NEC MultiSync XG-852C, MultiSync XG-1352C Setup Manual

Download

MultiSync XG85RP/XG85RPW

MultiSync XG135RP

Large Screen MultiSync Rear Projection System

Set-Up Manual

Model Number:

XG-852C/XG-1352C

The projector must be assembled by qualified installation technicians.

12345

CONTENTS.

INSTALLATION (for qualified installation technicians) .............. 4

Assembly Instructions.................................................................4

PART NAMES AND FUNCTIONS ......................................... 8

Front Terminal Panel ...................................................................8

Rear Control Panel ......................................................................8

Optional Boards.........................................................................10

Remote Control Unit..................................................................12

Battery installation and replacement ...................................15

Remote control cautions.....................................................15

Handling remote control and batteries ................................15

Set-Up (for service personnel)

BEFORE SET-UP ......................................................... 18

Displaying the Menu and Adjustment Screens ..........................18

Storing Projector Settings (Automatic Save Feature) ................19

On ADJUST MODE ....................................................................21

Test Pattern...............................................................................22

SIGNAL ENTRY............................................................23

Signal Entry Procedures ............................................................23

Checking and Setting Various Parameters ................................35

ADJUSTMENT .............................................................44

Set-Up Procedure......................................................................44

Electrical Focus Adjustment ......................................................45

Alignment Adjustment...............................................................49

Static Convergence Adjustment ................................................55

Dynamic Convergence Adjustment............................................56

Color Temperature and White Balance Adjustment ...................66

R, G, and B Gain Adjustment.....................................................67

PASSCODE................................................................ 68

Entering Passcode.....................................................................68

Registering Passcode................................................................69

Changing Your Passcode ..........................................................71

Canceling Your Passcode..........................................................73

SETTING .................................................................. 74

Displaying the Various Setting Features ....................................74

Projection Type Selection..........................................................75

Connecting to the Switcher .......................................................77

Default Input Selection ..............................................................79

Focus Edge Mode...................................................................... 82

S-Video Mode Selection ............................................................84

Video Mode Selection................................................................86

Auto Power ON Mode Setting....................................................88

Warm-Up Mode Setting ............................................................90

Automatic Save Feature.............................................................92

Phosphor Saver Setting ............................................................94

Signal Switching Mute Mode Setting ........................................96

Direct Entry Access Setting .......................................................98

Blue Focus Tracking Setting....................................................100

Optional Terminal Baud Rate Selection ...................................101

RGB/COMPONENT Search Setting .......................................... 102

On-Screen Display Mode Setting.............................................104

On-Screen Display Color Setting .............................................106

Date, Time Display Setting ...................................................... 108

Entering Date and Time ...........................................................110

PJ Address Display Setting .....................................................112

"NEW SIGNAL" Message Display Setting .................................113

Auto Sequence Setting ............................................................114

Address Setting.......................................................................123

Projector Version Number.......................................................126

Checking and Setting the Running Time .................................127

Viewing Default Data ..............................................................128

REFERENCE ADJUSTMENT............................................ 129

REF. ADJUST menu.................................................................129

ASTIG Adjustment...................................................................130

Bright Uniformity Adjustment..................................................132

White Uniformity Adjustment ..................................................133

Rester Centering Adjustment ..................................................134

Appendix

TIMING CHARTS ........................................................ 136

Pre-set Signals........................................................................136

Input Signal Reference Chart...................................................137

Input Signal Timing .................................................................138

MESSAGE LIST.......................................................... 139

12345

INSTALLATION.

Assembly Instructions

NOTE: Tools Needed for Installation: One 7/16 open end or box end wrench. Note: Ratchet and sockets can be substituted for the

above wrenches.

STEP 1. After uncrating both upper and lower cabinets roll the Lower Cabinet into a position which allows ample working space

around the cabinet.

STEP 2. (Refer to Fig.1) Before lifting the Upper Cabinet test the weight by lifting one side slightly off the floor. With a minimum

of two people (four may be required) and with one hand firmly in Hand Grip and the other under the rear side of cabinet lift and place upon lower cabinet. (NOTE: Align plastic feet with the two round holes in top of lower cabinet.)

FIG.1

HAND GRIP

STEP 3. (Refer to Fig.2) For more structural security bolt the Upper Cabinet to the Lower Cabinet with 4 ea. 1/4 x 1 1/2 hex bolts

and washers (provided). (NOTE: Access fastening locations through Front Access Cover and Hinged Side Grills in lower cabinet see Fig. 3&7)

FIG.2

STEP 4. (Refer to Fig.3) Remove Front Access Cover by grasping at top and bottom and pulling with quick firm pressure.

• Loosen the two 1/4 Turn Wing Fasteners and extend the two Sliding Projector Mounts.

FIG.3

SLIDING PROJECTOR MOUNT

1/4 TURN WING FASTENER

FRONT ACCESS COVER

STEP 5. (Refer to Fig.4) Set projector on four 3" foam packing corners or suitable blocks and roll cabinet forward until mounting holes

on projector are in line with those of the Sliding Projector Mount.

• (Refer to Fig.5) Remove blocks so that projector rests on Sliding Projector Mount. Then bolt projector to mounts with 1/ 4 bolts and washers (provided).

