Page 1
Voice/Videophone Calls
■Making calls/videophone calls
Making a Voice/Videophone Call .................................................................................... 2
Switching a Voice/Videophone Call During a Call .......................................................... 5
Making International Calls ......................................................................... 6
Using Handsfree During a Call ........................................................................ 7
Making a Call Using Redial/Dialed Calls/Received Calls
......................................................................................... 8
Using Chaku-moji .......................................................................................... 10
Showing/Hiding Caller ID When Making a Call............................................................... 11
Sending Touch-tone Signals ........................................................................... 12
Using the Prefix Function................................................................................................ 12
Making a Call Specifying a Sub-Address........................................... 13
Setting the Alarm for Reconnection ....................................................... 13
Making the Earpiece Sounds Clear ...................................................... 13
Reducing Surrounding Noise to Make Voice Clear.................................. 14
Talking Handsfree While Driving............................................................ 14
Redial/Dialed calls/Received calls
■Receiving calls/videophone calls
Receiving a Voice/Videophone Call................................................................................ 14
When the Other Party Switches a Voice/Videophone Call ............................................. 16
Pressing a Dial Key to Answer a Call......................................................... 16
Ending/Holding Call by Folding the FOMA Terminal........................... 17
Adjusting Earpiece Volume .................................................................................. 17
Adjusting Ring Volume.................................................................................. 17
■When you can/could not answer a voice/videophone call
Holding Incoming/Current Calls ............................................................... 18
Using Public Mode .......................................................................................................... 18
When You Cannot Answer an Incoming Call .................................................. 20
Recording Voice/Video Messages When You Cannot Answer the Call
................................................................................................................ 21
Recording a Message When You Cannot Answer Incoming Call ............. 22
Playing/Deleting Record Messages/Voice Memos/Moving Picture Memos .................... 22
■Setting the Videophone
Using Chara-den............................................................................................................. 23
Setting Videophone Functions........................................................................................ 23
Using Videophone Call by Interfacing to External Device............................................... 26
WORLD CALL
Handsfree
Chaku-moji
Pause dial
Sub-address setting
Reconnect signal
Hyper Clear Voice
Noise reduction
In-car hands-free
Answer setting
Setting when folded
Vol ume
Ring volume
On hold/Holding
Missed call
Record message
Quick message
1
Page 2
Making a Voice/Videophone Call
Enter the phone number of the
1
other party
Always start with the area
code, even for a call within
Voice/Videophone Calls
the same area.
You can enter up to 80 digits
for the phone number.
However, only the last 26
digits are displayed.
<When you enter a wrong number>
■ To insert a number
Press v to move the cursor to the number to
the left of the position where you want to insert
the number, then enter the number.
■ To delete a number
Press v to move the cursor to the number you
want to delete, then press t.
Hold down t for 1 second or longer to delete
all the numbers to the left of the cursor and the
number in the cursor position.
<Videophone>
■ To make a videophone call with Chara-
den
XUu (FUNC)X“Select image”X“Chara-den”
XSelect Chara-den
Enter phone number
Function menu¨p.4
r (voice call), o (V.phone)
2
<Voice call>
“ ” flashes while dialing
and lights up during the
call.
■ If you hear the busy
tone
The line is busy. Call again
after a while.
■ If you hear a message
that the other party
cannot be reached
The other party’s mobile phone is not turned
on or is out of signal range. Call again after a
while.
■ If you hear a message requesting your
caller ID
Call again with Caller ID Notification enabled.
→p. 11
<Videophone>
“ ” flashes while dialing
a videophone call and
lights up during the call.
■ If a videophone call is
not connected→ p.5
■ To switch between
camera image and
substitute image
XUu (FUNC)X
“Substitute image”⇔“My
side”
■ To send video captured with the rear
camera
XXd (Change)
The front camera and rear camera switch each
time you press Xd (Change).
■ To switch the main screen
XXd (Change) (1 second or longer)
“Change main disp.” → p.4
■ To enlarge a camera image to be sent
XUse Xv to adjust zoom
■ To mute the voice to send
XSa (マナー ) (1 second or longer)
“ ” appears.
To cancel muting, press
second or longer again.
Videophone in-call
Function menu¨p.4
Sa (マナー ) for 1
In-call
2
Page 3
■ To set Hyper Clear Voice →p.13
■ Switching a Voice/Videophone Call During
a Call→ p.5
■ To put the current voice/videophone call
on hold→ p.18
■ When 2in1 is in Dual mode
The Outgoing number selection screen appears.
Select a phone number.
To end the call, press y
3
N
z If no keys are pressed for 15 seconds during a
voice call, the Power saver mode activates.
z If you make an emergency videophone call (110,
119 or 118), the call automatically changes to a
voice call.
z You cannot receive i-mode mail or MessageR/F
during a videophone call (you can receive SMS).
Received mail is stored at the i-mode center and
can be retrieved using “Check new messages”
after the videophone call.
z Digital communications charges apply when the
substitute image is displayed during a videophone
call.
You can use the videophone call function
Videophone
between terminals that support the DOCOMO
videophone system.
z DOCOMO’s Videophone is compliant with the
■Guide to the videophone screen
①Main screen (Camera image of the other party
②Sub-screen (Your own camera image is
③Last call duration
④Settings
*1 : “Send DTMF tone/DTMF tone OFF”→ p.4
*2 : “Using Chara-den” →p. 23
*2
3G-324M
by the 3GPP
international standard established
*1
(the 3rd Generation Partnership
Project that sets standards for 3rd generation
mobile communications systems). Connections
with videophones using different standards
cannot be made.
*1: 3GPP (3rd Generation Partnership Project)
A regional standardization body established to
develop commonly applied technical
specifications for 3rd-generation mobile
communications systems (IMT-2000).
*2: 3G-324M
An international standard for 3rd-generation
mobile videophones.
1
3
4
2
is displayed by default)
displayed by default)
: Hyper Clear Voice (Low/High)
: Voice being transmitted/Transmission
error
: Video being transmitted/Transmission
error
: Camera image/Substitute image/
Chara-den being transmitted
: Handsfree ON/OFF
: Muting
: Visual check in progress
: Photo mode (Portrait/Scenery/Close-up)
: Key operation mode (DTMF
*1
mode
/Whole action mode*2/
Parts action mode
*2
)
Voice/Videophone Calls
3
Page 4
Enter phone number screen
(p.2)
Notify Caller ID→ p.1 1
Prefix numbers→ p.1 2
Chaku-moji→ p.1 0
Int’l call→ p.7
Voice/Videophone Calls
Multi Number
Add to phonebook
Compose message
Select image……Select Me/Chara-den as an image
used during a videophone call. Select “Release
settings” to release the setting.
Videophone in-call screen
(p.2)
Petit message→ p.25
Decoration→ p.2 5
Off decoration……Delete the displayed message or
stamp.
Substitute image⇔My side……Switch between the
camera image and substitute image.
Rear camera⇔Front camera……Switch between
the front and rear cameras.
This setting is only retained during the call.
Change main disp.……Change the main display.
The screen changes in the following order:
“Displaying the image from the other party’s camera
on your main screen”→ “Displaying the image from
your own camera on your main screen”→ “Displaying
only the image from the other party’s camera”→
“Displaying only the image from your own camera”.
Visual check⇔ Visual check off……View yourself
with the front camera during a videophone call.
Otherwise, end checking. “ ” appears and the
substitute image is sent to the other party during
visual check.
V.phone settings……Set the screen for videophone
calls.
Visual prefer.……Select Normal/Prefer img
qual/Prefer motion spd for an image sent to and
received from the other party. This setting is only
retained during the call.
Brightness……Adjust the brightness between
five levels (–2 to 0 to +2).
4
White balance
Color mode set……Select Normal/Sepia/
Monochrome as an image effect. This setting is
only retained during the call.
Photo mode……Select a shooting mode.
Cannot be set for the front camera.
Chara-den set.……Set the following when Chara-
den is used. This setting cannot be set for the camera
images.
Switch Chara-den, Action List, Change
Action
Switch image……Display an image selected in
“Substitute image” (p.24) on the other party’s
display.
Display light……Turn on the light all the time or
follow the “Lighting” settings under “Backlight”.
FrontCamera Rev.……Set whether to display your
camera image as a mirror image (ON) or normal
image (OFF) on your FOMA terminal during a call.
