Nec PLASMASYNC PX-42VM1A user Manual

PlasmaSync Plasma Monitor

User’s Manual

NEC Technologies

Important Information

Precautions

Please read this manual carefully before using your NEC plasma monitor and keep the manual handy for future reference.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION:

TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO DO NOT USE THIS UNIT'S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS, UNLESS THE PRONGS CAN BE FULLY INSERTED. REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH-VOLTAGE COMPONENTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

WARNING

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This symbol warns the user that uninsulated voltage within the unit may have sufficient magnitude to cause electric shock. Therefore, it is dangerous to make any kind of contact with any part inside of this unit.

This symbol alerts the user that important literature concerning the operation and maintenance of this unit has been included. Therefore, it should be read carefully in order to avoid any problems.

WARNING

Warnings and Safety Precaution

The NEC plasma monitor is designed and manufactured to provide long, trouble-free service. No maintenance other than cleaning is required. Use a soft dry cloth to clean the panel. Never use solvents such as alcohol or thinner to clean the panel surface. The plasma display panel consists of fine picture elements (cells). Although NEC produces the plasma display panels with more than 99.99 percent active cells, there may be some cells that do not produce light or remain lit. For operating safety and to avoid damage to the unit, read carefully and observe the following instructions. To avoid shock and fire hazards:

1. Provide adequate space for ventilation to avoid internal heat build-up. Do not cover rear vents or install in a closed cabinet or shelves. The unit is equipped with cooling fans. If you install the unit in an enclosure, be sure there is adequate space at the top of the unit to allow hot air to rise and escape. If the monitor becomes too hot, the overheat protector will be activated and the monitor will be turned off. If this happens, turn off the power to the monitor and unplug the power cord. If the room where the monitor is installed is particularly hot, move the monitor to a cooler location, and wait for the monitor to cool for 60 minutes. If the problem persists, contact your NEC dealer for service.

2. Do not use the power cord polarized plug with extension cords or outlets unless the prongs can be completely inserted.

3. Do not expose unit to water or moisture.

4. Avoid damage to the power cord, and do not attempt to modify the power cord.

5. Unplug unit during electrical storms or if unit will not be used over a long period.

6. Do not open the cabinet which has potentially dangerous high voltage components inside. If the unit is damaged in this way the warranty will be void. Moreover, there is a serious risk of electric shock.

7. Do not attempt to service or repair the unit. NEC is not liable for any bodily harm or damage caused if unqualified persons attempt service or open the back cover. Refer all service to authorized NEC Service Centers.

NOTE: When you connect a computer to this monitor, attach the supplied ferrite cores. If you do not do this, this monitor will not comform to mandatory FCC standards. Attaching the ferrite cores. Set the ferrite cores on the both ends of the DVI cable (not supplied), and the one end of the power cable (supplied). Close the lid tightly until the clamps click. Use the band to secure the ferrite core (supplied).

DVI cable (not supplied)

band

core (small)

band

Connector

core (small)

Recommendations to avoid or minimize phosphor burn-in

Like all phosphor-based display devices and all other gas plasma displays, plasma monitors can be susceptible to phosphor burn under certain circumstances. Certain operating conditions, such as the continuous display of a static image over a prolonged period of time, can result in phosphor burn if proper precautions are not taken. To protect your investment in this NEC plasma monitor, please adhere to the following guidelines and recommendations for minimizing the occurrence of image burn:

*Always enable and use your computer's screen saver

function during use with a computer input source. * Display a moving image whenever possible. *Always power down the monitor when you are finished

using it.

Power cable (supplied)

core (large)

band

(Plasma Monitor side)

Set side

To avoid damage and prolong operating life:

1. Use only with 120V 50/60Hz AC power supply. Continued operation at line voltages greater than 120 Volts AC will shorten the life of the unit, and might even cause a fire hazard.

2. Handle the unit carefully when installing it and do not drop.

3. Locate set away from heat, excessive dust, and direct sunlight.

4. Protect the inside of the unit from liquids and small metal objects. In case of accident, unplug the unit and have it serviced by an authorized NEC Service Center.

5. Do not hit or scratch the panel surface as this causes flaws on the surface of the screen.

6. For correct installation and mounting it is strongly recommended to use a trained,authorized NEC dealer.

7. As is the case with any phosphor-based display (like a CRT monitor, for example) light output will gradually decrease over the life of a Plasma Display Panel.

If the plasma monitor is in long term use or continuous operation take the following measures to reduce the likelihood of phosphor burn:

* Lower the Brightness and Contrast levels as much as

possible without impairing image readability.

* Display an image with many colors and color gradations

(ie. photographic or photo-realistic images).

* Create image content with minimal contrast between light

and dark areas, for example white characters on black backgrounds. Use complementary or pastel color whenever possible.