• Slide projector into cabinet and re-fasten 1/4 Turn Wing Fasteners.

FIG.4

ROLL FORWARD

PROJECTOR

FIG.5

3" FOAM PACKING CORNERS

STEP 6. (Refer to Fig.6) Unlatch the two Lift & Turn latches at the rear of the Upper Cabinet and pivot the Mirror Shroud all the way

out.

• With the Mirror Shroud held at the maximum out position, re-latch the Lift & Turn latches.

FIG.6

LIFT & TURN MIRROR SHROUD LATCH.

STEP 7. (Refer to Fig.7) Attach auxiliary Electronic Equipment (optional) to the Rack Mount Rails located behind the Hinged Side

Grills.

FIG.7

ELECTRONIC EQUIPMENT (rack mounted type)

HINGED SIDE GRILL (open position)

STEP 8. (Refer to Fig.8) Attach Speakers to the inside of the Hinged Side Grills with 8-32 x 3/4 pan head machine screws.

FIG.8

SPEAKERS MOUNTED TO SIDE GRILL

HINGED SIDE GRILL (open position)

STEP 9. Plug Projector Power Cord directly into the Projector at lower rear of Projection Cabinet.

• Run system cables through cable Grommet located at the lower rear of the Projection Cabinet. Note: Computer cables can be connected directly to the front of the projector.

STEP10. (Refer to Fig.6) Replace Front Access Cover by aligning with the Slide Grills and pushing with gentle pressure until catches

engage.

FIG.6

LIFT & TURN MIRROR SHROUD LATCH.

12345

PART NAMES AND FUNCTIONS

PART NAMES AND FUNCTIONS.

Rear

Open the front access cover to access the terminal panel. To remove the front access cover, grasp at top and bottom, and pull with quick firm pressure.

Front

OFF POWER ON AC INPUT

POWER STANDBY RC READY

5 6487

Terminal Panel

I H

ACAT OUT R/Cr G/Y B/Cb H/HV V S-VIDEO VIDEO OPTION REMOTE1 REMOTE2

INPUT SELECT

INDICATOR ON/OFF INPUT SELECT ENTER

POWER

J LK

L(MONO) R L(MONO) R L(MONO) R

RGB S-VIDEO VIDEO

AUDIO INPUT

OUT IN

F G

PART NAMES AND FUNCTIONS

Rear Panel

1 Power Switch (Main power)

To turn on the main power to the projector press the switch to the ON position (I). The STANDBY and the RC READY indicator will light. In this condition you can start up the projector by pressing the POWER ON button on the remote control or the POWER button on the rear panel. Press to the OFF position (0) to turn the main power off.

NOTE: When turning off the main power,first return the projector to the standby condition by pressing the POWER OFF button on the remote control or the POWER button on the rear panel and then turn off the main POWER switch.These procedures are necssary to protect your projector and the connected equipment.

2 AC INPUT

Connect the supplied power cord here.

Front Panel

3 Remote Sensor

Receives the signal from the supplied remote control when used in the wireless mode.

4 POWER Indicator

Lights up when the projector is turned on.

5 STANDBY Indicator

Lights up when the projector’s main POWER switch is on Flashes when the projector is not connected with the Switcher correctly or when the Switcher is turned off.

6 RC READY Indicator

Lights up when the projector's main POWER switch is on. Flashes when the projector receives a signal from the remate control.

7 Two Digit Display

INDICATOR:

Displays projector error codes.(“00” in normal operation)

ON/OFF Switch:

Turns the INDICATOR on or off.

A Active Indicator (green LED)

Lights up when the INPUT A slot is selected.

R/Cr,G/Y, B/Cb, H H/V and V Input Terminals (INPUT A)

Connect R,G,B,H (Horizontal sync) and V (Vertical sync) outputs of the external equipment (such as the Switcher). If using a component with a combined sync (SYNC) output,connect it to the H/V terminal. When using

luminance and color-difference signals of HDTV and DVD, connect a Pr/Cr to the R, a Y to the G and a Pb/Cb to the B input of the projector.

C S-VIDEO Input Terminal

Connect to the S-video output of the external equipment such as a VCR with an S-video output.This terminal allows switching between S2 and S1 VIDEO input modes.

D VIDEO Input Terminal

Connect to the video output of the external equipment such as a VCR or laser disk player.

E OPTION Terminal

For system expansion such as PC-control.

F REMOTE 1 Terminal

This terminal allows external control of the projector from either the Switcher or from an external control.When the Switcher is used,connect to the REMOTE 1 terminal on the back of the Switcher.

NOTE: The ISS-6020/ISS-6020G Switcher is compatible with this projector.

G REMOTE 2 Terminal

IN: for the supplied service remote control. OUT: connect to a second projector’s IN terminal to relay the input at the IN terminal.

NOTE: The wireless control does not work when the plug of the supplied remote cable is inserted into the REMOTE 2 IN terminal.

H INPUT B

Slot for adding optional RGB or video input cards.

(INPUT A)

8 INPUT SELECT Buttons

INPUT: press to display the INPUT SELECT screen. SELECT: press to select an input by highlighting the

input terminal. ENTER: press to execute selection and to switch input.