Own number……Display your phone number during
a videophone call.
Send DTMF tone⇔ DTMF tone OFF……Set/
Release push signal transmission mode during
Chara-den. Videophone calls other than Chara-den
are always in push signal transmission mode.
Change to voice→ p.5
Page 5
●
If a videophone call is not connected
When a videophone call is not connected, the cause
of the failure appears.
z The cause may not appear depending on the
situation.
z Depending on the type of the other party’s phone or
network service subscription, the reason may not
accurately reflect the other party’s actual status.
Display Cause
Check number
then redial
Busy The line is busy
Busy with packet
transmission
Out of service
area/power off
Your call is being
forwarded
Redial using voice
call
Please activate
caller ID before
dialing again
This number is not
available
Upper limit has
been exceeded
Connection failed
Connection failed You attempted to connect
Please make your
call from the
i-mode web page
The dialed phone number is
not in use
• This message may also
appear during packet
communication, depending
on the other party’s
terminal.
The other party is using
packet communication
The other party is out of
range or the phone is turned
off
The call is being forwarded (a
videophone call is made
when the forwarding number
is for a 3G-324M-compatible
videophone)
The forwarding phone is not
compatible with videophone
The other party has set the
Caller ID request service
The other party has set the
Nuisance call blocking
service
The upper limit set for a Limit
billing plan (Type Limit or
Family Wide Limit) is
exceeded
without notifying your caller
ID (when dialing into
visualnet, etc.)
• This message may also
appear in other situations.
Set Caller ID Notification to
“ON” and retry.
You attempted to make a
videophone call to watch
V-live without browsing the
i-mode official site
z If the videophone call is not supported, your call is
automatically switched to a voice call when you set
“Auto redial as voice” to “ON”. However, the
videophone may not work properly if you call an
ISDN synchronous 64 KB access point, 3G-324Mincompatible ISDN videophone (as of April, 2009)
or if you dial a wrong number. Call charges may
apply.
Switching a Voice/ Videophone Call during a Call
z You can use this function with terminals compatible
with voice call/videophone call switch.
z You can switch calls only when you are the caller.
z To switch calls, the receiver needs to set “Ntfy
switch-mode” beforehand.→ p.24
<Example: To switch a voice call to a videophone
call>
In-call screen (p.2)Xd (V.phone)
1
X“YES”
During switching, a screen appears indicating
that the calls are being switched, and voice
announcement is played.
Digital communications
charges apply after this
screen appears.
■ To switch a videophone call to a voice call
XVideophone in-call screen (p.2)X
u (FUNC)X“Change to voice”
N
z It takes about 5 seconds to switch the calls. Note
that the signal quality may affect the switching
time.
Voice/Videophone Calls
Continued on next page
5
Page 6
N
z You cannot switch calls in the following cases:
• When the other party is holding the call
• When the other party activates Record
message
z The displayed call duration is reset to 0 second
each time the calls are switched. However, the
total time of the voice and videophone calls is
displayed after the call ends.
Voice/Videophone Calls
z Depending on the other party’s communication
conditions or signal quality, you may not be able to
switch the calls and the call may be disconnected.
z When the call is switched, the first dialed or
received call is stored in the Redial/Dialed calls or
Received calls.
<When switching from voice call to videophone
call>
z If the caller is using i-mode, i-mode is
disconnected and the call is switched to
videophone.
z If the other party is using packet communication
(including i-mode), the message “No Switch”
appears and the calls cannot be switched.
z You cannot switch the calls when “Call Waiting” is
active.
Making International Calls
<WORLD CALL>
WORLD CALL is a service where you can use your
DOCOMO mobile phone to call overseas.
You applied for “WORLD CALL” when you star ted to
use FOMA services. (Except if you did not wish to
apply for it.)
z You can make a call to approximately 240 countries
and regions worldwide.
z “WORLD CALL” charges are billed with your
monthly FOMA call charges.
z In addition to directly dialing a phone number, you
can make an international call by adding “+” or
selecting “Int’l call” or “Prefix numbers” from the
function menu of the enter phone number screen or
Phonebook/Redial/Dialed calls/Received calls
detail screen.
z Services are not available in some billing plans.
For WORLD CALL, call at general inquiries
provided on the back of the manual.
International videophone calls are available with
users of specific roaming operators overseas or
FOMA terminals in Japan.
z See “Mobile Phone User’s Guide [International
Services]” or the DOCOMO International
services website for countries and operators.
z In some types of the other party, international
videophone is not available or the other party’s
picture on FOMA is distorted.
Dialing a phone number to make an
international call
Dial the phone number in the
1
following order: 010 → Country
code→Area code (City code)→
Other party’s phone number
Dial the other party’s phone number excluding “0”
at the beginning of the mobile phone number or
area code (city code). However, to call to some
countries/areas, such as in Italy, “0” is required.
You can also make an international call by
dialing the phone number in the following order:
009130→ 010→Country code→ Area code (City
code)→ Other party’s phone number.
r
2
The international call is made.
Simple procedures for making
international calls
z You can store country codes and international call
access codes in “Int’l dial assistance”.
●
Using “+” to make an international call
“+” changes to “IDD prefix code” set in “Auto int’l call
set.”, and you can make an international call without
dialing the IDD prefix code.
z Since “Auto int’l call set.” under “Int’l dial
assistance” is set to “ON” (automatically added) by
default, the IDD prefix code is automatically dialed.
On the standby screen, dial the
1
following: + (0 (1 second or
longer)) → Country code→Area
code (City code)→Other party’s
phone number
Dial the other party’s phone number excluding
“0” at the beginning of the mobile phone number
or area code (city code). However, to call to
some countries/areas, such as in Italy, “0” is
required.
6
Page 7
rX“Dial”
2
The international call is made.
■ To make a call with the numbers entered
in Step 1
X“Original phone No.”
The international call is made.
■ To cancel calling
X“Cancel”
●
Making an international call from the
function menu
Open the function menu and add the country code
and IDD prefix code to make an international call.
z You can use the international dialing function on
the Enter phone number screen or Phonebook/
Received calls/Dialed calls/Redial detail screen.
<Example: To use the international dial function on
the enter phone number screen>
Enter the phone number of the
1
other party
u (FUNC)X“Int’l call”XSelect a
2
country codeXSelect an IDD
Prefix code
The selected country code and IDD prefix code
are added. “0” at the beginning of the mobile
phone number or area code (city code) is
automatically deleted (except when “Italy” is
selected for the country code).
r
3
The international call is made.
N
z Even if Caller ID Notification is active, the caller ID
may not appear properly depending on the
operator. In this case, calls cannot be made from
the Received calls screen.
Country Code setting……Store up to 22
country names and country codes to use when
making international calls. See “Country codes
of major countries” or the DOCOMO
International services website for country codes.
XHighlight an itemXo (Edit)XEnter a
country nameXEnter a country code
■ To delete a country code
Xu (FUNC)X“Delete”XSelect a deletion
method
IDD Prefix setting……Store the IDD prefix
name and IDD prefix code to use when making
an international call. Up to 3 entries can be
added.
XHighlight an item to store or editX
o (Edit)XEnter an IDD prefix nameXEnter
an IDD prefix code
■ To delete the IDD Prefix
Xu (FUNC)XSelect a deletion method
Using Handsfree During a
Call
The other party’s voice comes from the speaker
during a call.
In-call screen (p.2), Videophone
1
in-call screen (p.2) X
o ()
“ ” appears and the other party’s voice comes
from the speaker during a handsfree call.
While ringing, you can switch to handsfree by
pressing o (/).
<Handsfree>
Voice/Videophone Calls
Setting international calls
Set the auto conversion of “+”, and edit or store
country codes and IDD prefix codes.
iX“Settings/NW Service”X
1
“Dialing”X“Int’l dial assistance”X
<Int’l dial assistance>
Select any item:
Auto int’l call set.……Set the auto conversion
of “+” used when making an international call.
X“ON”XSelect a country codeXSelect an
IDD Prefix code
■ To disable auto conversion
X “OFF”
Voice call Videophone call
■ To release handsfree
XPress o ( ) during a handsfree call
“ ” disappears for voice call.
“ ” changes to “ ” for videophone.
