Page 1
FEC-11CV Series
Industrial 10/100Base-TX Ethernet plus CVBS Over Coaxial Converter
This quick start guide describes how to in stall and u se the Industrial Coaxial Converte r . This is the Coaxial Converte r
of choice for harsh environments constrained by space.
Overview
FEC-1 1CV is a p air of 10/100Base-TX Ethernet plus CVBS (composite video baseband signal) over coax converters.
It completely complies with the international standards such as IEEE 802.3 10Base-T, IEEE802.3u 100Base-TX,
and IEEE 802.3X.
The product series consists of a transmitter (FEC-11CV-T) and receiver (FEC-11CV-R). The maximum transmission
distance of a coaxial cable is 300m. The FEC-11CV series products can transmit not only the existing CVBS over
the coaxial cable, but also the IP signals of network products (e.g. IP cameras) at the same time. With FEC-11CV
series products, it is a cost effective way to upgrade the analogue video surveillance system to workable with the IP
cameras to the video surveillance system without laying the cable again.
General
To ensure trouble free transpor tation and storage, all Neotech prod ucts must be thoroughly inspected , tested and
properly packed before delivery. Check the product upon receipt for any visible damage which may have been
caused during shipment.
Package Content
Transmitter (FEC-11CV - T) or Receiver (FEC-11CV-R) of Ethernet Extender over Coaxial Converter x1
Power Adapt er x 1
Quick Start Guide x 1
Physical Description
Front/Rear Panel
Power Input
SPD PWR
Link/ACT ACT
CVBS
Input / Output
CVBS
In/Out
LINK
Coax Data
1 V1.0
Page 2
FEC-11CV Series
Industrial 10/100Base-TX Ethernet plus CVBS Over Coaxial Converter
Installation
a) The product has two mounting holes. See Figure 1 for its structure. Mount the product on wall or a flat surface.
Mounting holes
Figure 1. Case dimensions
b) Typical cable connection diagram:
Installation Steps
a) Connect the COAX DATA connector of the transmitter (TX) and receiver (RX) with coaxial cable.
b) At TX side, connect the analogue camera video signal to the CVBS INPUT connector with coaxial cable, the IP
camera signal to the Ethernet port (10/100) with network cable.
c) At RX side, connect the monitor to the CVBS OUTPUT with the coaxial cable, the NVR/switch to the Ethernet
port (10/100) with network cables to the switch or PC.
d) The PWR light is on when the product is powered on. Check if the power cable is working properly.
e) After all cables are correctly connected, the indicators will be lit as per port status LEDs (page 3).
2 V1.0
Page 3
FEC-11CV Series
Industrial 10/100Base-TX Ethernet plus CVBS Over Coaxial Converter
Interface
Ethernet Port:
a) Ethernet port RJ45:
10/100M Ethernet port pin sequence diagram:
Power Connection
GND
12VDC
-
12V
+
- +
Pin MDI Signal Definition
1
TD+ RD +
2
TD- RD-
3
RD + TD+
4 NC
5 NC NC
6
RD- TD-
7 NC
8 NC NC
Terminal Block
MDIX Signal
Definition
NC
NC
3 V1.0
Page 4
FEC-11CV Series
Industrial 10/100Base-TX Ethernet plus CVBS Over Coaxial Converter
The Port Status LEDs, dimension drawing of the Micro unit
Indicator Color Description
PWR
LINK
COAX
DATA
ACT
CVBS IN (TX only)
CVBS OUT (RX only)
SPD
10/100
(Ethernet)
LINK/ACT
Green Power on.
Off Power off.
Green The COAX DATA link
(between TX & RX) is
established.
Flashing Data is being
transmitted or received.
ACT Stands for Activity.
Green Video input
Green Video output
Orange 100Base-TX
Off 10Base-TX
Steady A valid network
connection is
established
Flashing Data is being
transmitted or received.
ACT Stands for Activity.
Functional Description
Ethernet Extension : Security Link over Coax
Simultaneous transmission of IP and CVBS over single coaxial cable
Constant Data Rate : 36Mbps(Downlink)/11Mbps(Uplink)
Maximum distance : 300m over Coax(RG-59/U)
Support Auto MDI/MDI-X
-10Ԩ to 60Ԩ operating temperature.
Assembly, Startup, and Dismantling
Installation
Installation: Mount the Micro type unit onto a fixture, or camera housings, e.g. a plank, (either on the wall or on
a flat surface) with at least 2 screws piercing through the holes on the mounting frame to secure it in position.
Startup: Connect the supply voltage to start up the Media Converter via the terminal block.
Dismantling: Locate and remove the securing screws. Usually, but not limited to, at least 2 screws.
Manual Earth Green manual is available on our website www.neotechcomm.com.tw
4 V1.0
Loading...