9 POWER Button

Turns the projector on or off when the projector is in the standby condition (Main Power switch must be on and the STANDBY and the RC READY indicator lit).

0 ACAT OUT Terminal

This is a video output connector for the optional built in CCD camera. The CCD camera is needed in order to perform automatic convergence with the optional ACAT software.

I INPUT C

Slot for adding optional RGB or video input cards.

NOTE: The optional RGB INPUT and VIDEO INPUT modules can be installed in the INPUT B and INPUT C slots.

J RGB Audio Input Terminals (L/R)

Connect to the audio outputs of the external equipment such as ISS-6020/6020G.

K S-VIDEO Audio Input Terminals (L/R)

Connect to the S-video audio outputs of the external equipment such as a VCR with S-video outputs.

L VIDEO Audio Input Terminals (L/R)

Connect to the audio outputs of the external equipment such as a VCR.

PART NAMES AND FUNCTIONS

OPTIONAL Boards

VIDEO INPUT Board [XG VIDINA]

Front view

LRLR

VIDEO INPUT

1 Active Indicator (green LED) ...... Lights up when this board is selected.

2 VIDEO INPUT Terminal ............... Connects composite video output signals.

3 S-VIDEO INPUT Terminal ........... Connects S-video output signals.

4 VIDEO INPUT Terminal ............... Connects the audio outputs of the external equipment such as a VCR.

5 S-VIDEO INPUT Terminal ........... Connects the S-video audio outputs of the external equipment such as a VCR with

RGB INPUT Board [XG RGBINA]

Front view

RGB INPUT

R G B H/HV V

1 23

1 Active Indicator (green LED) ...... Lights up when this board is selected.

2 R Input Terminal.......................... Connects a Red output signal.

3 G Input Terminal ......................... Connects a Green output signal.

4 B Input Terminal.......................... Connects a Blue output signal.

5 H/HV Input Terminal.................... Connects horizontal sync or horizontal/vertical sync output signals.

6 V Input Terminal .......................... Connects a vertical sync output signal.

7 AUDIO Input Terminals............... Connects the audio outputs of the external equipment such as the ISS-6020/

VIDEO

S-VIDEO

312

S-video outputs.

456 7

6020G or a PC.

AUDIO INPUT

S-VIDEOVIDEO

AUDIO INPUT

RGB INPUT Board

Top view

8 Rotary Switch (S1001) 9 Jumper(S1002, S1003, S1004)

PART NAMES AND FUNCTIONS

The combination of the rotary switch and the jumper pins allows the projector to accept VIDEO or COMPONENT signals. Note that this board cannot accept RGB signals when board is set to VIDEO input.

Rotary switch (S1001)

Setting of Rotary switch and Jumpers

Rotary Switch(S1001)

0 1

* indicates factory preset.

SLOT FOR OPTIONAL MODULE

INPUT C slot

INPUT B slot INPUT A slot

ACAT OUT R/Cr G/Y B/Cb H/HV V S-VIDEO VIDEO OPTION REMOTE1 REMOTE2

Jumper (S1002, S1003, S1004)

No.

RGB

VIDEO

0 1 3

2, 4-9

Table for Setting Rotary Switch and Jumpers.

Input Signal

Jumpers (2, 3) Short (2, 3) Short (1, 2) Short

R terminal

VIDEO

Pr/Cr

G terminal

Y Y G

Setting of Rotary switch Mark

VIDEO OPTION RGB

VIDEO input COMPONENT input RGB input Not used

B terminal

Pb/Cb

L(MONO) R L(MONO) R L(MONO) R

RGB S-VIDEO VIDEO

AUDIO INPUT

OUT IN

Input

* No.3 is factory preset.

Board Identification

VIDEO

COMPONENT

RGB

Corresponding slot number

You can also select the input signal directly by pressing the INPUT “1” through “10” button. In this case INPUT buttons function as follows:

INPUT A slot

1 2 3 4 5

RGB VIDEO S-VIDEO

*2 *3

INPUT B slot

RGB/COMPONENT/VIDEO S-VIDEO

INPUT C slot

RGB/COMPONENT/VIDEO S-VIDEO

COMPONENT

*1 Some settings allow you to retrieve a COMPONENT signal automatically. See “RGB/COMPONENT Search Setting”. *2 When the optional RGB input board is installed and the RGB input is set, an RGB signal will be selected; when the RGB input

board is installed and the COMPONENT input is set, a COMPONENT signal will be selected; when the optional RGB input board is installed and the VIDEO input is set, a VIDEO signal will be selected. When the optional VIDEO input board is installed, a VIDEO signal will be selected.

*3 An S-VIDEO signal will be selected when :

1. the optional RGB input board is installed and the VIDEO input is set.

2. the optional VIDEO input board is installed.

PART NAMES AND FUNCTIONS

Remote control unit

OPERATE

1 ABC 2 DEF 3 GHI

PICTURE

4 JKL 5 MNO 6 PQR

MUTE

SOUND

7 STU 8 VWX 9 YZ /

MUTE

9 0

DISPLAY

STATIC

NORMAL ENTER

User Remote Control RC-6320

POWER

ON OFF

10 ,.