7
Page 8
●
Notes on use
It is recommended that you keep a distance of about
30 cm from the FOMA terminal during a handsfree
call. If it is too close or too far, the other party may find
it difficult to hear you or your voice may sound
differently.
N
z Before switching to a handsfree call, move to an
Voice/Videophone Calls
area where your call will not disturb other people.
z When a call is finished, the handsfree setting is
released.
Making a Call Using Redial/ Dialed Calls/Received Calls
<Redial/Dialed calls/Received calls>
Information on the other party’s phone number and
the date and time is stored in the Redial/Dialed calls/
Received calls. You can make a call to the other party
quickly by using these records.
z When you make calls to the same phone number
repeatedly, the latest entry is saved to Redial and
separate entries are saved to Dialed calls.
z Up to 30 phone numbers for voice calls and
videophone calls can be stored in Redial.
z Up to 30 voice call and videophone call entries and
30 packet communication and 64 KB data
communication entries can be stored in Dialed
calls/Received calls.
z If the maximum number of entries is exceeded,
older entries are overwritten.
<Example: To make a call from the Redial/Received
calls list screen>
On the standby screenX
1
j (Redial) or h (Received calls)
■ To check Dialed calls
XiX“Own data”X“Dialed
calls”
Ex. Redial (list)
Function menu¨p.9
Highlight a Redial/Received calls
2
entry
■ To make a call after
checking the details of
the Redial/Received
calls entry
XSelect a Redial/Received
calls entry
Ex. Redial (detail)
Function menu¨p.9
r (voice call), o (V.phone)
3
●
Checking the number of missed calls
■ To check only missed calls in Received calls
XiX“Own data”X“Received calls”
The total number of received calls, the number of
missed calls and the number of unconfirmed missed
calls appear.
When you select “Missed calls”, only the missed calls
appear.
■Icons for redial/dialed calls and received calls
*1
Icon
/ / Incoming and Outgoing/Missed/
Unconfirmed missed voice calls
/ / Incoming and Outgoing/Missed/
Unconfirmed missed international
voice calls
/ / Incoming and Outgoing/Missed/
Unconfirmed missed videophone
calls
/ / Incoming and Outgoing/Missed/
Unconfirmed missed international
*2
・ /
videophone calls
Incoming and Outgoing calls in B
mode of 2in1
/ Record message/Record VP
message
Received calls with Chaku-moji
Incoming and Outgoing/Missed/
Unconfirmed missed packet
/
communication
/ / Incoming and Outgoing/Missed/
Unconfirmed missed 64K data
communication
Description
8
Page 9
*1
Icon
Description
Incoming packet communication
or 64K data communication that is
received without an external
device connected
Incoming and Outgoing calls when
the Time zone is not “GMT+09”
regardless of the “Auto time
adjust” setting (the summer time is
displayed when you set the
summer time)
*1 : Some icons look different between the detail screen
and list screen.
*2 : Displayed only when 2in1 is in Dual mode.
N
z When using 2in1, up to 30 entries for Number A
and for Number B respectively are stored in Redial/
Dialed calls/Received calls regardless of the mode.
<Redial/Dialed calls>
z Activating “Restrict dialing” deletes all Redial/
Dialed calls entries.
z When you make a call by selecting Multi number
from the function menu, the registered name and
number of the additional number are displayed
under the phone number on the Redial screen
(detail)/Dialed calls screen (detail). When you
make a call without using the function menu,
nothing is displayed even when “Set Multi
Number” is set to additional number.
<Received calls>
z “Callback” appears on the Received calls screen
of a voice call for callers who are not stored in the
phonebook and stored in Redial.
z When “Missed calls display” under “Ring time
(sec.)” is set to “Not display” and you receive a call
of which ring tone sounded for a shorter time than
the time set in “Set mute seconds”, the call is not
displayed in Received calls.
z If the caller is using a direct line, a number different
from the direct dialing number may be displayed.
z If the same phone number is registered in multiple
phonebook entries with different names, the
names appear in reading order on the Received
calls screen.
z When you have subscribed to Multi number and
make a call from the Received calls screen, the
phone call is made from the number that received
the call regardless of the “Set Multi Number”
setting.
z When you receive a call for the additional number
of Multi number, the registered name of the
additional number is displayed under the phone
number on the Received calls screen (detail).
Redial/Dialed calls/Received
calls screen (p.8)
Notify Caller ID*1→p. 11
Prefix numbers*1→p. 12
Chaku-moji*1→p. 10
Int’l call*1→p. 7
2in1/Multi Num.*1……Select Number A/Number B/
Cancel number when 2in1 is set to ON in Dual mode
(not available when A mode or B mode is set). When
the 2in1 setting is set OFF, select Basic Number/
Additional Number 1/Additional Number 2/Cancel
number.
Ring time
*2*3
……Display missed call entries with
ringing times.
Add to phonebook
Look-up phonebook
Add desktop icon
Compose message
Compose SMS
*4
Search location……Access the i-mode site and
execute imadoco kantan search using the phone number.
Sent address*5, Received address*3……Display
respective screens.
Select image……Select My side/Chara-den for an
image used during a videophone call. Select
“Release settings” to release the setting.
Big font⇔ Standard font*3……Change the font size
of the displayed name.
Delete……Select Delete this/Delete selected/Delete all.
*1 : Available only on the detail screen.
*2 : Available only on the Received calls screen.
*3 : Available only on the list screen.
*4 : Available only when 2in1 is in A mode or Dual mode,
and a record of A mode is selected.
*5 : Available only on the Redial or Dialed calls screen.
N
z Selecting “Delete all” on the Redial/Dialed calls
deletes all Redial and Dialed calls entries. Note
that selecting “Delete this” or “Delete selected” for
a Redial entry does not delete the entry from
Dialed calls, and selecting “Delete this” or “Delete
selected” for a Dialed calls entry does not delete
the entry from Redial.
Voice/Videophone Calls
Continued on next page
9
Page 10
N
z When 2in1 is set to ON, selecting “Delete all” on
the Redial/Dialed calls/Received calls screen
deletes all Redial/Dialed calls/Received calls
entries in A or B mode regardless of the 2in1 mode.
<Compose message>
z Compose mail with a mail address specified as
the recipient when the mail address is stored in
the phonebook together with the phone number. If
Voice/Videophone Calls
multiple mail addresses are stored, the first
address is used.
Using Chaku-moji
When making a voice call or videophone call, send a
message (Chaku-moji) to the other party to show a
summary of the call, etc. beforehand.
z 5 Chaku-moji messages are stored at the time of
purchase. You can change the pre-installed Chakumoji messages.
z You can include pictograms or face marks in
Chaku-moji, and you can send a message of up to
10 characters including pictograms/symbols/
double-byte characters/single-byte characters.
z For details on Chaku-moji and the compatible
models, refer to the NTT DOCOMO website or
“Mobile Phone User’s Guide [Network Services]”.
<Chaku-moji>
Adding, editing and setting messages
iX“Settings/NW Service”X
1
“Network service”X“Chaku-moji”
XSelect any item:
Create message……Store or edit frequently
used Chaku-moji. Up to 30 Chaku-moji
messages (including 5 pre-installed) can be
stored.
XHighlight an item to store or editX
o (Edit)XEnter Chaku-moji
■ To delete a message
Xu (FUNC)X “Delete”XSelect a deletion
method
MSG display settings……Select Display all
messages/Only number in PH-book/Calls with
Caller ID/Hide all messages as the Chaku-moji
display setting for an incoming call with Chakumoji.
3D message display……Set whether to display
Chaku-moji in 3D animation.
N
z You cannot delete the pre-installed Chaku-moji.
Even when you change a pre-installed Chaku-moji
and delete the Chaku-moji, it is restored to default.
Making a call with a message
You can add Chaku-moji when making a voice or
videophone call from the “Enter phone number”
screen and the detail screen of the “Phonebook”,
“Redial”, “Dialed calls” or “Received calls”.
<Example: To make a voice call with Chaku-moji from
the enter phone number screen>
Enter phone number screen (p.2)
1
Xu (FUNC)X“Chaku-moji”X
Select any item:
Create message……Enter Chaku-moji. Up to
10 characters can be entered.
Select message……Select a stored Chaku-
moji. You can edit Chaku-moji by pressing
o (Edit) on the message selection screen.
Sent messages……Select a previously sent
Chaku-moji. You can edit Chaku-moji by pressing
o (Edit) on the sent message screen.
