NEC of America 7N2R13A Users manual

Making a Voice/Videophone
Call

* As N-03A is not equipped with the front camera,

during a videophone call, you can send only the
substitute image (Chara-den) or image from the
rear camera to the other party.
You can change the substitute image (Chara­den) to other data such as an image of My picture
in “Select image”.→P. 7 1

Enter the phone number of the other

1

party

The “Enter phone number
screen” appears.
Always start by entering the
area code, even for calls
within the same area.
You can enter up to 80 digits
for the phone number.
However, only the last 26
digits are displayed.

<When you enter a wrong number>

■ To insert a number

Press v to move the cursor to the number to
the left of the position where you want to insert
the number, then enter the number.

■ To delete a number

Press v to move the cursor to the number you
want to delete, then press t.
Hold down t for 1 second or longer to delete
all the numbers to the left of the cursor and the
number in the cursor position.

■ To re-enter the number

Move the cursor to the beginning or end of the
number and hold down t for 1 second or
longer to return to the standby screen.

<Videophone>

■ To change the substitute image (Chara-

den)

XFu (FUNC)X“Select image”X“Chara-den”
XSelect Chara-den

Enter phone number

Function menu¨P. 3

r (voice call) /o (V. phone)

2

<Voice call>

The “In-call screen”
appears.
“ ” flashes while dialing
and lights up during the
call.

■ If you hear the busy

tone

The line is busy. Call again
after a while.

■ If you hear a message saying that the

other party cannot be reached

The other party’s mobile phone is not turned
on or is out of signal range. Call again after a
while.

■ If you hear a message requesting your

caller ID

Call again with caller ID notification enabled.
→PP.48, 59

<Videophone>

The “Videophone in-call
screen” appears.
“ ” flashes while dialing
a videophone call and
lights up during the call.

■ If a videophone call is
not connected→ P. 2

■ To switch between
substitute image and
camera image

XFDd (Change)

Each time you press FDd (Change), the
substitute image and camera image switches.

■ To switch the main screen

XDd (1 second or longer)

“Change main disp.”→P. 3

■ To enlarge the camera image to be sent

XAdjust the zoom using Fv

Zoom→ P.138

■ To mute the voice to send

XSa (マナー ) (1 second or longer)

The “ ” icon is displayed.
To cancel muting, press Sa ( マナー ) for 1

second or longer again.

Videophone in-call

Function menu¨P. 3

In-call

1

■ To switch a voice/videophone call during a
call→ P. 3

■ To put the current voice/videophone call
on hold→ P. 6 5

■ When the 2in1 is in Dual mode

The Outgoing number selection screen appears.
Select a phone number.

To end the call, press y

3

● If a videophone call is not connected

When a videophone call is not connected, the cause
of the failure appears.

z The cause may not appear depending on the

situation.

z Depending on the type of other party’s phone or the

possible lack of a network service subscription, the
reason may not accurately reflect the other party’s
actual status.

Display Cause

Check number then
redial

Busy The line is busy

Busy with packet
transmission

Out of service area/
power off

Your call is being
forwarded

Redial using voice
call

Please activate
caller ID before
dialing again

This number is not
available

Upper limit has been
exceeded
Connection failed

Connection failed Set the caller ID notification to

The called phone number is not
used

• This message may also
appear during packet
communication.

The other party is using packet
communication

The other party is out of service
area or the phone is turned off

The call is being forwarded (A
Videophone call is made when
the forwarding number is for a
3G-324M-compatible
videophone)

The phone for the forwarding
number is not compatible with
videophone calls

The other party sets the Caller
ID request service

The other party sets the
Nuisance call blocking service

The upper limit set for a Limit
billing plan (Type Limit and
Family Wide limit) is exceeded

“ON” and retry
You connected without notifying
your caller ID (when dialing into
visualnet, etc.)

• This message may also
appear in other situations

Display Cause

Please make your
call from the i-mode
web page

You attempted to make a
videophone call to watch V-live
without browsing the i-mode
official site

z If the videophone call is not connected, your call is

automatically switched to a voice call when you set
“Auto redial as voice” to “ON”. However, the call
may not be handled in this way if you call an ISDN
synchronous 64K or an ISDN videophone which
does not support the 3G-324M standard (as of
May, 2008) or if you dial a wrong number. Note that
call charge may be applied in some cases.

2

Switching a Voice/
Videophone Call during a Call
(Caller)

z You can use this function with the terminals

compatible with voice call/videophone call switch.

z You can switch the voice call only when you are the

caller.

z To switch the call, the receiver needs to set “Ntfy

switch-mode” to notify the switch beforehand.
→P. 7 2

<Example: To switch a voice call to a videophone
call>

In-call screen (P.1)Xd (V. phone) X

1

“YES”

While switching, the screen which indicates that
the calls are being switched appears and the
voice guidance is played.

Making International Calls

<WORLD CALL>

WORLD CALL is an international dialing service that
can be used from DOCOMO mobile phones.
FOMA service subscribers are also subscribed to
“WORLD CALL” when they subscribe to the FOMA
service. (This excludes subscribers who declared that
they did not require the service.)

z WORLD CALL can be used to call around 240

countries and regions worldwide.

z The “WORLD CALL” is charged with your monthly

call charges.

z In addition to dialing a phone number, you can

make an international call by adding “+” or
selecting “Int’l call” or “Prefix numbers” from the
function menu in the enter phone number screen,
Redial/Dialed calls screen, Received calls screen
or Phonebook detail screen.

z This service is not available in some payment

plans.

For additional information regarding WORLD
CALL, refer to the contact information provided on
the back of the manual.

“International videophone calls” can be made to
users of some specific overseas 3G mobile
terminals by pressing o (V. phone) to make the
call after using the dialing procedure below.

z See the DOCOMO website for information on

accessible countries and operators.

z Depending on the other party’s terminal, the image

of the other party displayed on your FOMA terminal
may be distorted or the connection may fail when
making a international videophone.

The digital
communication fee
is charged after the
appearance of this
screen.

■ To switch a videophone call to a voice call

XVideophone in-call screen (P.1)Xu (FUNC)
X“Change to voice”

3