*Avoid displaying images with few colors and distinct,

sharply defined borders between colors.

Contact NEC Technologies at 1-800-836-0655 for other recommended procedures that will best suit your particular application needs.

Précautions

Veuillez lire ce manuel avec attention avant d'utiliser votre moniteur PlasmaSync NEC et conserver ce manuel à portée de la main pour une consultation ultérieure.

ATTENTION

RISQUE D’ELECTROCUTION

NE PAS OUVRIR

MISE EN GARDE: AFIN DE REDUIRE LES RISQUES D’ELECTRO-

CUTION, NE PAS DEPOSER LE COUVERCLE, IL N’Y A AUCUNE PIECE UTILISABLE A L’INTERIEUR DE CET APPAREIL. NE CONFIER LES TRAVAUX D’ENTRETIEN QU’A UN PERSONNEL QUALIFIE.

Ce symbole a pour but de prévenir l’utilisateur de la présence d’une tension dangereuse, non isolée se trouvant à l’intérieur de l’appareil. Elle est d’une intensité suffisante pour constituer un risque d’électrocution. Eviter le contact avec les pièces à l’intérieur de cet appareil.

Ce symbole a pour but de prévenir l’utilisateur de la présence d’importantes instructions concernant l’entretien et le fonctionnement de cet appareil. Par conséquent, elles doivent être lues attentivement afin d’éviter des problèmes.

AVERTISSEMENT

AFIN DE REDUIRE LES RISQUES D’INCENDIE OU D’ELECTROCUTION, NE PAS EXPOSER CET APPAREIL A LA PLUIE OU A L’HUMIDITE. AUSSI, NE PAS UTILISER LA FICHE POLARISEE AVEC UN PROLONGATEUR OU UNE AUTRE PRISE DE COURANT SAUF SI CES LAMES PEUVENT ETRE INSEREES A FOND. NE PAS OUVRIR LE COFFRET, DES COMPOSANTS HAUTE TENSION SE TROUVENT A L’INTERIEUR. LAISSER A UN PERSONNEL QUALIFIE LE SOIN DE REPARER CET APPAREIL.

DOC avis de conformation

Cet appareil numérigue de la classe A respecte toutes les exigences du Réglement sur le Matériel Brouilleur du Canada.

Mises en garde et précautions de sécurité

Le moniteur PlasmaSync NEC a été conçu et fabriqué pour une utilisation fiable et durable. Il ne nécessite aucun entretien en dehors du nettoyage. Utiliser un chiffon doux et sec pour nettoyer la surface de l'écran. Ne jamais utiliser de solvant comme l'alcool ou le diluant. Le panneau à affichage plasma est constitué de fines particules d'images ou pixels (cellules). Bien que NEC produise des panneaux à affichage plasma avec plus de 99,99 % de cellules actives, il peut y avoir des cellules qui ne produisent pas de lumière ou qui restent allumées. Pour des raisons de sécurité et pour éviter d'endommager l'appareil, lire attentivement les instructions suivantes. Pour éviter les risques d'éléctrocution et d'incendie:

1. Laisser suffisament d'espace autour de l'appareil pour la ventilation et éviter toute augmentation excessive de la température interne. Ne pas couvrir les évents ou l'installer dans un endroit trop exigu. L'appareil est équipé de ventilateurs de refroidissement. Si vous installez l'appareil dans un espace clos, assurezvous qu'il y ait suffisamment d'espace au dessus pour permettre à l'air chaud de s'élever et de s'évacuer. Si la température du moniteur devient excessive, la protection contre les surchauffes entrera en action et coupera l'alimentation. Dans ce cas, éteindre l'appareil et débrancher le câble d'alimentation. Si la température de la pièce dans laquelle le moniteur est installé est particulièrement excessive, déplacer l'appareil dans un endroit plus frais et le laisser refroidir 60 minutes. Si le problème persiste, prendre contact avec le revendeur NEC pour le service après-vente.

2. Ne pas utiliser la fiche polarisée du cordon d’alimentation avec des prolongateurs ou des prises de courant, sauf si les lames peuvent être insérées à fond.

3. Ne pas exposer à L'eau ou à l’humidité.

4. Eviter d’endommager le cordon d’alimentation, et ne pas modifier le cordon d’alimentation.

5. Débrancher l’appareil pendant les tempêtes ou si l’appareil n’est pas utilisé pendant une longue période.

6. Ne pas ouvrir le coffret. Des composants de haute tension se trouvent à l’intérieur. Si l’appareil est endommagé de cette manière, la garantie devient caduque. De plus, il y a risque d’électrocution.

