TB400
User Manual
Version 6.10.0.07
Yeastar Technology Co., Ltd
NeoGate TB400 User Manual
www.yeastar.com 2
Table of Conte nts
1. INTRODUCTION ....................................................................................................................... 3
1.1 Hardwar e Specification ................................................................................................... 3
1.1.1 Exterior Appearance ................................................................................................. 3
2. SYSTEM SET UP ....................................................................................................................... 5
2.1 Installation of BRI Module. ............................................................................................ 5
2.2 Ethernet Line Connection ............................................................................................... 5
2.3 Power Supply Connection ............................................................................................... 5
3. NEOGATE C ONFIGURATION ................................................................................................. 6
3.1 Manager Login ................................................................................................................... 6
3.2 BRI Sett i ngs ....................................................................................................................... 6
3.2.1 Modu le List .................................................................................................................. 6
3.2.2 BRI Settings ............................................................................................................... 7
3.2.2.1 Basic Setti ngs.................................................................................................................... 7
3.2.2.2 CallerID Prefix Settings .................................................................................................. 8
3.2.2.3 Advance d Settings ........................................................................................................... 8
3.3 VOIP Se t ti ngs ................................................................................................................... 10
3.3.1 SIP Se ttings .............................................................................................................. 10
3.3.1.1 SIP Account ..................................................................................................................... 10
3.3.1.2 R egister to SIP ................................................................................................................ 11
3.3.1.3 Service Provider ............................................................................................................. 12
3.3.1.4 Advance d Setting ........................................................................................................... 12
3.3.2 Advanced Settings .................................................................................................. 13
3.4 Route List .......................................................................................................................... 17
3.4.1 Manage Calling Routes .......................................................................................... 17
3.4.2 DOD List .................................................................................................................... 19
3.4.3 Blacklist...................................................................................................................... 20
3.5 Syste m Se t ti ngs .............................................................................................................. 20
3.5.1 Options ....................................................................................................................... 20
3.5.2 Network Setting ...................................................................................................... 21
3.5.3 Passw o rd Settings .................................................................................................. 23
3.5.4 Date and Time ......................................................................................................... 23
3.5.5 Backup and Restore ............................................................................................... 24
3.5.6 Reset and Reboot .................................................................................................... 24
3.5.7 Firmware Update ..................................................................................................... 25
3.6 Reports .............................................................................................................................. 26
3.6.1 Call L og s .................................................................................................................... 26
3.6.2 Syst e m In fo .............................................................................................................. 26
4. APPLICATION .......................................................................................................................... 28
NeoGate TB400 User Manual
www.yeastar.com 3
1. Introduction
NeoGate Gateway for Maximum Efficiency & Cost Savings
NeoGate TB400 is a d evice for connecting BRI Network to VoIP Network directly,
which can support two-way com muni ca t i on: BRI to VoIP or VoIP to BRI.
It is the best solution ever to connect IP-based telep hone systems, soft switches,
and IP-PBXs to BRI network.
1.1 Hardware Specification
1.1.1 Exterior Appearance
1) Front Side
Figure 1-1 NeoGate TB400 Front Panel Picture
No. Identifying
①Power Green shining: Connected, correct function.
②RUN
Green Light：Indicates the server system is in working order
③Ready
Green Light：Indicates the system is ready.
④BRI 1
Orange Shining: BRI 1 connected
①② ③④④ ⑤⑥ ⑦
NeoGate TB400 User Manual
www.yeastar.com 4
⑤BRI 2
Orange Shining: BRI 2 connected
⑥BRI 3
Orange Shining: BRI 3 connected
⑦BRI 4
Orange Shining: BRI 4 connected
2) Back Side
Figure 1-2 NeoGate TB400 Back Side
NeoGate TB400 User Manual
www.yeastar.com 5
2. System set up
2.1 Installation of BRI Module.
Open the case of NeoGate, adjust the pins to the slots and insert then insert
the spins into the slots.
Note1: Please turn off the device when installing the modules.
2.2 Ethernet Line Connection
NeoGate provides two 10/100M Ethernet p o rt s wi th RJ4 5 i n te rfac e an d LED
indicator. Plug Ethernet line into NeoGate’s Ethernet port, and then
connect the other end of the Ethernet line wit h a hub, switch, router, LAN or
WAN. Once connected, check the status of the LED indicator. The green LED
indicates the port is properly connected.
