Nec PLASMASYNC PX-42VP3A, PLASMASYNC PX-42PD3 user Manual

PlasmaSync Plasma Monitor
User’s Manual
NEC Technologies
Important Information
Precautions
Please read this manual carefully before using your NEC plasma monitor and keep the manual handy for future reference.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALI­FIED SERVICE PERSONNEL.
This symbol warns the user that uninsulated volt­age within the unit may have sufficient magnitude to cause electric shock. Therefore, it is dangerous to make any kind of contact with any part inside of this unit.
This symbol alerts the user that important litera­ture concerning the operation and maintenance of this unit has been included. Therefore, it should
be read carefully in order to avoid any problems.
WARNING
TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EX­POSE THIS UNIT TO RAIN OR MOISTURE. ALSO DO NOT USE THIS UNIT'S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS, UNLESS THE PRONGS CAN BE FULLY INSERTED. REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH-VOLTAGE COMPONENTS INSIDE. REFER SERVICING TO QUALI­FIED SERVICE PERSONNEL.
DOC compliance Notice
This Class A digital apparatus meets all requirements of the Ca­nadian Interference-Causing Equipment Regulations.
The NEC plasma monitor is designed and manufactured to pro­vide long, trouble-free service. No maintenance other than clean­ing is required. Use a soft dry cloth to clean the panel. Never use solvents such as alcohol or thinner to clean the panel surface. The plasma display panel consists of fine picture elements (cells). Although NEC produces the plasma display panels with more than
99.99 percent active cells, there may be some cells that do not produce light or remain lit. For operating safety and to avoid damage to the unit, read care­fully and observe the following instructions. To avoid shock and fire hazards:
1. Provide adequate space for ventilation to avoid internal heat build-up. Do not cover rear vents or install in a closed cabinet or shelves. The unit is equipped with cooling fans. If you install the unit in an enclosure, be sure there is adequate space at the top of the unit to allow hot air to rise and escape. If the monitor becomes too hot, the overheat protector will be activated and the monitor will be turned off. If this happens, turn off the power to the monitor and unplug the power cord. If the room where the monitor is installed is particularly hot, move the monitor to a cooler location, and wait for the monitor to cool for 60 minutes. If the problem persists, contact your NEC dealer for service.
2. Do not use the power cord polarized plug with extension cords or outlets unless the prongs can be completely inserted.
3. Do not expose unit to water or moisture.
4. Avoid damage to the power cord, and do not attempt to modify the power cord.
5. Unplug unit during electrical storms or if unit will not be used over a long period.
6. Do not open the cabinet which has potentially dangerous high voltage components inside. If the unit is damaged in this way the warranty will be void. Moreover, there is a serious risk of electric shock.
7. Do not attempt to service or repair the unit. NEC is not liable for any bodily harm or damage caused if unqualified persons attempt service or open the back cover. Refer all service to authorized NEC Service Centers.
WARNING
This equipment has been tested and found to comply with the lim­its for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful in­terference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
2
PLASMA MONITOR
Important Information
NOTE:
When you connect a computer to this monitor, attach the sup­plied ferrite cores. If you do not do this, this monitor will not conform to mandatory FCC standards. Attaching the ferrite cores. Set the ferrite cores on both ends of the DVI cable (not sup­plied), and the power cable (supplied). Close the lid tightly until the clamps click.
DVI cable (not supplied)
band
core (small)
Power cable (supplied)
core (large)
band
(Plasma Monitor side)
Connector
core (small)
core (large)
Set side
To avoid damage and prolong operating life:
1. Use only with 120V 50/60Hz AC power supply. Continued op­eration at line voltages greater than 120 Volts AC will shorten the life of the unit, and might even cause a fire hazard.
2. Handle the unit carefully when installing it and do not drop.
3. Set the unit away from heat, excessive dust, and direct sun­light.
4. Protect the inside of the unit from liquids and small metal ob­jects. In case of accident, unplug the unit and have it serviced by an authorized NEC Service Center.
5. Do not hit or scratch the panel surface as this causes flaws on the surface of the screen.
6. For correct installation and mounting it is strongly recom­mended to use a trained, authorized NEC dealer.
7. As is the case with any phosphor-based display (like a CRT monitor, for example) light output will gradually decrease over the life of a Plasma Display Panel.
Recommendations to avoid or minimize phosphor burn-in
Like all phosphor-based display devices and all other gas plasma displays, Plasma monitors can be susceptible to phosphor burn under certain circumstances. Certain operating conditions, such as the continuous display of a static image over a prolonged pe­riod of time, can result in phosphor burn if proper precautions are not taken. To protect your investment in this NEC plasma moni­tor, please adhere to the following guidelines and recommenda­tions for minimizing the occurrence of image burn:
* Always enable and use your computer's screen saver function
during use with a computer input source. * Display a moving image whenever possible. * Always power down the monitor when you are finished using it.
NEC has built-in several operating modes in your PlasmaSync PD Series monitor to help you reduce the likelihood of phosphor burn. These are called the AccuShield Phosphor Protection System. If the Plasmasync monitor is in long-term use or continuous opera­tion, use the functions available in AccuShield to reduce the likeli­hood of perceptible phosphor burn or to diminish its perceptible effects if it occurs. See pages 37,45 and 46 for instructions on how to use the Orbiter, Low Brightness and Inverse RGB modes of AccuShield.
* Lower the Brightness and Contrast levels as much as possible
without impairing image readability. * Display an image with many colors and color gradations (ie.
photographic or photo-realistic images). * Create image content with minimal contrast between light and
dark areas. For example white characters on black backgrounds.
Use complementary or pastel colors whenever possible. * Avoid displaying images with few colors and distinct, sharply
defined borders between colors.
Contact NEC Technologies at 1-800-836-0655 for other recom­mended procedures that will best suit your particular application needs.
PLASMA MONITOR
3
Important Information
Précautions
Veuillez lire ce manuel avec attention avant d'utiliser votre PlasmaSync NEC moniteur et conserver ce manuel à portée de la main pour une consultation ultérieure.
ATTENTION
RISQUE D’ELECTROCUTION
NE PAS OUVRIR
MISE EN GARDE:AFIN DE REDUIRE LES RISQUES D’ELECTRO-CUTION, NE
PAS DEPOSER LE COUVERCLE, IL N’Y A AUCUNE PIECE UTI­LISABLE A L’INTERIEUR DE CET APPAREIL. NE CONFIER LES TRAVAUX D’ENTRETIEN QU’A UN PERSONNEL QUALIFIE.
Ce symbole a pour but de prévenir l’utilisateur de la présence d’une tension dangereuse, non isolée se trouvant à l’intérieur de l’appareil. Elle est d’une intensité suffisante pour constituer un risque d’électrocution. Eviter le contact avec les pièces à l’intérieur de cet appareil.
Ce symbole a pour but de prévenir l’utilisateur de la présence d’importantes instructions concernant l’entretien et le fonctionnement de cet appareil. Par conséquent, elles doivent être lues attentivement
afin d’éviter des problèmes.
AVERTISSEMENT
AFIN DE REDUIRE LES RISQUES D’INCENDIE OU D’ELECTROCUTION, NE PAS EXPOSER CET APPAREIL A LA PLUIE OU A L’HUMIDITE. AUSSI, NE PAS UTILISER LA FICHE POLARISEE AVEC UN PROLONGATEUR OU UNE AUTRE PRISE DE COURANT SAUF SI CES LAMES PEUVENT ETRE INSEREES A FOND. NE PAS OUVRIR LE COFFRET, DES COMPOSANTS HAUTE TENSION SE TROUVENT A L’INTERIEUR. LAISSER A UN PERSONNEL QUALIFIE LE SOIN DE REPARER CET APPAREIL.
DOC avis de conformation
Cet appareil numérigue de la classe A respecte toutes les exigences du Réglement sur le Matériel Brouilleur du Canada.
AVERTISSEMENT
Cet équipement a été testé et certifié conforme avec les limita­tions des équipements numériques de Classe A, conformément à l'article & (du règlement FCC. Ces limites sont conçues pour as­surer une protection raisonnable contre les interférences nuisibles lorsque l'équipement est utilisé en milieu commercial. Cet équipement génère, utilise, et peut produire de l'énergie de fréquence radio et, s'il n'est pas installé et utilisé selon le manuel d'instruction, peut provoquer des interférences nuisibles aux com­munications radio. L'utilisation de cet équipement dans une zone résidentielle est susceptible de provoquer des interférences nuisibles, dans quel cas l'utilisateur est tenu de remédier à ces interférences à ses frais.
Mises en garde et précautions de sécurité
Le moniteur PlasmaSync NEC a été conçu et fabriqué pour une utilisation fiable et durable. Il ne nécessite aucun entretien en de­hors du nettoyage. Utiliser un chiffon doux et sec pour nettoyer la surface de l'écran. Ne jamais utiliser de solvant comme l'alcool ou le diluant. Le panneau à affichage plasma est constitué de fines particules d'images ou pixels (cellules). Bien que NEC produise des panneaux à affichage plasma avec plus de 99,99 % de cel­lules actives, il peut y avoir des cellules qui ne produisent pas de lumière ou qui restent allumées. Pour des raisons de sécurité et pour éviter d'endommager l'appareil, lire attentivement les instructions suivantes. Pour éviter les risques d'éléctrocution et d'incendie:
1. Laisser suffisament d'espace autour de l'appareil pour la ven-
tilation et éviter toute augmentation excessive de la température interne. Ne pas couvrir les évents ou l'installer dans un endroit trop exigu. L'appareil est équipé de ventilateurs de refroidissement. Si vous installez l'appareil dans un espace clos, assurez-vous qu'il y ait suffisamment d'espace au dessus pour permettre à l'air chaud de s'élever et de s'évacuer. Si la température du moniteur devient excessive, la protection contre les surchauffes entrera en action et coupera l'alimentation. Dans ce cas, éteindre l'appareil et débrancher le câble d'alimentation. Si la température de la pièce dans laquelle le moniteur est installé est particulièrement excessive, déplacer l'appareil dans un endroit plus frais et le laisser refroidir 60 minutes. Si le problème persiste, prendre contact avec le revendeur NEC pour le service après-vente.
2. Ne pas utiliser la fiche polarisée du cordon d’alimentation avec
des prolongateurs ou des prises de courant, sauf si les lames peuvent être insérées à fond.
3. Ne pas exposer à L'eau ou à l’humidité.
4. Eviter d’endommager le cordon d’alimentation, et ne pas modi-
fier le cordon d’alimentation.
5. Débrancher l’appareil pendant les tempêtes ou si l’appareil n’est
pas utilisé pendant une longue période.
6. Ne pas ouvrir le coffret. Des composants de haute tension se
trouvent à l’intérieur. Si l’appareil est endommagé de cette manière, la garantie devient caduque. De plus, il y a risque d’électrocution.
7. Ne pas essayer de réparer ou entretenir l’appareil soi-même.
NEC ne saura être tenu pour responsable pour toute blessure ou dommage causé par des personnes non qualifiées qui essayent de réparer ou d’ouvrir le couvercle arrière. Confier toute réparation à un centre de service agréé NEC.
4
PLASMA MONITOR
Important Information
REMARQUE:
Lorsque vous branchez un micro-ordinateur sur ce moniteur, fixez les noyaux en ferrites fournis. Si vous ne le faîtes, le moniteur ne sera pas en conformité avec les exigences des standards FCC. Fixation des noyaux en ferrite. Installer les noyaux en ferrite à chaque extrémité du câble DVI (non fourni) et du câble dalimentation électrique (fourni). Fermez doucement le couvercle jusqu’à ce que les crans se clipsent. Utilisez le collier plastique pour fixer la tore en ferrite.
Câble DVI (non fourni)
Collier plastique
noyau (petit)
câble dalimentation électrique (fourni)
noyau (large)
Collier plastique
(côté du moniteur à plasma)
noyau (petit)
noyau (large)
Connecteur
côté de lappareil
Pour éviter des dommages et prolonger la durée de service de l’appareil:
1. N’utiliser qu’une source d’alimentation de 120 V 50/60 Hz CA. Le fait dutiliser lappareil en continu à des tensions de ligne supérieures à 120 Volts CA réduit sa durée de vie et risque de provoquer un incendie.
2. Manipuler l’appareil avec soin pendant son déplacement et ne pas le faire tomber.
3. Eloigner l’appareil des endroits chauds, très poussiéreux et exposés en plein soleil.
4. Eviter que des liquides et des petits objets métalliques pénètrent à l’intérieur de l’appareil. En cas d’accident, débrancher lappareil et le confier à un centre de service agréé NEC.
5. Ne pas frapper ou rayer la surface de la écran plasma, car des défauts risquent de se produire sur la surface de la écran plasma.
6. Pour effecteur une installation et un montage corrects, il est recommandé de faire appel au concessionnaire NEC autorisé et spécialisé.
7. Comme c'est le cas pour tout affichage à base de phosphore (comme un moniteur CRT, par exemple), la puissance de lumière baisse graduellement au cours de la vie du Panneau d'Affichage à Plasma.
Pour éviter le risque de combustion au phosphore, les mesures suivantes sont recommandées
Comme tous les appareils d'affichage à base de phosphore et tous les autres affichages à gaz plasma, les moniteurs Plasma peuvent être sujets à la combustion au phosphore dans certaines circonsatnces. Certaines conditions d'utilisation, telles que l'affichage continu d'une image statique pour une durée prolongée, peuvent causer des brûlures au phophore si aucune précaution n'est prise. Pour protéger votre investissement dans ce moniteur Plasma NEC, veuillez suivre les directives et les recommandations suivantes pour minimiser l'occurence de brûlure d'image :
* Assurez-vous de mettre en marche et d'utliser l'économisateur
d'écran chaque fois que c'est possible lorsque vous l'utilisez avec
une source d'entrée d'ordinateur. * Affichez une image en mouvement aussi souvent que possible. * Coupez toujours l'alimentation lorsque vous avez terminé
d'utiliser la moniteur.
NEC a installé de nombreux modes dopération dans votre moniteur de série PlasmaSync PD afin de minimiser les risques de com­bustion au phosphore. Ce système de protection a pour nom Système de Protection Phosphore AccuShield. Si le moniteur PlasmaSync est en usage pendant de longues périodes ou en utilisation continue, veuillez utiliser les fonctions disponibles dans le AccuShield pour minimiser les risques de combustion au phos­phore notable, ou pour en minimiser les conséquences si elle apparaît. Référez-vous aux pages 37,45 et 46 pour plus de détails sur lutilisation des modes Orbiter, Illumination Réduite et RVB In­verse de l’AccuShield.
* Abaissez le niveau de l'image (contraste, luminosité) autant que
possible, sans faire perdre la lisibilité de l'image. * Affichez une image avec de nombreuses couleurs et gradua-
tions de couleur (par ex. des images photographiques ou photo-
réalistes). *Créez un contenu d'image avec un contraste minimal entre les
zones sombres et les zones claires. Par exemple, des caractères
blancs sur un fond noir. Utilisez des couleurs complémentaires
ou pastels le plus souvent possible. * Évitez d'afficher des images avec peu de couleurs et des limites
nettes et clairement définies entre les couleurs.
Contactez NEC Technologies au 1-800-836-0655 pour d'autres procédures recommandées qui conviendront le mieux au besoin de votre appareil.
PLASMA MONITOR
5
Limited Warranty Plasma Monitors
NEC Technologies, Inc. (hereinafter NECTECH) warrants this prod­uct to be free from defects in material and workmanship under the following terms and, subject to the conditions set forth below, agrees to repair or replace (at NECTECH's sole option) any part of the enclosed unit which proves defective. Replacement parts or prod­ucts may be new or refurbished and will meet specifications of the original parts or products.
HOW LONG IS THE WARRANTY?
Parts and labor are warranted for (1) One Year from the date of the first customer purchase.
WHO IS PROTECTED?
This warranty may be enforced only by the first purchaser.
WHAT IS COVERED AND WHAT IS NOT COVERED
Except as specified below, this warranty covers all defects in ma­terial or workmanship in this product. The following are not cov­ered by the warranty:
1. Any product which is not distributed in the U.S.A. or Canada and Mexico by NECTECH or which is not purchased in the U.S.A. or Canada or Mexico from an authorized NECTECH dealer.
2. Any product on which the serial number has been defaced, modified or removed.
3. Damage, deterioration or malfunction resulting from: a. Accident, misuse, abuse, neglect, fire, water, lightning or
other acts of nature, unauthorized product modification, or failure to follow instructions supplied with the product.
b. Repair or attempted repair by anyone not authorized by
NECTECH.
c. Any shipment of the product (claims must be presented to
the carrier). d. Removal or installation of the product. e. Any other cause which does not relate to a product defect. f. Burns or residual images upon the phosphor of the panel.
4. Cartons, carrying cases, batteries, external cabinets, magnetic tapes, or any accessories used in connection with the product.
5. Service outside of the U.S.A. , Canada and Mexico.
LIMITATIONS OF LIABILITY
Except for the obligations specifically set forth in this warranty state­ment, we will not be liable for any direct, indirect, special, inciden­tal, consequential, or other types of damages, whether based on contract, tort, or any other legal theory, whether or not we have been advised of the possibility of such damages. This warranty is in lieu of all other warranties express or implied, including, but not limited to, the implied warranties of merchant­ability or fitness for a particular purpose.
EXCLUSION OF DAMAGES
NECTECH' s liability for any defective product is limited to the re­pair or replacement of the product at our option. NECTECH shall not be liable for:
1. Damage to other property caused by any defects in this prod­uct, damages based upon inconvenience, loss of use of the product, loss of time, commercial loss; or
2. Any other damages whether incidental, consequential or oth­erwise. Some states do not allow limitation on how long an implied warranty lasts and/or do not allow the exclusion or limi­tation of incidental or consequential damages, so the above limitations and exclusions may not apply to you.
HOW STATE LAW RELATES TO THE WARRANTY
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
FOR MORE INFORMATION, TELEPHONE 800-836-0655 NEC TECHNOLOGIES, INC. 1250 N. Arlington Heights Road, Suite 500 Itasca, Illinois 60143-1248
NOTE: All products returned to NECTECH for service MUST have prior ap­proval. To get approval, call NEC Technologies at 800-836-0655.
WHAT WE WILL PAY FOR AND WHAT WE WILL NOT PAY FOR
We will pay labor and material expenses for covered items, but we will not pay for the following:
1. Removal or installation charges.
2. Costs of initial technical adjustments (set-up), including ad­justment of user controls. These costs are the responsibility of the NECTECH dealer from whom the product was purchased.
3. Payment of shipping charges.
HOW YOU CAN GET WARRANTY SERVICE
1. To obtain service on your product, consult the dealer from whom you purchased the product.
2. Whenever warranty service is required, the original dated in­voice (or a copy) must be presented as proof of warranty cov­erage. Please also include in any mailing your name, address and a description of the problem(s).
3. For the name of the nearest NECTECH authorized service center, call NECTECH at 800-836-0655.
6
PLASMA MONITOR
Contents
Important Information ...................................................................................................................... 2
Limited Warranty Plasma Monitors ................................................................................................. 6
Contents ........................................................................................................................................... 7
How to Attach Options to the Plasma Monitor ................................................................................. 8
Introduction ...................................................................................................................................... 9
Part Names and Functions ............................................................................................................. 10
Control Panel ................................................................................................................................................. 10
Terminal Panel ................................................................................................................................................11
Remote Control ..............................................................................................................................................12
Operating Range for the Remote Control ....................................................................................................... 12
Setup Procedure ............................................................................................................................................13
Connections ................................................................................................................................... 14
Wiring Diagram ..............................................................................................................................................14
Connecting Your PC or IBM compatible ........................................................................................................15
Connecting Your Macintosh Computer .......................................................................................................... 16
Connections with Equipment that has a Digital Interface ...............................................................................17
Connecting Your VCR ....................................................................................................................................18
Connecting Your DVD Player.......................................................................................................................... 19
Connecting Your Stereo Amplifier ..................................................................................................................20
Basic Operation .............................................................................................................................. 21
Turning on the Main Power and Return to Standby Mode ............................................................................. 21
Turning On or Off the Power with the Remote Control ................................................................................... 21
Power Management Function ........................................................................................................................22
Selecting a computer or video source ............................................................................................................ 22
Menu Operations (On-screen Menu)............................................................................................... 23
Buttons Used in Menu Operations .................................................................................................................25
Operation of the Menu Screen .......................................................................................................................25
Configuration Menu (CONFIG MENU) ............................................................................................. 26
Audio Settings (SOUND) ................................................................................................................. 27
Picture Adjustments (VISUAL CONTROL) ....................................................................................... 28
Auto Picture/Wide Screen Settings (AUTO PICTURE)..................................................................... 29
Clock Frequency/Clock Phase Adjustment, and RGB Mode Adjustment (AUTO PICTURE) ..........................29
Wide Screen Setting (WIDE MODE) ............................................................................................................... 30
Horizontal/Vertical Position Adjustments (H-POSITION and V-POSITION) ...................................... 31
Direct Adjustment ........................................................................................................................................... 31
Menu Adjustments .........................................................................................................................................32
Input Selection (INPUT SELECT) .................................................................................................... 33
Standard Settings (NORMAL).......................................................................................................... 34
Information Screen (DISPLAY MODE) ............................................................................................. 35
Timer Settings (PRESENT TIME) .................................................................................................... 36
Time Settings .................................................................................................................................................36
Timer Settings ................................................................................................................................................36
4-Screen/9-Screen Multiple System Settings (VIDEO WALL MENU)............................................... 38
Menu Display Position Adjustment (OSM LOCATION) ..................................................................... 39
Other Functions (OTHER SETTINGS) .............................................................................................. 40
Color System Settings (COLOR SYSTEM) .....................................................................................................40
Power-On Mode Setting (P-ON MODE) .........................................................................................................40
Power Management Settings (POWER MANAGER) .......................................................................................41
ID Number Setting (SET ID NO) ..................................................................................................................... 43
RGB 3 Adjustment (RGB 3 ADJUST) .............................................................................................................43
Cinema Pulldown Setting (CINEMA PULLDOWN) .......................................................................................... 44
Standard/Cinema Image Settings (STD/CINEMA) .......................................................................................... 44
Long Life Settings (LONG LIFE MODE) ........................................................................................... 45
Long Life Settings (LONG LIFE MODE) ..........................................................................................................45
Gray Level Settings (GRAY LEVEL) ................................................................................................................46
Color Temperature Adjustment (COLOR TEMP) ............................................................................. 47
POWER/STANDBY Indicator ...................................................................................................................42
Appendix ........................................................................................................................................ 48
Opening the Terminal Cover ........................................................................................................................... 48
Mounting of the Remote Control Holder ........................................................................................................ 48
Placing the Remote Control into the Remote Control Holder .........................................................................49
Attaching the Ferrite Cores ............................................................................................................................ 50
Pin Configuration and Signal Level of Mini D-Sub 15-Pin (Analog) Input Connector ......................................51
Pin Configuration and Functions of External Control Connector (Mini D-Sub 9 -Pin) ..................................... 51
Command Reference List ........................................................................................................................53
Pin Configuration and Signal of the RGB 3 IN Connector (DVI Connector) ....................................................64
Signal Identification For Raster Preset............................................................................................................65
Specifications ................................................................................................................................................. 66
Troubleshooting.............................................................................................................................................. 67
Cabinet dimensions .......................................................................................................................................69
PLASMA MONITOR
7
How to Attach Options to the Plasma Monitor
You can attach your optional mounts or stand to the plasma moni­tor in one of the following two ways:
In the upright position.
Ventilation Requirements for enclosure mounting
To allow heat to disperse, leave space between surrounding ob­jects as shown in the diagram to the right.
50mm (1.97”)
Lay the screen face down.
31mm (1.22”)
31mm (1.22”)
50mm (1.97”)
45mm
(1.77”)
Lay the protective sheet, which was wrapped around the monitor when it was packaged, beneath the screen surface so as not to scratch the screen face.
This device cannot be used or installed without a separate Tabletop Stand or other optional mounting accessory. For proper installation it is strongly recommended to use a trained, NEC authorized service person. Failure to follow correct mounting procedures could result in damage to the equipment or injury to the user or installer. Product war­ranty does not cover damage caused by improper installa­tion. Failure to follow these recommendations could re­sult in voiding your warranty.
* Use only Listed Cart or Stand, or mounting kit or provided by
manufacturer.
8
PLASMA MONITOR
Introduction
OSM and IPM are trademarks of NEC Technologies, Inc. IBM PC/AT, PS/2, VGA, S-VGA, 8514/A and XGA are registered trademarks of International Business Machines Corporation. Apple and Macintosh are registered trademarks of Apple Com­puter, Inc. Microsoft is a registered trademark of Microsoft Corporation. Win­dows is a trademark of Microsoft Corporation.
Introduction to the PlasmaSync 42PD3
This section introduces you to your new PlasmaSync 42PD3, pro­vides a list of materials that comes with your monitor and describes the features and controls.
The features youll enjoy include:
* This unit can be used with IBM PC/AT, Macintosh, and com-
patibles.
(For details, see Factory Setting Values Preset Table. Pg.63) * Easy-to-operate remote control and external control connector. * Wired/Wireless Remote Control PX-RC2U (optional) can be used
as a wireless or as a wired remote control (with automatic switch-
ing by cable connection) and the remote THROUGH OUT con-
nector permits simultaneous operation of multiple monitors.
(A maximum of 3 units can be connected.)
The external control connector with a THROUGH OUT feature
permits various control functions to be made externally. * ID No. settings can be made for up to 256 units. * NTSC, PAL, SECAM, and M-NTSC composite video signals can
be accommodated
Video signals from video cameras, video decks, video disc play-
ers, and other video equipment adhering to NTSC as well as
PAL, SECAM, and M-NTSC (with a 4.43 MHz chroma signal)
standards can be selected on screen. * Varied set of input/output connectors
Video input/output: BNC video connector, S-video connector. Each type is equipped with its own THROUGH OUT connec­tor, single system.
Analog RGB input: mini D-Sub 15-pin connector, BNC (G, B, R, H/CS, V connectors). BNC is equipped with its own THROUGH OUT connector, single system.
DVD/HD input/output: BNC (Y, Cb/Pb, Cr/Pr connectors) BNC is equipped with its own THROUGH OUT connector, single system.
Audio input signals: Stereo RCAx2
Audio output signals: Stereo RCAx1
* Component video input terminal for DVD, 15.75 kHz (Y,Cb,Cr) * You can select RGB source or Component source for the 5BNC
terminal (RGB2/DVD/HD). When selecting an RGB input, the source is switched to the RGB input when selecting a compo-