7. Ne pas essayer de réparer ou entretenir l’appareil soimême. NEC ne saura être tenu pour responsable pour toute blessure ou dommage causé par des personnes non qualifiées qui essayent de réparer ou d’ouvrir le couvercle arrière. Confier toute réparation à un centre de service agréé NEC.

REMARQUE: Lorsque vous branchez un micro-ordinateur sur ce moniteur, fixez les noyaux en ferrites fournis. Si vous ne le faîtes, le moniteur ne sera pas en conformité avec les exigences des standards FCC. Fixation des noyaux en ferrite. Installez les noyaux en ferrite sur chaque bout du câble DVI (non fourni), ainsi que sur un côté du câble d'alimentation électrique (founi). Fermez doucement le couvercle jusqu'à ce que les crans se clipsent. Utiliser les colliers pour fixer la tore en ferrite (fourni)

Câble DVI (non fourni)

Collier Collier

noyau (petit)

Câble d'alimentation électrique (fourni)

noyau (petit)

noyau (large)

Côté de l'appareil (côté du moniteur à plasma)

Connecteur

Collier

Pour éviter des dommages et prolonger la durée de service de l’appareil:

1. N’utiliser qu’une source d’alimentation de 120 V 50/ 60 Hz CA. Le fait d’utiliser l’appareil en continu à des tensions de ligne supérieures à 120 Volts CA réduit sa durée de vie et risque de provoquer un incendie.

2. Manipuler l’appareil avec soin pendant son déplacement et ne pas le faire tomber.

3. Eloigner l’appareil des endroits chauds, très poussiéreux et exposés en plein soleil.

4. Eviter que des liquides et des petits objets métalliques pénètrent à l’intérieur de l’appareil. En cas d’accident, débrancher l’appareil et le confier à un centre de service agréé NEC.

5. Ne pas frapper ou rayer la surface de la écran plasma, car des défauts risquent de se produire sur la surface de la écran plasma.

6. Pour effectuer une installation et un montage corrects, il est recommandé de faire appel au concessionnaire NEC autorisé et spécialisé.

7. Comme c'est le cas pour tout affichage à base de phosphore (comme un moniteur CRT, par exemple), la puissance de lumière baisse graduellement au cours de la vie du Panneau d'Affichage à Plasma.

Pour éviter le risque de combustion au phosphore, les mesures suivantes sont recommandées :

Comme tous les appareils d'affichage à base de phosphore et tous les autres affichages à gaz plasma, les moniteurs Plasmasync peuvent être sujets à la combustion au phosphore dans certaines circonsatnces. Certaines conditions d'utilisation, telles que l'affichage continu d'une image statique pour une durée prolongée, peuvent causer des brûlures au phophore si aucune précaution n'est prise. Pour protéger votre investissement dans ce moniteur PlasmaSync NEC, veuillez suivre les directives et les recommandations suivantes pour minimiser l'occurence de brûlure d'image :

• Assurez-vous de mettre en marche et d'utliser l'économisateur d'écran chaque fois que c'est possible lorsque vous l'utilisez avec une source d'entrée d'ordinateur.

•Affichez une image en mouvement aussi souvent que possible.

• Coupez toujours l'alimentation lorsque vous avez terminé d'utiliser la moniteur.

Si le moniteur est en usage continu ou longue durée, prenez les mesures suivantes afin d'éviter l'occurence de combustion au phosphore :

• Abaissez le niveau de l'image (contraste, luminosité) autant que possible, sans faire perdre la lisibilité de l'image.

•Affichez une image avec de nombreuses couleurs et graduations de couleur (par ex. des images photographiques ou photo-réalistes).

• Créez un contenu d'image avec un contraste minimal entre les zones sombres et les zones claires, par exemple, des caractères blancs sur un fond noir. Utilisez des couleurs complémentaires ou pastels le plus souvent possible.

• Évitez d'afficher des images avec peu de couleurs et des limites nettes et clairement définies entre les couleurs.

Contactez NEC Technologies au 1-800-836-0655 pour d'autres procédures recommandées qui conviendront le mieux au besoin de votre appareil.

Limited Warranty Plasma Monitors

NEC Technologies, Inc. (hereinafter NECTECH) warrants this product to be free from defects in material and workmanship under the following terms and, subject to the conditions set forth below, agrees to repair or replace (at NECTECH's sole option) any part of the enclosed unit which proves defective. Replacement parts or products may be new or refurbished and will meet specifications of the original parts or product.

HOW LONG IS THE WARRANTY?

Parts and labor are warranted for (1) One Year from the date of the first customer purchase.

WHO IS PROTECTED?

This warranty may be enforced only by the first purchaser.

WHAT IS COVERED AND WHAT IS NOT COVERED

Except as specified below, this warranty covers all defects in material or workmanship in this product. The following are not covered by the warranty:

1. Any product which is not distributed in the U.S.A. or Canada and Mexico by NECTECH or which is not purchased in the U.S.A. or Canada or Mexico from an authorized NECTECH dealer.

