT Stands for Activity.

5.2 Signal and Power Ports

FIBER - SC or ST Optical Connector(s) for 100BASE-FX fiber cable connection.

NETWORK - RJ45 with Cat. 5 for 10/100BASE-TX Ethernet connection.

DC12V-

AC24V -

2-pin Screw Terminal Block for 12VDC or 24VAC power connection.

www.neotechcomm.com.tw

13

(6) Specifications

Ethernet

FMC-11F Series Installation & Operation Manual

Standards

Address table size
Processing Type

Forward and Filter Rate

10Base-T

100Base-TX/FX

Cabling

10BASE-T

100BASE-TX

Maximum Distance

Cat5 UTP

Connector

10/100BASE-TX

IEEE 802.3 10BASE-T

IEEE 802.3u 100BASE-TX/FX

IEEE 802.3x

2048MAC addresses

Store-and-Forward

Half-duplex and IEEE802.3x Full-duplex flow control

10 / 20Mbps half / full-duplex

100 / 200Mbps half / full-duplex

UTP/STP Cat. 3, 4, 5 or above

UTP/STP Cat. 5 or above

Up to 100m

1X RJ45

Optical

Cabling

Maximum Distance

62.5/125μm (Multi-mode)

9/125μm (Single-mode)

Multi-mode fiber 2Km

Single-mode fiber 20Km

Wavelength(s)

1310nm

1310/1550nm

Connector

SC or ST

Electrical and Mechanical

Input Power

12VDC or 24VAC (Terminal Block)

Power Consumption
Operating Voltage & Max.

2.4W Max.

0.2A @ 12VDC

Current Consumption

www.neotechcomm.com.tw

14

LED Indicators

FMC-11F Series Installation & Operation Manual

Power

10/100 TX (Per Port)

100FX (Per Port)

Dimensions
Net Weight
Casing

Mounting Options

Environmental

Operating Temperature
Storage Temperature
Humidity

Regulatory Approvals

ISO9001

Power Status

Link/Activity, Speed

Link/Activity

36.2mm (W) × 117mm (D) × 24.5mm (H)

0.12Kg (0.22kg including PA)

Aluminum case

Wall-Mount

-10°C to 60°C (14°F to 140°F)

-24°C to 85°C (-13°F to 185°F)

0% - 95% non-condensing

FCC Part 15, Class A

EN61000-3-2: 2006

EN61000-3-3: 2008

EN55024: 1998 +A1:2001+A2:2003

www.neotechcomm.com.tw

15

(7) Drawings

FMC-11F Series Installation & Operation Manual

Fig. 7.1 Dimensional drawings of FMC-11F (mm)

(8) Warranty Information

All Neotech FMC-11F Series products are subject to a three-year limited warranty offered by

the company in normal circumstances. Please refer to the Neotech Products Warranty Statement

for details. Access to the statement is available in our company website at

www.neotechcomm.com.tw.

www.neotechcomm.com.tw

16

FMC-11F Series Installation & Operation Manual

(9) Contact Information

Taipei Operation

Address:

5F., No.46, Sec. 2, Minquan E. Rd., Zhongshan Dist., Taipei City 104, Taiwan (R.O.C.)

Tel: [phone]

Fax: [phone]

Sales Inquiries

[e-mail]

Technical Support

[e-mail]

www.neotechcomm.com.tw

17

Appendix A

1. Connector Pinouts

RJ45 Connector (Male) RJ45 Connector (Female)

FMC-11F Series Installation & Operation Manual

2. TIA/EIA-568 Cabling

RJ45
Pin #

Wire Diagram Wire Color

1 White/Green Transmit+ White/Orange Transmit+

2 Green Transmit- Orange Transmit-

3 White/Orange Receive+ White/Green Receive+

4 Blue Unused Blue Unused

5 White/Blue Unused White/Blue Unused

6 Orange Receive- Green Receive-

7 White/Brown Unused White/Brown Unused

8 Brown Unused Brown Unused

T568A T568B

10Base-T Signal

100Base-TX Signal

Wire Diagram Wire Color

10Base-T Signal

100Base-TX Signal

3. Standard, Straight-Through Wiring Diagram(both ends are the same):

The Straight-Through wiring (or called “regular” Ethernet cable), both ends should be use

the same pin out on of RJ45 port.

www.neotechcomm.com.tw

B