nent input, the source is switched to the DVD/HD input. * Can be used with Digital RGB input (DVI standard compliant) * The signale plasma monitor provides four split screen feature. * Can be used with multiple screens : 4-screen and 9-screen
VIDEO WALL (For 9-screen, an optional distribution amplifier is
needed for VIDEO WALL ) * Power management function
RGB3 input mode complies with DMPM (Digital Monitor Power
Management) of DVI.
A great reduction in power consumption when not being used is
achieved through the VESA-proposed DPMS system.
The unit can also be used with the Energy Star standard (in
which case power consumption will be 15 W or less when not
being used). * The personal computer and the operating system that are to be
connected must be compatible with VESA DPMS.
Personal computers that are to be connected to the RGB3 input
must be compatible with DVI DMPM.
* OSM (On Screen Manager) function
The OSM function displays a variety of screen adjustment and correction menus on the screen to allow fine settings to be made.
* Plug and Play compatible
Plug and Play supports VESA DDC1 and DDC level B. (VESA DDC1 and DDC2 level B) The RGB3 input is compatible with DDC2 level B only.
* Can be used with RS-232C
* IBM PC/AT is a registered trademark of International Busi-
ness Machines Corporation. * Macintosh is a registered trademark of Apple Computer, Inc. * VESA is a trademark of Video Electronics Standard Associa-
tion. * DVI is an abbreviation for Digital Visual Interface.
Contents of the Package
The following lists all of the items included in your plasma monitor package. Please save the original box and packing materials for future transportation or shipment of this monitor.
1. Plasma monitor1
2. Power cable1
3. Wireless remote control1
4. AA battery2
5. Remote control holder1
6. RGB signal cable (mini D-sub 15-pin to mini D-sub 15-pin)1
7. Ferrite core (large)2
8. Ferrite core (small)2
9. User's manual1
10. Cord Clamper2
* These are fittings for fastening the unit to a wall to prevent tip-
ping due to external shock when using the stand (option). Fasten the safety fittings to the holes in the back of the monitor using the safety fitting mount screws.
Option
Wired/ Wireless Remote Control
Wall mount unit
Ceiling mount unit
Vertical wall mount unit
Tilt mount unit
Stand
Slant stand
Multi-screen mount unit
Multi-screen suport unit
Pole unit
Vertical pole mount unit
Horizontal pole mount unit
PLASMA MONITOR
9
Part Names and Functions
Control Panel
POWER/STANDBY
VIDEO EXITDOWNUPPROCEED
89
7
q POWER button ( )
Switches the main power on/off. See also page 21.
w EXIT button
Exits the on-screen menu (OSM) mode. See also page 25.
e PROCEED button
Sets the on-screen menu (OSM) mode and displays the on­screen menu. See also page 25.
r DOWN () button
Functions as the button in the on-screen menu (OSM) mode. See also page 25.
t UP ()button
Functions as the button in the on-screen menu (OSM) mode. See also page 25.
y RGB (+) button
Switches to the signal connected with the RGB input connec­tor. (Toggle switches between [RGB1], [RGB2] / [DVD/HD], or [RGB3].) Functions as the (+) button in the on-screen menu (OSM) mode. See also pages 22 and 25.
RGB
6
5
4
2
3
1
u VIDEO () button
Switches to the signal connected with the VIDEO input con­nector. Functions as the (–) button in the on-screen menu (OSM) mode. See also pages 22 and 25.
i Remote control sensor
Receives the signal from the remote control (when using the wireless remote control). See also page 12.
o POWER/STANDBY
The lamp color indicates the mode of power on/standby or power management. See also page 21.
* When the "CONTROL LOCK" toggle switch on the monitor's
input panel is set to "ON", the buttons on the set's front bezel control panel do not function.
10
PLASMA MONITOR
6 7
8 9
01
11
Terminal Panel
L
AUDIO
AUDIO
(
MONO
LR
)
IN 2
OUT
R
VIDEO
L (
AUDIO IN 1
MONO
)
RIN
IN
RGB 1
IN
RGB 2
/ DVD
/ HD
IN
RGB 3
OUT
S-VIDEO VIDEO
IN OUT
EXTERNAL CONTROL
OUT
G / Y B
/ C
B
/ P
B
/ C
R
/ P
R
H / CS VR
IN OUT
REMOTE
C / L
5
4
3 2
Part Names and Functions
1
AC IN
q AC IN connector
Connects with the supplied power cable.
w CONTROL LOCK
When "CONTROL LOCK" is set to "ON", the buttons on the set's front bezel control panel do not function.
e REMOTE (Mini jack)
IN jack: When you use the remote control with a wire, attach it
here. OUT jack: You can use this jack to output the remote control signal from the REMOTE IN jack.
* This is used when operating multiple monitors (this plasma moni-
tor) with a single remote control.
r EXTERNAL CONTROL (mini D-Sub 9 pin)
IN connector: Use when operating the plasma monitor from
the optional equipment with EXTERNAL CONTROL. OUT connector: You can use this connector to output the sig­nal from the EXTERNAL CONTROL IN connector.
t AUDIO OUT
You can use this jack to output the audio signal from the AU­DIO IN 1 or 2 jack.
y AUDIO IN 2
This is your audio input from your equipment such as a com­puter, VCR or DVD player.
u VIDEO
VIDEO IN connector (BNC): Here is where you connect a
composite video signal.
VIDEO OUT connector (BNC):
You can use this connector to output the composite video signal from the VIDEO IN connector. S-VIDEO IN connector (DIN 4 pin): Here is where you con­nect the S-video (Y/C separate signal).
S-VIDEO OUT connector (DIN 4 pin):
You can use this con-
nector to output the S-video signal from the S-VIDEO IN connector.
i AUDIO IN
This is your audio input from your equipment such as a com­puter, VCR or DVD player.
o RGB 1 IN (mini D-Sub 15 pin)
Connect the analog RGB signal of a personal computer or other RGB equipment.
!0 RGB 2/DVD/HD [G/Y, B/Cb/Pb, R/Cr/Pr, H/CS, V] (BNC)
IN connector: Connect the analog RGB signal or other RGB
equipment. The H/V composite signal is connected to the H/CS connec­tor. Also this connects with your equipment such as a DVD player and HDTV laser disk player. A Sync-on-Green signal can be connected to the G/Y connector OUT connector: You can use this connector to output the sig­nal from the RGB 2/DVD/HD IN connector.
!1 RGB 3 IN (DVI-I 29 pin)
Connects a digital RGB signal of a personal computer with a digital RGB output.
* This connector does not support analog input.
PLASMA MONITOR
11
Part Names and Functions
Remote Control
¡ POWER ON/OFF button
9
Switches the power on/off. See also page 21.
* If the POWER/STANDBY lamp is not
glowing, then these controls will not
§ POSITION/CONTROL buttons
Adjust the image location horizontally and ver­tically. See also pages 25 and 31. These buttons executes the menu selection and confirms adjustments/setting in the menu mode.
work.
PROCEED button
POWER OFF
RGB 1
2
EXI T
8
POSITION/CONTROL
POWER ON
RGB 2/DVD/HD
RGB 3
VI DEO
PROCEED
RGB 1 button
1
3
£ RGB 2 button
4
5
¢ RGB 3 button
7
Select the RGB1 input. See also page
22.
Select the RGB 2/DVD/HD input. See also page 22.
Select the RGB 3 input. See also page
22.
Displays the on-screen menu (Menu mode). See also page 25.
EXIT button
Exits the on-screen menu or Menu mode. See also page 25.
ª Infrared transmitter
Direct the remote control toward the remote sensor on the plasma monitor. See also page
12.
6
VIDEO button
Select the VIDEO input. See also page
22.
RP-102
NOTE:
* The wired/wireless remote control PX-RC2U is available as an option. * In addition to the features on the supplied remote control, the optional remote control has the following functions:
Direct remote button operation for picture adjustments such as contrast and brightness.
Direct remote button operation for picture and alignment adjustments such as horizontal and vertical position.
When the remote control is connected to the REMOTE IN jack with the remote cable, the optional remote control can be used as the wired remote control.
The REMOTE OUT connector is used to connect multiple plasma monitors together and allows all of the plasma monitors to be controlled by one remote control.
When you control multiple plasma monitors by the single remote control, you can assign an ID number to each plasma monitor so that all of the plasma monitors are not be affected at the same time.
Operating Range for the Remote Control
Point the top of the remote control toward the plasma monitor's remote sensor during button operation. Use the remote control within a distance of about 7 m/23 ft. from the front of the plasma monitor's remote control sensor and at a hori­zontal and vertical angle of within 30˚.
Approx. 7m/23ft
30˚ 30˚
POWER OFF
POWER ON
RGB 2/DVD/HD
RGB 1
RGB 3
VIDEO
EXIT
PROCEED
POSITION/CONTROL
RP-102
Important
The remote control system may not function when direct sunlight or strong illumination strikes the remote control sensor of the plasma monitor, or when there is an obstacle in the path. Should this happen, use the remote control in the wired operation.
Handling the remote control
* Do not subject to strong shock. * Do not allow water or other liquid to splash the remote con-
trol. If the remote control gets wet, wipe it dry immediately.
* Avoid exposure to heat and steam.
12
PLASMA MONITOR
Setup Procedure
1
Determine the installation location
Installation of only the plasma monitor is not possible. Be sure to use and install the plasma monitor in conjunction with a stand or special unit.
CAUTION
Installing your plasma display must be done by a qualified tech­nician. Contact your dealer for more information.
CAUTION
The retractable feet are for temporary use only and are not in­tended for permanent installation.
CAUTION
Failure to follow this caution may result in injury if the plasma monitor falls.
Important
Lay the protective sheet, which was wrapped around the plasma monitor when it was packaged, beneath the plasma monitor so as not to scratch the panel.
DO NOT ATTEMPT TO INSTALL THE PLASMA MONITOR.
DO NOT USE THE RETRACTABLE FEET FOR PURPOSE OF PERMANENT INSTAL­LATION.
MOVING OR INSTALLING THE PLASMA MONITOR MUST BE DONE BY TWO OR MORE PEOPLE.
4
Connect external equipment (See page 14)
To protect the connected equipment, turn off the main power before making connections.
Refer to your equipment user manual.
5
Connect the supplied power cable
The power outlet socket should be installed as near to the equip­ment as possible, and should be easily accessible.
Attach the supplied ferrite core to the power cable. See page
50.
Fully insert the prongs into the power outlet socket. Loose con­nection may cause noise.
6
Switch on the power of all the attached external equipment
When connected with a computer, switch on the power of the com­puter first.
7
Operate the attached external equipment.
2
Install the plasma monitor
In setting up a multiple screen system, please give consideration to the cable length and type since image quality may be degraded.
3
Install the remote control batteries
The remote control is powered by 1.5 V AA magnesium batteries. To install or replace batteries:
¡ Press and slide to open the cover.
Align the batteries according to
the (+) and (–) indications inside the case.
£ Replace the cover.
Display the signal on the external equipment you wish.
8
Select the input mode (See pages 22 and 27)
Select the appropriate input. When the equipment is connected to the RGB 2/DVD/HD, make the setting for the RGB 2 input. Make the VIDEO settings when a connection has been made to VIDEO. When an audio signal is connected, make the setting for sound.
9
Adjust the sound (See page 27)
Make adjustments when adjustment of the volume or balance is required.
10
Make adjustments when adjustment of the screen display position or distortion is required.
Adjust the screen (See pages 31 and 32)
11
Make adjustments when picture adjustment such as the bright­ness or contrast is required.
Adjust the image (See page 28)
PLASMA MONITOR
13
Connections
Before making connections:
* First turn off the power of all the attached equipment and make connections. * Refer to the user manual included with each equipment.
Wiring Diagram
Audio signal of input device
Personal computer
Personal computer
VCR
HD laser disk player
DVD player
Audio signal of input device
L
AUDIO
(
MONO
)
IN 2
R
VIDEO
L (
AUDIO IN 1
MONO
)
RIN
IN
RGB 1
IN
RGB 2
/ DVD
/ HD
IN
RGB 3
AUDIO
LR
OUT
OUT
S-VIDEO VIDEO
IN OUT
EXTERNAL CONTROL
OUT
G / Y B
/ C
B
/ P
B
/ C
R
/ P
R
H / CS VR
IN OUT
REMOTE
C / L
Plasma monitor
Amplifier
External control equipment
Wired remote control (optional)
Equipment with digital interface
Plasma monitor (second monitor)
Important
Four / Nine Multiple Screens System (VIDEO WALL MENU) * Multiple System requires the optional Multiple Unit. Contact your dealer for more information. * Use an optionally available BNC-typed signal cable that is within 1 to 2 m (3.3 to 6.6 feet) when one plasma monitor is connected to another one with the plasma monitor 's OUT and IN connectors. (Connection of up to 4 units is a rough standard.) If high image quality is especially desired, instead of using the OUT connectors of the plasma monitors, use a distributor (available separately) to divide the signals and connect them to the IN connectors of the various plasma monitors.
14
PLASMA MONITOR
Connections
Connecting Your PC or IBM compatible
Connecting your PC to your Plasma monitor will enable you to display your computer's screen image. Some video cards may not display an image correctly. If you wish to input wide signals, make the RGB MODE and INPUT MODE settings. (See "Signal Identification For Raster Preset" on page 64.)
Connect the Plasma Monitor to Your PC or IBM Compatible
To connect the RGB 1 IN connector (mini D-sub 15 pin) on the plasma monitor, use the supplied RGB signal cable (mini D-sub 15 pin to mini D-sub 15 pin).
To connect the RGB 2/DVD/HD IN connector (BNC) on the plasma monitor, use the optional signal cable (mini D-sub 15 pin to BNC x 5). Select [RGB] for RGB 2 from the INPUT SELECT menu. When connecting one or more Plasma monitors, use the RGB 2/DVD/HD OUT connector (BNC).
The AUDIO IN 1 and 2 can be both used for audio input. For connection, select [INPUT 1] or [INPUT 2] from the SOUND menu.
To analog RGB output
To audio right output
To audio left output
Mini D-sub 15 pin
L
AUDIO
AUDIO
(
MONO
LR
)
IN 2
OUT
R
OUT
S-VIDEO VIDEO
VIDEO
RCA
BNC x 5Mini D-sub 15 pin
L (
AUDIO IN 1
MONO
)
RIN
IN
RGB 1
IN
RGB 2
/ DVD
/ HD
IN
RGB 3
IN OUT
EXTERNAL CONTROL
OUT
G / Y B
/ C
B
/ P
B
/ C
R
/ P
R
H / CS VR
IN OUT
REMOTE
C / L
BNC x 5
Plasma monitor
BNC x 5
To RGB 2/DVD/HD IN
PC or IBM compatible
Plasma monitor (second monitor)
PLASMA MONITOR
15
Connections
Connecting Your Macintosh Computer
Connecting your Macintosh computer to your Plasma monitor will enable you to display your computer's screen image. Some video cards or drivers may not display images correctly. (See also "Signal Identification For Raster Preset" on page 64.)
Connect the Plasma Monitor to Your Macintosh
To connect the RGB 1 IN connector (mini D-sub 15 pin) on the plasma monitor, use the supplied RGB signal cable (mini D-sub 15 pin to mini D-sub 15 pin). For older Macintosh, use a pin adapter for Macintosh (available separately) to connect to your Macintosh's video port. The resolution modes that you can select are:
13" fixed mode 16" fixed mode 19" fixed mode
To connect the RGB 2/DVD/HD IN connector (BNC) on the plasma monitor, use the signal cable available separately (mini D-sub 15 pin
to BNC x 5). Select [RGB] for [RGB 2] from the INPUT SELECT menu. When connecting one or more Plasma monitors, use the RGB 2/DVD/HD OUT connector (BNC).
If you use with a Macintosh PowerBook, set "Mirroring" to Off. Refer to your Macintosh's owner's manual for more information about your computer's video output requirements and any special identification or configuring your monitor's image and monitor may require.
The AUDIO IN 1 and 2 (both RCA) can be both used for audio input. For connection, select [INPUT 1] or [INPUT 2] from the SOUND menu.
To video output port
To audio right output
To audio left output
Mini D-sub 15 pin
Mini D-sub 15 pin
Pin adapter for Macintosh
RCA
BNC x 5
L
AUDIO
(
MONO
)
IN 2
R
VIDEO
L (
AUDIO IN 1
MONO
)
RIN
IN
RGB 1
IN
RGB 2
/ DVD
/ HD
IN
RGB 3
AUDIO
LR
OUT
OUT
S-VIDEO VIDEO
IN OUT
EXTERNAL CONTROL
OUT
G / Y B
/ CB
/ PB H
/ CR
/ PR
/ CS VR
IN OUT
REMOTE
C / L
Plasma monitor
BNC x 5
BNC x 5
To RGB 2/DVD/HD IN
16
Macintosh
PLASMA MONITOR
Plasma monitor (second monitor)
Connections
Connections with Equipment that has a Digital Interface
Connections can be made with equipment that is equipped with a digital interface compliant with the DVI (Digital Visual Interface) standard. If you wish to input wide signals, perform the RGB MODE and INPUT MODE settings. (See Signal Identification For Raster Preset on page 64.)
Connect the Plasma Monitor to a Computer with a Digital Output
To connect the RGB 3 IN connector on the plasma monitor, use a DVI 29-pin signal cable (available separately).
The RGB 3 IN connector also accepts a DVI 25-pin (digital only) cable.
Input TMDS signals conforming to DVI standards.
To maintain display quality, use a cable with a quality prescribed by DVI standards that is within 2 meters (6.6 feet) in length.
Attach the supplied small ferrite cores to the DVI signal cable. See page 50 for attaching the ferrite cores.
The AUDIO IN 1 and 2 (both RCA) can be both used for audio input. For connection, select [INPUT 1] or [INPUT 2] from the SOUND
menu.
Equipment with a digital interface such as a personal computer with RGB output (TMDS)
To digital RGB output
DVI connector
Ferrite core
Ferrite core
To audio right output
To audio left output
RCA
RCA
DVI connector
L
AUDIO
(
MONO
)
IN 2
R
VIDEO
L (
AUDIO IN 1
MONO
)
RIN
IN
RGB 1
IN
RGB 2
/ DVD
/ HD
IN
RGB 3
AUDIO
LR
OUT
OUT
S-VIDEO VIDEO
IN OUT
EXTERNAL CONTROL
OUT
G / Y B
/ C
B
/ P
B
/ C
R
/ P
R
H / CS VR
IN OUT
REMOTE
C / L
Plasma monitor
PLASMA MONITOR
17
Connections
Connecting Your VCR
Connecting your VCR or laser disc player to your Plasma monitor will enable you to display your VCR' s or laser disc player' s video. Refer to your VCR or laser disc player owner's manual for more information.
Connect the Plasma Monitor to a VCR or Laser Disc Player
To connect the VIDEO IN connector (BNC) on the plasma monitor, use a separately available BNC connector cable. You will need a separately available BNC-to-RCA adapter to connect a VCR or laser disc player with an RCA pin jack to the BNC connector cable.
Video signals can be connected to either the VIDEO IN or the S-VIDEO IN connector. When making the connection, use the input selection menu to set (BNC) or (S-VIDEO).
Video output will be from the OUT connector that has been set here.
When connecting one or more Plasma monitors, use the VIDEO OUT connectors (BNC).
The AUDIO IN 1 and 2 (both RCA) can be both used for audio input. For connection, select [INPUT 1] or [INPUT 2] from the SOUND
menu.
DIN 4 pin
BNC-to-RCA adapter
To S-VIDEO OUT
BNC
To VIDEO OUT
DIN 4 pin
BNC
To audio right output
To audio left output
RCA
L
AUDIO
(
MONO
)
IN 2
R
VIDEO
L (
AUDIO IN 1
MONO
)
RIN
IN
RGB 1
IN
RGB 2
/ DVD
/ HD
IN
RGB 3
AUDIO
LR
OUT
OUT
S-VIDEO VIDEO
IN OUT
EXTERNAL CONTROL
OUT
G / Y B
/ CB
/ PB H
/ CR
/ PR
/ CS VR
IN OUT
REMOTE
C / L
DIN 4 pin
BNC
Plasma monitor
BNC
DIN 4 pin
To VIDEO IN To S-VIDEO IN
18
VCR or Laser disc player
PLASMA MONITOR
Plasma monitor (second monitor)
Connections
Connecting Your DVD Player
Connecting your DVD player to your Plasma monitor will enable you to display your DVD' s video. Refer to your DVD player owner's manual for more information. * When [CINEMA PULLDOWN] is set to [ON] with another function menu and the film recording software that has filmed the video in 24
frames per second (progressive) is played back, the plasma monitor fetches...3 frames, 2 frames and converts them into a 60 frames per second progressive signal. (2-3 pulldown) Note that this is valid only for NTSC, PAL, and 480I (60 Hz) signals.
Connect the Plasma Monitor to a DVD Player
To connect the RGB 2/DVD/HD IN connector (BNC) on the plasma monitor, use a separately available BNC connector cable. You will need a separately available BNC-to-RCA adapter to connect a DVD player with an RCA pin jack to the BNC connector cable. Some DVD players may have different connectors such as Y,Cb/Pb, and Cr/Pr. Select [DVD/HD] for RGB 2 from the INPUT SELECT menu. When connecting one or more Plasma monitors, use the RGB 2/DVD/HD OUT connectors (BNC).
The AUDIO IN 1 and 2 (both RCA) can be both used for audio input. For connection, select [INPUT 1] or [INPUT 2] from the SOUND menu.
To audio right output
To audio left output
To DVD Component video output
BNC X3
BNC-to-RCA adapter
RCA
BNC X3
L
AUDIO
(
MONO
)
IN 2
R
VIDEO
L (
AUDIO IN 1
MONO
)
RIN
IN
RGB 1
IN
RGB 2
/ DVD
/ HD
IN
RGB 3
AUDIO
LR
OUT
OUT
S-VIDEO VIDEO
IN OUT
EXTERNAL CONTROL
OUT
G / Y B
/ C
B
/ P
B
/ C
R
/ P
R
H / CS VR
IN OUT
REMOTE
C / L
Plasma monitor
BNC X3
BNC X3
To RGB 2/DVD/HD IN
DVD player
Plasma monitor (second monitor)
PLASMA MONITOR
19
Connections
Connecting Your Stereo Amplifier
You can connect your stereo amplifier to your Plasma monitor. Refer to your amplifier owner's manual for more information.
Connect the Plasma Monitor to a Stereo Amplifier
Turn on the plasma monitor and the amplifier only after all hookups have been made.
Use an RCA cable to connect the AUDIO OUT connector (RCA) on the plasma monitor and the audio input on the amplifier.
Do not reverse the audio left and right jacks.
The AUDIO IN 1 and 2 (both RCA) can be both used for audio input. For connection, select [INPUT 1] or [INPUT 2] from the SOUND
menu.
The AUDIO OUT jack outputs sound for the currently selected video.
RCA
To audio right output
To audio left output
RCA
L
AUDIO
(
MONO
)
IN 2
R
VIDEO
L (
AUDIO IN 1
MONO
)
RIN
IN
RGB 1
IN
RGB 2
/ DVD
/ HD
IN
RGB 3
AUDIO
LR
OUT
OUT
S-VIDEO VIDEO
IN OUT
EXTERNAL CONTROL
OUT
G / Y B
/ CB
/ PB H
/ CR
/ PR
/ CS VR
IN OUT
REMOTE
C / L
RCA
Plasma monitor
RCA
To audio right input
To audio left input
Amplifier
20
VCR or Laser disc player
PLASMA MONITOR
External speaker
External speaker
Basic Operation
POWER/STANDBY
POWER/STANDBY
POWER/STANDBY
POWER/STANDBY
Before operating the remote control, be sure to turn on the main power to the plasma monitor.
Turning on the Main Power and Return to Standby Mode
The plasma monitor enters the standby mode and the POWER/ STANDBY light is lit in orange when the power cable is plugged into the wall outlet.
To turn the main power:
Press the POWER button on the front panel of the plasma monitor
The main power will be turned on. The POWER/STANDBY light turns lit in green.
To turn off the power
(standby mode):
Press the POWER button again
The plasma monitor is in standby mode. The POWER/STANDBY light turns lit in orange.
POWER OFF
RGB 2/DVD/HD
RGB 1
VI DEO
EXI T
POSITION/CONTROL
RP-102
POWER ON
RGB 3
PROCEED
Turning On or Off the Power with the Remote Control
To turn on the plasma monitor:
Make sure that the POWER/STANDBY light turns lit in orange (standby).
Press the POWER ON button on the re­mote control.
The plasma monitor is turned on. The POWER/STANDBY light turns lit in green.
To turn off the plasma monitor:
Press the POWER OFF button on the remote control.
The plasma monitor enters the standby mode. The POWER/STANDBY light turns lit in orange.
* The standby mode used here is the condition that exists when
the power management is on. This is not the standby mode set by the remote control's powering-off.
PLASMA MONITOR
21
Basic Operation
POWER/STANDBY Light Status
Status POWER/STANDBY light
Normal
Error
NOTE: In some cases the fan may stop running. This is not a malfunction.
Main Power ON Timer enabled Power OFF with remote control Main Power Standby Abnormal heat warning Cracked panel glass
Green Orange flashing Orange Orange Green flashing Green and/or Orange flashing
Selecting a computer or video source
To view a video source:
Use the input selection menu to set [VIDEO] to [BNC] or [S-VIDEO].
Press the VIDEO button.
Displays the image from the equipment connected to the VIDEO IN connector.
See page 21 for connection.
To view the image from a computer, DVD player or HD laser disc player:
Important
Notes on the POWER/STANDBY light on the plasma monitor
* When the indicator light flashes at a time other than during timer setting,
it indicates a fault of the monitor. Should this happen, immediately switch off the main power of the moni­tor, disconnect the power plug from the outlet, and request repair ser­vice from your dealer.
Select [RGB] or [DVD/HD] for RGB 2 from the INPUT SELECT menu.
Press the source button (RGB 1, RGB 2/DVD/HD, or RGB 3)
Displays the image from the computer, DVD player or HD laser disc player connected to the selected RGB input connector.
You can select the source also by using the RGB button on the front panel. To do this, each press of the RGB button selects [RGB 1] [RGB 2] or [DVD/HD] [RGB 3] in sequence.
See page 14 for connection.
When Using Power Management Function
NOTE:
This plasma monitor follows the VESA approved DPMS Power Management function. The power management function is an energy saving function that automatically reduces the power consumption of the display when the keyboard or the mouse has not been used for a fixed period. The status of power management can be checked by POWER/ STANDBY light display. See page 42.
* The default input is the last input used, but the plasma monitor can be
configured to display either the last input used or a preset input when­ever it is used turned on. (See "Power-On Mode Setting" on page 40.)
* During RGB3 mode the power management function is available in Off-
state only. (This is Active-off Power state in DMPM of DVI standard.) An image will be displayed in 4 seconds after TMDS signal is returned.
22
PLASMA MONITOR
Menu Operations (On-screen Menu)
Use of the on-screen menu (OSM) function allows the setting of a variety of detailed adjustments. The adjustment settings are retained even when the power is switched off. The on-screen menu (OSM) function displays a menu on the screen from which the adjustments are made.
List of Setting Details
Icon Configuration menu
CONFIG MENU (Configuration menu) To display this menu, press and hold the button and
(None)
the PROCEED button at the same time for 3 seconds or longer on the main unit.
Sub menu
OSD DISPLAY OSD MODE
WIRELESS REMOTE CONTROL SYNC MODE PLE LINK
ALL RESET
Sets whether or not the main menu is displayed. Sets whether or not the second screen of the main menu is displayed. Sets whether or not wireless transmission of the remote control is enabled. Sets the sync signals that will be automatically selected. Sets the brightness of the screen when there are multiple screens. Returns all adjustments and settings of CONFIG MENU to the factory default values.
Main Menu Page 1 Items (OSD MODE : BASIC and PRO)
Icon Main menu
SOUND (Audio settings)
VISUAL CONTROL (Picture adjustments)
Sub menu
VOLUME BALANCE MUTE INPUT1 INPUT2
BRIGHTNESS CONTRAST SHARPNESS COLOR TINT
Volume adjustment Left-right balance adjustment Mute setting Sets audio input to AUDIO IN 1 Sets audio input to AUDIO IN 2
Screen brightness adjustment Image contrast adjustment Image sharpness adjustment Adjustment of color saturation Tint adjustment
Adjustment settings
Adjustment settings
Page
26 26
26
26 26
26
Page
27 27 27 27 27
28 28 28 28 28
AUTO PICTURE (Auto picture/Wide screen settings)
H-POSITION (Horizontal position adjustment)
V-POSITION (Vertical position adjustment)
INPUT SELECT (Input selection)
NORMAL (Standard settings)
(To Page 2)
AUTO PICTURE INPUT MODE
RGB MODE
WIDE MODE PICTURE ADJ FINE PICTURE
H-POSITION H-WIDTH
V-POSITION V-HEIGHT
RGB2 SCART
VIDEO ALL RASTER NORMAL
ALL VISUAL NORMAL
ALL NORMAL
Sets the automatic adjustment of the clock frequency/clock phase. This is set when switching of input signal discrimination is required. Sets the mode (moving picture/still picture mode) to suit the input signal. WIDE MODE setting Adjusts the clock frequency. Adjusts the clock phase.
Horizontal position adjustment of the screen Screen width adjustment
Vertical position adjustment of the screen Screen height adjustment
RGB signal or DVD/HD signal setting Sets whether or not the SCART jack is connected. (not used in the United States.) Sets the connector that is assigned to video input.
Returns the horizontal/vertical position and other adjust­ments of the screen to the default settings. Returns the audio settings, picture, and color temperature adjustments to the default settings. Returns all adjustments and setting to default values.
Setting [OSD MODE] to [PRO] on the configuration menu displays the second page of the main menu.
29 29
29
30 29 29
32 32
32 32
33 33
33 34
34
34
PLASMA MONITOR
23
Menu Operations
Main Menu Page 2 Items (OSD MODE : PRO)
Icon Main menu
(To Page 1)
DISPLAY MODE (Information screen)
PRESENT TIME (Timer setting)
VIDEO WALL MENU (4-Screen/9-Screen Multiple System Settings)
OSM LOCATION (Menu display position adjustments)
OTHER SETTING (Other settings)
LONG LIFE MODE (Long Life settings)
COLOR TEMP (Color temperature adjust­ment)
(To Page 1)
Sub menu
Setting [OSD MODE] to [PRO] on the configuration menu displays the first page of the main menu.
SOURCE INFO. Allows verification of the currently input signal (data). 35
DATE TIME TIMER
SCREEN DIVIDER POSITION DISP MODE
OSM H-POS OSM V-POS OSM ANGLE OSM DISPLAY TIME
COLOR SYSTEM
P-ON MODE
POWER MANAGER SET ID NO RGB3 ADJUST CINEMA PULLDOWN STD/CINEMA ALL RESET
LUM LIMIT ORBITTING
INV/WT
PROG. ORBIT GRAY LEVEL
ALL RESET
HIGH
LOW
USER1-4
Sets the date. Sets the time. Sets the "On/Off" time for switching the power and sets the input mode.
Sets the number of screens to be used to 1, 4, or 9 screens. Sets the screen position. Sets the display mode.
Menu display horizontal position adjustment Menu display vertical position adjustment Sets the menu display as a horizontal or vertical screen. Sets the menu display time.
Sets the color system (to AUTO, 3.58 NTSC, PAL, SECAM, or 4.43 NTSC). Sets the input mode that will be in effect when power is switched on. Sets the power management function. Sets ID numbers for up to 256 units. Set when the RGB 3 image is not stable. Sets the cinema pulldown. Makes the settings for the standard image and the cinema image. Returns the settings of all other functions to the default values.
Limits screen brightness to reduce image burn-in. Moves the screen at fixed intervals to reduce image burn­in. Displays an inverse (negative/positive) screen or an all­white image to reduce image burn-in. Programs the movement of screen dots to reduce burn-in. Adjusts the brightness of screen portions other than im­ages appearing at the upper, lower, or left, right areas of the screen in NORMAL or other modes. Returns all long life settings to the default values.
Sets the color temperature high. Produces a white with a strong blue content. Sets the color temperature low. Produces a white with a strong red content. Adjusts white balance.
Setting [OSD MODE] to [PRO] on the configuration menu displays the first page of the main menu.
Adjustment settings
Page
36 36 36
38 38 38
39 39 39 39
40
40
41 43 43 44 44 43
45 45
45
45 46
45 47
47
47
24
PLASMA MONITOR
POWER OFF
RGB 2/DVD/HD
RGB 1
VI DEO
EXI T
POSITION/CONTROL
RP-102
POWER ON
RGB 3
PROCEED
Menu Operations
Buttons Used in Menu Operations
Perform operations with the remote control and main unit operation buttons.
PROCEED button
Displays the main menu. Determine the selection or set details in the main menu and proceed to the next step.
EXIT button
Turns off the main menu. Press during display of the sub menu to return to the main menu.
NOTE: CONFIG MENU
Among the various on-screen menus (OSM), only the CONFIG MENU is displayed by pressing and holding the main unit POSITION/CONTROL ▲ button and the PROCEED button simultaneously for 3 seconds or longer. The menu screen of the CONFIG MENU does not contain icons that indicate menu items; however, operation is the same as with other screens.
POSITION/CONTROL buttons
button: Moves the cursor up.button: Moves the cursor down.
button: Moves the cursor left.
Press during display of the sub menu (set­ting/adjustment screen) to select setting items
button: Moves the cursor right.
and also to decrease the adjustment value.
Press during display of the sub menu (set­ting/adjustment screen) to select setting items and also to increase the adjustment value.
Operation of the Menu Screen
Main menu Sub menu
The main menu comprises 2 pages (screens). Place the cursor on
icon
or  and use the POSITION/CONTROL / button to change the page. (Set [OSD MODE] to [PRO] on the configuration menu before performing other operations.)
Items of the main menu are displayed as icons. See Pages 23 and 24 for details.
VOLUME BALANCE MUTE INPUT1 INPUT2
SOURCE INFO. RGB1 H-FREQ. V-FREQ. H-POL. V-POL.
: OFF : VIDEO : RGB1
31.5kHz
60.0Hz NEG POS
Displays the next page.
Place the cursor here
and press the  button to display the next page.
Items of the main menu are displayed as icons. See Pages 23 and 24 for details.
Displays the previous page.
BRIGHTNESS
Cursor
CONTRAST SHARPNESS COLOR TINT
Indication of the adjustment value.
NOTE: Auto Memory
The setting value is automatically stored after the adjustment. Note that setting values will not be automatically stored in the following circumstances.
* The power cable is disconnected from the outlet during the setting. * There is a power outage during the setting.
PLASMA MONITOR
25
Configuration Menu (CONFIG MENU)
This menu sets the main menu, display of adjustment details, remote control, sync, and the brightness of the multiple system.
Preparation Simultaneously press and hold the POSITION/CONTROL button and the PROCEED button for 3 seconds or longer
to display the menu screen.
Align the cursor with the desired item
1
Move the cursor up and down with the POSITION/CONTROL ▲▼ buttons.
Adjust with the POSITION/CONTROL
2
 