2. Any product on which the serial number has been defaced, modified or removed.

3. Damage, deterioration or malfunction resulting from: a. Accident, misuse, abuse, neglect, fire, water, light-

ning or other acts of nature, unauthorized product modification, or failure to follow instructions supplied with the product.

b.Repair or attempted repair by anyone not authorized

by NECTECH.

c. Any shipment of the product (claims must be pre-

sented to the carrier). d.Removal or installation of the product. e. Any other cause which does not relate to a product

defect. f. Burns or residual images upon the phosphor of the

panel.

4. Cartons, carrying cases, batteries, external cabinets, magnetic tapes, or any accessories used in connection with the product.

5. Service outside of the U.S.A. and Canada.

HOW YOU CAN GET WARRANTY SERVICE

1. To obtain service on your product, consult the dealer from whom you purchased the product.

2. Whenever warranty service is required, the original dated invoice (or a copy) must be presented as proof of warranty coverage. Please also include in any mailing your name, address and a description of the problem(s).

3. For the name of the nearest NECTECH authorized service center, call NECTECH at 800-836-0655.

LIMITATIONS OF LIABILITY

Except for the obligations specifically set forth in this warranty statement, we will not be liable for any direct, indirect, special, incidental, consequential, or other types of damages, whether based on contract, tort, or any other legal theory, whether or not we have been advised of the possibility of such damages. This warranty is in lieu of all other warranties express or implied, including, but not limited to, the implied warranties of merchantability or fitness for a particular purpose.

EXCLUSION OF DAMAGES

NECTECH' s liability for any defective product is limited to the repair or replacement of the product at our option. NECTECH shall not be liable for:

1. Damage to other property caused by any defects in this product, damages based upon inconvenience, loss of use of the product, loss of time, commercial loss; or

2. Any other damages whether incidental, consequential or otherwise. Some states do not allow limitation on how long an implied warranty lasts and/or do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations and exclusions may not apply to you.

HOW STATE LAW RELATES TO THE WARRANTY

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

FOR MORE INFORMATION, TELEPHONE 800-8360655 NEC TECHNOLOGIES, INC. 1250 N. Arlington Heights Road, Suite 500 Itasca, Illinois 60143-1248

WHAT WE WILL PAY FOR AND WHAT WE WILL NOT PAY FOR

We will pay labor and material expenses for covered items, but we will not pay for the following:

1. Removal or installation charges.

2. Costs of initial technical adjustments (set-up), including adjustment of user controls. These costs are the responsibility of the NECTECH dealer from whom the product was purchased.

3. Payment of shipping charges.

Note:

MUST have prior approval. To get approval, call NEC Technologies at 800-836-0655.