CAPTION

POWER INPUT

1 ABC 2 DEF 3 GHIOFFON

ADJUST

SOUND FUNC

SOUND MUTE

PHASETILT

ADDRESS

4 JKL 5 MNO 6 PQRTEST

7 STU 8 VWX 9 YZ/

10 ,.

CAPTION

HELP INFO

RGBPOINTSTATIC

POSITION

CURSOR

INPUT LIST

KELVINFOCUS

OFF

OPERATE

PIC FUNC

PIC MUTE

DISPLAY

ENDCTL

U VS

B D

C J

BOW

AMPLIT

LINEAR

R G H

KEYSTN

PINCUS

NORMAL

STORE

CTL ENTER END

NOTE: The full function remote control is designed for setup adjustment. Use the user remote control for normal operation.

Full Function Remote Control RC-6321

PART NAMES AND FUNCTIONS

1POWER Buttons (ON/OFF)

Press the ON button to turn the projector on when the projector is in the standby condition (STANDBY and RC READY indicators lit). Press the OFF button to return the projector to the standby condition.

2TEST Button

Press to display the “TEST PATTERN” menu from which you can select a test pattern.

3ADJUST Button

Press to display the “ADJUST” menu.

4OPERATE Button

Press to display the “OPERATE” menu.

5Backlight Switch

Turns the backlight on and off. If no button operation is made within 30 seconds with the Backlight ON, the Backlight will turn off to conserve battery life.

6PIC FUNC Button

Press to display the picture adjustment screen.

NOTE: Some function items will not be available depending on the type of video signal.

7SOUND FUNC Button

Press to display the VOLUME adjustment screen. You can adjust the volume of the ISS-6020/ISS-6020G Switcher.

8PICTURE (PIC) MUTE Button

Press to mute the picture. Press again to display the picture. You can also mute the picture by holding down CTL and pressing PICTURE MUTE buttons. To restore the picture, holding down CTL and press PICTURE MUTE again. Or simply press END.

NOTE: When the picture is muted by using CTL and PICTURE MUTE buttons, even if input is switched to another or the power is turned off using the remote POWER OFF button, the mute cannot be canceled.

9SOUND MUTE Button

Press to mute the sound. Press again to return the sound.

0DISPLAY Button

Press to turn on or off the on-screen display. Pressing with CTL eliminates the on-screen display; pressing with CTL will restore display.

NOTE: Even if the on-screen display may be turned off with pressing CTL and DISPLAY, any adjustment will still change the projector’s memory settings. This mode is available even when an input is switched to another or the power is turned off using the POWER OFF button on the remote control. On-screen display mute function can be canceled by turning off the main power.

AFOCUS Button

Press to enter the FOCUS mode.Pressing with CTL will bring you to the ASTIG adjustment screen.

BSTATIC Button

Press to enter the STATIC mode. You can adjust the static convergence.

CPOINT Button

Press to enter the POINT mode. You can adjust the point convergence.

DTILT Button

Press to enter the TILT, SKEW mode. You can adjust the tilt and the skew of the projected image.

EBOW Button

Press to enter the BOW mode. You can adjust the horizontal and the vertical bow of the projected image. Pressing with CTL will bring you to the LINE DISTORTION adjustment screen.

FAMPLIT Button

Press to enter the AMPLITUDE mode. You can adjust the horizontal width and the vertical height of the projected image.

GLINEAR Button

Press to enter the LINEARITY mode. You can adjust the horizontal and the vertical linearity of the projected image. Pressing with CTL will bring you to the LINEARITYBALANCE adjustment screen.

HKEYSTN Button

Press to enter the KEYSTONE mode. You can adjust the horizontal and the vertical keystone of the projected image. Pressing with CTL button will bring you to the KEY-BALANCE alignment screen.

PART NAMES AND FUNCTIONS

IPINCUS Button

Press to enter the PINCUSHION mode. You can adjust the horizontal and the vertical pincushion of the projected image. Pressing with the CTL button will bring you to the PIN-BALANCE alignment screen.

JPHASE Button

For service personnel only.

KINPUT Button

Selects menus and switches input signals.

LHELP Button

Press to display the explanation of the current selected function and available functions.

MINPUT LIST Button

Press to display the memory list of the recorded input signals.

NINFO Button

Press to display the various parameters and settings of the currently displayed image. Pressing with the CTL button displays some of items available in SETTING MODE.

OKELVIN Button

Press to enter the KELVIN mode. You can adjust the color temperature and, the white and the black level.

PPOSITION Button

Press to enter the position mode. You can adjust the horizontal, vertical position and horizontal, vertical blanking and image size.

QR, G, and B Buttons

Turn each CRT beam on and off separately. When using with the CTL button, you can select the CRT to be adjusted during convergence and focus adjustments. Note that the G button is only on the full function remote control.

SNORMAL Button

Returns the standard level for each signal. When pressed once, the confirmation message will be displayed. When “YES” is selected and ENTER is pressed, the data will be returned to the standard level. While holding down the CTL button, press the NORMAL button to display the “LOAD/CANCEL” menu to select either LOAD (last stored level) or CANCEL (data cancelled).

TSTORE Button

Memorizes the adjustments setting of each signal separately. When pressed once, the confirmation message “STORE?” will be displayed. When selecting “YES” and ENTER, the data will be stored in memory.