buttons
Press the EXIT button 2 times
CONFIG MENU
OSD DISPLAY :NORMAL OSD MODE :BASIC WIRELESS REMOTE CONTROL :ON SYNC MODE :AUTO PLE LINK :OFF ALL RESET
CONFIG MENU
OSD DISPLAY :KEY OSD MODE :BASIC WIRELESS REMOTE CONTROL :ON SYNC MODE :AUTO PLE LINK :OFF ALL RESET
3
Press the EXIT button one time to return to the config menu. One further press removes the menu.
Adjustment Items
OSD DISPLAY [NORMAL] : [KEY] :
[OFF] :
OSD MODE [BASIC] : [PRO] :
WIRELESS REMOTE CONTROL [ON] : Enables remote control wireless transmission. [OFF] : Disables remote control wireless transmission.
* This is normally left [ON]. Set [OFF] to avoid unwanted
control from other remote controls.
SYNC MODE [AUTO] : Automatically detects separate sync signals,
[GSYNC] : Automatically detects green sync signal (i.e.,
[CSYNC] : Automatically detects composite sync signal.
PLE LINK [ON] : Sets a uniform screen brightness for each
[OFF] : Sets the screen brightness for each of the
Displays the menu screen and adjustment details. Displays the adjustment details for only input switch­ing and direct adjustments. No display of any menu screens or adjustment details.
Allows only the first page of the main menu to be displayed. Allows Pages 1 and 2 of the main menu to be displayed.
green sync signal (i.e., sync-on-green), and composite sync signal.
sync-on-green).
screen in a 4-screen multiple system.
screens in a 4-screen or multiple system to their respective brightness.
26
PLASMA MONITOR
* Set [OFF] in a 9-screen multiple system. * When this function is set [ON], connect four plasma moni-
tors with the remote control cable (included with the op­tional remote control) in the order of the position numbers for 4-screen multiple system. See the drawing below.
REMOTE
REMOTE
REMOTE
OUT
No.2 No.3No.4
No.2 No.3No.4
OUT
REMOTE
REMOTE
REMOTE IN
No.1
IN
Monitor Monitor
No.1
Monitor Monitor
OUT
No.1
No.2
REMOTE OUT
No.3No.4
IN
No.1
No.2
REMOTE
No.3No.4
IN
Note:
Please use the control panel of the main unit at this time since operation with the remote control will not be enabled with this arrangement.
ALL RESET Align the cursor and then press the PROCEED button to return all adjustments and settings of CONFIG MENU to the factory default values.
Audio Settings (SOUND)
This menu sets the volume, balance, mute, and selection of input. Note that only sound of the currently displayed signal is output.
Preparation Press the PROCEED button to display the main menu.
Align the cursor with
1
Move the cursor left and right with the POSITION/CONTROL buttons.
Align the cursor with the desired item
 