All products returned to NECTECH for service

Contents

How to Attach Options to the Plasma Monitor

......... 1

Introduction ..................................................... 2

Introduction to the PlasmaSync 42MP1

Plasma Monitor ....................................................... 2

The features you'll enjoy include: .............................. 2

Contents of the Package ........................................... 2

Part Names and Function ................................. 3

Front View .............................................................. 3

Rear View / Terminal Board ..................................... 4

Remote Controller .................................................... 5

Battery Installation and Replacement ......................... 6

Using the wired remote control mode ........................ 7

Operating Range .................................................... 7

Handling the remote controller ................................. 7

Installation...................................................... 8

Connecting Your PC Or Macintosh Computer ............ 9

Connections with Equipment that has a Digital Interface

Connecting Your Document Camera.......................... 9

Connecting Your VCR Or Laser Disc Player ................ 9

Connecting Your DVD Player .................................... 9

External Speaker Connections ................................ 10

Pin Assignments and Signal Levels

for 15 pin RGB (Analog) ..................................... 11

Pin Configuration and Signal

of the RGB 3 IN Connector (DVI Connector) ......... 11

..... 9

Basic Operations ............................................ 12

POWER ................................................................ 12

To turn the unit ON and OFF:................................... 12

VOLUME .............................................................. 12

To adjust the volume: ................................................ 12

MUTE ................................................................... 12

To cancel the sound:.................................................. 12

DISPLAY................................................................ 12

To check the settings:................................................ 12

DIGITAL ZOOM .................................................... 12

OFF TIMER............................................................ 13

To set the off timer: ................................................... 13

To check the remaining time:.................................... 13

Canceling the off timer ............................................. 13

Sound settings menu .............................................. 23

Adjusting the treble, bass and left/right balance .......23

Screen Settings Menu............................................. 24

Adjusting the Position, Size, Fine Picture,

Picture Adj ................................................................ 24

Function Settings Menu .......................................... 25

Setting the on-screen display .................................... 25

Adjusting the position of the menu display .............. 26

Setting the power management for computer images

POWER/STANDBY indicator .................................. 28

Setting the gray level for the sides of the screen....... 29

Setting the brightness level to the minimum............. 29

Setting the picture to suit the movie ......................... 30

Resetting to the default values .................................. 30

Option setting menu .............................................. 31

Setting the allocation of the audio connectors .......... 31

Setting the BNC connectors ...................................... 31

Setting a computer image to the correct RGB

select screen .............................................................. 32

Setting high definition image to the suitable

screen size ............................................................... 33

Adjusting the display position

in the RGB3 input mode ......................................... 33

Information Menu .................................................. 34

Checking the frequencies and polarities

of input signals ..........................................................34

Setting the language for the menus ...........................34

Setting the video signal format ................................. 35

....... 27

External Control ............................................ 36

Table for Signals Supported ............................ 44

Supported resolutions ............................................ 44

Troubleshooting ............................................. 45

Specifications ................................................. 46

WIDE Operations ............................................ 14

Watching with a wide screen (manual).................... 14

When watching videos or high definition

laser discs .................................................................. 14

Watching computer images with a wide screen........ 15

OSM Controls ................................................. 16

Menu Operations .................................................. 16

Picture Settings Menu ............................................. 18

Adjusting the picture ................................................. 18

Setting the picture mode according to the

brightness of the room .............................................. 19

Setting the color temperature .................................... 20

Adjusting the color to the desired quality ................. 21

Reducting noise in the picture .................................. 22

How to Attach Options to the Plasma Monitor

You can attach your optional mounts or stand to the plasma monitor in one of the following two ways:

* While it is upright. (See Drawing A) * As it is laid down with the screen face down (See Draw-

ing B). Lay the protective sheet, which was wrapped around the monitor when it was packaged, beneath the screen surface so as not to scratch the screen face.

• This device cannot be installed on its own. Be sure to use a stand or original mounting unit. (Wall mount unit, Stand, etc) * See page 2.

• For correct installation and mounting it is strongly recommended to use a trained, authorized NEC dealer.

Failure to follow correct mounting procedures could result in damage to the equipment or injury to the installer.

Product warranty does not cover damage caused by improper installation.

Drawing A

Drawing B

Ventilation Requirements for enclosure mounting

To allow heat to disperse, leave space between surrounding objects as shown on the diagram below when installing.

31mm (1.22")

Wall

1110mm (43.7")

31mm (1.22")

(2")

(29.5")

748

(2") 50

Wall

Introduction

Introduction to the PlasmaSync 42MP1 Plasma Monitor

NEC's PlasmaSync™ is a seamless blend of cutting-edge visual technology and sophisticated design. At 42-inches, with a 16:9 aspect ratio, the PlasmaSync 42MP1 certainly makes a big impression. However, at a mere 3.5 inches/ 89mm thin, the monitor's sleek techno-art lines blend in well with your environment. PlasmaSync's crisp, vivid image quality will transform data from any graphic medium from PCs to DVD players- into art. And weighing only

70.6 lbs/ 32 kg, it actually can be hung almost anywhere. NEC has made sure that a host of multimedia resources can be easily connected and displayed as brilliantly as intended on the PlasmaSync™ monitor.

The features you'll enjoy include:

• 42-inch screen

• 16:9 aspect ratio

• Capsulated Color Filter (CCF) and black matrix

• 3.5 inch / 89 mm thin

• 70.6 lbs/ 32 kg light

• High-resolution screen: 853480 pixels

• 160-degrees of off-axis viewing, horizontally and vertically.

• Flicker - and warp - free display provides excellent image geometry even in screen corners

• Not affected by magnetic fields, no color drift or edge distortion.

•VGA, SVGA, XGA, SXGA(60Hz), computer signal compatibility

• NTSC, PAL, SECAM, composite and S-Video signal compatibility

• 480P, 1080I, 720P and HDTV signal compatibility

• PCs, VCRs, Laser Disc and DVD player source compatibility

• AccuBlend™ scan conversion automatically converts VGA, SVGA and SXGA signals to the panel's native resolution

• RGB input (3*), Video input (3), DVD/HD input (2*), Audio input (3), External Control input (1)

• AccuColor control system provides user selectable onscreen color temperature settings

•New Drive Technology

• Component video input terminal for DVD, 15.75kHz (Y, CB, CR)

• NEC's OSM™ menu-driven on screen control system that makes image adjustments a snap

•Seven languages (English, German, French, Italian, Spanish, Swedish, and Japanese)

Contents of the Package

 PlasmaSync™ 42MP1 plasma monitor  Power cord  RGB cable (Mini D-Sub 15-pin to Mini D-Sub 15-

pin connector)

 Adapter for Macintosh  Remote control unit with two AAA Batteries  User's manual  Wired Remote cable  Safety metal fitting*  Screw for safety metal fitting*  Ferrite core (small2, large1)

* These are fittings for fastening the unit to a wall to

prevent tipping due to external shock when using the stand (option). Fasten the safety fittings to the holes in the back of the monitor using the safety fitting mount screws.