■ To delete the entered Chaku-moji (to make
a call without Chaku-moji)
Xu (FUNC)X“Chaku-moji”X“Create
message”XClear the entered text
r (voice call), o (V.phone)
2
When the other party’s terminal receives Chakumoji, “Transmission completed” appears.
10
Page 11
N
z Charges apply to send Chaku-moji. Charges do
not apply to receive Chaku-moji.
z Up to 30 sent Chaku-moji can be stored in Sent
messages. (Regardless of the modes in the use of
2in1, up to 30 Sent messages are stored in A and
B numbers, respectively.) When you send the
same Chaku-moji repeatedly, only the latest one is
recorded. When the number of entries exceeds
the maximum, older entries are overwritten.
z If the receiver’s handset is under the following
conditions, Chaku-moji cannot be sent. In this
case, no sending charges apply.
• The handset does not support Chaku-moji
(“Transmission failed” appears)
• Chaku-moji does not appear on the receiver
display due to the “MSG display settings” on the
receiver handset “Transmission failed” appears)
• Public mode (Driving mode) is set
• The ringing time for Record message is set to 0
second
• “ ” is displayed or the power is off
z Depending on the signal quality, the transmission
result may not appear on the sender terminal even
when the receiver terminal receives Chaku-moji.
In this case, sending charges apply.
z You cannot send or receive Chaku-moji overseas.
●
When you receive a voice or videophone
call with a message
The Chaku-moji appears on the ringing screen. The
Chaku-moji disappears when you answer the call.
z The received Chaku-
moji is displayed in 3D
animation.
Chakumoji
Ex: Voice call
N
z Even when you receive a call whose ring tone
sounded for a shorter time than the time set in
“Set mute seconds” under “Ring time (sec.)”,
Chaku-moji is displayed and recorded in Received
calls.
z Some pictograms are not displayed in 3D
animation.
z Depending on the status of the sender or receiver,
Chaku-moji may not be displayed even when you
receive a call with Chaku-moji.
N
z When the Original lock is set on “Chaku-moji”,
Chaku-moji is not displayed even if you receive a
call with Chaku-moji. You can view the Chaku-moji
in Received calls after releasing the lock.
●
Displaying a message from Received calls
When you receive Chaku-moji, the “ ” icon
appears on the Received calls entry, and you can
check the Chaku-moji on the “Received calls” screen
(detail).
N
z Even when you make a call using the Received
calls entry, the Chaku-moji in the entry is not sent.
Showing/Hiding Caller ID When Making a Call
Adding the “186”/“184” prefix to the
other party’s phone number
To show your caller ID, add the “186” prefix when you
dial the phone number. To hide your caller ID, add the
“184” prefix.
■To show your phone number
186 - (The other party’s phone number)
r (voice call) or o (V.phone)
■To hide your phone number
184 - (The other party’s phone number)X
r (voice call) or o (V.phone)
Showing/Hiding your caller ID from the
function menu
Show/Hide your caller ID using the function menu of a
detail screen such as “Enter phone number” screen,
“Phonebook”, “Received calls”, “Dialed calls” or
“Redial”.
<Example: To make a voice call from the Enter phone
number screen>
Enter the phone number of the
1
other party
u (FUNC)X“Notify Caller ID”X
2
“OFF” or “ON”
X
Voice/Videophone Calls
Continued on next page
11
Page 12
■ To release the “Notify Caller ID” setting
X“Cancel prefix”
When “Cancel prefix” is selected, the “Caller ID
Notification” setting applies.
r (voice call), o (V.phone)
3
N
z Some phones may be unable to receive push
signals.
Using the Prefix Function
Sending Touch-tone Signals
Voice/Videophone Calls
Use services such as ticket ordering or checking
bank balances by sending push signals from the
FOMA terminal.
Register dialing data used as push signals to Pause
dial beforehand, then send the data. Inserting p
(pause) into the dialing data allows you to send data
with a separation where a pause lies.
z Only a single entry can be saved.
z You can enter characters from 0 to 9, #, *, and p
(pause) for dialing data.
z You cannot enter p (pause) in succession or at the
beginning of the dialing data.
iX“Settings/NW Service”X
1
“Dialing”X“Pause dial”
■ If there is dialing data already stored
The stored dialing data appears.
When you send the displayed dialing data as is,
go to Step 3.
■ To delete a dialing data
Xu (FUNC)X“Delete”
o (Edit)XEnter dialing data
2
Press 0 to 9, q or w to enter dialing
data.
■ To enter p (pause)
Xw (1 second or longer)
d (Send)XDial the phone
3
number of the destination
A call is made to the entered phone number and
the dialing data up to the first p (pause) is
displayed while the dialed phone is ringing. p
(pause) is not displayed.
r
4
Each time you press r, the dialing data up to
p (pause) is transmitted. When the last number
is sent, the in-call screen reappears.
■ To transmit all dialing data at once
Xj (1 second or longer)X“Send at one time”
It may not be possible to send all the data at
once to some recipients.
12
<Pause dial>
Store prefix numbers such as IDD Prefix code and
186/184 for showing/hiding your caller ID beforehand
and add these prefix numbers when you make calls.
Storing prefix numbers
z Up to 7 prefix numbers can be stored.
z You can enter characters from 0 to 9, #, * and +.
iX“Settings/NW Service”X
1
“Dialing”X“Prefix setting”
■ To delete prefix numbers
Xu (FUNC)XSelect a deletion method
Highlight an item to store or
2
changeXo (Edit)
Enter a name
3
Enter a number (prefix)
4
You can enter up to 10 digits.
Making a call with a prefix number
z You can add prefix numbers on the “Enter phone
number” screen and the detail screen of
“Phonebook”, “Received calls”, “Dialed calls” or
“Redial”.
<Example: To make a voice call by adding a prefix
number on the enter phone number screen>
Enter the phone number of the
1
other party
u (FUNC)X“Prefix numbers”X
2
Select a stored nameXr
<Prefix setting>
<Prefix numbers>
Page 13
Making a Call Specifying a
Sub-Address
<Sub-address setting>
Making the Earpiece Sounds
Clear
<Hyper Clear Voice>
Set whether to specify “*” in the phone number as a
separator so that the digits following “*” are
recognized as a sub-address (ON or OFF).
z Sub-addresses are used in ISDN to identify calls
made from specific communications devices and to
select content in “V-live”.
iX“Settings/NW Service”X
1
“Dialing”X“Sub-address setting”
X“ON” or “OFF”
N
z In the following cases, “*” does not function as a
sub-address separator. The number including “*”
is recognized as an ordinary phone number.
• When “*” is entered at the beginning of a phone
number
• When “*” immediately follows “186” or “184” at
the beginning of a phone number
• When “*” immediately follows a number
entered using “Prefix numbers”
• When the phone number contains “*590#”,
“*591#” or “*592#”
Setting the Alarm for
Reconnection
When the signal quality deteriorates during a voice/
videophone call and the call disconnects, the FOMA
terminal will automatically reconnect the call if the
signal quality quickly improves. Set the type of alarm
when a call is reconnected.
z The time required for reconnection varies
depending on communication conditions or the
signal quality. It takes about 10 seconds.
iX“Settings/NW Service”X
1
“Talk”X“Reconnect signal”X
Select an alarm tone
Select “No tone”, “High tone” or “Low tone”.
N
z Call charges also apply until reconnected (up to
about 10 seconds).
<Reconnect signal>
This function detects ambient noise and makes the
other party’s voice clear during a voice or videophone
call.
z When handsfree is on or an external device such
as earphone/microphone (optional) is connected,
this function is disabled.
In-call screen (p.2), Videophone in-
1
call screen (p.2) X
p ( →→)
Pressing p switches the setting in the
following order: “High”→ “OFF” → “Low”.
Voice call Videophone call
High……Activate the function even when quiet,
regardless of the ambient noise.
Low……Activate the function only when the
ambient noise is high.
OFF……Deactivate the function.
■ To set from the main menu
XiX“Settings/NW Service”X“Talk”X“Hyper
Clear Voice”X“High”, “Low” or “OFF”
N
z This function changes the sound quality or
volume. Change the setting if necessary.
z The effect may vary depending on the other
party’s voice, etc.
z The ambient noise detected via the microphone
activates this function. It may be activated by your
voice.