VOLUME BALANCE MUTE INPUT1 INPUT2
2
Move the cursor up and down with the POSITION/CONTROL ▲▼ buttons.
Adjust with the POSITION/CONTROL
3
 
buttons
VOLUME BALANCE MUTE INPUT1 INPUT2
: OFF : VIDEO : RGB1
: OFF : VIDEO : RGB1
Adjustment Screen
[VOLUME] : Adjusts the volume
Decrease Increase
[BALANCE]: Adjusts the left and right volume balance.
L
Left side becomes stronger Right side becomes stronger
L
R
[MUTE] : Switches off the sound (temporarily)
[OFF] : There is sound. [ON] : Sound is switched off.
[INPUT 1] : Each press serves to advance the audio input
of AUDIO IN 1 by one step.
RGB 3
RGB 2
or
VIDEO
RGB 1
[INPUT 2] : Each press serves to advance the audio input
of AUDIO IN 2 by one step.
RGB 1
RGB 2
or
VIDEO
DVD/HD
DVD/HD
RGB 3
R
VOLUME BALANCE MUTE INPUT1 INPUT2
: OFF : VIDEO : RGB1
Press the EXIT button 2 times
4
Press the EXIT button one time to return to the main menu. One further press removes the menu.
Note:
Adjustments of [VOLUME], [BALANCE], [MUTE] will be stored in memory for each input (VIDEO, RGB 1-3, DVD/HD, and SCART). To change these settings, first display the source of which audio input you wish to adjust.
PLASMA MONITOR
27
Picture Adjustments (VISUAL CONTROL)
This menu adjusts the brightness, contrast, sharpness, color, and tint.
Preparation Press the PROCEED button to display the main menu.
Align the cursor with
1
Move the cursor left and right with the POSITION/CONTROL buttons.
Align the cursor with the desired item
 
BRIGHTNESS CONTRAST SHARPNESS COLOR TINT
2
Move the cursor up and down with the POSITION/CONTROL ▲▼ buttons.
Adjust with the POSITION/CONTROL
3
 
buttons
BRIGHTNESS CONTRAST SHARPNESS COLOR TINT
Adjustment Screen
[BRIGHTNESS]
[CONTRAST]
[SHARPNESS]
[COLOR] : Adjusts the color saturation
[TINT] : Adjusts the tint.
: Adjusts the brightness of the screen.
Darker Brighter
: Adjusts the contrast of the image.
Fainter Denser
: Adjusts the sharpness of the image.
Softer More distinct
Less saturated More saturated
Tinted toward red Tinted toward green
* These adjustments will not be available when
the color system setting is set to [PAL] or [SECAM].
BRIGHTNESS CONTRAST SHARPNESS COLOR TINT
Press the EXIT button 2 times
4
Press the EXIT button one time to return to the main menu. One further press removes the menu.
Note:
Only the [BRIGHTNESS] and [CONTRAST] adjustments are available with the RGB input screen.
28
PLASMA MONITOR
Auto Picture/Wide Screen Settings (AUTO PICTURE)
Clock Frequency/Clock Phase Adjustment, and RGB Mode Adjustment (AUTO PICTURE)
There is normally no need to adjust the clock frequency or clock phase when [AUTO PICTURE] is set to [ON]; however, when automatic adjustment cannot adjust the picture properly, a manual adjustment should be made. Make an adjustment when a signal is newly input, and when vertical lines appear and the image appears blurred.
Preparation Press the PROCEED button to display the main menu.
Align the cursor with
1
Move the cursor left and right with the POSITION/CONTROL buttons.
 
Align the cursor with AUTO PICTURE
AUTO PICTURE INPUT MODE RGB MODE
WIDE MODE : FULL
2
Move the cursor up and down with the POSITION/CONTROL ▲▼ buttons.
Select OFF with the POSITION/CONTROL
3
 
buttons
AUTO PICTURE INPUT MODE RGB MODE
WIDE MODE : FULL
AUTO PICTURE INPUT MODE RGB MODE PICTURE ADJ FINE PICTURE WIDE MODE : FULL
: ON : 4X3 : STILL
: ON : 4X3 : STILL
: OFF : 4X3 : STILL
Adjust with the POSITION/CONTROL
5
buttons
[RGB MODE] : Sets the mode (i.e., moving picture/still
picture mode) to suit the input signal [PICTURE ADJ] : Adjusts the clock frequency [FINE PICTURE] : Adjusts the clock phase
 
Press the EXIT button 2 times
6
Press the EXIT button one time to return to the main menu. One further press removes the menu.
Note:
AUTO PICTURE
Adjustment of [H-POSITION] and [V-POSITION] is not available when [AUTO PICTURE] is set to [ON] at the time of RGB signal input. When adjustment is required, set [AUTO PICTURE] to [OFF]. When the displayed image is small with respect to the original number of horizontal pixels (including instances where the display area, i.e., lit pix­els is small), the picture may take up to 6 seconds to be displayed.
RGB MODE
[MOTION] : Set when a moving picture source is connected such as a
scan converter. [STILL] : Set when displaying a personal computer screen. [DTV] : Set when viewing a source such as a digital broadcast using
RGB input.
Clock Frequency Adjustment (PICTURE ADJ)
This adjusts the width of the image with respect to the screen. Adjustment is performed with a dot unit signal. Adjust to the position at which vertical flickering disappears.
Align the cursor with the desired item
4
Move the cursor up and down with the POSITION/CONTROL ▲▼ buttons.
INPUT MODE:
[4x3], [16x9] and [16x9!] are used in the discrimination and switching of the input signal. See "INPUT MODE" of "Signal Identification For Raster Preset" (P.64) when making the setting.
AUTO PICTURE INPUT MODE RGB MODE PICTURE ADJ FINE PICTURE WIDE MODE : FULL
: OFF : 4X3 : STILL
When the width of the image signal is wider than the monitor screen, adjust the size with the POSITION/ CONTROL  button. When the width of the image signal is narrower than the monitor screen, adjust the size with the POSITION/ CONTROL  button.
: Monitor screen size
Clock Phase Adjustment (FINE PICTURE)
Adjust for minimal screen noise, flicker, and color infidelity. First adjust the clock frequency, then perform the clock phase adjust­ment. * Clock frequency and clock phase adjustments are not available at the
time of VIDEO (and S-VIDEO) input.
PLASMA MONITOR
: Image signal size
29
Auto Picture/Wide Screen Settings (AUTO PICTURE)
Wide Screen Setting (WIDE MODE)
This sets the wide screen display (to NORMAL, FULL, ZOOM, or STADIUM).
Preparation Press the PROCEED button to display the main menu.
Align the cursor with
1
Move the cursor left and right with the POSITION/CONTROL buttons.
Align the cursor with AUTO PICTURE
 
AUTO PICTURE INPUT MODE RGB MODE
WIDE MODE : FULL
: OFF : 4X3 : STILL
2
Move the cursor up and down with the POSITION/CONTROL ▲▼ buttons.
AUTO PICTURE INPUT MODE RGB MODE
WIDE MODE : FULL
Set the wide screen mode with the
3
POSITION/CONTROL
[NORMAL] : This is the normal screen size (4:3). [FULL] : Enlarges the picture left and right. [ZOOM] : Enlarges the picture left to right and top to bot-
tom in the same proportion.
[STADIUM] : Enlarges each of the left to right and top to bot-
tom values in their respective ratios.
 
buttons
: OFF : 4X3 : STILL
Important
Precautions in Normal Mode
There are marked differences in brightness between the display portions and non-display portions (where there is no image) in [NORMAL] mode which result in image burn-in due to the strong contrast. In view of this, the following settings are strongly recommended. Note that image burn-in will still occur, though somewhat later, even after making these settings and that burn-in cannot be suppressed. The moni­tor should be used in [FULL] mode as much as possible.
1. Perform gray level settings to narrow the differences in brightness be-
tween display and non-display portions of the image. (See P.46)
2. Weaken the image adjustment contrast and brightness. (See P.28)
3. Perform the Long Life settings. (P.45)
Copyright
Please note that using this monitor for the purpose of commercial gain or the attraction of public attention in a venue such as a coffee shop or hotel and employing compression or expansion of the screen image with a wide screen setting (of FULL, ZOOM, or STADIUM) raises concern about the infringement of copyright rights which are protected by copyright law.
Screen Size and the Original Image
This monitor is equipped with a wide variety of wide screen settings. Se­lection of a screen size that differs with the image aspect ratio (i.e., the ratio of the vertical and horizontal dimensions of the screen) of the video tape or other software will produce differences in appearance with re­spect to the original image. Please keep this point in mind when selecting the screen size.
* Only [NORMAL] and [FULL] settings are available with an
RGB input screen.
Press the EXIT button 2 times
4
Press the EXIT button one time to return to the main menu. One further press removes the menu.
30
PLASMA MONITOR
Note:
Supported Input Signals and Resolutions
Please see Page 64 for information about the input signals and resolu­tions that this monitor supports.
Horizontal/Vertical Position Adjustments (H-POSITION and V-POSITION)
Horizontal and vertical position adjustments are available in 2 ways. Direct adjustment makes adjustments simply by pressing the buttons of the remote control and Menu control adjustments are made via menu display.
Direct Adjustment
Adjusts the horizontal position and the vertical position of the screen. A press of the button displays the adjustment screen. Release your finger from the button after the adjustment is made. The dis­play will disappear about 3 seconds later and the adjustment de­tails will be stored.
 
Horizontal position adjustment (POSITION/CONTROL
)
POWER OFF
POWER ON
RGB 2/DVD/HD
H-POSITION
Move left Move right
Vertical position adjustment (POSITION/CONTROL
▲▼
)
V-POSITION
▼ Move down Move up ▲
RGB 1
VI DEO
EXI T
POSITION/CONTROL
RP-102
RGB 3
PROCEED
PLASMA MONITOR
31
Horizontal/Vertical Position Adjustments (H-POSITION and V-POSITION)
Menu Adjustments
Horizontal position adjustment
Adjusts the horizontal position and width of the screen.
Preparation Press the PROCEED button to display the main
menu.
Align the cursor with
1
Move the cursor left and right with the POSITION/CONTROL buttons.
H-WIDTH is adjustable only in multiple mode.
Align the cursor with the desired item
 
V-POSITION V-HEIGHT
2
Move the cursor up and down with the POSITION/CONTROL ▲▼ buttons.
H-POSITION H-WIDTH
Vertical position adjustment
Adjusts the vertical position and height of the screen.
Preparation Press the PROCEED button to display the main
menu.
Align the cursor with
1
Move the cursor left and right with the POSITION/CONTROL buttons.
V-HEIGHT is adjustable only in multiple mode.
Align the cursor with the desired item
 
V-POSITION V-HEIGHT
2
Move the cursor up and down with the POSITION/CONTROL ▲▼ buttons.
V-POSITION V-HEIGHT
Adjust with the POSITION/CONTROL
3
 
buttons
H-POSITION H-WIDTH
Press the EXIT button 2 times
4
Press the EXIT button one time to return to the main menu. One further press removes the menu.
Adjust with the POSITION/CONTROL
3
 
buttons
V-POSITION V-HEIGHT
Press the EXIT button 2 times
4
Press the EXIT button one time to return to the main menu. One further press removes the menu.
32
PLASMA MONITOR
Input Selection (INPUT SELECT)
This performs RGB 2 input selection and sets the SCART jack and VIDEO connector.
Preparation Press the PROCEED button to display the main menu.
Align the cursor with
1
Move the cursor left and right with the POSITION/CONTROL buttons.
 
INPUT SELECT
RGB2
: RGB
SCART
: OFF
VIDEO
: BNC
Align the cursor with the desired item
2
Move the cursor up and down with the POSITION/CONTROL ▲▼ buttons.
Adjust with the POSITION/CONTROL
3
 
buttons
RGB 2
Selects the signal connected to the RGB 2/DVD/HD IN con­nector. [RGB] : Set at time of RGB signal input [DVD/HD] : Set at time of DVD/HD signal input
INPUT SELECT
RGB2
: RGB
SCART
: OFF
VIDEO
: BNC
SCART
[OFF] : Set so that the SCART jack is not connected [ON] : Set to connect the SCART jack
* The SCART jack is not used in the United States. Normally
select [OFF]. If you select [ON], images will not be correctly displayed.
VIDEO
Select the connector that is assigned to the VIDEO input. [BNC] : The setting is to the VIDEO IN connector. [S-VIDEO] : The setting is to the S-VIDEO IN connector.
Press the EXIT button 2 times
4
Press the EXIT button one time to return to the main menu. One further press removes the menu.
PLASMA MONITOR
33
Standard Settings (NORMAL)
This returns the audio settings (SOUND), image adjustment (VISUAL CONTROL), horizontal/vertical position (H-POSITION and V-POSITION), auto picture/wide screen settings (AUTO PICTURE), menu display position adjustment (OSM LOCATION), and color temperature adjustments (COLOR TEMP) to the default settings.
Preparation Press the PROCEED button to display the main menu.
Align the cursor with
1
Move the cursor left and right with the POSITION/CONTROL buttons.
 
ALL RASTER NORMAL ALL VISUAL NORMAL ALL NORMAL
PROCEED TO RESET
Align the cursor with the desired item
2
Move the cursor up and down with the POSITION/CONTROL ▲▼ buttons.
Press the PROCEED button
ALL RASTER NORMAL ALL VISUAL NORMAL ALL NORMAL
PROCEED TO RESET
3
[ALL RASTER NORMAL]:
Returns the horizontal/vertical position adjust­ment, auto picture/wide screen settings, and menu position adjustment to the default settings.
[ALL VISUAL NORMAL]:
Returns the audio settings, image adjustments, and color temperature adjustment to the default settings.
[ALL NORMAL]:
Simultaneously returns the setting details of ALL RASTER NORMAL and ALL VISUAL NORMAL to the default settings.
Press the EXIT button 2 times
4
Press the EXIT button one time to return to the main menu. One further press removes the menu.
Note:
Functions that can be returned to the default settings
• ALL RASTER NORMAL
Horizontal position adjustment : H-POSITION
H-WIDTH (in multiple mode)
Vertical position adjustment : V-POSITION
V-HEIGHT (in multiple mode)
Auto picture/wide screen settings : AUTO PICTURE: ON (in single mode)
PICTURE ADJ FINE PICTURE
Menu position adjustment : H-POS
V-POS
• ALL VISUAL NORMAL
Audio settings : BALANCE Image adjustments : BRIGHTNESS
CONTRAST SHARPNESS COLOR TINT (SHARPNESS, COLOR, and TINT -­Only during video input)
Color temperature adjustment : COLOR TEMP
34
PLASMA MONITOR
Information Screen (DISPLAY MODE)
This permits a check of the signal (data) that is currently being input. Set [OSD MODE] to [PRO] on the configuration menu, then perform the following operations.
Preparation Press the PROCEED button to display the main menu.
Align the cursor with
1
Move the cursor left and right with the POSITION/CONTROL buttons.
Press the EXIT button
 
SOURCE INFO. RGB1 H-FREQ. V-FREQ. H-POL. V-POL.
31.5kHz
60.0Hz NEG POS
2
This removes the menu.
Note:
There is a slight error between the vertical frequency (V-FREQ.) displayed on the information screen and the actual vertical frequency of the con­nected input signal. A +/-3 Hz error exists for signals with a vertical frequency between 60 Hz and 70 Hz, and a +/-5 Hz error exists for signals with a vertical frequency above 70 Hz. Please regard the frequency indications of the information screen in terms of reference values only.
Information Screen
When RGB input is selected
[SOURCE INFO.]:
RGB 1, RGB 2, RGB 3, DVD/HD
[H-FREQ.] : Horizontal frequency
(kHz) [V-FREQ.] : Vertical frequency (Hz) [H-POL.] : Polarity of horizontal
sync signal
NEG (Negative)
POS (Positive) [V-POL.] : Polarity of vertical sync
signal
NEG (Negative)
POS (Positive)
Note:
[NO SIGNAL] is displayed when no signal is present.
When VIDEO input is selected
[SOURCE INFO.] :
VIDEO, SCART [MODE] : Color system standard
NTSC, PAL, SECAM
Note:
[NTSC] is displayed for 4.43 NTSC.
SOURCE INFO. RGB1 H-FREQ. V-FREQ. H-POL. V-POL.
SOURCE INFO. VIDEO
MODE : NTSC
31.5kHz
60.0Hz NEG POS
PLASMA MONITOR
35
Timer Settings (PRESENT TIME)
Time Settings
This sets the date and time. Set [OSD MODE] to [PRO] on the configuration menu, then per­form the following operations.
Preparation Press the PROCEED button to display the main
menu.
Align the cursor with
1
Move the cursor left and right with the POSITION/CONTROL buttons.
Align the cursor with AUTO PICTURE
 
PRESENT TIME DATE : 2001. AUG. 10 TIME : 22 : 30 SET
TIMER : OFF
2
Move the cursor as indicated below using the POSITION/ CONTROL ▲▼ buttons. [Year] [Month] [Day] [Hour] [Minute]
PRESENT TIME DATE : 2001. AUG. 10 TIME : 22 : 30 SET
TIMER : OFF
Timer Settings
This sets the date and time at which the power will be switched ON/OFF as well as the input mode. Set [OSD MODE] to [PRO] on the configuration menu, then per­form the following operations.
Preparation Press the PROCEED button to display the main
menu.
Align the cursor with
1
Move the cursor left and right with the POSITION/CONTROL buttons.
Align the cursor with TIMER
 
PRESENT TIME DATE : 2001. AUG. 10 TIME : 22 : 30 SET
TIMER : OFF
2
Move the cursor up and down with the POSITION/CONTROL ▲▼ buttons.
PRESENT TIME DATE : 2001. AUG. 10 TIME : 22 : 30 SET
TIMER : OFF
' PRESS PROCEED' FOR PROGRAM MENU
Set the numerical values with the
3
POSITION/CONTROL
Range of date and time settings
[Year] : 2000 to 2099 [Month] : JAN to DEC [Day] : 01 to 31 [Hour] : 00 to 24 [Minute] : 00 to 59
 
buttons
Align the cursor with SET and press the
4
PROCEED button
This will set the current time. Move the cursor up and down with the POSITION/CONTROL ▲▼ buttons.
Note:
Data can be maintained for about one month by the built-in battery when the power cable is disconnected. The built-in battery is not charged upon factory shipment. Charge it first. The battery is charged automatically when the AC cord plugged into a power outlet.
Turn the TIMER ON and OFF with the
3
POSITION/CONTROL
Each press of the POSITION/ CONTROL between [ON] and [OFF].
 
button switches
 
buttons
PRESENT TIME DATE : 2001. AUG. 10 TIME : 22 : 30 SET
TIMER : ON
' PRESS PROCEED' FOR PROGRAM MENU
Press the button and align the cursor
4
with the DATE item
This will display the sub menu.
PROGRAM MENU
ON
DATE
10:10
OCT30
22:15
JAN01
15:45
MON*
09:00
WED*
08:15
THU*
13:30
*
21:00
*
OFF 13:00 24:00 19:00 11:00 10:00 14:30 22:00
MODE VIDEO
INV
VIDEO
RGB1 RGB2
VIDEO
RGB1
36
PLASMA MONITOR
Timer Settings (PRESENT TIME)
Select the input method with the POSITION/CONTROL
5
▲▼ buttons, then press the EXIT button
[DIRECT] : Sets the desired date. [DAILY] : Sets daily. [WEEKLY] : Sets weekly.
1. DIRECT
2. DAILY
3. WEEKLY
DAILY
An asterisk " " is displayed after the date.
WEEKLY
Selects the week day. [MON] (Monday), [TUE] (Tuesday), [WED] (Wednesday), [THU] (Thursday), [FRI] (Friday), [SAT] (Saturday), [SUN] (Sunday) An asterisk " " is displayed after the week.
Align the cursor with the desired item
6
Move the cursor to the various items with the POSITION/CON-
 
TROL ▲▼
buttons.
Set the day and time values and the mode with the
7
PROCEED and POSITION/CONTROL
Date and time setting range (Numerical values are in­creased with the PROCEED button)
[Month] : JAN to DEC [Day] : 01 to 31 [Hour] : 00 to 24 [Minute] : 00 to 59
PROGRAM MENU
ON
DATE
10:10
OCT30
22:15
JAN01
15:45
MON*
09:00
WED*
08:15
THU*
13:30
*
21:00
*
 