Options

• Wall mount unit

• Ceiling mount unit

• Tilt mount unit

• Tabletop stand

• Speakers

• Others

*You can select RGB source or Component source for

the 5BNC terminal. When selecting an RGB input, the source is switched to the RGB input (3); when selecting a component input, the source is switched to the DVD/ HD input (2).

Part Names and Function

Front View

INPUT SELECT VOLUME

PROCEED

VOLUME

DOWN LEFT/– RIGHT/+UP

1 PROCEED

Sets the on-screen display (OSM) mode and displays the main menu.

2 VOLUME Down and Up

Adjust the volume. Functions as the CURSOR (▲/▼) buttons in the On-screen display (OSM) mode.

3 LEFT/– and RIGHT/+

Enlarges or reduces the image. Functions as the CURSOR ( / ) buttons in the On-screen display (OSM) mode.

POWER/STANDBY

INPUT SELECT

/EXIT

POWER/STANDBY

5 POWER/STANDBY indicator

When the power is on.............................Lights green.

When the power is in the standby mode ... Lights red.

6 Power

Turns the monitor's power on and off.

7 Remote sensor window

Receives the signals from the remote control unit.

4 INPUT SELECT / EXIT

Switches the input, in the following order:

VIDEO1→→VIDEO2 RGB3←RGB2←RGB1

VIDEO3 DVD/HD

→

→

←

Functions as the EXIT buttons in the On-screen display (OSM) mode.

Rear View/ Terminal Board

SPEAKERS MUST HAVE MORE THAN 7WATT RATING IMPEDANCE 6 OHM

LEFT

RIGHT

EXTERNAL CONTROL

REMOTE CONTROL

CONTROL LOCK ON/ OFF

AC IN

C D

SPEAKERS MUST HAVE MORE THAN 7WATT RATING IMPEDANCE 6 OHM

LEFT

RIGHT

EXTERNAL CONTROL

REMOTE CONTROL

CONTROL LOCK ON/ OFF

AC IN

AUDIO 3 AUDIO 2 AUDIO 1 RGB2/ DVD2/ HD2

RGB 3

(Digital RGB)

RGB 3

(Digital RGB)

RGB 1

R/CR/PR

G/Y

B/CB/PB

L(MONO)

VIDEO 1

VIDEO 2

VIDEO 3

L(MONO)

CB/CR

PB/PR

L(MONO)

RGB 1

R/PR

R/C

G/Y

B/PB

B/C

L(MONO)

VIDEO 1

VIDEO 2

VIDEO 3

L(MONO)

B/PB

CR/P

L(MONO)

AUDIO 3 AUDIO 2 AUDIO 1 RGB2/ DVD2/ HD2

A EXT SPEAKER L and R

Connect speakers here.

B EXTERNAL CONTROL

This terminal is used when power ON/OFF, input selection and AUDIO MUTE and other controls are operated externally (by external control). See also page 36 for external control.

C REMOTE CONTROL

Connect the supplied remote cable here.

D CONTROL LOCK

When “CONTROL LOCK” is set “ON”, the buttons on the set's control panel do not function.

E AC IN

Connect the included power cord here.

F RGB3 (DVI 29pin)

Inputs a digital RGB signal (TMDS).

G RGB1

Inputs the analog RGB signal of personal computer, etc.

H RGB2/ DVD2/ HD2

RGB2: Inputs the analog RGB signal. DVD2/ HD2: Connect DVD's, high definition Laser

Discs, etc. here.

I VIDEO1, 2, 3

Connect VCR's, DVD's or LaserDiscs, etc. here.

J DVD1 / HD1

Connect DVD's high definition LaserDiscs, etc. here.

K AUDIO1, AUDIO2, AUDIO3

These are audio input terminals. The input is selectable. Set which video image to allot them to on the menu screen.

Remote Controller

POWER

OFF

RGB/PC DVD/HD

POSITION

/CONTROL

VIDEO

POINTER

ZOOM

VOLUME

–

MUTE

WIDE

OFF TIMER

PROCEED

EXIT

–

DISPLAY

C D

2 RGB/PC

Press this button to select RGB/PC as the source.

→ RGB1 → RGB2 → RGB3 

RGB/PC can also be selected using the INPUT SELECT button on the monitor. The input switches as follows each time the button is pressed:

VIDEO1→→VIDEO2 RGB3←RGB2←RGB1

VIDEO3 DVD/HD

→

→

←

3 VIDEO

Press this button to select VIDEO as the source.