2.3 Power Supply Connection
NeoGate utilizes the high-performance switch power, which supply the
enough voltage and electrical energy that required by NeoGate system.
AC Input: 100~240V
DC Output: 12V,1A
Please follow the steps below to connect the NeoGate unit to a power outlet:
1. Connect the small end of the powe r c abl e to the power input port on the
NeoGate back p anel, and plug the other end of the cable into a 100VAC
power outlet.
2. Check the Power LED on the front panel. A solid green LED indicates that
power is being supplied correctly.
NeoGate TB400 User Manual
www.yeastar.com 6
3. NeoGate Configuration
3.1 Manager Login
From your web browser, input the IP address of the NeoGate server.
If this is the first time you are configuring NeoGate, pleas e us e th e default
settings below:
IP Address: http://192.168.5.150
Username: admin
Password: password
Figure 3-1
3.2 BRI Settings
3.2.1 Module List
You can check the information of the status of BRI modules and trunks. Click
edit to configure the trunk.
NeoGate TB400 User Manual
www.yeastar.com 7
Figure 3-2
NeoGate Status Description:
Status
OK: The port is idle.
Disconnected: No line connects to this port.
3.2.2 BRI Settings
3.2.2.1 Basic Settings
Figure 3-3
Trunk Name: A name of this Trunk. Ex: 'BRI1' etc.
Signaling: You can choose the signaling of BRI. It supports BIR-NET,
BRI-NET-PTMP, BRI CPE, BRI-CPE-PTMP.
Default DOD: You ca n se t t he default DOD here.
Max. Call Duration (min)/Per Month: Defines the maximum call duration
within a month through this SIM ca rd . (0 it means unlimited)
Clear Stat: Set the day in a month on which the stati st i cs d ata on Max. Call
NeoGate TB400 User Manual
www.yeastar.com 8
Duration are deleted. This parameter is ignored if set to 0.
3.2.2.2 CallerID Prefix Settings
You can add prefix to the incoming call here.
Figure 3-4
3.2.2.3 Advanced Settings
Figure 3-5
·Switch Type:
National: National ISDN type2 (common in US)
ni1: National ISDN type1
dms100: Nortel DMS100
4ess: AT&T 4ESS
5ess: Lucent 53SS
NeoGate TB400 User Manual
www.yeastar.com 9
Euroisdn: Euro I S DN
Qsig: Minimalistic protocol to build a ‘network’ with t wo or more pbx of dif ferent
vendors.
·PRI Dialplan
Sets an option required for some (rare) switches that require a dialplan
parameter to be passed. This option is ignored by most PRI switches. I t may be
necessary on a few pieces of hardware. This option can almost always be left
unchanged f rom th e default.
·Reset Interval
Set the time in seconds between resta rt of unuse d cha nne l s. S ome PBXs don't
like channel restarts. so set the interval to a very long interval e.g. 100000000
or 'never' to disable *entirely*. If you are in Israel, the following is important:
As Bezeq in Israel doesn't like the B-Channel resets happe ning on the lines, it is
best to set t he reset i nt e rva l t o 'ne ve r' whe n i nstalling a b ox in Isra e l. Our past
experience also shows that this parameter may also cause issues on local
switches in the U K and China.
PRI Local Dialplan
Sets an option required for some (rare) switches that require a dialplan
parameter to be passed. This option is ignored by most PRI switches. It may be
necessary on a few pieces of hardware. This option can almost always be left
unchanged f rom th e default.
·Overlap Dial
Whether MyPBX can dial this switch using overlap digits. If you need Dir ect
Dial-in (DDI; in German \"Durchwahl\") you should change this to yes, then
MyPBX will wait after the last digit it receives.
·PRI Indication
Tells how MyPBX should indicate Busy() and Congestion() to the switch/user.
Accepted values are:
inband: MyPBX plays indication tones without answering; not available on all
PRI/BRI subscription lines
outofband: MyPBX disconnects with busy/congestion information code so the
switch will play the indication to nes to the cal ler. Busy() will n ow do same as
setting PRI_CAUSE=17 and Hangup().
·Enable Facility
To enable transmission of facility-based ISDN suppleme ntary servi ces (such a s
caller name f rom CP E ov e r f acility), enab le t his option.
NeoGate TB400 User Manual
www.yeastar.com 10
Nsf
Used with AT&T PR Is.If outbou nd calls are be ing r ejected due to \"Mandatory
information element missing\" and the missing IE is 0x20, then you need this
setting.
Echo Cancellation
Disable or enable echo cancellation.