MODE
OFF
VIDEO
13:00
INV
24:00
VIDEO
19:00
RGB1
11:00
RGB2
10:00
VIDEO
14:30
RGB1
22:00
buttons
* [INV] produces an inverse (negative/positive) display of
the screen to reduce image burn-in. The input mode at this time becomes that of the last input selected.
* [WT] produces an all-white screen display to reduce burn-
in.
* [RP] provides operation according to the repeat program
setting.
* [RI] provides operation according to the repeat program
and [INV] settings.
* [LUM.LIMIT] limits the screen brightness.
Repeat Program Setting
You can program to repeat switching screens within preset time. Moving the cursor to [RP] or [RI] displays the Repeat Program Set­ting screen. See the following for various settings.
(1) The power is switched ON when
[ON TIME] is reached.
(2) The screen of [MODE 1] is displayed
for the duration of [TIME 1].
(3) The screen of [MODE 2] is displayed
for the duration of [TIME 2].
(4) Steps (2) and (3) are repeated until
MODE SELECT MENU
MODE : RP
REPEAT PROGRAM
: VIDEO
MODE1
: 1 MIN
TIME1
: RGB2
MODE2
: 2 MIN
TIME2
[OFF TIME] is reached.
(5) The power is switched OFF when
[OFF TIME] is reached.
Press the EXIT button one time to return to the sub menu.
Press the EXIT button 3 times
8
Press the EXIT button one time to remove the sub menu. Press once more to return to the main menu.
One further press will remove the menu.
MODE (The PROCEED button displays the Mode Select
Menu and the
 
buttons change the numerical values.)
This selects the input mode that will be displayed when the timer is [ON]. Input modes that can be set will differ de­pending on the setting of [Input Selection].
SCART
RGB 2
OFF
ON
VIDEO, RGB 1,
RGB
DVD/HD
RGB 2, RGB 3, INV, WT, RP, RI, LUM.LIMIT
VIDEO, RGB 1, HD, RGB 3, INV, WT,
VIDEO, RGB 1, SC, RGB 3, INV, WT, RP, RI, LUM.LIMIT
RP, RI, LUM.LIMIT
Note:
Programs
Settings can be used in up to 7 programs. Program contents are deleted after exiting the program.
Monitor POWER/STANDBY Indicator
The POWER/STANDBY indicator blinks orange at 3-second intervals dur­ing the setting of the timer (at the time of monitor standby).
PLASMA MONITOR
37
4-Screen/9-Screen Multiple Screen Settings (VIDEO WALL MENU)
Only this monitor offers a system of 4 or 9 screens. This menu sets the screen mode (from among 1, 4, or 9 screens) as well as the position. See the Signal Identification For Raster Preset on Page 63 for information about supported signals. Set [OSD MODE] to [PRO] on the configuration menu, then perform the following operations.
Preparation Press the PROCEED button to display the main menu.
Align the cursor with
1
Move the cursor left and right with the POSITION/CONTROL buttons.
Align the cursor with SCREEN DIVIDER
 
VIDEO WALL MENU
1. SCREEN DIVIDER : 1
2. POSITION : NO. 1
3. DISP MODE : SPLIT
2
Move the cursor up and down with the POSITION/CONTROL ▲▼ buttons.
Use the POSITION/CONTROL
3
to set the number of screens
VIDEO WALL MENU
1. SCREEN DIVIDER : 1
2. POSITION : NO. 1
3. DISP MODE : SPLIT
 
buttons
Set the position of the screens with the
5
POSITION/CONTROL
4 screens
9 screens
NO.1 NO.2
NO.4 NO.3
NO.7 NO.8 NO.9
NO.10 NO.11 NO.12
NO.13 NO.14 NO.15
 
buttons
VIDEO WALL MENU
1. SCREEN DIVIDER : 4
2. POSITION : NO. 4
3. DISP MODE : SPLIT
Align the cursor with DISP MODE
6
VIDEO WALL MENU
1. SCREEN DIVIDER : 4
2. POSITION : NO. 4
3. DISP MODE : SPLIT
Set the screen mode with the POSITION/
7
CONTROL
 
buttons
[1] : 1 screen
(There is no POSITION setting.) [4] : 4 screens [9] : 9 screens
Align the cursor with POSITION
4
Move the cursor up and down with the POSITION/CONTROL ▲▼ buttons.
VIDEO WALL MENU
1. SCREEN DIVIDER : 4
2. POSITION : NO. 1
3. DISP MODE : SPLIT
VIDEO WALL MENU
1. SCREEN DIVIDER : 4
2. POSITION : NO. 1
3. DISP MODE : SPLIT
[SPLIT] : Combines enlarged screens and creates
multiple screens.
[BLANKING] : Corrects misalignment of combined screen
portions and creates multiple screens.
Press the EXIT button 2 times
8
Press the EXIT button one time to return to the main menu. One further press removes the menu.
38
PLASMA MONITOR
Menu Display Position Adjustment (OSM LOCATION)
This sets the display position of the menu and the display format (landscape or portrait) as well as the display time. Set [OSD MODE] to [PRO] on the configuration menu, then perform the following operations.
Preparation Press the PROCEED button to display the main
menu.
Align the cursor with
1
Move the cursor left and right with the POSITION/CONTROL buttons.
Align the cursor with the desired item
 
OSM H-POS OSM V-POS OSM ANGLE OSM DISPLAY TIME
2
Move the cursor up and down with the POSITION/CONTROL ▲▼ buttons.
OSM H-POS OSM V-POS OSM ANGLE OSM DISPLAY TIME
When the OSM DISPLAY TIME has been selected
This function permits setting the time until the menu display is au­tomatically deleted (in the absence of input operations).
Align the cursor with OSM DISPLAY
3
TIME
Move the cursor up and down with the POSITION/CONTROL ▲▼ buttons.
Set the time with the POSITION/CONTROL
4
 
buttons
[5] : 5 seconds [60] : 60 seconds [10] : 10 seconds [120] : 120 seconds [30] : 30 seconds
(Display Time Setting)
OSM H-POS OSM V-POS OSM ANGLE OSM DISPLAY TIME SECONDS:
5 10 30 60 120
Adjust with the POSITION/CONTROL
3
 
buttons
[OSM H-POS] : Adjusts the horizontal position of the menu display. [OSM V-POS] : Adjusts the vertical position of the menu display. [OSM ANGLE] : Sets the menu display format (to landscape [HOR]/
portrait [VER]).
[OSM DISPLAY TIME] : Sets the menu display time.
Press the EXIT button 2 times
4
Press the EXIT button one time to return to the main menu. One further press removes the menu.
Press the EXIT button 2 times
5
Press the EXIT button one time to return to the main menu. One further press removes the menu.
PLASMA MONITOR
39
Other Functions (OTHER SETTINGS)
Color System Settings (COLOR SYSTEM)
This function sets the color system (to AUTO, 3.58 NTSC, PAL, SECAM, or 4.43 NTSC). Set [OSD MODE] to [PRO] on the configuration menu, then per­form the following operations.
Preparation Press the PROCEED button to display the main
menu.
Align the cursor with
1
Move the cursor left and right with the POSITION/CONTROL buttons.
Align the cursor with COLOR SYSTEM
 
COLOR SYSTEM P-ON MODE POWER MANAGER SET ID NO RGB3 ADJUST CINEMA PULLDOWN STD/CINEMA ALL RESET
: AUTO
: LAST MEM
: OFF : ALL : 1 : ON : STD
2
Move the cursor up and down with the POSITION/CONTROL ▲▼ buttons.
COLOR SYSTEM P-ON MODE POWER MANAGER SET ID NO RGB3 ADJUST CINEMA PULLDOWN STD/CINEMA ALL RESET
: AUTO
: LAST MEM
: OFF : ALL : 1 : ON : STD
Power-On Mode Setting (P-ON MODE)
This function sets the input mode at the time the power is switched on. Set [OSD MODE] to [PRO] on the configuration menu, then per­form the following operations.
Preparation Press the PROCEED button to display the main
menu.
Align the cursor with
1
Move the cursor left and right with the POSITION/CONTROL buttons.
Align the cursor with P-ON MODE
 
COLOR SYSTEM P-ON MODE POWER MANAGER SET ID NO RGB3 ADJUST CINEMA PULLDOWN STD/CINEMA ALL RESET
: LAST MEM
: AUTO
: OFF : ALL : 1 : ON : STD
2
Move the cursor up and down with the POSITION/CONTROL ▲▼ buttons.
COLOR SYSTEM P-ON MODE POWER MANAGER SET ID NO RGB3 ADJUST CINEMA PULLDOWN STD/CINEMA ALL RESET
: AUTO
: LAST MEM
: OFF : ALL : 1 : ON : STD
Set the color system with the POSITION/
3
CONTROL
[AUTO] : Automatically detects the color system and
[3.58 NTSC]
[PAL] : [SECAM] : Standard system for mainly France and Russia. [4.43 NTSC]
: Standard system for mainly North America and
: System mainly used in VTRs in PAL/SECAM
 
buttons
selects it.
Japan. Standard system for mainly the UK and Germany.
regions.
Press the EXIT button 2 times
4
Press the EXIT button one time to return to the main menu. One further press removes the menu.
* Aligning the cursor with [ALL RESET] and pressing the
PROCEED button will return all the settings of the other functions to the default settings.
Set the P-ON MODE with the POSITION/
3
CONTROL
The mode that is displayed will be as indicated below accord­ing to the setting of [Input Selection].
SCART
RGB 2
RGB
DVD/HD
[LAST MEM] : This is the input mode that was last selected
[VIDEO] : This results in the VIDEO input mode. [RGB 1] : This results in the RGB 1 input mode. [RGB 2] : This results in the RGB 2 input mode. [RGB 3] : This results in the RGB 3 input mode. [DVD/HD] : This results in the DVD/HD input mode. [SCART] : This results in the SCART jack input mode.
 
buttons
OFF
LAST MEM, VIDEO, RGB 1, RGB 2, RGB 3
LAST MEM, VIDEO RGB 1, HD/DVD, RGB 3
(at the time the power was switched off). (Last Memory)
ON
LAST MEM VIDEO, RGB 1, SCART, RGB 3
40
PLASMA MONITOR
Other Functions (OTHER SETTINGS)
Power Management Settings (POWER MANAGER)
This sets the functions that serve to automatically reduce power consumption. Set [OSD MODE] to [PRO] on the configuration menu, then per­form the following operations.
Preparation Press the PROCEED button to display the main
menu.
Press the EXIT button 2 times
4
Press the EXIT button one time to return to the main menu. One further press removes the menu.
* Aligning the cursor with [ALL RESET] and pressing the PRO-
CEED button will return all the settings of the other functions to the default settings.
Align the cursor with
1
Move the cursor left and right with the POSITION/CONTROL buttons.
Align the cursor with POWER MANAGER
 
COLOR SYSTEM P-ON MODE POWER MANAGER SET ID NO RGB3 ADJUST CINEMA PULLDOWN STD/CINEMA ALL RESET
2
Move the cursor up and down with the POSITION/CONTROL ▲▼ buttons.
Set the power management mode with
3
the POSITION/CONTROL
COLOR SYSTEM P-ON MODE POWER MANAGER SET ID NO RGB3 ADJUST CINEMA PULLDOWN STD/CINEMA ALL RESET
 
buttons
: AUTO
: LAST MEM
: OFF : ALL : 1 : ON : STD
: AUTO
: LAST MEM
: OFF : ALL : 1 : ON : STD
[ON] : Power management function operates. [OFF] : Power management is cancelled.
Press the EXIT button 2 times
4
Press the EXIT button one time to return to the main menu. One further press removes the menu.
* Aligning the cursor with [ALL RESET] and pressing the PRO-
CEED button will return all the settings of the other functions to the default settings.
PLASMA MONITOR
41
Other Functions (OTHER SETTINGS)
POWER/STANDBY Indicator
The status of the power management function can be checked with the POWER/STANDBY indicator of the monitor.
Power Manage-
ment Mode
On State
Standby State
Suspend State
Off State
Note:
Power Management Function
The power management function is an energy-saving function that au-
tomatically reduces the power consumption of the monitor when the keyboard or mouse have not been operated for a fixed period. This function becomes valid when combined with a personal computer that is based on the VESA DPMS system.
When power is not being supplied to the personal computer or when
the personal computer and this monitor are not properly connected, the power management function will operate and this monitor will en­ter the "off state."
Please see your personal computer user's manual for information about
the power management function of the personal computer side.
During power management mode the fan may stop, but this is not a
malfunction.
POWER/STANDBY
Indicator
Green
Yellow
Orange
Orange
Power Management
Operation Status
Not operating
Operating
Operating
Operating
Details
Horizontal/vertical sync sig­nals are being input from the personal computer.
Horizontal sync signal is not being input from the personal computer.
Vertical sync signal is not being input from the personal computer.
Horizontal/vertical sync sig­nals are not being input from the personal computer.
Not required since the personal computer is nor­mally being used at this time.
Press a keyboard key or move the mouse. The screen will be displayed immediately.
Press a keyboard key or move the mouse. The screen will be displayed; however, it will take some time from the standby state until the screen is dis­played.
Press a keyboard key or move the mouse. The screen will be displayed; however, it will take some time from the standby state until the screen is dis­played.
Recovery Method
42
PLASMA MONITOR
Other Functions (OTHER SETTINGS)
ID Number Setting (SET ID NO)
Important
When using more than one of these monitors, this function sets ID numbers so that operation of the remote control does not cause multiple monitors to operate at the same time. (These ID numbers can also be used for control with RS-232C.) The optional remote control is required to operate the plasma monitors for each ID number independently. (These ID numbers also need to be assigned.)
Set [OSD MODE] to [PRO] on the configuration menu, then per­form the following operations.
Preparation Press the PROCEED button to display the main
menu.
Align the cursor with
1
Move the cursor left and right with the POSITION/CONTROL buttons.
Align the cursor with SET ID NO
 
COLOR SYSTEM P-ON MODE POWER MANAGER SET ID NO RGB3 ADJUST CINEMA PULLDOWN STD/CINEMA ALL RESET
: AUTO
: LAST MEM
: OFF : ALL : 1 : ON : STD
2
Move the cursor up and down with the POSITION/CONTROL ▲▼ buttons.
COLOR SYSTEM P-ON MODE POWER MANAGER SET ID NO RGB3 ADJUST CINEMA PULLDOWN STD/CINEMA ALL RESET
: AUTO
: LAST MEM
: OFF : ALL : 1 : ON : STD
RGB 3 Adjustment (RGB 3 ADJUST)
Adjust this setting when the RGB 3 image is not stable. Set [OSD MODE] to [PRO] on the configuration menu, then per­form the following operations.
Preparation Press the PROCEED button to display the main
menu.
Align the cursor with
1
Move the cursor left and right with the POSITION/CONTROL buttons.
Align the cursor with RGB 3 ADJUST
 
COLOR SYSTEM P-ON MODE POWER MANAGER SET ID NO RGB3 ADJUST CINEMA PULLDOWN STD/CINEMA ALL RESET
: LAST MEM
: AUTO
: OFF : ALL : 1 : ON : STD
2
Move the cursor up and down with the POSITION/CONTROL ▲▼ buttons.
Use the POSITION/CONTROL
3
the number that provides the best image
When the screen is not stable at [1] (the initial value), set the adjustment to [2] or [3].
COLOR SYSTEM P-ON MODE POWER MANAGER SET ID NO RGB3 ADJUST CINEMA PULLDOWN STD/CINEMA ALL RESET
 
buttons to set
: AUTO
: LAST MEM
: OFF : ALL : 1 : ON : STD
Set the ID number with the
3
POSITION/CONTROL
[ALL] : ID number will not be set. [001 to 256]: ID number will be set.
 
buttons
Press the EXIT button 2 times
4
Press the EXIT button one time to return to the main menu. One further press removes the menu.
* Aligning the cursor with [ALL RESET] and pressing the PRO-
CEED button will return all the settings of the other functions to the default settings. (The ID number will become [ALL].)
Press the EXIT button 2 times
4
Press the EXIT button one time to return to the main menu. One further press removes the menu.
* Aligning the cursor with [ALL RESET] and pressing the PRO-
CEED button will return all the settings of the other functions to the default settings.
Note:
Making this adjustment will cause the display position to change. To com­pensate, set [AUTO PICTURE] (of the [Auto Picture/Wide Screen Settings]) to [OFF] and then to [ON], or readjust the display position.
PLASMA MONITOR
43
Other Functions (OTHER SETTINGS)
Cinema Pulldown Setting (CINEMA PULLDOWN)
This function sets the cinema pulldown in conjunction with the video information that is recorded on the DVD software. This is valid only for NTSC, PAL, and 480I (60 Hz) signals. Set [OSD MODE] to [PRO] on the configuration menu, then perform the following operations.
Preparation Press the PROCEED button to display the main
menu.
Align the cursor with
1
Move the cursor left and right with the POSITION/CONTROL buttons.
Align the cursor with CINEMA PULLDOWN
 
COLOR SYSTEM P-ON MODE POWER MANAGER SET ID NO RGB3 ADJUST CINEMA PULLDOWN STD/CINEMA ALL RESET
: AUTO
: LAST MEM
: OFF : ALL : 1 : ON : STD
2
Move the cursor up and down with the POSITION/CONTROL ▲▼ buttons.
COLOR SYSTEM P-ON MODE POWER MANAGER SET ID NO RGB3 ADJUST CINEMA PULLDOWN STD/CINEMA ALL RESET
: AUTO
: LAST MEM
: OFF : ALL : 1 : ON : STD
Standard/Cinema Image Settings (STD/CINEMA)
To display clearer images, settings are made with the standard image and cinema image modes. Set to [CINEMA] for images such as mov­ies, and set to [STD] for other images. Set [OSD MODE] to [PRO] on the configuration menu, then perform the following operations.
Preparation Press the PROCEED button to display the main
menu.
Align the cursor with
1
Align the cursor with STD/CINEMA
2
Move the cursor up and down with
 
: AUTO
: LAST MEM
: OFF : ALL : 1 : ON : STD
the POSITION/CONTROL ▲▼ buttons.
COLOR SYSTEM P-ON MODE POWER MANAGER SET ID NO RGB3 ADJUST CINEMA PULLDOWN STD/CINEMA ALL RESET
Use the POSITION/CONTROL
3
buttons to set STD/CINEMA
[STD] : Set for varieties of input other than that described
below.
[CINEMA] : Set for image inputs such as movies.
Set the cinema pulldown with the
3
POSITION/CONTROL
[ON] : Cinema pulldown is active.
Detects whether film recording software or video recording software was used. When film record­ing software was used, it is progressively dis­played with 2-3 pulldown or 2-2 pulldown.
[OFF] : Cinema pulldown is cancelled.
There is a progressive display without 2-3 pulldown or 2-2 pulldown.
 
buttons
Press the EXIT button 2 times
4
Press the EXIT button one time to return to the main menu. One further press removes the menu.
* Aligning the cursor with [ALL RESET] and pressing the PRO-
CEED button will return all the settings of the other functions to the default settings.
Press the EXIT button 2 times
4
Press the EXIT button one time to return to the main menu. One further press removes the menu.
* Aligning the cursor with [ALL RESET] and pressing the PRO-
CEED button will return all the settings of the other functions to the default settings.
Note:
What is CINEMA PULLDOWN?
This is a mode to output DVD video information in a progressive signal format.
CINEMA PULLDOWN
[ON] Normally set to [ON]. This setting detects whether a DVD source was based on film or video. When it was based on film, it will be progres­sively displayed in the appropriate method.
[OFF] This setting is used for video source on DVD, converting into the pro­gressive output.
44
PLASMA MONITOR
Long Life Settings (LONG LIFE MODE)
Long Life Settings (LONG LIFE MODE)
These settings reduce screen burn-in. Set [OSD MODE] to [PRO] on the configuration menu, then per­form the following operations.
Preparation Press the PROCEED button to display the main menu.
Align the cursor with
1
Move the cursor left and right with the POSITION/CONTROL buttons.
 
Align the cursor with the desired item
LONG LIFE MODE LUM. LIMIT ORBITTING INV / WT
PROG. ORBIT . . . . . . . .
GRAY LEVEL ALL RESET
2
Move the cursor up and down with the POSITION/CONTROL ▲▼ buttons. [LUM. LIMIT]:
Suppresses the brightness of the screen.
[ORBITING]:
Moves the screen at a fixed pe­riod. * Cannot be set at the time of the 4-screen/9-screen
multiple system setting.
[INV/WT]:
Displays a negative/positive inverse image or an all-white screen. * The [INV] and [WT] settings will be switched to [OFF]
when the power is switched on or off, and at the time of input signal selection. The last operating condition data will not be stored in memory.
[PROG. ORBIT...➝]:
Align the cursor with [PROG. ORBIT...] and press the PROCEED button. The PROG. ORBIT MENU screen is displayed and the movement of screen dots can be set to be programmable. * When either [ORBITING] or [PROG. ORBIT] is set to
[ON], the other one will be [OFF]. Note that if [PROG. ORBIT] is set to [ON], the dot display of
*
the set portion will be lost on the screen
* This setting is not available when the 4-screen/9-screen
multiple system is set.
LONG LIFE MODE
LUM. LIMIT ORBITTING INV / WT
PROG. ORBIT . . . . . . . .
GRAY LEVEL ALL RESET
: OFF : OFF : OFF
: 3
: OFF : OFF : OFF
: 3
Set the long life mode with the POSI-
3
TION/CONTROL
[LUM. LIMIT] and [ORBITING] settings
[ON] : Long life function is operational. [OFF] : Cancelled
[INV/WT] settings
[INV] : Provides the negative/positive inverse image of the
screen. [WT] : Displays an all-white screen. [OFF] : Cancelled
[PROG. ORBIT...] settings
[SET] :
[ON] : Function is operational. [OFF] : Cancelled.
[H-DOT] :
Moves from 1 to 20 dots in the horizontal direction.
[V-LINE] :
Moves from 1 to 20 dots in the vertical direction.
[TIME] :
A 1- to 5-minute interval between movements.
 
buttons
PROG. ORBIT MENU
SET
H-DOT V-LINE TIME
: OFF
: 5 : 5 : 1
Press the EXIT button 2 times
4
Press the EXIT button one time to return to the main menu. One further press removes the menu.
* Aligning the cursor with [ALL RESET] and pressing the PRO-
CEED button will return all long life settings to the default settings.
Important
Regarding Copyright
Please note that using this monitor for the purpose of commercial gain or the attraction of public attention in a venue such as a coffee shop or hotel and employing compression or expansion of the screen image with a wide screen setting (of FULL, ZOOM, or STADIUM), etc., raises concern about the infringement of copyright rights which are protected by copy­right law.
PLASMA MONITOR
45
Long Life Settings (LONG LIFE MODE)
Gray Level Settings (GRAY LEVEL)
In [NORMAL] and other modes, this adjusts the brightness of non-image portions that appear at top, bottom, left, or right of the screen. Set [OSD MODE] to [PRO] on the configuration menu, then perform the following operations. * Gray level settings cannot be made in 4-screen or 9-screen systems.
Preparation Press the PROCEED button to display the main
menu.
Align the cursor with
1
Move the cursor left and right with the POSITION/CONTROL buttons.
 
