Page 1
Installation Manual
L
L
uxon Wireless 245A
L. Hones
11 August 2013
Page 1 of 5
Page 2
can be added to
communication between the
A
the light controller.
Luxon Wireless
HID ballast. It
and the Luxon Light Controller (LLC).
data can be
HID lamps in a building with skylights
1. Brief product description
The Luxon Wireless 245A
wireless
installation the Luxon Wireless 245
wirelessly to and from
Figure 1. Installation example with
a fixture equipped with a Luxon e-
electronic ballast
becomes a RF node in the network, and
facilitates
After
transferred
Page 2 of 5
Page 3
comes mounted into a protective
. This cable is used for both powering the module and the wired
Avoid disconnecting the quite
le female connector with polaris
The module comes with 2
lways disconnect the ballast from mains power prior to connecting the Luxon Wireless 245A
Luxon
Wireless 245A module carry life voltage.
be kept towards other conductors and enclosure parts.
The enclosure is designed to comply with safety standards.
The Luxon Wireless 245A module may only be installed
instructions
The Luxon Wireless 245A module must
best possible unobstructed line of sight to other Luxon Wireless nodes.
best performance let the transceiver have a 360 degree field of sight.
a 23mm diameter
30mm spacing, see also Figure 5
rews
ingress
cable
fragile cable connector from the module.
ation and locking, for use with
a protective sealing, see Fig 3
ballast and powering up, the electronic circuits on the Luxon
ers touching the life parts.
nel
, to let the RF
See also the Figure 4.
, together with two 3mm holes f
nel
2. Product description
Figure 2: LW245A module
The Luxon Wireless 245A
module as shown in Figure 2
communication with the ballast.
The black connector is a 4 po
of Luxon e-HID ballasts.
3. Warnings
A
After making the connection to the
Sufficient creepage distance must
4. Mounting
transceiver have the
For
The module requires
with
The provided two self tapping sc
The sealing can be used if IP65
Figure 3: mounting hardware
plastic enclosure. The
Torx T10 bolts and
It must be made impossible to end us
by qualified and trained person
be mounted to the outside of the luminaire
hole to pop through
. The mounting area shall be flat.
shall be used to secure the module.
protection is required.
is plugged into the
specific series
.
.
.
or the screws
Page 3 of 5
Page 4
The cable is used to make a connection with the ballast. The
Please insert
to remove a small protection cover
to the ballast
See also Figure 7.
connection to ballast (example)
out dimensions
connector has provisions for both
See also Figure 6.
from the ballast that is
cable to minimize
Figure 7: example assembly
Figure 4: Sample application
5. Connecting
polarization and locking.
Note that it might be necessary
connector.
Please note that the cable
electrical interference.
Figure 5: enclosure cut-
black
it carefully into the counterpart on the ballast.
shall be kept away from the lamp output
located over the
Figure 6:
Page 4 of 5
Page 5
CC ID: CGD
This device complies with part 15 of the FCC Rules and to RSS210 of Industry Canada.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, includ
et appareil se conforme aux normes RSS exemptés de
x conditions suivantes
cet appareil ne doit causer aucune interférence, et
(2) cet appareil doit accepter n'importe quelle interférence, y inclus interférence qui peut causer une opération non pas
Changes or modifications not expressly approved
To comply with FCC RF exposure requirements for mobile transmitting devices, this transmitter should only be used or
where there is at least 20cm separation distance between the antenna and all persons.
. Label artwork example for a fixture with LW245A module
Operating temperature
Safety
EMC
/Telecom
-
40 to
EN60950
EN301489
FCC47 part
Dimensions
50 X 36 mm
Input
Supply
3.3 Vdc, +/
Max. 100mA
ing interference that may cause undesired operation.
by the party responsible for compliance could void the user’s
+85°C
15 and IC RSS210
6. Specifications
- 5%
-1, EN300328 V1.7.1
7. FCC and IC Declarations
F
Compliance statement
Déclaration Conformité
C
L'opération est soumis aux deu
(1)
voulu de cet appareil.
Warning
authority to operate the equipment.
RF Exposure
installed at locations
LW245A and IC: 1444A-LW245A
licence du Industry Canada.
8
Page 5 of 5
Loading...