UEND Button

Ends the adjustment mode.

VENTER Button

Executes menu selection and switches to selected input.

WCTL Button

Used in conjunction with other buttons, similar to a shift key on a computer.

XRemote Control Jack

Insert the plug of the supplied remote cable here when the full function remote control is used in the wired condition.

YCAPTION Button

Press to display the CLOSED CAPTION menu.

ZADDRESS Button

Press to display the ADDRESS menu. Pressing with CTL allows you to specify the address for the remote control.

RCURSOR Buttons

Used for increasing and decreasing control levels, cursor movement and convergence adjustments.

Battery installation and replacement

PART NAMES AND FUNCTIONS

User remote control (RC-6320)

Press down on the battery compartment cover and slide

the cover in the direction of the arrow.

2 Install the two new batteries, making sure that their

polarity matches the , . diagrams inside the battery compartment. Incorrect polarity could damage the unit.

Full function remote control (RC-6321)

Press down on the battery compartment cover and slide

the cover in the direction of the arrow.

2 Install the two new batteries, making sure that their

polarity matches the , . diagrams inside the battery compartment. Incorrect polarity could damage the unit.

3 Close the battery compartment cover.3 Close the battery compartment cover.

NOTE: The remote control is powered by two alkaline 1.5V AA batteries.

Remote control cautions

Use the remote control within a distance of about 7m (23 ft.) and at 30 degrees angle left and right.

Handling remote control and batteries

• Do not drop or mishandle the remote.

• Do not get the remote wet. If the remote gets wet, wipe it dry immediately.

• Avoid heat and humidity.

• When not using the remote for a long period, remove the batteries.

• Do not use new and old batteries together, or use different types together.

• Do not take apart the batteries, heat them, or throw them into a fire.

• Avoid using the full function remote control as wireless with the backlight switch ON for an extended period of time. This can cause short battery life.

Set-Up

(for service personnel)

Set-Up

The Signal Entry chapter explains how to register a new input signal and how to set various parameters of the currently selected signal. The Adjustment chapter gives you the procedures for various adjustment such as focus, alignment, convergence. This chapter also explains the passcode. It is a convenient way to prevent any tampering of projector set-up information by unauthorized individuals. The Setting chapter gives you details on setting for various use.

CONTENTS

Before Set-Up ................................................18

Signal Entry....................................................23

Adjustment .....................................................44

Passcode .......................................................68

Setting............................................................74

Reference Adjustment .................................129

12345

BEFORE SET-UP.

Displaying the Menu and Adjustment Screens

Access of all set-up functions is done through the menu system. Depending upon button selection, your desired screen will be displayed as shown below:

ADJUST menu

NOTE: Some function items will not be used depending on the input video signal or connected peripheral equipment.

ADJUST

ADJUST menu

– ADJUST –

1 / SIGNAL ENTRY

2 / FOCUS

3 / ALIGNMENT

4 / CONVERGENCE

5 / KELVIN

6 / R,G,B GAIN

7 / PASSCODE

8 / OPTION

9 / REF. ADJUST

SIGNAL ENTRY screen FOCUS menu

– FOCUS – 1 / CENTER

2 / EDGE ALL 3 / EDGE SEPA. 4 / CORNER

ALIGNMENT menu

– ALIGNMENT – 01 / TILT, SKEW

02 / BOW 03 / AMPLITUDE 04 / LINEARITY 05 / KEY-STONE 06 / PIN-CUSHION 07 / LINEAR-BAL. 08 / KEY-BALANCE 09 / PIN-BALANCE 10 / LINE DIST. 11 / R,G,B POINT 

CONVERGENCE menu

– CONVERGENCE – 1 / TILT, SKEW 2 / BOW 3 / AMPLITUDE 4 / LINEARITY 5 / KEY-STONE 6 / PIN-CUSHION 7 / LINEAR-BAL



8 / LINE DIST. 9 / POINT 10/ PHASE

– KELVIN – 1 / COLOR TEMP. 2 / WHITE BAL.

Adjustment screen

PASSCODE menu

OPTION menu

– OPTION – 1 / SETTING MODE 2 / MENU MODE 3 / SEQUENCER 4 / PJ ADDRESS 5 / VERSION 6 / HOUR METER 7 / DEFAULT DATA

– REF. ADJUST – 1 / ASTIG 2 / BRIGHT UNIFORM. 3 / WHITE UNIFORM. 4 / RASTER CENTERING

FOCUS

Adjustment screen

CTL

Sub menu and Adjustment screen

CTL

R,B

Sub menu and Adjustment screen

KELVIN

NEW PASSCODE? input screen

PASSCODE DISABLE? menu

Sub menu / Setting screen

CTL

ADJUST

TILT

BOW

AMPLIT

LINEAR

KEYSTN

PINCUS

CTL

POINT

TILT

BOW

AMPLIT

LINEAR

KEYSTN

PINCUS

CTL

POINT

PHASE

LINEAR

KEYSTN

PINCUS

BOW

LINEAR

BOW

Storing Projector Settings (Automatic Save Feature)

You have two options to store projector settings in the memory: automatically and manually.