Align the cursor with the desired item
LONG LIFE MODE LUM. LIMIT ORBITTING INV / WT
PROG. ORBIT . . . . . . . .
GRAY LEVEL ALL RESET
2
Move the cursor up and down with the POSITION/CONTROL ▲▼ buttons.
Set the gray level with the POSITION/
3
CONTROL
 
buttons
LONG LIFE MODE
LUM. LIMIT ORBITTING INV / WT
PROG. ORBIT . . . . . . . .
GRAY LEVEL ALL RESET
: OFF : OFF : OFF
: 3
: OFF : OFF : OFF
: 3
Important
Gray Level Settings
The gray level can be set to suit the level of gray brightness desired by the user. There are marked differences in brightness between the display portions and non-display portions (where there is no image) in [NORMAL] mode which result in image burn-in due to strong contrast. In view of this, the following settings are strongly recommended. Note that image burn-in will still occur, though somewhat later, even after making these settings and that burn-in cannot be suppressed. The moni­tor should be used in [FULL] mode as much as possible.
1. Perform gray level settings to narrow the differences in brightness be­tween display and non-display portions of the image.
2. Weaken the image adjustment contrast and brightness. (See P.28)
3. Perform the Long Life settings. (P.45)
[1] : Black [2] : Gray [3] : Light gray
Press the EXIT button 2 times
4
Press the EXIT button one time to return to the main menu. One further press removes the menu.
* Aligning the cursor with [ALL RESET] and pressing the PRO-
CEED button will return all long life settings to the default settings.
46
PLASMA MONITOR
Color Temperature Adjustment (COLOR TEMP)
This adjusts the tone of white. Set [OSD MODE] to [PRO] on the configuration menu, then per­form the following operations.
When User 1 to 4 Has Been Selected (User Settings)
Preparation Press the PROCEED button to display the main
menu.
Align the cursor with
1
Move the cursor left and right with the POSITION/CONTROL buttons.
Align the cursor with COLOR TEMP
 
COLOR TEMP
2
Move the cursor up and down with the POSITION/CONTROL ▲▼ buttons.
COLOR TEMP
HIGH LOW
USER1
Permits a detailed adjustment of the white balance. Allows storage of adjustment values from 1 to 4.
Align the cursor with USER 1 to 4, then
3
press the PROCEED button
Move the cursor left and right with the POSITION/CONTROL buttons. Each button press changes the setting by one step.
HIGH LOW
USER 4 USER 2
USER 3
 
USER 1
COLOR TEMP
HIGH LOW
' PRESS PROCEED' FOR GAIN / BIAS SETTING
Select the setting item with the
4
POSITION/CONTROL ▲▼ buttons
Image when bright
[R-GAIN] : Adjustment of red gain [G-GAIN] : Adjustment of green gain [B-GAIN] : Adjustment of blue gain
Image when dark [R-BIAS] : Adjustment of red bias [G-BIAS] : Adjustment of green bias [B-BIAS] : Adjustment of blue bias
R-GAIN (WHITE LEVEL) G-GAIN (WHITE LEVEL) B-GAIN (WHITE LEVEL)
R-BIAS (BLACK LEVEL) G-BIAS (BLACK LEVEL) B-BIAS (BLACK LEVEL)
USER1
Make the setting with the POSITION/
3
CONTROL
[HIGH] : Produces a white with a strong blue content. [LOW] : Produces a white with a strong red content. [USER 1 to 4] : Displays a white balance adjustment screen.
 
buttons
Press the EXIT button 2 times
4
Press the EXIT button one time to return to the main menu. One further press removes the menu.
Adjust with the POSITION/CONTROL
5
 