Hide CallerID
Whether to Hide Caller ID.
3.3 VOIP Settings
3.3.1 SIP Settings
Figure 3-6
3.3.1.1 SIP Account
It is an SIP Account that allows an IP Phone, IP Soft- Phone client, IPPBX a n d
soft switch to register on NeoGate.
·Extension
The numbered extension, i.e. 20001, that will be associated with this particular
User / Phone.
·Password
The password for this extension, e.g.: ‘pincode20001’.
NeoGate TB400 User Manual
www.yeastar.com 11
Figure 3-7
3.3.1.2 Register to SIP
‘Register to SIP’, It use to register to SIP Server or SIP Proxy.
·Hostname/IP
Service provider’s hostname o r IP address.5060 i s the standard port number
used by SIP protocol. Don’t change this part if it is not required.
.Domain
Put the VoIP provider’s server domain n a me here.
·Username
Put the username of SIP account. U sed for SIP trunk registration.
.Authorization name
Used for SIP authentication. Lea v e this blank if not required.
·Password
Put the password of SIP account.
.From User
All outgoing calls from this SIP Trunk will use the From User (In this case the
account name for SIP Registra tion) in From Header of the SIP Invite.
.Online number
Define the online number that expected by ‘Skype Connect’ and some other SIP
service providers. Leave this field blank if it's no required.
·Outbound Proxy Server
A proxy that receives requests from a client, e ven though which may not be the
server resolved by the Request-URI.
NeoGate TB400 User Manual
www.yeastar.com 12
Figure 3-8
3.3.1.3 Service Provider
·Hostname/IP
Service provider’s hostname or IP address.
Note: 5060 is the standard port number used by SIP p rotocol. Don’t change this
part if it is not required.
Figure 3-9
3.3.1.4 Advanced Setting
·Max. Call Duration (min)
Set the maximum call duration here. 0 means no limit.
NeoGate TB400 User Manual
www.yeastar.com 13
Clear Stat
The date of each month the system will clear the call history.
DTMF Mode
You can set the DTMF mode here (rfc2833,info,inband,auto, def ault is rfc2833).
Max. Channels
Set the ma xi mum channels here. 0 means no limit.
Allowed Codecs
Choose the codes allowed here. (Default u-law, a-law, GSM)
Figure 3-10
3.3.2 Advanced Settings
NeoGate TB400 User Manual
www.yeastar.com 14
Figure 3-11
1) General
·UDP Port
Port use for sip registrations, Default is 5060.
·RTP Port Start
Beginning of RTP port range
·RTP Port End
End of RTP port range
·Max Registration/Subscription Time
Put down the maximum duration (in seconds) of a SIP registration. Default is
3600 seconds.
·Min Registration/Subscription Time
Put down the minimum duration (in seconds) of a SIP registration. Default is 60
seconds.
·Default Incoming/Outgoing Registratio n Time
Default I ncomi ng /Out g oing Registra t i on Ti me: Default is 30 seconds.
·Register Attempts
The number of SIP REGISTER messages to send to a SIP Registrar before giving
up. Default is 4 (no limit).
·Register Timeout
Put down the number of seconds to wait for a response from a SIP Registrar
NeoGate TB400 User Manual
www.yeastar.com 15
before timed out. Default is 20 seconds.
2) NAT
Note: Configuration of this section is only required when using remote
extensions.
·Enable STUN
STUN (Simple Traversal of UDP through NA Ts) is a p rotocol for assisting d evices
behind a NAT firewall or router with their packet routing.
·STUN Address
The STUN server allows clients to find out their public address, the type of NAT
they are behind and the internet side port associated by the NAT with a
particular local port. This information is used to set up UDP communication
between the client and the VOIP provider and so establish a call.
·External IP Address
Put down the IP address that will be associat ed with outbound SIP messa ges if
the system is in a NAT environment.
·External Host
Alternatively you can specify an external host, and the system will perform DNS
queries periodically.
This setting is only required when your public IP address is not static. It is
recommended that a static public IP address be used with this system. Please
contact y our ISP for more i nformati on.
·External Refresh Interval
If an external host has be en supplied, you may spe cify how often the syst em will
perform a DNS query on this host. This value is specif i ed i n second s.
·Local Network Identification
It’s used to identify the local ne twork using a network number/ subnet mask pai r
when the system is behind a NAT or firewall.