NOTE: Storing time is four seconds.

• The Automatic Save Feature mode has been set to DISABLE by factory. For information on setting, see “Automatic Save Feature” on page 92.

mWhen the Automatic Save Feature mode is set to “ENABLE”, projector settings will be stored in the projector’s memory automatically. Settings are stored automatically when any one of the following procedures is performed:

• The END button is pressed several times to return the adjustment screen to the source screen.

• One input is switched to another.

• The projector is turned off.

• After every 10 minutes of elapsed time.

BEFORE SET-UP

mWhen the Automatic Save Feature mode is set to “DISABLE”, projector settings can be stored in the projector’s memory manually. When you try to return the source screen by pressing END several times, the “STORE ?” menu is displayed. To manually save settings, proceed as follows:

1. Use the END button to display the “STORE” menu from the

current adjustment screen or menu.

2. Use the CURSOR or button to highlight “CURRENT”,

“NEW”, or “CANCEL” and press ENTER.

Items to select

• CURRENT ------Overwrites the currently projected signal and

saves the settings. NOTE: An unregistered signal cannot be stored under the ''CURRENT'' settings.

• NEW ------------ Starting at memory location No.51, this function

saves an unregistered signal as a new signal in memory.

• CANCEL -------- Does not save settings.

CURRENT

STORE ?

NEW CANCEL

BEFORE SET-UP

mWhen selecting “NEW”

The current settings are registered as a new signal and are saved to an unassigned line starting at memory location No.51. A registered name is automatically given. The “NEW ENTRY?” menu will be displayed.

Use the CURSOR or button to highlight “YES” or “NO” and press ENTER.

Items to select

• YES------------- Registers settings as a new signal and

saves the signal in an unassigned location starting at memory location No.51.

• NO -------------- Does not register settings.

A registered name is given as follows: VIDEO/S-VIDEO----- Video standard with a list number

e.g. NTSC51 or PAL52.

RGB --------------------- ”RGB” with a list number e.g.

RGB60.

NEW ENTRY? LIST No. ** NAME ******** YES NO

NOTE:

• If the Input list does not have any unassigned memory location starting at No. 51 then, the “NEW” item will be selectable. For signal registration see “SIGNAL ENTRY” on page 23.

• The Automatic Save Feature is available only for signals listed in the INPUT LIST.

On ADJUST MODE

The ADJUST mode contains various adjustment items for set-up. Open the ADJUST menu and select the item you wish to adjust. To display the ADJUST menu, proceed as follows:

1 Press the ADJUST button.

• The projector may ask for your passcode.

2 Enter your registered passcode.

BEFORE SET-UP

When a passcode has not been registered:

• Since no passcode is programmed at the factory, pressing the ADJUST button will open the ADJUST menu.

• See “Entering Passcode”, “Registering Passcode”, “Changing Your Passcode” and “Canceling Your Passcode” on pages 68 through 73.

When your passcode has already been registered:

• When finishing the ADJUST mode, the “RETURN USER MODE?” menu will be displayed. If you select “YES” and press ENTER to end the ADJUST mode, you will have to enter your passcode to re-enter the ADJUST mode.

• When finishing the ADJUST mode by either selecting “NO” or pressing END, you do not need to enter your passcode to re-enter the ADJUST mode. To exit the ADJUST mode temporarily during adjusting, select “NO”.

PASSCODE?

****

BEFORE SET-UP

Test Pattern

This projector will generate a selection of test signals. Ten kinds of internal test patterns can be selected from the TEST PATTERN menu. To display the TEST PATTERN menu, proceed as follows:

1 Press the TEST button on the Full function remote control.

• The “TEST PATTERN” menu will be displayed.

• When the END button is pressed, the “TEST PATTERN” menu will disappear.

2 Use the CURSOR or button to highlight the test pattern you

wish to use and press ENTER.

• The selected test pattern will be displayed.

3 To return to the source screen, press the TEST and then the END

button.

• When the TEST button is pressed, the “TEST PATTERN” menu will be displayed and when the END button is pressed, the screen will be changed to the source screen.

• The projector will return to the original source screen by pressing the END button only when no menu or no adjustment screen is displayed.

– TEST PATTERN –

CROSS-HAIR

CROSS-COARSE CROSS-FINE DOT-COARSE DOT-FINE FOCUS WINDOW-WHITE ALL WHITE WINDOW-BLACK GRAY SCALE

NOTE: If there is no test pattern, the beams have been turned off by the R, G, and B buttons on the remote control.

Adjustment test pattern

CROSS-HAIR CROSS-COARSE CROSS-FINE DOT-COARSE

DOT-FINE

WINDOW-BLACK

H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H

FOCUS WINDOW-WHITE

GRAY SCALE

ALL WHITE

12345

SIGNAL ENTRY.

On Signal Entry

The projector uses a micro-processor to automatically read and distinguish between all video signals input at the same time. These signals are then used to make optimum adjustments for focus, convergence, alignment, etc. Various parameters must be registered into the micro-processor beforehand to ensure the video signals are recognized and adjusted to optimum quality. The Signal Entry registers these video signals in the SIGNAL ENTRY list and at the same time obtains the various parameters pertaining to these signals. Always access this mode first whenever inputting video signals for the first time so that you can register the video signals before making any adjustments. If the current input signal(s) has not been registered, the “UNREGISTERED SIGNAL” message is displayed on screen.