Voice/Videophone Calls
13
Page 14
Reducing Surrounding Noise to Make Voice Clear
<Noise reduction>
This function suppresses ambient noise and makes it
easier for the other party to hear you during a voice/
videophone call.
Voice/Videophone Calls
iX“Settings/NW Service”X
1
“Talk”X“Noise reduction”X“ON”
or “OFF”
Talking Handsfree While
Driving
You can make or receive voice calls with handsfree
devices by connecting the FOMA terminal to
handsfree devices such as In-Car Hands-Free Kit 01
(optional) or a car navigation system.
For information on how to use the handsfree device,
refer to the manual provided with the device. The
FOMA In-Car Hands-Free Cable 01 (optional) is
required to use the In-Car Hands-Free Kit 01.
N
z To operate from the handsfree device, set the
USB mode to “Communication mode”.
z The display and ring tones used for incoming calls
and mail follow the FOMA terminal settings.
z When the handsfree device is set to emit sounds,
the ring tone comes from the handsfree device
even when in Manner mode or the Ring volume is
set to “Silent”.
z When the Public mode (Driving mode) is set,
operation for incoming calls and mail follows the
“Public mode (Driving mode)” settings.
z When Record message is set, operation for
incoming calls follows the “Record message”
settings.
z When the FOMA terminal is set to emit sounds,
operation when the FOMA terminal is folded
during a call follows “Setting when folded”. When
the handsfree device is set to emit sounds, folding
the FOMA terminal does not affect the call status
regardless of the “Setting when folded” setting.
<In-car hands-free>
Receiving a Voice/ Videophone Call
Receive a voice or videophone
1
call
The ring tone sounds and the illumination
flashes.
■ When you receive a call with Chaku-moji
The Chaku-moji appears on the ringing screen
or videophone ringing screen. →p. 11
Ringing
Function menu¨p.15
■ To put a voice/videophone call on hold
while ringing→ p.18
r
2
■ To answer a videophone call with the
substitute image
Xd (Subst.)
■ Operations during a videophone call
You can perform various operations such as
changing the camera image to the substitute
image and muting sounds during a videophone
call.→ p.2
■ To set Hyper Clear Voice →p.13
■ When the other party switches a voice/
videophone call during a call→p.16
■ To put the current voice/videophone call
on hold→ p.18
To end the call, press y
3
Videophone ringing
Function menu¨p.15
14
Page 15
Display while receiving a call
■When the other par ty’s phone number is
notified
The other party’s phone number appears on the
screen. When the caller is stored in the
phonebook, the name stored in the phonebook
appears (only the name is displayed while
Keypad lock is set with “Security code” set to
“YES”).
z If the same phone number is registered in
multiple phonebook entries with different
names, the first name retrieved by Search
reading appears.
z If the caller is stored as secret data, the name,
etc. do not appear but only the phone number
appears.
z When you receive a call for the additional
number of Multi number, the registered name
of the additional number is displayed on the
ringing screen.
■When the other par ty’s phone number is
not notified
The reason appears.
■If Callback appears
“Callback” appears on the ringing screen for
callers who are not stored in the phonebook and
stored in Redial.
Ringing screen/Videophone
ringing screen (p.14)
Call Rejection……Terminate the incoming call
without answering it.
Call Forwarding……Forward the call to the
forwarding number regardless of the Activate/
Deactivate setting of Call Forwarding.
Voice Mail……Connect the call to the voice mail
service center regardless of the Activate/Deactivate
setting of Voice Mail.
Change Display……Switch the display from the
additional number 1 or 2 to the number from which
the call is forwarded. This can be selected when the
received multi number call (for additional number 1 or
2) was forwarded.
N
z You can use an earphone/microphone (optional)
to receive a call.
z If you have subscribed to the Call waiting, Voice
mail or Call forwarding service and you activate
“Set in-call arrival” and set “Arrival Call Act” to
“Answer”, you will hear a short double beep
(“bibip”) when you receive a call during a call.
• If you subscribe to the Voice Mail or Call
Forwarding service, you can answer a call after
ending the current call.
• If you subscribe to the Call Waiting service, you
can answer a voice call after putting the current
call on hold, and you can answer a videophone
call after ending the current call.
z You can set the operation for calls from callers not
stored in the phonebook.
z You can set restrictions for each phone number
stored in the phonebook.
<Videophone>
z You can also answer a call by pressing
o (V.phone).
z It may take a few seconds to switch from the
camera image to the substitute image (Charaden) depending on the Chara-den.
Voice/Videophone Calls
15
Page 16
When the Other Party Switches a Voice/Videophone Call
When you receive a voice/videophone call, the other
party can switch between voice call and videophone
call.
Voice/Videophone Calls
z The receiver cannot switch the call.
z To switch calls, the receiver needs to set “Ntfy
switch-mode” beforehand.→ p.24
z You can use this function with terminals compatible
with voice call/videophone call switch.
<Example: When the other party switched a voice call
to a videophone call>
In-call screen (p.2)XThe other
1
party switches to a videophone
call
X“YES”
During switching, a screen appears indicating
that the calls are being switched, and voice
announcement is played.
When a voice call is switched to a videophone
call, the camera image is sent to the other party.
■ To send substitute image to the other
party
X“NO”
Pressing a Dial Key to
Answer a Call
Tur n off the ring tone or answer an incoming call
quickly.
iX“Settings/NW Service”X
1
“Incoming call”X“Answer
setting”
Any key answer……Press any of the following
keys to answer voice calls:
r, d (Talk), 0 to 9, w, t, o,
p, a (マナー ), b (voice calls)
* You can answer a videophone call only by normal key
Quick silent……Stop the ring tone while the
caller continues to hear the ringback tone by
opening the FOMA terminal or pressing any of
the following keys:
0 to 9, w, t, b, p, a ( マナー) or
o (voice calls)
To answer the call, press r, d (Answer/Subst.)
or o (V.phone).
OFF……Answer a call only by normal key
operations.
r, d (Answer/Subst.), o (V.phone)
N
z Even when set to “Quick silent”, “Any key answer”
is active in Manner mode.
z “Any key answer” or “Quick silent” does not work if
you press 5 (ECO mode ON/OFF) or 8
(Privacy angle ON/OFF) for 1 second or longer.
z When set to “Any key answer”, a voice call is put
on hold if a (マナー ) is pressed with the FOMA
terminal folded. The hold tone sounds with
“Setting when folded” set to “Tone on”, but does
not sound when set to “No tone” or “End the call”.
XSelect any item:
operations (r, d (Subst.) or o (V.phone)).
<Answer setting>
■ When switching a videophone call to a
voice call
XVideophone in-call screen (p.2)XThe other
party switches to a voice call
The videophone call is switched to the voice call.
16
Page 17
Ending/Holding Call by Folding the FOMA Terminal
<Setting when folded>
Set the operation to be performed when the FOMA
terminal is folded during a voice or videophone call.
iX“Settings/NW Service”X
1
“Talk”X“Setting when folded”X
Select any item:
No tone……Mute the sound. For videophone
calls, “Substitute image” is sent to the other
party. The other party does not hear the hold
tone.
Tone on……Put the call on hold (holding). While
the terminal is folded, the other party hears the
hold tone. For videophone calls, the call hold
image is sent to the other party.
Speaker ON……Send the hold tone to the
other party and also play it through the
speaker.
Speaker OFF……Send the hold tone to the
other party only.
End the call……End the call. This is the same
operation as pressing y.
Adjusting Earpiece Volume
<Volume>
On the standby screenX
1
c (1 second or longer)XUse c
to adjust volume
Pressing c (1 second or
longer) displays the earpiece
volume screen. If no
operation is performed for 2
seconds or longer while the
earpiece volume screen is
displayed, earpiece volume
adjustment ends.
Adjust the volume between 6 steps from
“Level 1” (quietest) to “Level 6” (loudest).
■ To adjust the earpiece volume during a
call
During a voice call: c (1 second or longer)
During a videophone call: c
• a ( マナー) or s (C) is also available to adjust
volume.
N
z The volume setting adjusted during a call is
retained after you end the call.
Voice/Videophone Calls
N
z In Manner mode, no sound comes from the
speaker even if set to “Speaker ON”.
z When an earphone/microphone (optional) is
connected, this function is disabled.
z Even if set to “Tone on”, folding the FOMA
terminal activates “No tone” when “Call Waiting” is
switched on.
z If you fold the FOMA terminal after putting a call
on hold by pressing Wt, the “Tone on” setting is
disabled.
