Contents of the box:
PX-3004
Quad Docking Station
Quick Start Guide
November 14, 2008
PN: 8000177.A
The Quad Docking Station
IS
O
9
0
Q
u
a
l
i
t
y
0
1
C
e
r
t
i
f
i
e
d
M
a
n
a
g
e
m
e
n
t
S
y
s
t
e
m
This Guide
Features: Front, Back, And Ports
Charging compartment (quantity 4)
AC/DC adaptor
Power cord
(dependent on country
and order)
Mounting The Quad Docking Station
The Quad Docking Station can be fi xed to the optional
Wall Mount Bracket (model PX3014), or to another surface,
by two broad-headed screws.
Mounting holes (quantity 2)
Drain holes (quantity 4)
Rubber feet (quantity 4)
Mounting screws (quantity 2)
Note: The position of
the mounting holes is
indicated by markings on
the front and sides of the
Quad Docking Station.
Getting Started
Mount the Quad Docking Station.
1
Connect the Docking Station to external power.
2
Note: The power indicator glows green
when the Docking Station is connected
to external power.
Power indicator
DC input connector
Note: Use only the universal AC power
supply approved by Psion Teklogix for
use with the Quad Docking Station.
Connect the Docking Station to an Ethernet network.
3
AC outlet
Power
cord
Power adaptor
The Ethernet connection in the Quad Docking Station
NEO hand-held computers
(up to 4)
USB to Ethernet converter (4)
Quad Docking Station
10 or 100baseT Ethernet
Insert one or more NEO hand-held computers.
4
Ethernet hub
Note: During charge, the LED indicator on
NEO is YELLOW until charging reaches 75%.
Between 75% and 95% the indicator fl ashes
Slide NEO into the Docking
Station until it latches.
GREEN slowly, and, above 95%, the indicator
is GREEN continuously.
Internal Ethernet connection
Ethernet connector
Docking connectors (quantity 4)
Power indicator
DC In connector
Insert the screws into the holes on the base of the unit, then
slide the unit towards the back to secure it.
Ethernet connector
Link LED
Speed LED
10 or 100base-T
Ethernet connector
Allow the NEO computers to charge for three hours
before fi rst use.
Note: Full battery performance is only reached after
0 - 40 °C
32 - 104 °F
the fi rst few charge/discharge cycles.
3 h
Over
Location Guide For Mounting Screws
Dimensions Of Mounting Screws
™
7.50 cm
(2.95 in)
13.3 cm
(5.24 in)
4.75 cm
(1.87 in)
1.90 cm
(0.750 in)
Rubber feet
Front of
Docking
Station
35.8 cm (14.1 in)
23.0 cm (9.10 in)
6.40 cm (2.51 in)
1.90 cm
(0.750 in)
The mounting screws on the shelf are M4 x 6mm panhead screws.
3.50 cm (1.38 in)
Mounting holes
Outline of
Quad Docking Station
28.8 cm (11.3 in)
3.50 cm (1.38 in)
Maximum diameter of screw head:
Maximum height of screw head:
0.45 cm (0.18 in)
Maximum height between screw
head and mounting surface:
0.4 cm (0.16 in)
Maximum diameter of screw shaft:
1.05 cm (0.41 in)
0.65 cm (0.26 in)
Psion Teklogix and NEO are trademarks
of Psion Teklogix Inc. Other product
names mentioned in this document are
trademarks or registered trademarks
of other hardware, software, or service
providers and are used herein for
identifi cation purposes only.
8000177
8000177
Rev. A
PX3004
Quad Docking Station
Quick Start Guide
November 14, 2008 PN: 8000177.A
ISO 9001 Certifi ed
Quality Management System
Loading...