buttons
Press the EXIT button 3 times
6
Press the EXIT button one time to remove the setting menu. Press once more to return to the main menu. One further press removes the menu.
PLASMA MONITOR
47
Appendix
Opening the Terminal Cover
When connecting signal or other cables, the terminal cover of the monitor terminal section is opened to allow the connection to be made. After making the connection, close the terminal cover to permit cables to be arranged.
Terminal cover
Raise the tab at the side of the terminal cover and open the ter-
1
minal cover at the same time.
Release the tab.
2
Ta b
Closing the Terminal Cover
Raise the tab at the side of the terminal cover and close the ter-
1
minal cover at the same time.
Release the tab.
2
Mounting of the Remote Control Holder
A remote control holder can be mounted which will allow the remote control to be stored away when it isn't being used.
Remote control holder
Insert the top portion of the remote control holder into the (up-
1
per side) mounting holes at the left of the monitor terminal sec­tion.
Insert the bottom portion of the remote control holder into the
2
(lower side) mounting holes. (Insert until an engagement click is heard.)
1
2
Push up the bottom portion of the remote control holder and
1
disengage it.
Disengage the upper portion of the remote control holder.
2
Removing the Remote Control Holder
48
PLASMA MONITOR
Placing the Remote Control into the Remote Control Holder
The remote control can be stored away in the remote control holder when not in use.
Insert the bottom portion of the remote control into the bottom
1
portion of the remote control holder.
Insert the upper portion of the remote control into the upper por-
2
P
O
W
E
R O
F
F
PO
W
ER
O
N
R
GB
2
/
D
VD
/
H
D
RGB 1
RGB 3
VIDEO
EXIT
P
R
O
C
POSITION
E
E
D
/
CONTROL
RP
­102
tion of the remote control holder. (Insert until an engagement click is heard.)
Removing the Remote Control
Lift the upper portion of the remote control.
1
Disengage the lower part of the remote control from the remote
2
control holder.
Appendix
PLASMA MONITOR
49
Appendix
Attaching the Ferrite Cores
Attach the ferrite cores to the power cable and the DVI signal cable. Use of the cables without mounting the ferrite cores will result in the occurrence of noise.
Power cable DVI signal cable
Open the ferrite cores and clamp them on
1
the power cable.
Ferrite core
Power cable
Open the ferrite cores and clamp them on
1
the DVI signal cable.
Close the ferrite cores.
2
Close the ferrite cores.
2
Mounting Positions of Ferrite Cores and Cable Ties
Attach the large ferrite core at the end of the power cable that is close to the monitor. Attach one small ferrite core to each end of the DVI signal cable.
Fix the ferrite cores in place with cable ties
3
so that they do not shift.
Ferrite core
DVI signal cable
Cable tie
Power cable
Ferrite core (Large)
To power outlet
DVI signal cable
Ferrite core (Small)
To equipment with a digital interface
Cable tie
Ferrite core (Large)
Ferrite core (Small)
Cable tie
To AC IN connector of monitor
To the RGB 3 connector of this monitor
50
PLASMA MONITOR
Appendix
Pin Configuration and Signal Level of Mini D-Sub 15-Pin (Analog) Input Connector
RGB1
2
4
3
5
10
15
Signal level
VIDEO signal : 0.7Vp-p (Analog) Sync signal : TTL level
1
6
8
9
7
121314
11
Pin No. Signal (Analog)
1Red 2 Green or sync-on-green 3 Blue 4 Ground 5 Ground 6 Red ground 7 Green ground 8 Blue ground
9 No connection 10 Sync signal ground 11 Ground 12 Bi-directional DATA (SDA) 13 Horizontal or composite sync 14 Vertical sync 15 Data clock
Pin Configuration and Functions of External Control Connector (Mini D-Sub 9 -Pin)
Application
These specifications are applicable to NEC plasma monitors (including 42- and 50-inch types) and communications control from external equipment.
Connections
Connections should be made as described below.
External equipment e.g., Personal computer
PDP1 Display
*A maximum of 4 units can used with a cascade connection.
1)Display-side connector: EXTERNAL CONTROL connector
EXTERNAL CONTROL
45321
6789
2)External equipment side connector: Serial port (RS-232C) connector See the specifications of the connected equipment for information about the type of connector and pin assignment.
3)Wiring
Use a crossed (reverse) cable.
Wire the cable so that each pair of data lines cross between the two devices. These data line pairs are RXD (Receive data) and TXD (Transmit data), DTR (DTE side ready) and DSR (DCE side ready), and RTS (Ready to send) and CTS (Clear to send).
PDP3 DisplayPDP2 Display PDP8 Display PDP9 Display
PDP4 Display
Pin No. Function
1 No connection 2 RXD (Receive data) 3 TXD (Transmit data) 4 No connection 5 Ground 6 No connection 7 RTS (Ready to send) * Connected internally to pin 8. 8 CTS (Clear to send) * Connected to pin 7 inside the main unit. 9 No connection
PLASMA MONITOR
51
Appendix
Communication Parameters
(1) Communication system Asynchronous (2) Interface RS-232C (3) Baud rate 9600 bps (4) Data length 8 bits (5) Parity Odd (6) Stop bit 1 bit (7) Communication code Hex
Communication Format
8bit 8bit 8bit 8bit 8bit 8bit 8bit 8bit
Check Sum
Data
UNIT ID 1
Command 1
Data length
Command 2
UNIT ID 2
Command 1
Together with Command 2, this is a number that distinguishes the various commands. For ACK, when bit 2 and bit 3 are both “1”, reception of a sup­ported command or data is indicated. When bit 2 is “0”, reception of an unsupported command or data is indicated. Bit 0 and bit 1 should be set as described below.
bit0
0 0 1 1
* When normally selecting one screen, ID or multiple
screen(VIDEO WALL), set bit 0 and bit 1 of Command 1.
bit1
0 1 0 1
When multiple screens are selected Not used At time of set ID selection At time of regular use
Check Sum (CKS), Error Processing, and ACK
1)Checks that received data incorporates both the following checksum and RS-232C (odd) parity. The checksum comprises the following aspects of one transmit­ted or received frame: Command 1, Unit 1 and 2, Command 2, data length, and the lower order 8 bits of the total data.
Check Sum Example
9FH 40H 4FH 01H 01H 30H Command 1 Unit ID Command 2 Data Length Data Check Sum
Total 130H
2)Error Processing (1) When the communications interval is 4 ms or greater, the
arrival of a subsequent Command 1 will be recognized. If meaningful data cannot be discerned at this time, that data will not be recognized.
(2) When the receive data error, checksum error, and the re-
ceive data could not all be taken in, ACK is not returned.
3)Returning an ACK
When command processing exceeds 0.5 seconds following command reception, an ACK1 for which bit 3 of Command 1 has been set to “0” (during command processing) is returned every 0.5 seconds until command processing is completed. When command processing is completed, an ACK2 for which bit 3 of Command 1 has been set to “1” (at the end of command processing) is returned every 0.5 seconds until command pro­cessing is completed. Bit 1 of Command 1 is set to 0 ; when the UA2 setting is FFH, it is possible to simultaneously operate all sets connected in cascade and as a result, ACK is not returned.
Example: CFH for powering on (Command 1) CFH 1111 1111 (CFH): At time of regular use
1111 1110 (CEH): Not used 1111 1101 (CDH): At time of set ID selection 1111 1100 (CCH): When multiple screens are selected
The same goes for 0FH, 4FH, 8FH and DFH other than Command
1.
Unit ID 1 and Unit ID 2
1)Unit ID1: Sets a number corresponding to the various sets ID (1 through 4) when multiple screens are selected, and to 1 through 256 at the time of set ID selection. “00H” must be output when the ID is not set.
2)Unit ID2: Makes settings on the occasion of simultaneously operating all sets connected in cascade at the time of multiple screen mode and at the time of set ID selection.
Selection of all sets: FFH At time of regular setting: 00H
Command 2
Together with Command 1, this is a number that distinguishes the various commands.
Communications Flow
Personal computer
Plasma display
Various commands
When various commands are sent from a personal computer (PC) or other external equipment, the display is always ready to receive them. Note that resending of the command is recommended when an ACK is not returned from the display within 1.5 seconds.
PC or other external equipment
ACK
52
PLASMA MONITOR
Appendix
Command Reference List
CMD1 CMD2 LEN
01. Connect Request 4FH 39H 01H
02. Running Sense 4FH 88H 00H
03. Power ON 8FH 4EH 00H
04. Power OFF 8FH 4FH 00H
05. Input Switch Change CFH 50H 01H
06. COLOR TEMP Select CFH 00H 01H
07. RED Gain Data CFH 10H 04H
08. GREEN Gain Data CFH 11H 04H
09. BLUE Gain Data CFH 12H 04H
10. GAMMA Gain Data CFH 13H 03H
11. COLOR Gain Data CFH 14H 03H
12. TINT Gain Data CFH 15H 03H
13. SHARPNESS Gain Data CFH 16H 03H
14. CONTRAST Gain Data CFH 17H 03H
15. BRIGHT Gain Data CFH 18H 03H
16. V.POS Gain Data CFH 19H 03H
17. H.POS Gain Data CFH 1AH 04H
18. PHASE Gain Data CFH 1BH 03H
19. CLOCK Gain Data CFH 1CH 03H
20. ––
21. ––
22. V-HEIGHT Gain Data CFH 1FH 03H
23. H-WIDTH Gain Data CFH 20H 03H
24. TIMER SWITCH CFH 02H 01H
25. AUTO PICTURE Select CFH 57H 02H
26. RESET OFH 54H 01H
27. COLOR SYSTEM Select CFH 5CH 01H
28. INPUT MODE Request 0FH 41H 00H
29. SCREEN MODE Request 0FH 42H 00H
30. VIDEO ADJ Request 0FH 45H 00H
31. SCREEN ADJ Request 0FH 47H 00H
32. COLOR SYSTEM Request 0FH 4CH 00H
33. FAILURE MODE Inform 0FH 3FH 00H
34. SET CONDITION Inform 0FH 40H 00H
35. SIGNAL Inform 0FH 3EH 00H
36. SETTING MODE Select CFH 04H 02H
37. SCREEN MODE Select CFH 51H 01H
38. PICTURE Mute On 8FH 3CH 00H
39. PICTURE Mute Off 8FH 3DH 00H
40. MULTI MODE Select CFH 03H 02H
41. MULTI MODE Request 0FH 3BH 00H
42. OSM SELECT DFH 58H 01H
43. VOLUME Gain Data CFH 21H 03H
44. SOUND INPUT Select CFH 05H 02H
45.
VOLUME
Gain Data
46.
SOUND INPUT SELECT Request
47. CONFIG MENU Select CFH 06H 01H
48. TIMER PROGRAM Setting CFH 08H 0CH
49. MULTI DISP MODE Select CFH 07H 02H
50. MULTI DISP MODE Request 0FH 61H 00H
51. PRESENT TIME Setting CFH 09H 0AH
Request
0FH 46H 00H 0FH 60H 00H
01. Connect Request
Function
The external control equipment requests a communications connec­tion from the display. When the display has received this command, it returns an ACK to the external control equipment and notifies that the connection is com­pleted.
Transmission Data
4FH UA1 UA2 39H 01H 00H CKS
CKS : Checksum
ACK
0FH UA2 UA2 39H 00H CKS
02. Running Sense
Function
The external control equipment ascertains the power supply condition of the display and then causes the display to recognize the PC CON­TROL connection.
Transmission Data
4FH UA1 UA2 88H 00H CKS
ACK
0FH UA1 UA2 88H 01H DATA CKS
DATA:
Bit0 : Connect Condition
0 : No connection 1 : Connected
Bit1 0 : Fixed
1 : -
Bit2 : Power Status
0 : POWER ON 1 : POWER OFF(STANDBY)
Bit3 0 : Fixed
1 : –
Bit4 0 : Fixed
1 : –
Bit5 0 : Fixed
1 : –
Bit6 0 : Fixed
1 : –
Bit7 0 : Fixed
1 : –
03. Power ON
Function
The external control equipment switches on the power of the display.
Transmission Data
8FH UA1 UA2 4EH 00H CKS
ACK
The display returns the following ACK when the power is switched on:
2FH UA1 UA2 4EH 00H CKS
04. Power OFF
Function
The external control equipment switches off the power of the display.
Transmission Data
8FH UA1 UA2 4FH 00H CKS
ACK
The display returns the following ACK when the power is switched off:
2FH UA1 UA2 4FH 00H CKS
PLASMA MONITOR
53
Appendix
05. Input Switch Change
Function
The external control equipment switches the input of the display.
Transmission Data
CFH UA1 UA2 50H 01H DATA CKS
DATA : Input Select
01H : Video 07H : RGB1 08H : RGB2 0CH : RGB3 05H : HD/DVD 0FH : SCART
ACK
There is no ACK for which input was selected.
2FH UA1 UA2 50H 00H CKS
06. COLOR TEMP Select
Function
The external control equipment changes the COLOR TEMP of the display.
Transmission Data
CFH UA1 UA2 00H 01H DATA00 CKS
DATA00
00H : HIGH 01H : LOW 02H : USER1 03H : USER2 04H : USER3 05H : USER4
ACK
6FH UA1 UA2 00H 01H DATA00 CKS
DATA00 :
00H : HIGH 01H : LOW 02H : USER1 03H : USER2 04H : USER3 05H : USER4
NOTE: When HIGH or LOW is selected with COLOR TEMP, changes of the R/G/B GAIN data will not be received.
07. RED Gain Data
Function
The external control equipment changes the RED gain data of the display. (This command will be received only when COLOR TEMP is set for USER 1-4.)
Transmission Data
CFH UA1 UA2 10H 04H DATA00–DATA03 CKS
DATA00 : USER PICTURE Gain Flag
01H
DATA01 : RED Gain Flag
01H
DATA02 : RED Gain
E0H : -32 | FFH : -1 00H : 0 | 20H : +32
DATA03 : RED Bias
E0H : -32 | FFH : -1 00H : 0 | 20H : +32
ACK
6FH UA1 UA2 10H 02H DATA00 DATA01 CKS
DATA00 : USER PICTURE Gain Flag
01H
DATA01 : RED Gain Flag
01H
08. GREEN Gain Data
Function
The external control equipment changes the GREEN gain data of the display. (This com­mand will be received only when COLOR TEMP is set for USER 1-4.)
Transmission Data
CFH UA1 UA2 11H 04H DATA00–DATA03 CKS
DATA00 : USER PICTURE Gain Flag
01H
DATA01 : GREEN Gain Flag
02H
DATA02 : GREEN Gain
E0H : -32 | FFH : -1 00H : 0 | 20H : +32
DATA03 : GREEN Bias
E0H : -32 | FFH : -1 00H : 0 | 20H : +32
ACK
6FH UA1 UA2 11H 02H DATA00 DATA01 CKS
DATA00 : USER PICTURE Gain Flag
01H
DATA01 : GREEN Gain Flag
02H
09. BLUE Gain Data
Function
The external control equipment changes the BLUE gain data of the display. (This command will be received only when COLOR TEMP is set for USER 1-4.)
Transmission Data
CFH UA1 UA2 12H 04H DATA00–DATA03 CKS
DATA00 : USER PICTURE Gain Flag
01H
DATA01 : BLUE Gain Flag
03H
DATA02 : BLUE Gain
E0H : -32 | FFH : -1 00H : 0 | 20H : +32
DATA03 : BLUE Bias
E0H : -32 | FFH : -1 00H : 0 | 20H : +32
ACK
6FH UA1 UA2 12H 02H DATA00 DATA01 CKS
DATA00 : USER PICTURE Gain Flag
01H
DATA01 : BLUE Gain Flag
03H
10. GAMMA Gain Data
Function
The external control equipment changes the GAMMA gain data of the display.
Transmission Data
CFH UA1 UA2 13H 03H DATA00–DATA02 CKS
DATA00 : USER PICTURE Gain Flag
01H
DATA01 : Gamma Gain Flag
09H
DATA02 : D-Gamma
00H : OFF 01H : ON
ACK
6FH UA1 UA2 13H 02H DATA00 DATA01 CKS
DATA00 : USER PICTURE Gain Flag
01H
DATA01 : Gamma Gain Flag
09H
54
PLASMA MONITOR
Appendix
11. COLOR Gain Data
Function
The external control equipment changes the COLOR gain data of the display.
Transmission Data
CFH UA1 UA2 14H 03H DATA00–DATA02 CKS
DATA00 : USER PICTURE Gain Flag
01H
DATA01 : COLOR Gain Flag
04H
DATA02 : COLOR Gain
EAH : -22 | FFH : -1 00H : 0 | 16H : +22
ACK
6FH UA1 UA2 14H 02H DATA00 DATA01 CKS
DATA00 : USER PICTURE Gain Flag
01H
DATA01 : COLOR Gain Flag
04H
13. SHARPNESS Gain Data
Function
The external control equipment changes the SHARPNESS gain data of the display.
Transmission Data
CFH UA1 UA2 16H 03H DATA00–DATA02 CKS
DATA00 : USER PICTURE Gain Flag
01H
DATA01: SHARPNESS Gain Flag
06H
DATA02: SHARPNESS Gain
F0H : -16 | FFH : -1 00H : 0 | 10H : +16
ACK
6FH UA1 UA2 16H 02H DATA00 DATA01 CKS
DATA00 : USER PICTURE Gain Flag
01H
DATA01 : SHARPNESS Gain Flag
06H
15. BRIGHT Gain Data
Function
The external control equipment changes the BRIGHT gain data of the display.
Transmission Data
CFH UA1 UA2 18H 03H DATA00~DATA02 CKS
DATA00 : USER PICTURE Gain Flag
01H
DATA01 : BRIGHT Gain Flag
08H
DATA02 : BRIGHT Gain
C0H : -64 | FFH : -1 00H : 0 | 40H : +64
ACK
6FH UA1 UA2 18H 02H DATA00 DATA01 CKS
DATA00 : USER PICTURE Gain Flag
01H
DATA01 : BRIGHT Gain Flag
08H
12. TINT Gain Data
Function
The external control equipment changes the TINT gain data of the display.
Transmission Data
CFH UA1 UA2 15H 03H DATA00–DATA02CKS
DATA00: USER PICTURE Gain Flag
01H
DATA01: TINT Gain Flag
05H
DATA02: TINT Gain
EAH:-22 | FFH:-1 00H: 0 | 16H:+22
ACK
6FH UA1 UA2 15H 02H DATA00 DATA01 CKS
DATA00 : USER PICTURE Gain Flag
01H
DATA01 : TINT Gain Flag
05H
14. CONTRAST Gain Data
Function
The external control equipment changes the CONTRAST gain data of the display.
Transmission Data
CFH UA1 UA2 17H 03H DATA00~DATA02 CKS
DATA00 : USER PICTURE Gain Flag
01H
DATA01 : CONTRAST Gain Flag
07H
DATA02 : CONTRAST Gain
00H:0 | 3FH:63
ACK
6FH UA1 UA2 17H 02H DATA00 DATA01 CKS
DATA00 : USER PICTURE Gain Flag
01H
DATA01 : CONTRAST Gain Flag
07H
16. V.POSITION Gain Data
Function
The external control equipment changes the V. POSITION gain data of the display.
Transmission Data
CFH UA1 UA2 19H 03H DATA00–DATA02 CKS
DATA00 : USER POSITION Gain Flag
03H
DATA01 : V.POSITION Gain Flag
01H
DATA02 : V.POSITION Gain
C0H : -64 | FFH : -1 00H : 0 | 40H : +64
ACK
6FH UA1 UA2 19H 02H DATA00 DATA01 CKS
DATA00 : USER POSITION Gain Flag
03H
DATA01 : V.POSITION Gain Flag
01H
PLASMA MONITOR
55
Appendix
17. H.POSITION Gain Data
Function
The external control equipment changes the H. POSITION gain data of the display.
Transmission Data
CFH UA1 UA2 1AH 03H DATA00–DATA02 CKS
DATA00 : USER POSITION Gain Flag
03H
DATA01 : H.POSITION Gain Flag
02H
DATA02 : H.POSITION Gain
C0H : -64 | FFH : -1 00H : 0 | 40H : +64
ACK
6FH UA1 UA2 1AH 02H DATA00 DATA01 CKS
DATA00 : USER POSITION Gain Flag
03H
DATA01 : H.POSITION Gain Flag
02H
18. PHASE Gain Data
Function
The external control equipment changes the clock phase of the display. (This command will be received only when AUTO PICTURE is OFF.)
Transmission Data
CFH UA1 UA2 1BH 03H DATA00 DATA01 DATA02 CKS
DATA00 : USER POSITION Gain Flag
03H
DATA01: PHASE Gain Flag
03H
DATA02: PHASE Gain
00H:0 | 1FH:31
ACK
6FH UA1 UA2 1BH 02H DATA00 DATA01 CKS
DATA00 : USER POSITION Gain Flag
03H
DATA01 : PHASE Gain Flag
03H
19. CLOCK Gain Data
Function
The external control equipment changes the division ratio of the display. (This command will be received only when AUTO PICTURE is OFF.)
Transmission Data
CFH UA1 UA2 1CH 03H DATA00–DATA02 CKS
DATA00 : USER POSITION Gain Flag
03H
DATA01 : CLOCK Gain Flag
04H
DATA02 : CLOCK Gain
E0H : -32 | FFH : -1 00H : 0 | 20H : +32
ACK
6FH UA1 UA2 1CH 02H DATA00 DATA01 CKS
DATA00 : USER POSITION Gain Flag
03H
DATA01 : CLOCK Gain Flag
04H
22. V-HEIGHT Gain Data
Function
The external control equipment changes the V­HEIGHT (horizontal expansion ratio) of the dis­play. (This command will be received only when multi screen is ON.)
Transmissin Data
CFH UA1 UA2 1FH 03H DATA00–DATA02 CKS
DATA00: USER POSITION Gain Flag
09
DATA01: V-HEIGHT Gain Flag
03H
DATA02: V-HEIGHT Gain
80H : -128 | FFH : -1 0H : 0 | 7FH : +127
ACK
6FH UA1 UA2 1FH 02H DATA00 DATA01 CKS
DATA00 : USER POSITION Gain Flag
09
23. H-WIDTH Gain Data
Function
The external control equipment changes the H­WIDTH (vertical expansion ratio) of the display. (This command will be received only when multi screen is ON.)
Transmissin Data
CFH UA1 UA2 20H 03H DATA00–DATA02 CKS
DATA00 : USER POSITION Gain Flag
09
DATA01 : H-WIDTH Gain Flag
04H
DATA02 : H-WIDTH Gain
80H : -128 | FFH : -1 OH : 0 | 7FH : +127
ACK
6FH UA1 UA2 20H 02H DATA00 DATA01 CKS
DATA00 : USER POSITION Gain Flag
09
DATA01 : H-WIDTH Gain Flag
04H
24. TIMER SWITCH
Function
The external control equipment changes the timer on/off switching of the display.
Transmissin Data
CFH UA1 UA2 02H 01H DATA00 CKS
DATA00 :
0 : RESERVE OFF 1 : RESERVE ON
ACK
6FH UA1 UA2 02H 01H DATA00 CKS
DATA00 :
0 : RESERVE OFF 1 : RESERVE ON
56
PLASMA MONITOR
DATA01 : V-HEIGHT Gain Flag
03H
Appendix
25. AUTO PICTURE Select
Function
The external control equipment switches the AUTO PICTURE of the display on and off.
Transmissin Data
CFH UA1 UA2 57H 02H DATA00 DATA01 CKS
DATA00
01H : AUTO PICTURE ON 02H : AUTO PICTURE OFF
DATA01
01H : MODE 4X3 02H : MODE 16X9 03H : MODE 16X9!
ACK
6FH UA1 UA2 57H 02H DATA00 DATA01 CKS
DATA00
01H : AUTO PICTURE ON 02H : AUTO PICTURE OFF
DATA01
01H : MODE 4X3 02H : MODE 16X9 03H : MODE 16X9!
26. RESET
Function
The external control equipment resets the user adjustment items of the display.
Transmissin Data
0FH UA1 UA2 54H 01H DATA00 CKS
DATA00
00H : ALL NORMAL 01H : RASTER NORMAL 02H : VISUAL NORMAL
ACK
2FH UA1 UA2 54H 01H DATA00 CKS
DATA00
00H : ALL NORMAL 01H : RASTER NORMAL 02H : VISUAL NORMAL
*
The operation is the same as when the remote control key has been entered.
27. COLOR SYSTEM Select
Function
The external control equipment selects the color system settings of the display.
Transmission Data
CFH UA1 UA2 5CH 01H DATA00 CKS
DATA00
01H : NTSC3.58 02H : NTSC4.43 03H : PAL 04H : SECAM 96H : AUTO
ACK
6FH UA1 UA2 5CH 01H DATA00 CKS
DATA00
01H : NTSC3.58 02H : NTSC4.43 03H : PAL 04H : SECAM 96H : AUTO
28. INPUT MODE Request
Function
The display returns the current status for input mode requests of the external control equip­ment.
Transmission Data
0FH UA1 UA2 41H 00H CKS
ACK
6FH UA1 UA2 41H 01H DATA00 CKS
DATA00 : Input Select
01H : Video 02H : RGB1 03H : RGB2 04H : RGB3 05H : HD/DVD 0FH : SCART
29. SCREEN MODE Request
Function
The display returns the current status for screen mode requests of the external control equip­ment.
Transmission Data
0FH UA1 UA2 42H 00H CKS
ACK
6FH UA1 UA2 42H 01H DATA00 CKS
DATA00
02H : STADIUM 03H : ZOOM 04H : NORMAL 05H : FULL
30. VIDEO ADJ Request
Function
The display returns the current status for video adjustment information requests of the exter­nal control equipment.
Transmission Data
0FH UA1 UA2 45H 00H CKS
ACK
6FH UA1 UA2 45H 0CH DATA00–DATA0B CKS
DATA00 : RED Gain
E0H : -32 | FFH : -1 00H : 0 | 20H : +32
DATA01 : GREEN Gain
E0H : -32 | FFH : -1 00H : 0 | 20H : +32
DATA02 : BLUE Gain
E0H : -32 | FFH : -1 00H : 0 | 20H : +32
DATA03 : COLOR Gain
EAH : -22 | FFH : -1 01H : 0 | 16H : +22
DATA04: TINT Gain
EAH : -22 | FFH : -1 01H : 0 | FFH : -1 01H : 0 | 16H : +22
DATA05 : SHARPNESS Gain
F0H : -16 | FFH : -1 01H : 0 | 10H : +16
PLASMA MONITOR
57
Appendix
DATA06 : CONTRAST Gain
00H : 0 | 3FH : 63
DATA07: BRIGHT Gain
C0H : -64 | FFH : -1 00H : 0 | 40H : +64
DATA08 : RED Bias
E0H : -32 | FFH : -1 00H : 0 | 20H : +32
DATA09 : GREEN Bias
E0H : -32 | FFH : -1 00H : 0 | 20H : +32
DATA0A : BLUE Bias
E0H : -32 | FFH : -1 00H : 0 | 20H : +32
DATA0B : Gamma Gain
00H : OFF 01H : ON
NOTE: In the currently displayed mode, 00H is output when the memory area of the various items does not exist.
31. SCREEN ADJ Request
Function
The display returns the current status for screen adjustment information requests of the exter­nal control equipment.
Transmission Data
0FH UA1 UA2 47H 00H CKS
ACK
6FH UA1 UA2 47H 08H DATA00–DATA07 CKS
DATA00 : V.POSITION Gain
C0H : -64 | FFH : -1 00H : 0 | 40H : +64
DATA01 : H.POSITION Gain
C0H : -64 | FFH : -1 00H : 0 | 40H : +64
DATA02 : PHASE Gain
00H : 0 | 1FH : 31
DATA03 : CLOCK Gain
C0H : -32 | FFH : -1 00H : 0 | 20H : +32
DATA04:
00H (fixed)
DATA05:
00H (fixed)
32. COLOR SYSTEM Request
Function
The display returns the current status for color system information requests of the external control equipment.
Transmission Data
0FH UA1 UA2 4CH 00H CKS
ACK
6FH UA1 UA2 4CH 01H DATA00 CKS
DATA00
01H : NTSC3.58 02H : NTSC4.43 03H : PAL 04H : SECAM
33. FAILURE MODE Inform
Function
The display informs the external control equip­ment of the failure mode for requests of failure detection information by the external control equipment.
Transmission Data
0FH UA1 UA2 3FH 00H CKS
ACK
6FH UA1 UA2 3FH 02H DATA00 DATA01 CKS
DATA00
Bit0 (PDPmodule) Bit1 (POWER SUPPLY) Bit2 (TEMPERATURE) Bit3 (FAN) Bit4 A12V Bit5 D5V Bit6 notused Bit7 S12V
DATA01
Bit0 : D3.3V Bit1–Bit7 : 0 Fixed
0 : Fault 1 : Normal
0 : Fault 1 : Normal
58
PLASMA MONITOR
DATA06 : V-HEIGHT Gain
80H : -128 | FFH : -1 0H : 0 | 7FH : +127
DATA07 : H-WIDTH Gain
80H : -128 | FFH : -1 0H : 0 | 7FH : +127
NOTE: In the currently displayed mode, 00H is output when the memory area of the various items does not exist.
Appendix
34. SET CONDITION Inform
Function
The display informs the external control equip­ment of the sets condition information for re­quests of the sets condition information by the external control equipment.
Transmission Data
0FH UA1 UA2 40H 00H CKS
ACK
6FH UA1 UA2 40H 17H DATA00–DATA22 CKS
* Accumulated set usage time display
DATA12
Bit0 (LSB) | Bit7
DATA13
Bit0 | Bit7
DATA14
Bit0 | Bit3 (MSB)
Bit4–7 : 0 fixed * Microprocessor version display Display example VER 1.0