NOTE: If you have software which changes scanning mode due to the graphic board of your PC (such as VGA), it will be necessary to register signal entry for each scanning mode. This can be done using your PC by way of stopping the software in each scanning mode and performing a signal entry operation.

Signal Entry Procedures

To make the signal entry, proceed as follows: 1 Press the ADJUST button.

• The “ADJUST” menu is displayed.

NOTE: The projector may ask you to enter your passcode. See 68 for the explanation of the PASSCODE.

2 Use the CURSOR or button to highlight the “1/SIGNAL

ENTRY” line and press ENTER.

• The “SIGNAL ENTRY” list will be displayed.

• You can also select the “SIGNAL ENTRY” list directly by pressing the INPUT “1” button.

3 Use the CURSOR or button to select the desired line and

press ENTER.

• The Signal entry menu will be displayed.

– ADJUST –

1 / SIGNAL ENTRY

2 / FOCUS 3 / ALIGNMENT 4 / CONVERGENCE 5 / KELVIN 6 / R,G,B GAIN 7 / PASSCODE 8 / OPTION 9 / REF.ADJUST

NOTE: To advance to the next page or to the previous page, hold down the CTL button then press the CURSOR or button. To directly access a page, hold down the CTL button then press any one of the INPUT buttons.

Page / total pages – sheet No.

Connect condition of the Switcher

P01/10–1 SIGNAL ENTRY

STANDALONE

01 02 03 04 05 06 07 08 09 10

NAME NTSC3.58 NTSC4.43 PAL SECAM VESA1024

OUTPUT DATA : LIST NO.✻✻

SOURCE VIDEO VIDEO VIDEO VIDEO RGB

INPUT A A A A A

§ ©

Signal name

Input terminal

P01/10–2 SIGNAL ENTRY

STANDALONE

01 02 03 04 05 06 07 08 09 10

DATE 00/00/00 00/00/00 00/00/00 00/00/00 00/00/00

OUTPUT DATA : LIST NO.✻✻

Entry dateRgistered input module

15.74kHz

48.60kHz

Horizontal Frequency

Output data for the signal currently projected.

60.00Hz

50.00Hz

60.00Hz

Vertical Frequency

SIGNAL ENTRY



INPUT TERMINAL SELECT

INPUT A

INPUT B INPUT C 

4 Use the CURSOR or button to select the item and then press

ENTER.

• The Input terminal menu will be displayed.

Items to select

• NEW ENTRY ........ Registers a new signal.

• ENTRY COPY....... Copies any registered signal entry.

• ENTRY MOVE ...... Moves any registered signal entry.

• ENTRY DELETE ... Deletes any registered signal entry from

SIGNAL ENTRY.

• DATA COPY.........Copies gain data from any one of the

registered signals.

•

CHANGE DEFAULT

.Rewrites the data stored in DEFAULT AREA.

• SOURCE EDIT...... Changes setting various parameteres of the

registered signals.

NOTE: When a vacant line is selected, the “SIGNAL ENTRY” menu has three items only: “NEW ENTRY”, “ENTRY COPY” and “ENTRY MOVE”.

m Selecting “NEW ENTRY”

When connecting a signal for the first time, you need to register it into the projector’s memory. You can copy the initial setting for the new signal from any other signal that has already been registered or use the factory preset setting. To do this, proceed as follows:

1) Use the CURSOR or button to select “NEW ENTRY”

and press ENTER.

• The “INPUT TERMINAL SELECT” menu will be display.

SIGNAL ENTRY

NEW ENTRY

ENTRY COPY ENTRY MOVE ENTRY DELETE DATA COPY CHANGE DEFAULT SOURCE EDIT

SIGNAL ENTRY

NEW ENTRY

ENTRY COPY ENTRY MOVE

SIGNAL ENTRY

NEW ENTRY

ENTRY COPY ENTRY MOVE ENTRY DELETE DATA COPY CHANGE DEFAULT SOURCE EDIT

When using the projector in stand alone application:

Use the CURSOR or button to select one of the three slots, and press ENTER.

Items to select

• INPUT A.......... Standard installed terminal

• INPUT B.......... Optional board terminal

• INPUT C.......... Optional board terminal

Use the CURSOR or button to select “VIDEO”, “RGB”, “SVIDEO”, or “COMPO.” and press ENTER.

• The “NAME INPUT” screen will be displayed.

Items to select

•VIDEO......... Selecs the VIDEO input signal of this projector

•RGB............ Selects the RGB input signal of this projector

•S-VIDEO ..... Selects the S-VIDEO input signal of this projector.

•COMPO ...... Selects the Y/Cb/Cr input signal of this projector.

• Go on to Step 2).



VIDEO

RGB



S-VIDEO

COMPO.

When using with a single Switcher ISS-6020/ISS-6020G:

Use the CURSOR or button to select the input slot number of the Switcher and press ENTER.

• Input slot numbers are from 1 through 10.

Use the CURSOR or button to select “VIDEO”, “RGB”, “S-VIDEO” or “COMPO.” and press ENTER.