Adjusting Ring Volume
<Ring volume>
Adjust the ring tone volume for incoming call, mail,
MessageR/F or i-concier information between 6 steps.
You can also mute or gradually increase volume.
iX“Settings/NW Service”X
1
“Incoming call”X“Ring volume”X
Select an item to adjust the
volume
Select “Phone” to adjust ring tone volume for
voice calls and 64K data communication.
Select “Mail” to adjust the ring tone volume for
i-mode mail, Area Mail, SMS and packet
communication.
Use c to adjust volumeXd (Set)
2
■ To increase volume gradually
XPress f at “Level 6”
When set to “Step”, the ring volume increases
every 3 seconds.
17
Page 18
■ To mute the ring tone
XPress g at “Level 1”
The icon on the standby screen indicates which
items are set to “Silent”.
: “Silent” is set for “Phone” and/or
“Videophone”
: “Silent” is set for “Mail”, “MessageR” and/or
“MessageF”
Voice/Videophone Calls
: Both “ ” and “ ” are set
N
z The ring volume setting specified for “Phone” in
this function is also applied to the “Select ring
tone” setting for a voice call, and the alarm tones
for “Schedule” and “To Do list”.
Setting the hold tone
Set the announcement to be played to the caller
during on hold.
z You cannot change the hold tone played during a
call.
iX“Settings/NW Service”X
1
“Talk”X“Hold tone setting”X“On
hold tone”
Select “Tone 1”, “Tone 2”, “Voice announce 1*” or
“Voice announce 2
*: Not available when no voice announcement is
recorded.
XSelect a tone
*
”.
<Hold tone setting>
Holding Incoming/Current
Calls
<Example: To put an incoming call on hold>
While ringingXy
1
Three short beeps sound
and the call is put on hold.
The caller hears an
announcement that you
cannot answer now, and the
call is put on hold.
■ To put the current call
on hold
XDuring a callXt
■ To end the call during on hold/call hold
Xy
Press r to resume the call
2
You can also press t to resume the held call.
N
z Call charges apply while an incoming call or
current call is put on hold.
<On hold/Holding>
Using Public Mode
Public mode (Driving mode/Power OFF) is an
automatic answering service provided for public
places and circumstances in which mobile phones
should not be used.
z When Public mode and network services are set
concurrently, Voice Mail service
*1
service
and Caller ID Request service*2 take
precedence over Public mode.
*1 : For a voice call whose ring time is not “0 second”, a
service activates after the Public mode
announcement is played.
*2 : When the caller notifies the caller ID, Public mode
activates.
z Public mode does not work for a call from a phone
number registered for Nuisance Call Blocking.
Using Public Mode (Driving Mode)
When Public mode is set, a caller hears a message
that you cannot answer the call because you are
driving or in a place where you have to refrain from
using a mobile phone (on a train or bus, in a theater,
etc.), then the call ends.
z Public mode can only be set or released from the
standby screen (can also be set or released when
“ ” is displayed.).
z You can make calls when Public mode is set.
z This function is not available during data
communication.
z When you receive a call with no caller ID while
Caller ID Request service is set to “Activate”, the
caller ID request announcement is played (Public
mode announcement is not played.)
<Public mode (Driving mode)>
*1
, Call Forwarding
18
Page 19
On the standby screenX
1
w (1 second or longer)
Public mode is set and “ ”
appears.
When you receive a call, the
caller hears the
announcement “The person you are calling is
currently driving or in an area where cellphones
should not be used. Please try again later.”
■ To release Public mode (Driving mode)
XOn the standby screenXw (1 second or
longer)
Public mode is released and “ ” disappears.
N
z The Public mode setting takes priority even when
“Record message” is “ON”.
z The Public mode setting takes priority when
Manner mode is set at the same time.
z If you make an emergency call using a voice call
(110, 119 or 118) while Public mode is set, Public
mode is released.
z The following tones do not sound in Public mode:
• Ring tone for voice call/videophone
• Ring tone for mail and message
• Various alarm tones
• Wake-up tone
• Open-Close sound
• Charge sound
• Software tone for i-αppli
• Ring tone for packet communication/64K data
communication
●
When Public mode (Driving mode) is set
The ring tone does not sound when a voice call or
videophone call arrives. Calls are logged as “Missed
calls” in “Received calls”, and the “Missed call”
desktop icon appears on the standby screen.
z A voice caller hears a message that you cannot
answer the call because you are driving or in the
place where you have to refrain from using a
mobile phone, and then the call ends.
z A videophone caller sees the Public mode video
message on his or her display, and then the call ends.
z When you receive mail, the ring tone does not
sound and the “New mail” desktop icon appears on
the standby screen.
N
z If the power is off or “ ” is displayed, the
announcement for “ ” is played instead of the
Public mode message even when Public mode is
set.
Using Public Mode (Power OFF)
When Public mode (Power OFF) is set, a caller who
made a call while the power is off hears a message
that you cannot answer the call because you are in a
place where you have to turn off the mobile phone (in
a hospital, on an airplane, around a priority seat on a
train, etc.), then the call ends.
On the standby screenX
1
w25251Xr
Public mode (Power OFF) is set (Nothing
changes on the standby screen).
When you receive a call after setting Public
mode (Power OFF) and turning off the power,
the caller hears the announcement “The person
you are calling is currently in an area where use
is prohibited. Please try again later.”
■ To release Public mode (Power OFF)
XOn the standby screenX
w25250Xr
■ To check the Public mode (Power OFF)
setting
XOn the standby screenX
w25259Xr
●
When Public mode (Power OFF) is set
The setting is valid until “*25250” is dialed to release
Public mode (Power OFF). The setting is not released
by simply turning on the power.
The Public mode (Power OFF) announcement is
played even when you are out of service area or
where the reception is very poor.
z A voice caller hears a message that you cannot
answer the call because you are in a place where
you have to turn off the mobile phone, and then the
call ends.
z A videophone caller sees the Public mode (Power
OFF) video message on his or her display, and
then the call ends.
<Public mode (Power OFF)>
Voice/Videophone Calls
19
Page 20
When You Cannot Answer an
Incoming Call
When you could not answer an incoming call,
appears on the standby screen. When you select ,
you can check the date, time and caller’s name of the
call.
Voice/Videophone Calls
On the standby screenXdX
1
Select “ ”
The “Missed call list” screen appears.
To check information with the FOMA
terminal folded
When there is a missed call or new mail (i-mode mail,
Area Mail, SMS), the incoming call lamp keeps
flashing. Press s (C) to sound the short tone.
Press s (C) with the FOMA
1
terminal folded
A short tone notifies you of the information in
accordance with “Info notice setting”.
●
Flashing of the Incoming call lamp
When there is a missed call, new mail or other
information, the incoming call lamp keeps flashing in
the respective color set in “Illumination”.
z Phone/Videophone: Color set for “Phone”
z New mail: Color set for “Mail”
■Flashing colors and conditions
z The lamp does not flash when “Missed info” under
“Illumination” is set to “OFF”.
z When “Gradation” under “Illumination” is set, the
lamp flashes in the default color.
z You can configure individual illumination settings in
the phonebook.
z The lamp does not flash in Public mode (Driving
mode).
■To turn off the lamp
z Select the icon for “Missed call” or “New mail” on
the display to check information, or press
t (1 second or longer).
<Missed call>
Setting the notification method for
missed calls
Set the notification method to be performed when
s (C) is pressed with the FOMA terminal folded.
z The setting items and notification methods using
s (C) are as follows:
z The “ボイス ” (Voice) option is available in
Japanese mode, which reads out the information of
incoming calls and messages (voice monitor), or
the current time (voice clock).
■When there is a missed call, new mail, etc.
Setting
Tone and
item
ON The “Pipip,
■When there is no missed call, new mail, etc.
Setting
item
ON The “pipipip”
*1 : Vibration works when “Phone” of “Vibrator” is not set
to “OFF”.