DATA15
Bit0(LSB)
|
Bit3 (MSB)
Bit4 (LSB)
|
Bit7 (MSB) * Current time display
1 character is expressed in 4 bits.
DATA16
Bit0
|
Bit3
Bit4
|
Bit7
The sets accumula­tive time in 5 digits is displayed with 4 bits per digit and the first digit is displayed from Bit 0 of DATA12.
Microprocessor version decimal point and first right digit
Microprocessor version first digit
Seconds 1s digit
Seconds 10s digit
DATA19
Bit0 | Bit3 Bit4 | Bit7
DATA20
Bit0 | Bit3 Bit4 | Bit7
DATA21
Bit0 | Bit3 Bit4 | Bit7
DATA22
Bit0 : 0 : Power management OFF
1 : Power management ON
Bit1 : 0 : Wireless remote control OFF
1 : Wireless remote control ON
Bit2 : 0 : Timer OFF
1 : Timer ON
Bit3–7 : 0 (fixed)
Day 1s digit
Day 10s digit
Month 1s digit
Month 10s digit
Year 1s digit
Year 10s digit
35. SIGNAL Inform
Function
The display informs the external control equip­ment of the input signal information for requests of input signal information by the external con­trol equipment.
Transmission Data
0FH UA1 UA2 3EH 00H CKS
ACK
6FH UA1 UA2 3EH 04H DATA00–DATA03 CKS
DATA00
Bit7–4: Displays the 10's digit of the hori-
zontal frequency. (0 to 9)
Bit3–0: Displays the 10's digit of the hori-
zontal frequency. (0 to 9)
DATA01
Bit7–4: Displays the decimal point and the
first right digit of the horizontal fre­quency. (0 to 9)
Bit3: Horizontal sync polarity display
0 : Negative 1 : Positive
Bit2 : Vertical sync polarity display
0 : Negativ 1 : Positive
Bit1,0: 0 (fixed)
DATA02
Bit7–4: Displays the 10's digit of the verti-
cal frequency. (0 to 9)
Bit3–0: Displays the 1's digit of the vertical
frequency. (0 to 9)
DATA03
Bit7–4: Displays the decimal point and the
first right digit of the vertical fre-
quency. (0 to 9) Bit3–0: 0 (fixed) ''00H'' is output when there is no signal.
DATA17
Bit0 | Bit3 Bit4 | Bit7
DATA18
Bit0 | Bit3 Bit4 | Bit7
Minutes 1s digit
Minutes 10s digit
Hours 1s digit
Hours 10s digit
PLASMA MONITOR
59
Appendix
36. SETTING MODE Select
Function
The external control equipment changes the settings of the various items of the display.
Transmission Data
CFH UA1 UA2 04H 02H DATA00 DATA01 CKS
DATA00
Bit0
0: POWER ON MODE OFF
(LAST MEMORY)
1: POWER ON MODE ON
Bit2 Bit1
0 0 : POWER ON MODE VIDEO 0 1 : POWER ON MODE RGB1 1 0 : POWER ON MODE RGB2,
1 1 : POWER ON MODE RGB3
Bit3
0: POWER MANAGER OFF 1: POWER MANAGER ON
Bit4
0: LUM. LIMIT OFF 1: LUM. LIMIT ON
Bit5
0: ORBITTING OFF 1: ORBITTING ON
Bit7 Bit6
0 0 : GRAY LEVEL 1 0 1 : GRAY LEVEL 2 1 0 : GRAY LEVEL 3
DATA01
Bit0 Bit1
0 0 : RGB MODE STILL 1 0 : RGB MODE MOTION 0 1 : RGB MODE DTV
Bit2 Bit3
0 0 : INV/WT OFF 1 0 : INV/WT INV 0 1 : INV/WT ALL WHITE 1 1 : not used
Bit4 Bit5 RGB3 ADJ
0 0 : 1 1 0 : 2 0 1 : 3
Bit6
0: PROG. ORBIT OFF 1: PROG. ORBIT ON
Bit7 : 0 (fixed)
DATA02
Bit 0-7: H-DOT setting
01H: 1dot | 14H: 20dot Ignore values other than the above.
DATA03
Bit 0-7: V-LINE setting
01H: 1 line | 14H: 20 line Ignore values other than the above.
(Available only when Bit0 is set to 1)
DVD/HD, SCART
DATA04
Bit 0-7: TIME setting
01H : 1 min | 05H : 5 min Ignore values other than the above.
ACK
7FH UA1 UA2 04H 05H DATA00–04 CKS
NOTE: The INV function for DATA 01 will not have last memory. It should be returned to default at time of powering ON/OFF and selecting input.
NOTE: When tha plasma monitor is turned ON or OFF, LONG LIFE MODE 3 setting is set to off and the last data is not stored in memory.
ACK
7FH UA1 UA2 04H 02H DATA00 DATA01 CKS
37. SCREEN MODE Select
Function
The external control equipment switches the screen mode of the display.
Transmission Data
CFH UA1 UA2 51H 01H DATA00 CKS
DATA00
02H : STADIUM 03H : ZOOM 04H : NORMAL 05H : FULL
ACK
6FH UA1 UA2 51H 01H DATA00 CKS
DATA00
02H : STADIUM 03H : ZOOM 04H : NORMAL 05H : FULL
38. PICTURE Mute On
Function
The external control equipment switches on PICTURE Mute of the display.
Transmission Data
8FH UA1 UA2 3CH 00H CKS
ACK
2FH UA1 UA2 3CH 00H CKS
39. PICTURE Mute Off
Function
The external control equipment switches off PICTURE Mute of the display.
Transmission Data
8FH UA1 UA2 3DH 00H CKS
ACK
2FH UA1 UA2 3DH 00H CKS
40. MULTI MODE Select
Function
The master monitor changes MULTI MODE of the slave.
Transmission Data
CFH UA1 UA2 03H 02H DATA00 DATA01 CKS
DATA00 : SCREEN DIVIDER SETTING
01H : Single mode 02H : ­03H : Multi mode 4 screens 04H : Multi mode 9 screens
DATA01 : POSITION OF DIVIDE
01H : Upper left selected (4 screens) 02H : Upper right selected (4 screens) 03H : Lower right selected (4 screens) 04H : Lower left selected (4 screens) 05H : ­06H : ­07H : Top left selected (9 screens) 08H : Top middle selected (9 screens) 09H : Top right selected (9 screens) 0AH : Middle left selected (9 screens) 0BH : Middle center selected (9 screens) 0CH : Middle right selected (9 screens) 0DH : Bottom left selected (9 screens) 0EH : Bottom middle selected (9 screens) 0FH : Bottom right selected (9 screens)
ACK
7FH UA1 UA2 03H 02H DATA00 DATA01 CKS
DATA00 (SCREEN DIVIDER SETTING)
01H: Single mode 02H: Multi-mode 2-screen 03H: Multi-mode 4-screen 04H: Multi-mode 9-screen
DATA01 (POSITION OF DIVIDE)
01H: Upper left screen selected (4 dividing) 02H: Upper right screen selected (4 dividing) 03H: Lower right screen selected (4 dividing) 04H: Lower left screen selected (4 dividing) 05H: Top screen selected (2 dividing) 06H: Bottom screen selected (2 dividing) 07H: Top left screen selected (9 dividing) 08H: Top middle screen selected (9 dividing) 09H: Top right screen selected (9 dividing) 0AH: Middle left screen selected (9 dividing) 0BH: Center screen selected (9 dividing) 0CH: Middle right screen selected (9 dividing) 0DH: Bottom left screen selected (9 dividing) 0EH: Bottom middle screen selected (9 dividing) 0FH: Bottom right screen selected (9 dividing)
NOTE: When the Multi-mode 2-screen is selected, it returns an ACK as non-support.
60
PLASMA MONITOR
Appendix
41. MULTI MODE Request
Function
The master monitor requests the status of MULTI MODE of the slave for master.
Transmission data
0FH UA1 UA2 3BH 00H CKS
ACK
6FH UA1 UA2 3BH 02H DATA–02 CKS
DATA00 : SCREEN DIVIDER SETTING
01H : Single mode 02H : ­03H : Multi mode 4 screens 04H : Multi mode 9 screens
DATA01 : POSITION OF DIVIDE
NOTE: When DATA00 is 01H, this data is invalid.
01H : Upper left selected (4 screens) 02H : Upper right selected (4 screens) 03H : Lower right selected (4 screens) 04H : Lower left selected (4 screens) 05H : ­06H : ­07H : Top left selected (9 screens) 08H : Top middle selected (9 screens) 09H : Top right selected (9 screens) 0AH : Middle left selected (9 screens) 0BH : Middle center selected (9 screens) 0CH : Middle right selected (9 screens) 0DH : Bottom left selected (9 screens) 0EH : Bottom middle selected (9 screens) 0FH : Bottom right selected (9 screens)
42. OSM Select
Function
The external equipment switches the on-screen menu (OSM) of the display unit ON and OFF.
Transmission Data
DFH 80H 60H 58H 01H DATA00 CKS
DATA00
01H : OSM ON (During normal operation) 02H : OSM OFF
ACK
7FH 60H 80H 58H 01H DATA00 CKS
DATA00
01H : OSM ON 02H : OSM OFF
* Use this command with the setting of bits 0
and 1 fixed as follows: bit 0 = 1, and bit 1 = 1.
* ACK should be ignored in the case of a cas-
cade connection.
43. VOLUME Gain Data
Function
The master monitor changes the volume gain data of the slave.
Transmission data
CFH UA1 UA2 21H 03H DATA00–02 CKS
DATA00 : VOLUME Gain
00H : 0 | 18H : 24
DATA01 : BALANCE Gain
E8H : -24 | 00H : 0 | 18H : +24
DATA02 : MUTE
00H : OFF 01H : ON
ACK
6FH UA1 UA2 21H 03H DATA00–02 CKS
DATA00 : VOLUME Gain DATA01 : BALANCE Gain DATA02 : MUTE
44. SOUND INPUT Select
Function
The master monitor changes the audio input of the slave.
Transmission data
CFH UA1 UA2 05H 02H DATA00–01 CKS
DATA00 : INPUT1
00H : VIDEO 01H : RGB1 02H : RGB2, DVD/HD, SCART 03H : RGB3
DATA01 : INPUT2
00H : VIDEO 01H : RGB1 02H : RGB2, DVD/HD, SCART 03H : RGB3
ACK
6FH UA1 UA2 05H 02H DATA00–01 CKS
DATA00 : INPUT1 DATA01 : INPUT2
45. VOLUME Gain Data Request
Function
The master monitor changes the VOLUME gain data of the slave.
Transmission data
0FH UA1 UA2 46H 00H CKS
ACK
DATA00 : VOLUME Gain
00H : 0 | 18H : 24
DATA01 : BALANCE Gain
E8H : -24 | 00H : 0 | 18H : +24
DATA02 : MUTE
00H : OFF 01H : ON
46. SOUND INPUT SELECT Request
Function
The master monitor requests the status of the audio input of the slave.
Transmission data
0FH UA1 UA2 60H 00H CKS
ACK
6FH UA1 UA2 60H 02H DATA00–01 CKS
DATA00 : INPUT1
00H : VIDEO 01H : RGB1 02H : RGB2, DVD/HD, SCART 03H : RGB3
DATA01 : INPUT2
00H : VIDEO 01H : RGB1 02H : RGB2, DVD/HD, SCART 03H : RGB3
PLASMA MONITOR
61
Appendix
47. CONFIG MENU Select
Function
The master monitor selects the CONFIG set­tings of the slave.
Transmission data
CFH UA1 UA2 06H 01H DATA00 CKS
DATA00
Bit0 Bit1 : OSD DISPLAY
0 0 : BASIC 1 0 KEY 0 1 OFF 0 0 disabled
Bit2
0 : OSD MODE BASIC 1 : OSD MODE PRO
Bit3 Bit4 : SYNC CONTROL
0 0 AUTO 1 0 GSYNC 0 1 CSYNC
Bit5
0 : PLE LINK OFF 1 : PLE LINK ON
Bit6,7
0 (fixed)
ACK
6FH UA1 UA2 06H 01H DATA00 CKS
48. TIMER PROGRAM Setting
Function
The master sets timer program of the slave.
Transmission data
CFH UA1 UA2 08H 0CH DATA00 – DATA11 CKS
DATA00 Program No.
01H – 07H: Nos. 1 – 7
DATA01 Date (Month) Setting
01H – 09H: 1 – 9 10H – 12H: 10 – 12 AAH: When the date (day) is set to “Every­day” or “Every Sun. - every Sat.”. FFH: - (No setting)
DATA02 Date (Day) Setting
00H: Everyday 01H – 09H: 1- 9 10H – 19H: 10 – 19 20H – 29H: 20 – 29 30H – 31H: 30 – 31 40H – 46H: Every Sun. – every Sat. FFH: - (No setting)
DATA03 ON Time (HOUR)
00H: 00 - 09 10H – 19H: 10 – 19 20H – 23H: 20 – 23 FFH: - (No setting)
DATA04 ON Time (MIN)
00H – 09H: 00- 09 10H – 19H: 10 – 19 20H – 29H: 20 – 29 30H – 39H: 30 – 39 40H – 49H: 40 – 49 50H – 59H: 50 – 59 FFH: - (No setting)
DATA05 OFF Time (HOUR)
00H – 09H: 00 - 09 10H – 19H: 10 – 19 20H – 23H: 20 – 23 FFH: - (No setting)
DATA06 OFF Time (MIN)
00H – 09H: 00- 09 10H – 19H: 10 – 19 20H – 29H: 20 – 29 30H – 39H: 30 – 39 40H – 49H: 40 – 49 50H – 59H: 50 – 59 FFH: - (No setting)
DATA07 Mode
00H:VIDEO 01H:RGB1 02H:RGB2/HD/SCART 03H:RGB3 04H:INV 05H:WT 06H:RP 07H:RI FFH: - (No setting)
DATA08 Repeat Program MODE1
00H:VIDEO 01H:RGB1 02H:RGB2/HD/SCART 03H:RGB3 04H:INV 05H:WT FFH: - (No setting)
DATA09 Repeat Program TIME1
00H: 1 min 01H: 2 min 02H: 3 min 03H: 4 min 04H: 5 min 05H: 7 min 06H: 10 min 07H: 15 min 08H: 30 min
DATA10 Repeat Program MODE2
00H:VIDEO 01H:RGB1 02H:RGB2/HD/SCART 03H:RGB3 04H:INV 05H:WT FFH: - (No setting)
DATA11 Repeat Program TIME2
00H: 1 min 01H: 2 min 02H: 3 min 03H: 4 min 04H: 5 min 05H: 7 min 06H: 10 min 07H: 15 min 08H: 30 min
ACK
6FH UA1 UA2 08H 00H CKS
49. MULTI DISP MODE Select
Function
The master switches DISP MODE of the slave.
Transmission data
CFH UA1 UA2 07H 02H DATA00 DATA01 CKS
DATA00 (DISP MODE)
BIT0 0: SPLIT
1: BLANKING
The other bits shall be fixed at 0.
DATA01 (Spare): DONT CARE
ACK
6FH UA1 UA2 07H 02H DATA00 DATA01 CKS
DATA00 (DISP MODE) BIT0 0: SPLIT
1: BLANKING The other bits shall be fixed at 0. DATA01 (Spare): DONT CARE
50. MULTI DISP MODE Request
Function
The master requests the DISP MODE settings of the slave.
Transmission data
CFH UA1 UA2 61H 02H DATA00 DATA01 CKS
DATA00 (DISP MODE)
BIT0 0: SPLIT
1: BLANKING The other bits shall be fixed at 0. DATA01 (Spare): DONT CARE
62
PLASMA MONITOR
51. PRESENT TIME Setting
Function
The master monitor sets a present time of the slave monitor.
Transmission data
CFH UA1 UA2 09H 0AH DATA00 – DATA09 CKS
DATA00 First two digits of year
19H: indicates 1900s 20H: indicates 2000s
DATA01 Last two digits of year
00H – 09H: 00 – 09 10H – 19H: 10 – 19 20H – 29H: 20 – 29 30H – 39H: 30 – 39 40H – 49H: 40 – 49 50H – 59H: 50 – 59 60H – 69H: 60 – 69 70H – 79H: 70 – 79 80H – 80H: 80 – 89 90H – 99H: 90 – 99
DATA02 Month
01H – 09H: 1 – 9 10H – 12H: 10 – 12
Appendix
DATA03 Day
01H – 09H: 1 – 9 10H – 19H: 10 – 19 20H – 29H: 20 – 29 30H – 30H: 30 – 31
DATA04 Hour
00H – 09H: 00 – 09 10H – 19H: 10 – 19 20H – 23H: 20 – 23
DATA05 Minute
00H – 09H: 00 – 09 10H – 19H: 10 – 19 20H – 29H: 20 – 29 30H – 39H: 30 – 39 40H – 49H: 40 – 49 50H – 59H: 50 – 59
ACK
6FH UA1 UA2 09H 00H CKS
PLASMA MONITOR
63
Appendix
Pin Configuration and Signal of the RGB 3 IN Connector (DVI Connector)
3
121 910
11
171819 20
RGB3
56
4
12
14 15
13
22
21
Pin No. Signal (Digital)
8
7
16 24
23
1 T.M.D.S Data 2 ­2 T.M.D.S Data 2 + 3 T.M.D.S Data 2 Shield 4 No connection 5 No connection 6 DDC Clock 7 DDC Data 8 No connection
9 T.M.D.S Data 1 ­10 T.M.D.S Data 1 + 11 T.M.D.S Data 1 Shield 12 No connection 13 No connection 14 +5V Power 15 Ground 16 Hot Plug Detect 17 T.M.D.S Data 0 ­18 T.M.D.S Data 0 + 19 T.M.D.S Data 0 Shield 20 No connection 21 No connection 22 T.M.D.S Clock Shield 23 T.M.D.S Clock + 24 T.M.D.S Clock ­25 No connection 26 No connection 27 No connection 28 No connection 29 No connection
64
PLASMA MONITOR
Signal Identification For Raster Preset
Appendix
(horizontal frequency/vertical frequency)
Resolution
VIDEO NTSC*1
VIDEO PAL*1 VIDEO SECAM*1
640 X 240 (15.734kHz/59.94Hz)
768 X 288 (15.557kHz/50.39Hz)
640 X 480 (31.469kHz/59.94Hz)
640 X 480 (35kHz/66.667Hz)
640 X 480 (37.861kHz/72.809Hz)
640 X 480 (37.5kHz/75Hz)
640 X 480 (43.269kHz/85.008Hz)
640 X 480 (39.375kHz/75Hz)
800 X 600 (35.156kHz/56.25Hz)
800 X 600 (37.879kHz/60.31Hz)
800 X 600 (48.077kHz/72.188Hz)
800 X 600 (46.875kHz/75Hz)
800 X 600 (53.674kHz/85.061Hz)
832 X 624 (49.725kHz/74.55Hz)
852 X 480 (31.722kHz/59.966Hz)
848 X 480 (31.02kHz/60Hz)
1024 X 768 (56.476kHz/70.069Hz)
1024 X 768 (60.023kHz/75.029Hz)
1024 X 768 (68.677kHz/84.997Hz)
1024 X 768 (60.24kHz/74.93Hz)
768 X 576 (31.389kHz/50Hz)
640 X 480 (31.47kHz/59.9Hz)
ISS-6010 NTSC*2
ISS-6010 PAL*2
VESA 480@60Hz
MAC @13''*5
VESA 480@72Hz*3
VESA 480@75Hz
VESA 480@85Hz*3
XGA-2 480@75Hz*3
VESA 600@56Hz
VESA 600@60Hz
VESA 600@72Hz*3
VESA 600@75Hz*3
VESA 600@85Hz*3
MAC @16''*3*5
I-O data wide*4
VGA WIDE (NEC1)
VESA 768@70Hz*3
VESA 768@75Hz*3
VESA 768@85Hz*3
MAC @19''*3*5
IDC-3000G PAL625P
IDC-3000G NTSC 525P
Factory
settings
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
User
settings
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
Sync polarity
-
-
NEG
NEG
NEG
-
NEG
NEG
POS
NEG
POS
POS
POS
POS
POS
-
NEG
POS
NEG
POS
POS
-
NEG
NEG
Presence/absence of sync
VerHor
-
-
NEG
NEG
NEG
NEG
NEG
POS
NEG
POS
POS
POS
POS
POS
NEG
POS
NEG
POS
POS
NEG
NEG
YES
YES
YES
-
-
-
-
YES
YES
YES
YES
YES
YES
YES
YES
YES
-
YES
YES
YES
YES
YES
-
YES
YES
VerHor
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
RGB
MODE
STILL
-
-
-
MOTION
INPUT
MODE*7
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
4 X 3
-
4 X 3
-
-
-
-
4 X 3
4 X 3
4 X 3
-
-
-
-
16 X 9!
16 X 9
-
-
-
-
-
4 X 3
*1 Convert to 640 dots x 480 lines and display. *2 These signals cannot be displayed in the RGB3 input mode. *3 The picture will be shaky when the moving images of video games, etc., are input. (In this case set the refresh rate to 60 kHz or less.) *4 Only when using an I-O DATA graphic accelerator board. *5 Use a separately sold signal adapter (mini D-Sub 15-pin) when connecting to a Macintosh computer.
For some models, make the mini D-Sub 15-pin connection using the included RGB signal cable. These signals are Sync On Green.
*6 Make the settings to display these signals. The signals will not be displayed properly unless the correct settings are made.
NOTE:
* Input of a VGA or W-VGA signal is recommended because the display resolution is 853 x 480 pixels.
For other cases, conversion is made to 640 dots x 480 lines or 853 dots x 480 lines. * 852 dot by 480 line signals are displayed with this resolution. * 848 dot by 480 line signals are displayed at a resolution of 848 dots by 480 lines when "NORMAL" is selected, and converted to 853 dots by 480 lines when "FULL"
is selected. * At the time of video input, video signals derived from poor recording conditions may create poor images. * The sync may be disturbed when non-standard signals other than the aforementioned are input. * Multiple screens (2 screens) can only display signals having an aspect ratio of 4:3. *3 Cannot be used with multiple screens. * With digital inputs some signals are not accepted.
* IBM PC/AT is a registered trademark of International Business Machines Corporation. * Macintosh is a registered trademark of Apple Computer, Inc. * VESA is a trademark of Video Electronics Standard Association. * DVI is an abbreviation for Digital Visual Interface.
PLASMA MONITOR
65
Appendix
Specifications
PlasmaSync 42PD3 (Model PX-42VP3A)
Plasma Screen 42 inch Visual size (Diagonal), AC Drive type
Aspect ratio : 16:9 Optical filter coating Display color : 16,770,000 colors 256 levels
RGB Input Terminals RGB 1 : mini D-SUB 15pin
RGB 2 : BNC (R,G,B, H/CS, V) * Sync-on-Green compatible. RGB 3 : Digital RGB (DVI 24+5pin: Not compatible with analog input.
Complies with DVI
R/G/B Video : Analog 0.7Vp-p/75 Ohms (Positive)
Sync. : Separate Sync. TTL level, 0.7 - 4.0Vp-p/75 Ohms..........BNC only
Horizontal Sync. (Positive/Negative) Vertical Sync. (Positive/Negative) Composite Sync. TTL Level (Positive/Negative) Composite Sync. On Green Video 0.3Vp-p (Negative)
RGB Output Terminals BNC (R,G,B, H/CS, V)
THROUGH OUT
DVD/HD Input/Output Terminal BNC (Y,Cb/Pb,Cr/Pr) DVD/HD IN / THROUGH OUT Serves as RGB2 input/output
Video Input/Output Terminals 1.0Vp-p, 75 Ohms unbalanced (BNC-Jack), Composite video signal, Sync-negative.
VIDEO IN / THROUGH OUT Y : 1.0Vp-p, 75 Ohms unbalanced, Sync-negative. S-VIDEO IN / THROUGH OUT C : 0.28Vp-p, 75 Ohms unbalanced, Color burst level.
Audio Input/Output Terminals AUDIO IN : Stereo RCA X 2
AUDIO OUT : Stereo RCA X 1
External Control mini D-SUB 9 pin (IN/THROUGH OUT)
(IN/THROUGH OUT) RS-232C Control
Synchronization Range Horizontal : 15.5 to 68.7 KHz (automatic : step scan)
Vertical : 46.0 to 85.0 Hz (automatic : step scan) Maximum Resolution RGB : 853(H) X 480(V) pixels Power Supply 100-120 VAC, 50/60 Hz Current Rating 5.0A (maximum) Power consumption 295W (typical) / 425W (MAX) Dimensions 39.3(W) x 23.4(H) x 4.5(D) inches / 998(W) X 595(H) X114(D) mm Weight 64 lbs / 29 kg Environmental Considerations Operating Temperature : 0˚C to 40˚C
Humidity : 20 to 80%
Storage Temperature : -10˚C to 50˚C
Humidity : 10 to 90%
Regulations : UL/C-ULApproved (UL 1950/CSA 950)
DOC Canada requirements
Meets FCC class A requirements
All specifications are subject to change without notice.
66
PLASMA MONITOR
Appendix
Troubleshooting
If the picture quality is poor or there is some other problem, check the adjustments, operations, etc., before requesting service.
Symptom Checks Remedy
Mechanical sound is heard
Maybe the sound from the cooling fans used to prevent over heating.
Picture is disturbed. Sound is noisy. Remote control unit operates erroneously.
Monitors power does not turn on when the remote control’s power button is pressed.
Monitor does not operate when the remote controls buttons are pressed.
No Sound or Picture is produced.
Is a connected component set directly in front or at the side of the display?
Is the monitors power cord plugged into a power outlet?
Are all the monitors indicators off?
Has an ID number been set for the main unit?
Are the remote controls batteries worn out?
Is the remote control pointed at the monitor,
or is there an obstacle between the remote control and the monitor?
Is direct sunlight or strong artificial light shin­ing on the monitors remote control sensor?
You are not within the effective operating range.(Wireless)
Has an ID number been set for the main unit?
Are the remote control's batteries worn out?
The front panel buttons of the main unit do
not function
Is the monitor's power cord plugged into a power outlet?
Power outlet inactive. Power of external equipment is not ON. External equipment has been incorrecty con­nected. Incorrect input selection.
Is the volume set at the minimum?
Leave some space between the display and the
connected components.
Plug the monitors power cord into a power out­let.
Plug the monitors power cord into a power out­let.
Set an ID number with the ID SELECT button, or set the ID number to ALL.
Replace both batteries with new ones.
Point the remote control at the monitors remote
control sensor when pressing buttons, or remove the obstacle.
Eliminate the light by closing curtains, pointing the light in a different direction, etc.
Use the remote control within 30º left and right of center (at a diatance of 22ft).
Set an ID number with the ID SELECT button, or set the ID number to ALL.
Replace both batteries with new ones.
The front panel buttons do not function during
Control Lock
Plug the monitor's power cord into a power out­let.
Be sure wall switch is on and outlet has power. Switch to ON or connect to an active AC outlet. Correct all connections. Press correct RGB1, RGB2/DVD/HD, RGB3, or VIDEO button.
Increase the volume on the sound menu.
Picture appears but no sound is produced.
Poor picture with VIDEO signal input.
Poor picture with RGB signal input.
Tint is poor or colors are weak.
Nothing appears on screen.
Part of picture is cut off or picture is not centered.
Image is too large or too small.
Is the mute mode set on?
Are the amplifier, speakers properly con-
nected?
Is AUDIO INPUT set correctly?
Improper control setting.
Local interference. Cable interconnections. Input impedance is not correct level.
Improper control setting. Incorrect 15 PIN connector pin connections.
Are the tint and colors properly adjusted?
Is the computer's power turned on?
Is a source connected?
Is the power manager function in the standby
or off mode?
Is the position adjustment appropriate?
Is the screen size adjustment appropriate?
Set MUTE OFF on the SOUND menu.
Connect the amplifier, speakers properly.
Set INPUT on the SOUND menu correctly.
Adjust picture controls as needed.
Try another location for the monitor. Be sure all connections are secure.
Adjust picture controls as needed. Check pin assignments and connections.
Adjust the tint and color.
Turn on the computer's power.
Connect source to the monitor.
Operate the computer (move the mouse. etc.)
Adjust the AUTO PICTURE properly.
Make the adjustment with the wide screen set-
ting.
PLASMA MONITOR
67
Appendix
Symptom Checks
Picture is unstable.
POWER/STANDBY indicator is lighted in orange or yellow.
POWER/STANDBY indicator is blinking in green.
*1 In the following case, power off the monitor immediately and contact your dealer or authorized NEC Service Center. The monitor turns off in 5 seconds after powering on and then the POWER/STANDBY indicater blinks. It indicates that the power supply circuit(flashing red), one or more fans(flashing yellow) have been damaged.
*2 Overheat protector If the monitor becomes too hot, the overheat protector will be activated and the monitor will be turned off. If this happens., turn off the power to the monitor and unplug the power cord. If the room where the monitor is installed is particularly hot, move monitor to a cooler location, and wait for the monitor to cool for 60 minutes. If the problem persists, contact your NEC dealer for service.
Is the computer's resolution setting appropri­ate?
Horizontal and/or vertical sync signal is not present when the Intelligent Power Manager control is on.
POWER/STANDBY indicatoris flashing red or yellow.
The temperature inside the main unit has be­come too high and has activated the protec­tor.
Set to the proper resolution.
Check the input signal.
The unit is OFF in the timer operation; this is
not a malfunction. See *1.
Promptly switch off the power of the main unit and wait until the internal temperature drops. See *2.
Remedy
68
PLASMA MONITOR
Cabinet dimensions
PlasmaSync 42PD3 (Model PX-42VP3A)
39.3''(998)
Appendix
4.5''
(114)
4.4''
(112)
1.4''(35.8)
23.4''(595)
17''(432)
19.85''(504.08)
1.4''(35.8)
Unit : inch (mm)
PLASMA MONITOR
69
NEC Technologies, Inc.
1250 N. Arlington Heights Road, Suite 500
Itasca, Illinois 60143-1248
Printed in Japan
7S800461
Loading...