→ VIDEO1 → VIDEO2 → VIDEO3 

VIDEO can also be selected using the INPUT SELECT button on the monitor. The input switches as follows each time the button is pressed:

VIDEO1→→VIDEO2 RGB3←RGB2←RGB1

VIDEO3 DVD/HD

→

→

←

4 DVD / HD

Press this button to select DVD/HD as the source.

DVD/HD can also be selected using the INPUT SELECT button on the monitor. The input switches as follows each time the button is pressed:

VIDEO1→→VIDEO2 RGB3←RGB2←RGB1

VIDEO3 DVD/HD

→

→

←

5 PROCEED

Press this button to access the OSM controls. Press this button during the display of the main menu to go to the sub menu.

REMOTE CONTROLLER

RD-337

1 POWER ON/OFF

Switches power on/off. (This does not operate when POWER/STAND BY indicator of the main unit is off.

6 EXIT

Press this button to exit the OSM controls in the main menu. Press this button during the display of the sub menu to return to the main menu.

7 CURSOR (▲ / ▼ /  / )

Use these buttons to select items or settings and to adjust settings.

8 POINTER

Press this button to display the pointer.

9 VOLUME (+ /–)

Adjust the volume.

0 ZOOM (+ /–)

Enlarges or reduces the image

A MUTE

Mutes the sound.

B WIDE

The type of broadcast is detected automatically, and the recommended wide screen mode is set.

C DISPLAY

Displays the source settings on the screen.

D OFF TIMER

Activates the off timer for the unit.

E Remote Jack

Insert the plug of the supplied remote cable when using the supplied remote control unit in the wired condition.

F Remote control signal transmitter

Transmits the remote control signals.

Battery Installation and Replacement

Insert the 2 "AAA" batteries, making sure to set them in with the proper polarity.

1.Press and open the cover.

2.Align the batteries according to the (+) and (–) indication inside the case.

3.Replace the cover.

REMOTE

CONTROL

EXTERNAL

CONTROL

Using the wired remote control mode

Connect the included remote control cable to the remote control unit's "REMOTE CONTROL" terminal.

When the cable is connected, the mode automatically switches to wired remote control.

When the wired remote control mode is used, the remote control unit can be operated even if no batteries are loaded.

SPEAKERS MUST HAVE MORE THAN 7WATT RATING IMPEDANCE 6 OHM

LEFT

RIGHT

EXTERNAL CONTROL

REMOTE CONTROL

CONTROL LOCK ON/ OFF

AC IN

Operating Range

* Use the remote controller within a distance of about 7 m

/ 23ft. from the front of the monitor's remote control sensor and at a horizontal angle of within 30°.

*The remote control operation may not function if the

monitor's remote control sensor is exposed to direct sunlight or strong artificial light, or if there is an obstacle between the sensor and the remote control unit.

DOWN UP

VOLUME

INPUT SELECT /EXITLEFT/– RIGHT/+

POWER/STANDBY

Remote Control Cable

To Remote Jack

CONTROL LOCK ON/ OFF

Approx. 7m/ 23ft

30˚ 30˚

Handling the remote controller

• Do not drop or mishandle the remote control unit.

• Do not get the remote control unit wet. If the remote gets wet, wipe it dry immediately.

•Avoid heat and humidity.

• When not using the remote control unit for a long period, remove the batteries.

• Do not use new and old batteries together, or use different types together.

• Do not take apart the batteries, heat them, or throw them into a fire.

• When using the remote control unit in the wireless condition, be sure to unplug the remote cable from the REMOTE CONTROL terminal on the monitor.

Installation

Personal computer with a digital RGB output

Signal cable (supplied) To Mini D-Sub 15 pin connector on the plasma monitor

RGB 3

(Digital RGB)

RGB 1

R/CR/P

G/Y

B/C

B/PB

L(MONO)

VIDEO 1

VIDEO 2

VIDEO 3

L(MONO)

B/PB

DVD1/HD1

CR/P

L(MONO)

AUDIO 3 AUDIO 2 AUDIO 1 RGB2/ DVD2/ HD2

To video, S-video inputs on the plasma monitor

IBM VGA or Compatibles

Macintosh or Compatibles

(Desk top type)

Monitor adapter for Macintosh (supplied)

VCR or Laser Disc Player

Document Camera

DVD Player

Connecting Your PC Or Macintosh Computer

Connecting your PC or Macintosh computer to your plasma monitor will enable you to display your computer's screen image for an impressive presentation. The plasma monitor supports the signals described on page 44.

