Nemco 6015DP, 6015 User Manual

Lights not On

Check if unit is plugged in and power switch turned to “ON” position

Check power at receptacle

Check if Bulb has blown

Loose Sockets

Turn off power and check if socket is loose or broken. Remove light bulb and tighten
socket screws as necessary.

Loose Hoods

Turn off power and check if hood is loose. Remove light bulb and tighten hood screws
as necessary

Unit Blows Fuse or Circuit Breaker

Check to make sure circuit is not overloaded.

Operating and Maintenance Instructions

Model: 6015-DP Infra-red Bulb Warmer Carving Station 120V

INTRODUCTION

1. Please read instructions before using this appliance.

2. When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electric shock and

injury.

3. Clean machine thoroughly before and after all uses following cleaning instructions below.

ELECTRICAL REQUIREMENTS

1. Plug warmer into a grounded outlet with correct voltage and sufficient power capacity. Refer to the product label (serial plate) on

the warmer for voltage and wattage requirements.

SAFETY INSTRUCTIONS

1. Warning! All power must be disconnected at power source before any service procedure is performed.

2. This appliance is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. Keep combustible materials, such as

drapes and other furnishings, away from appliance.

3. Extreme caution is necessary when any appliance is used by or near children and whenever the appliance is left unattended.

4. Always unplug appliance when not in use and before cleaning, adjusting or maintaining this machine. To disconnect appliance,

turn controls off and remove plug from power source.

5. Do not operate any appliance with a damaged cord or plug, after the appliance malfunctions, has been dropped, or damaged.

Return appliance to an authorized service facility for examination, electrical or mechanical adjustment, or repair.

6. Do not use outdoors. This appliance is not intended for use in wet or moist locations. Never locate appliance where it may fall

into water.

7. Connect to properly grounded outlets only. Avoid the use of extension cords. Do not run cord under carpeting, runners, or the

like. Arrange cord away from traffic area and where it will not be tripped over.

8. This appliance is equipped with a power cord with a three-blade plug. Plug ONLY into a matching three-blade outlet. DO NOT

cut off the third blade or attempt to use with a two-blade extension cord.

9. To prevent a possible fire, it is recommended that the unit is placed on a non-combustible surface.

10. This appliance has electrical parts. Do not use it in areas where gasoline, paint, or flammable liquids are used or stored.

PREPARATION

1. Position carving station at desired location near the power source.

2. Screw bulb into socket and adjust flexible neck.

3. If warmer fails to work properly when first operated call NEMCO customer service at 1-800-782-6761.

OPERATION

1. Plug CORD into a grounded electrical outlet of the correct voltage. Electrical shock can occur if appliance is not grounded.

2. Place food products in a pan located directly under the BULB for best results.

3. Adjust FLEXIBLE STEM ASSEMBLY. Do not aim lamp in any direction other than the surface of the table on which the

appliance is mounted. Maintain a distance of at least 13” between lamp and surface of table. Always maintain a distance of at
least 5” between the hood and any wall.

4. Turn warmer off when not in use.

5. Unplug the warmer before changing BULB. To disconnect warmer, turn switch to off and remove plug from power source.

CLEANING

NOTE: Proper maintenance plays an important part in the life span and functioning of the warmer.

1. Unplug the warmer before cleaning or changing bulbs.

2. This warmer can be cleaned with a damp sponge and mild soap. Do not immerse in water or other liquid.

3. To disassemble cutting board, remove screw on bottom side of board.

TROUBLESHOOTING

1

45884

11-14-12

ITEM
NUMBER

PART NUMBER

DESCRIPTION

QTY
1

66231

HOOD CAP

1 2 66592-1

MOUNTING TUBE

1 3 66232

MINI HOOD

1 4 66007

HOOD

1 5 45372

SOCKET

1 6 45376

BULB

1 7 66214-1-A

TUBE STEM ASSEMBLY

1 8 46368

CORD

1 9 66661

POST WELDRIGHT

1

10

66381-DP

CARVING BOARD BASE

1

11

45955

FOOT

4

NEMCO FOOD EQUIPMENT 301 Meuse Argonne, Hicksville, OH 43526

Phone: [phone] Fax: [phone] Toll free: 1-800-782-6761

www.nemcofoodequip.com

2