*2 : When the color of “Illumination” is set to “Gradation”,
the lamp flashes in the default color.
iX“Settings/NW Service”X
1
“Incoming call”X“Info notice
setting”
N
z This function alerts you using a “YES” indication
when a desktop icon such as “Missed call” or
“New mail” is displayed on the standby screen.
z You cannot use s (C) to check for missed calls or
new mail in the following cases:
• When Side key guard is set to “ON”
• When playing music with Music Player/
Music&Video Channel
z The volume is determined by “Phone” under “Ring
volume” (Played at “Level 2” when set to “Silent”
or “Step”).
z Opening the FOMA terminal during notification
stops the notification.
*1
vibration
pipip” tone
plays.
Tone and
*1
vibration
tone plays.
XSelect “ON” or “OFF”
<Info notice setting>
Illumination
The incoming call lamp
lights for about 6 seconds
in the color set for
“Illumination”.
If there are different types
of information such as call
and mail, the lamp changes
to each of the
corresponding color at
1-second intervals.
Illumination
The lamp flashes in “Color
12” for about 6 seconds.
*2
20
Page 21
Recording Voice/Video
Messages When You Cannot
Answer the Call
Have the caller leave a message on your FOMA
terminal when you cannot answer a voice or
videophone call.
z Each message can be up to 20 seconds long, and
5 messages can be recorded for voice calls and 2
messages can be recorded for videophone calls.
Setting Record message
iX“Settings/NW Service”X
1
“Incoming call”X“Record
message”
ON……Select Japanese 1/Japanese 2/English/
Voice announce 1
OFF……Release the Record message setting.
*: Not available when no voice announcement is
recorded.
Enter the ringing time (000 to 120
2
seconds in 3 digits)
Record message is set, and “ ” and “ ”
appear on the standby screen.
N
z To give priority to the “Record message” function
when “Voice Mail”, “Call Forwarding” and “Record
message” are set simultaneously, set the ringing
time of Record message shorter than that of Voice
Mail and Call Forwarding.
z If the mute time set for “Ring time (sec.)” is longer
than the ringing time set for Record message,
Record message activates without ringing. To
activate Record message after ringing, set the
Record message ringing time longer than the
mute time.
z You can use “Ring tone/Image” (individual) to set
an answer message for each phone number and
“Ring tone/Image” (group) to set an answer
message for each group.
XSelect any item:
<Record message>
*
/Voice announce 2*.
When “Record message” is set to
“ON” and you receive a call
Record message activates when the set time has
elapsed.
z The voice caller hears the answer message, and
recording starts.
z To a videophone caller, the “ 伝言メモ準備中
Preparing” image is sent, the answer message is
played, the “伝言メモ録画中 Recording” image is
sent, then recording starts.
■When message recording starts
z The recording screen appears. The caller’s voice
can be heard through the FOMA terminal earpiece
during recording.
■To answer a voice call during
recording
Xr
■To answer a videophone call
during recording
XPress r to answer with the
camera image or d (Subst.) to
answer with the substitute image
■When message recording ends
z The previous screen reappears
and the “Missed call” desktop
icon and “Record message”/
“Record VP message” desktop
icon appear on the standby
screen. You can check the
content by selecting one of the
desktop icons.→ p.2 2
z The number of recordings is indicated by icons in
the icon display area at the top of the screen.
- : Record message (the number indicates
the number of messages)
/ : Record VP message (the number
indicates the number of messages)
* When Auto voice memo is set to ON, the following
icons appear but the number of messages d oes not:
: Record message
: Record message and Auto voice memo
N
z When Manner mode is set, you cannot hear the
caller’s voice during recording.
z You cannot answer another call during recording.
Ex. Voice call
Voice/Videophone Calls
21
Page 22
Recording a Message When
You Cannot Answer Incoming
call
Even when “Record message” is not set to “ON”, you
can record a message while receiving a call by
pressing a key.
Voice/Videophone Calls
While ringingXs (C)
1
Message recording starts.
■ To set Manner mode when recording
starts
XWhile ringingXq
N
z You cannot set “Record message” to “ON” with
this operation.
z When the messages are full and you receive a
voice or videophone call, Record message does
not activate and the FOMA terminal keeps on
ringing (when q is pressed, the ringing
continues in accordance with the “Manner mode
set” setting).
<Quick mes sage>
Playing/Deleting Record Messages/Voice Memos/ Moving Picture Memos
z When there is an unplayed recorded message,
“ ” (Record message) or “ ” (Record VP
message) appears on the standby screen.
<Example: To check an unplayed recorded message>
On the standby screenXdX
1
Select “ ” (Record message) or
“ ” (Record VP message)
“★ ” appears for items
recorded.
■ To play a message with
a menu operation
XiX“LifeKit”X“Play/
Erase msg.” or “Play/Erase
VP msg.”
■ To erase a recorded message or voice
memo
Xu (FUNC)XSelect a erasing method
Play/Erase msg.
Select an item to play
2
<Record message/Voice memo/Auto voice
memo>
A beep sounds and playback starts. When the
playback ends, two short beeps sound and the
“Play/Erase msg.” screen reappears.
You can also play a message by pressing
Ss (DC) on the standby screen with the FOMA
terminal folded.
■ To play the next message while playing
a message
XSs (DC)
Each time you press Ss (DC), the messages are
played in the following order: Record message
→Voice memo →Auto voice memo.
■ To stop playback
XXd (Stop) or Wt
The “Play/Erase msg.” screen reappears.
<Record VP message>
Playback starts. When the playback ends, the
“Play/Erase VP msg.” screen reappears.
■ To play another message while playing a
message
XXv
■ To adjust volume while playing a
message
XXc
■ To switch the speaker on/off while
playing a message
XUu (FUNC)X“Speaker ON” or “Speaker
OFF”
■ To pause playback
XXd (Stop)
To resume playback, press Xd (Play)
■ To stop playback
XWt
The “Play/Erase VP msg.” screen reappears.
■ To make a voice call or videophone call to
the displayed phone number during
playback
Xp (voice call
*: The “Phone number entry” screen (p.2) appears.
For subsequent steps, refer to “Making a Voice/
Videophone call” (p.2).
■ To erase a message being played
Xu (FUNC)X“Erase”X“YES”
*
), o (V.phone)
22
Page 23
N
z When 2in1 is in A mode or B mode, “ ★” does not
appear for a recorded message of the unused
phone number. To play the memo, change the
mode or set it to Dual mode.
Setting Videophone Functions
iX“Settings/NW Service”X
1
“Videophone”
Using Chara-den
Send a cartoon character instead of your own image
when you make a videophone call.
z You can display your favorite Chara-den if you set
“Substitute image” under “Select image” to “Charaden” beforehand.
You can also use Chara-den by setting Chara-den
in a phonebook entry or as Ring tone/Image.
z To switch from the camera image to Chara-den
during a videophone call, select “Substitute image”
from the function menu.
When you receive a videophone
1
call, press d (Subst.)
Control your character by
2
pressing dial keys
Chara-den
Pressing a dial key makes the character perform
the action assigned to the key.
Videophone settings
Select any item:
2
Visual preference……Select Normal/Prefer img
qual/Prefer motion spd.
Select image→p.24
Auto redial as voice……Set whether to switch
to a voice call when a videophone call cannot be
made (ON or OFF).
Display setting……Set an image to display on
the main display or how to display your own
camera image.
Main display……Select Other side/My
side as an image to display on the main
display.
Front camera Reverse……Set whether to
display your camera image as a mirror
image (ON) or normal image (OFF) on your
FOMA terminal.
Ntfy switch-mode→ p.24
Hands-free switch……Set whether to switch to
handsfree automatically when starting a
videophone call (ON or OFF).
V.phone while packet→ p.24
Voice/Videophone Calls
23
Page 24
Setting an image to send during
videophone calls
Set an image to send instead of the camera image.
z You can set a JPEG image whose file size is 100
KB or less and not larger than 854 dots wide × 854
dots high, or a GIF image whose file size is 100 KB
or less and not larger than 854 dots wide × 480
dots high or 480 dots wide × 854 dots high (except
Voice/Videophone Calls
file-restricted images).
Videophone settings screen (p.23)
1
X“Select image”XSelect any item:
On hold, Holding, Substitute image, Record
message, Preparing, Voice memo
Select an image to send
2
Pre-installed……Send only a message.
Original……Send an image and message. To
change the image, select “Change setting” from
the function menu then select an image from My
picture.
Chara-den*……Send the image selected as
“Substitute image”.