Some examples of this are as follows:
'192.168.0.0/255.255.0.0' : All RFC 1918 addresses are local networks;
'10.0.0.0/255.0.0.0' : Also RFC1918;
'172.16.0.0/12':Another RFC1918 with CIDR notation;
'169.254.0.0/255.255.0.0' : Zero c onf local n e t w ork .
Please refe r t o RF C19 18 f or more informa tion.
·NAT Mode
Global NAT configuration for the system. The options for this setting are as
follows:
NeoGate TB400 User Manual
www.yeastar.com 16
Yes = Use NAT. Ignore address information in the SIP/SDP headers and reply to
the sender's IP address/port.
No = Use NAT mode only accord ing t o RFC35 81 .
Never = Never attempt NAT mode or RFC3581 support.
Route = Use NAT but do not include report in headers.
·Allow RTP Reinvite
By default, the system will route media steams from SIP endpoints through
itself. Enabling this option causes the system to attempt to negotiate the
endpoints to route packets to each other directly, bypassing the system. It is not
always possible for the system to negotiate endpoint-to-endpoint media
routing.
3）QOS
QOS (Quality of Service) is a major issue in VOIP implementations. The issue
is how to gu arantee t hat packet traffic for a voice or other m edia conn ection
will not be dela yed or dropped due int erference from o ther lower priority
traffic.
When the network capacity is insufficient, QoS could provide priority to
users by setting the value.
4）Codecs
·G.729 License Key
Note: If you would like to use G.729, please enter your license.
Figure 3-12
NeoGate TB400 User Manual
www.yeastar.com 17
3.4 Route List
3.4.1 Manage Calling Routes
Calling routing mai nly works for guides out going/incoming ca ll s t o g o t hroug h
trunks.
Click ‘New Calling Route’ and fill in the corresponding in f ormation in the p op up
window.
Figure 3-13
1）General
·Route Name
Put the name of this Calling Route. ex: 'Local' or 'Long Distance' etc.
·Pattern
Outbound calls t ha t match this di a l p a tte rn wi ll use t his outbound route. T here
are a number of dial pattern characters that have special meanings:
X : Any Digit from 0-9
Z : Any Digit from 1-9
N : Any Digit from 2-9
[12345-9] : Any digit in the brackets (in this example, 1,2,3,4,5,6,7,8,9)
The ‘.’ Character will match any remaining digits. E.g.” 9011.” will match any
phone number that st a rts wit h 9011, e xclud ing 9011 it se lf .
The ‘!’ will match any remaining digits, and causes the matching process to
complete as soon as it can be determined that no other matches are possible.
Example 1: NXXXXXX will match any 7 digits phone number.
NeoGate TB400 User Manual
www.yeastar.com 18
Example 2: 1NXXNXXXXX will match a phone number starting with a 1,
followed by a 3-digit area code, and then 6 digit number.
·Strip digits fro m fron t
Allows th e user to specify the n umber o f digi ts that wi ll be stripped from th e
front of the phone number before the call is placed. For example, if users must
press 0 befor e di alin g a pho ne n umbe r, one digit shoul d be s tripped fro m the
dial string before the call is placed.
·Prepend these digits before dialing
These digits will be prepended t o the phone number before the call is placed. For
example, if a trunk requires 10 digit dialing, but users are more comfortable
with 7 digit dialing, this field could be used to prepend a 3 digit area code to all
7 digit ph one numbers bef ore call s are p lace d. When usi ng a nalog trunks, a 'w'
character may also be prepended to provide a slight delay before dialing.
·Direct Number
All the outgoing calls through this route will call to this phone number
directly.
·Strategy
Define the strategy to select trunk．
Default: Select the trunk from the first.
Sequence: Select the trunk next the last used.
Balance: Select the trunk last recent ly use d .
·Time
The scope of time which is allowed to make calls via t his route.
·Days of week
The days in a week when is allowed to make calls via this route.
·Inbound Caller Pattern
Inbound calls that match this dial pattern will use this route. The rule is the
same as Dial Pattern.
·Inbound Trunk
Choose the inbound trunks.
·Outbound Trunk
Choose the outb ound t runks.
NeoGate TB400 User Manual
www.yeastar.com 19
Figure 3-14
3.4.2 DOD List
DOD(Direct Outwa rd Dia li ng ). Set the Call er nu mb e r t o the out b ound trunk.
NeoGate TB400 User Manual
www.yeastar.com 20
Figure 3-15
3.4.3 Blacklist
Number Blacklist is used to block an incoming call you do not want to answer
and block outgoing call.