To connect to a PC, Macintosh or compatible graphics adapter, simply:

1. Turn off the power to your plasma monitor and computer.

2. If your PC does not support XGA/SVGA/VGA you will need to install an XGA/SVGA/VGA graphics board. Consult your computer's owner's manual for your XGA/SVGA/VGA configuration. If you need to install a new board, see the manual that comes with your new graphics board for installation instructions.

3. The plasma monitor provides signal compatibility up to VESA 12801024@60Hz (SXGA). However, it is not recommended to use this resolution due to image readability on the monitors 853480 native pixel resolution panel.

4. Use the signal cable that's supplied to connect your PC or Macintosh computer to the plasma monitor. For Macintosh, use the supplied monitor adapter to connect to your computer's video port.

5. Turn on the plasma monitor and the computer.

6. If the plasma monitor goes blank after a period of inactivity, it may be caused by a screen saver installed on the computer you've connected to the plasma monitor.

When using a Macintosh with the plasma monitor, the following four display standards are supported using the included Macintosh adapter :

13" fixed mode 16" fixed mode 19" fixed mode 21" fixed mode

The 13" fixed mode is recommended for the plasma monitor.

Connecting Your Document Camera

You can connect your plasma monitor to a document camera. To do so, simply:

1. Turn off the power to your plasma monitor and document

2. Use a standard video cable to connect your document camera

3. Turn on the plasma monitor and the document camera.

Note:

more information about your camera's video output requirements.

Connecting Your VCR Or Laser Disc Player

Use common RCA cables (not provided) to connect your VCR or laser disc player to your plasma monitor. To make these connections, simply:

1. Turn off the power to your plasma monitor and VCR or laser

2. Connect one end of your RCA cable to the video output

3. Turn on the plasma monitor and the VCR or laser disc player.

Note:

for more information about your equipment's video output requirements.

camera.

to the Video input on your plasma monitor.

Refer to your document camera's owner's manual for

disc player.

connector on the back of your VCR or laser disc player, connect the other end to the Video input on your plasma monitor. Use standard RCA audio patch cords to connect the audio from your VCR or laser disc player to your plasma monitor (if your VCR or laser disc player has this capability). Be careful to keep your right and left channel connections correct for stereo sound.

Refer to your VCR or laser disc player owner's manual

Connections with Equipment that has a Digital Interface

Connections can be made with equipment that is equipped with a digital interface compliant with the DVI (Digital Visual Interface) standard. * Use a DVI 29-pin signal cable (available separately) and the

ferrite cores (supplied) when making connections to the RGB3 IN (DVI) connector of the main unit. Note that the RGB3 IN(DVI) terminal does not support analog RGB input source.

Note:

1. Input TMDS signals conforming to DVI standards. The TMDS input corresponds to 1 link.

2. To maintain display quality, use a cable with a quality prescribed by DVI standards that is within 5 meters in length.

Connecting Your DVD Player

You can connect your plasma monitor to a DVD player. To do so, simply:

1. Turn off the power to your plasma monitor and DVD player.

2. Use a standard video cable to connect your DVD player to the Y, Cb, and Cr inputs on your plasma monitor. Or use the DVD-player's S-Video output. Use a standard SVideo cable to connect to the S-Video input on the plasma monitor.

3. Turn on the plasma monitor and the DVD player.

External Speaker Connections

SPEAKERS MUST HAVE MORE THAN 7WATT RATING IMPEDANCE 6 OHM

LEFT

RIGHT

EXTERNAL CONTROL

REMOTE CONTROL

CONTROL LOCK ON/ OFF

AC IN

LEFT

RIGHT

RGB 3

(Digital RGB)

RGB 1

R/CR/PR

G/Y

B/CB/PB

L(MONO)

VIDEO 1

VIDEO 2

VIDEO 3

L(MONO)

CB/CR

PB/PR

L(MONO)

AUDIO 3 AUDIO 2 AUDIO 1 RGB2/ DVD2/ HD2

External speakers may be connected to the plasma monitor to reproduce sound from VIDEO, DVD or RGB signal sources.

External speakers may be connected directly to the SPEAKERS terminals or indirectly by connecting a stereo system amplifier to the audio outputs.

CAUTION:

Unplug the plasma monitor and all connected components before connecting external speakers. Use only speakers with 6-ohm impedance and a power output rating of 7 watts or more.

To connect external speakers directly to the plasma monitor:

1. Strip the ends of the speaker wires.

2. Press down the tabs below the SPEAKERS terminals, insert the speaker wire and release the tab to secure the speaker wire connection:

[a] Connect the right speaker (located at right side

of the monitor when viewed from the front) positive (+) wire to RIGHT +.

[b] Connect the right speaker negative (–) wire to

RIGHT -.

[c] Connect the left speaker negative (–) wire to

LEFT–.

[d] Connect the left speaker positive wire (+) to

LEFT+.

+ 37 hidden pages