To change the Chara-den, select Change setting
from the function menu then select Chara-den
from the Chara-den list.
*: Available only when “Substitute image” is selected.
<Select image>
Setting switch between a voice call
and videophone call
Set whether to let the other party know that your
FOMA terminal supports switching between a voice
call and videophone call.
z Calls cannot be switched when set to “Indication
OFF”.
z You cannot set this function during a call/when you
are out of range.
Videophone settings screen (p.23)
1
X“Ntfy switch-mode”XSelect any
<Ntfy switch-mode>
item:
Indication ON, Indication OFF……Activate/
Deactivate Ntfy switch-mode.
Check Indication……Display the “Ntfy switch-
mode” setting status.
Setting the answer mode for a
videophone call incoming during
i-mode
z As the multi access function cannot be used for
videophone, incoming videophone calls during
i-mode communication or while sending or receiving
mail are handled according to this setting.
Videophone settings screen (p.23)
1
X“V.phone while packet”XSelect
<V.phone while packet>
any item:
V.phone priority……Switch to the videophone
ringing screen. When you answer the incoming
videophone call, i-mode communication is
disconnected.
Packet downld priority……Reject the incoming
videophone call.
V.phone answerphone……Connect the call to
the Voice Mail service center if you have
subscribed to the Voice Mail service regardless
of the Activate/Deactivate setting of Voice Mail. If
you have not subscribed to this service, “Packet
downld priority” applies.
Call forwarding……Forward the call to the
forwarding number if you have subscribed to the
Call Forwarding service, regardless of the
Activate/Deactivate setting of Call Forwarding. If
you have not set a forwarding number or
subscribed to this service, “Packet downld
priority” applies.
N
<Visual preference>
z If the signal quality deteriorates during a
videophone call, the image may become grainy or
patchy regardless of the settings in “Visual
preference”.
<Select image>
z If you delete the original still image, the “Pre-
installed” image is displayed (sent).
z When the Chara-den character set as the
substitute image is deleted and the “Chara-den”
substitute image cannot be displayed, the preinstalled “ビーンズ (Beans)” is sent. If you delete
the pre-installed “ビーンズ (Beans)”, the “Preinstalled” substitute still image is sent.
24
Page 25
N
<Auto redial as voice>
z When a videophone call is switched and redialed
as a voice call, not digital communications
charges but voice call charges apply.
z When a call is redialed, only the voice call is
logged in “Redial”/“Dialed calls”.
z Even if “Auto redial as voice” is set to “ON”, dialing
may not be possible depending on the network or
other party, e.g. the line is busy.
<Hands-free switch>
z Even when “Hands-free switch” is set to “ON”,
handsfree does not activate automatically in the
following cases:
• While Manner mode is set
• When an earphone/microphone (optional) is
connected (the microphone operation is in
accordance with “Headset mic. setting”)
• When holding a call or Record message is
activated for an incoming call
<V.phone while packet>
z Even when “V.phone priority” is set, you cannot
answer a videophone call if you are using multi
access such as i-mode communication during a
voice call.
z When set to “Packet downld priority”, “V.phone
answerphone” or “Call forwarding”, received
videophone calls are recorded as “Missed calls” in
“Received calls”.
z Even when set to “V.phone priority” or “Packet
downld priority”, the “Voice Mail” or “Call
Forwarding” service is activated if the ring time for
the “Voice Mail” or “Call Forwarding” service is set
to 0 second.
Decorating the videophone call screen
Decorate your videophone call screen (your camera
image) with a stamp and frame.
Videophone in-call screen (p.2)X
1
u (FUNC)X“Decoration”X
<Decoration>
Select any item:
Frame……Select a frame from the Frame
selection screen.
Stamp……Select a stamp from the Stamp
selection screen and decide the paste position.
■ To erase a frame or stamp
Select “Off decoration” from the function menu of
the videophone in-call screen.
N
z If “Front camera Reverse” is set to “OFF” for your
camera image, the decoration is displayed
normally, and a stamp with text can be read
correctly.
Sending a message during a
videophone call (sending camera
image)
Videophone in-call screen (p.2)
1
Xu (FUNC)X“Petit message”X
<Petit message>
Enter a message
The message is displayed. The message
disappears automatically in approximately 15
seconds.
■ To cancel entering a message in text entry
XErase the messageXt
■ To erase the message manually after it is
displayed
Xt (1 second or longer)
You can also erase a message by selecting “Off
decoration” from the function menu.
N
z If “Front camera Reverse” is set to “OFF” for your
camera image, the decoration is displayed
normally, and text can be read correctly.
Voice/Videophone Calls
25
Page 26
Using Videophone Call by Interfacing to External Device
You can make or receive videophone calls from
external devices such as a PC by connecting the
FOMA terminal to the device using the FOMA USB
Cable with Charge Function 02 (Optional).
To use this function, you have to install a videophone
Voice/Videophone Calls
application on the dedicated external device or PC
and prepare commercially available devices such as
an earphone/microphone and USB compatible Web
camera.
z Set USB mode to “Communication mode”. No
specific settings are required to connect external
devices.
z For details on the operating environment, settings,
operating procedure of the videophone application,
refer to the manuals supplied with the external
devices.
z “ドコモテレビ電話ソフト” (DOCOMO Videophone
Software) (Japanese) is compatible with this
function.
Download the software from the NTT DOCOMO
website (Japanese).
N
z You cannot make a videophone call from the
external device during a voice call.
z When you have subscribed to Call Waiting, Voice
Mail or Call Forwarding and you receive a
videophone call from an external device during a
voice call, you can answer the call after ending the
current call. When you receive a voice call,
videophone call or 64K data communication
during a videophone call from the external device,
you can answer the call in the same way.
26
Page 27
Radio Frequency (RF) Signals
THIS MODEL PHONE MEETS THE U.S. GOVERNMENT’S REQUIREMENTS FOR EXPOSURE TO
RADIO WAVES.
Your wireless phone contains a radio transmitter and receiver. Your phone is designed and
manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the
Federal Communications Commission of the U.S. Government. These limits are part of comprehensive
guidelines and establish permitted levels of RF energy for the general population. The guidelines are
based on standards that were developed by independent scientific organizations through periodic and
thorough evaluation of scientific studies.
The exposure standard for wireless mobile phones employs a unit of measurement known as the
Specific Absorption Rate (SAR). The SAR limit set by the FCC is 1.6W/kg.* Tests for SAR are
conducted using standard operating positions accepted by the FCC with the phone transmitting at its
highest certified power level in all tested frequency bands. Although the SAR is determined at the
highest certified power level, the actual SAR level of the phone while operating can be well below the
maximum value. This is because the phone is designed to operate at multiple power levels so as to
use only the power required to reach the network. In general, the closer you are to a wireless base
station antenna, the lower the output.
Before a phone model is available for sale to the public, it must be tested and certified to the FCC that
it does not exceed the limit established by the U.S. government-adopted requirement for safe
exposure. The tests are performed on position and locations (for example, at the ear and worn on the
body) as required by FCC for each model. The highest SAR value for this model phone as reported to
the FCC when tested for use at the ear is 0.503 W/kg, and when worn on the body, is 0.432 W/kg.
(Body-worn measurements differ among phone models, depending upon available accessories and
FCC requirements). While there may be differences between the SAR levels of various phones and at
various positions, they all meet the U.S. government requirement.
The FCC has granted an Equipment Authorization for this model phone with all reported SAR levels
evaluated as in compliance with the FCC RF exposure guidelines. SAR information on this model
phone is on file with the FCC and can be found under the Display Grant section at https://
gullfoss2.fcc.gov/oetcf/eas/reports/GenericSearch.cfm after search on FCC ID A98-KEG4809.
For body worn operation, this phone has been tested and meets the FCC RF exposure guidelines
when used with an accessory designated for this product or when used with an accessory that
contains no metal and that positions the handset a minimum of 1.5 cm from the body. Non-compliance
with the above restrictions may result in violation of FCC RF Exposure guidelines.
* In the United States, the SAR limit for wireless mobile phones used by the public is 1.6 watts/kg (W/kg) averaged
over one gram of tissue. SAR values may vary depending upon national reporting requirements and the network
band.
1
Page 28
FCC Regulations
This mobile phone complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
This mobile phone has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation; if this
equipment does cause harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could void
the user’s authority to operate the equipment.
2
Loading...