If the incoming call or outgoing call number is registered in the number blacklist,
the caller will hear the following: “The number you have dialed is not in service.
Please check the number and try again”. The system will then disconnect the
call.
Figure 3-16
3.5 System Settings
3.5.1 Options
1) General
·Ring Timeout
Number of seconds to ring a device before answering. Default value is 30s.
.MAX Call Duration
NeoGate TB400 User Manual
www.yeastar.com 21
The absolute maximum amount of time permitted for a call. A setting of 0
disables the timeout. Default value is 6000s.
·HTTP Bind Port/Web Access Port
Port use for HTTP sessions. Def ault: 80
Figure 3-17
3.5.2 Network Setting
1) LAN
·DHCP
If this option is set, NeoGate will use DHCP to get an available IP addres s
from your local network. Not recommended.
·Enable SSH
This is the advance way to access the devi ce, you can use the putty software
to access the device. In the SSH access, you can do more advance setting
and debug.
·Port: the default is 8022,
·Hostname
Set the host name for NeoGate.
·IP Address
Set the IP Address for NeoGate.
NeoGate TB400 User Manual
www.yeastar.com 22
·Subnet Mask
Set the subnet mask for NeoGate.
·Gateway
Set the gateway for NeoGate.
·Primary DNS
Set the p rimary DNS for NeoGate.
·Secondary DNS
Set the secondary DNS for NeoGate.
2) Advanced Settings
A VLAN is a logical local area network (or LAN) that extends beyond a single
traditional LAN to a group of LAN segments, given specific configurations.
·IP Address2 and Subnet Mask2
.Configure second IP Address and Mask in this text, NeoGate can use this ip
address access to a nothe r net work.
·VLAN Number
.The VLAN Number is a uniq ue value you assig n to each VLAN on a single device.
·VLAN IP Address
Set the IP Address for NeoGate VLAN.
·VLAN Subnet Mask
Set the Subnet Mask for NeoGate VLAN.
·VLAN Gateway
Set the Gateway for NeoGate VLAN.
NeoGate TB400 User Manual
www.yeastar.com 23
Figure 3-18
3.5.3 Password Settings
The default passw ord is ‘password’. T o ch ange the password, enter the new
password and click update. The system will then prompt you re-login using your
new password.
Figure 3-19
3.5.4 Date and Time
Set the date and time for NeoGate.
NeoGate TB400 User Manual
www.yeastar.com 24
Figure 3-20
3.5.5 Backup and Restore
You can backup your configure in this page. After back up, you can see the
back up in the list. You can restore the configure in this page also.
Note: the re store will only work after reboot.
Figure 3-21
3.5.6 Reset and Reboot
·Reboot System
Warning: Rebooting the system will termina t e a ll active calls!
·Reset to Factory Defaults
Warning: A factory reset will erase all configuration data on the system.
Please do not tu rn off t he system u ntil the RUN lig ht begi ns blinking. Any power
interruption du ring this time could cause damag e t o t he syst e m.
NeoGate TB400 User Manual
www.yeastar.com 25
Figure 3-22
3.5.7 Firmware Update
Upgrading of the firmware is possible through the Administrator web interface
using a TFT P Se rv e r or an HTTP URL.
Enter your TFTP Se rver IP a ddress and f irmware file location, then click start to
update t he firmware.
More Information, please see
http://www.yeastar.com/download/NeoGate-TB400/
Note
：
1. If enabled ‘Reset configs’, System will restore to factory default settings.
2. When update the firmware, please don’t turn off the power.
NeoGate TB400 User Manual
www.yeastar.com 26
Figure 3-23
3.6 Reports
3.6.1 Call Logs
The call Log captures all call details, including Source, Destination, Start Time,
End Time, Duration, Billable Duration, Disposition, Communication Type, etc.
Administrator can export CDR data to a CSV file.
Figure 3-24
3.6.2 System Info
General:
Information about hardware v ersion, firmware version and system uptime.
LAN:
Information about hostname, MAC address, IP address, subnet mask,
gateway, Primary D NS and Secondary DNS.
Disk Usage:
Disk usage information.
Memory Usage:
Memory usage information.
NeoGate TB400 User Manual
www.yeastar.com 27
Figure 3-25
NeoGate TB400 User Manual
www.yeastar.com 28
4. Application
Application 1
Figure 4-1
Application 2
Figure 4-2
<Finish>
Loading...