• The “NAME INPUT” screen will be displayed.

Items to select

• VIDEO ---------Selects the signal from the VIDEO input

terminal of the VIDEO input board.

• RGB ----------- Selects the signal from the RGB input terminal

of the RGB input board.

• S-VIDEO ------Selects the signal from the S-VIDEO input

terminal of the VIDEO input board.

• COMPO. ------Selects the signal as COMPONENT signal from

the RGB input terminal of the RGB input board.

MASTER

SLOT–01

SLOT–02 SLOT–03 SLOT–04 SLOT–05 SLOT–06 SLOT–07 SLOT–08 SLOT–09 SLOT–10



VIDEO

RGB



S-VIDEO

COMPO.

SIGNAL ENTRY

* Go on to Step 2).

NOTE: Signal registry is not possible unless the installed input board matches the selected signal. Check the installed input board and the slot number.

SIGNAL ENTRY

When using with two or more ISS-6020/ISS-6020G switchers:

Use the CURSOR or button to select the input slot number of the master Switcher and press ENTER. Then select the slot number of the slave Switcher and press ENTER.

• The “MASTER” menu will be displayed when the slot number of the master Switcher is selected.

• The “SLAVE” menu will be displayed when the slot number of the slave Switcher is selected.

• Input slot numbers are from 1 through 10.

Use the CURSOR or button to select “VIDEO”, “RGB”, “S-VIDEO” or “COMPO.” and press ENTER.

• The “NAME INPUT” screen will be displayed.

Items to select

• VIDEO ---------- Selects the signal from the VIDEO input terminal of the VIDEO input board.

• RGB ------------ Selects the signal from the RGB input terminal of the RGB input board.

• S-VIDEO ------- Selects the signal from the S-VIDEO input terminal of the VIDEO input board.

• COMPO.--------Selects the signal as COMPONENT signal from the RGB input terminal of the RGB input board.

MASTER

SLOT–01

SLOT–02 SLOT–03 SLOT–04 SLOT–05 SLOT–06 SLOT–07 SLOT–08 SLOT–09 SLOT–10



VIDEO

RGB



S-VIDEO

COMPO.

SLAVE

SLOT–01

SLOT–02 SLOT–03 SLOT–04 SLOT–05 SLOT–06 SLOT–07 SLOT–08 SLOT–09 SLOT–10

• Go on to Step 2).

NOTE: Signal registry is not possible unless the installed input board matches the selected signal. Check the installed input board and the slot number.

2) Input the source name by selecting one character at a time with the INPUT buttons 1 through 10 and by moving the cursor with the CURSOR button. After finishing the selection of the characters, press ENTER.

• Up to eight characters can be selected.

• Eight characters are assigned to one INPUT button.

• Whenever the INPUT button is pressed, characters will be

rotated.

For example:

A → B → C → 1 → A .....

• When pressing the INPUT button while holding down the CTL

button, another group of characters will be rotated.

For example:

a → b → c → ! → a .....

• The characters corresponding to these INPUT buttons are as

follows:

When using With CTL INPUT 1 A, B, C, and 1 a, b, c, and ! INPUT 2 D, E, F, and 2 d, e, f, and “ INPUT 3 G, H, I, and 3 g, h, i, and # INPUT 4 J, K, L, and 4 j, k, l, and $ INPUT 5 M, N, O, and 5 m, n, o, and % INPUT 6 P, Q, R, and 6 p, q, r, and & INPUT 7 S, T, U, and 7 s, t, u, and ‘ INPUT 8 V, W, X, and 8 v, w, x, and ( INPUT 9 Y, Z, ?, and 9 y, z, /, and ) INPUT 10 *, ,, ., and 0 ;, :, +, and -

SIGNAL ENTRY

NAME INPUT

––––––––

• If you have made an error in the input of a character, use the

CURSOR button and enter the correct letter or number. To delete one character, move the CURSOR button to the character to be deleted and then press the NORMAL button. To delete all the entered name, hold down the CTL button then press NORMAL.

• The “INITIAL DATA SELECT” menu will be displayed.

SIGNAL ENTRY

3) Use the CURSOR or button to select an item and press

ENTER.

Items to select

• DEFAULT ............. Uses the data stored in the DEFAULT AREA

• TEMPORARY.......Uses the data which is currently displayed

•

ENTRY NUMBER

....Copies the data from the registered signal

INITIAL DATA SELECT

DEFAULT TEMPORARY

ENTRY NUMBER

• When selecting “ENTRY NUMBER”, the “DATA COPY

SELECT SOURCE” message will be displayed at the bottom of the screen. Use the CURSOR or button to select the signal you wish to copy the initial settings from and press ENTER.

• The “DATA COPY MODE” menu will be displayed.

Use the CURSOR or button to select an item and press ENTER.

Items to select

• ALL...................... Copies all the settings.

• EXCEPT H-POSI&PHASE

............................Copies the settings except H-position and

Phase adjustments data.

• The “SOURCE INFORMATION” screen will be displayed.

• Pressing END will return to the “SIGNAL ENTRY” list. Go on

to Step 5.

NOTE: You can check and change various parameters on the “SOURCE INFORMATION” menu. See page 35.

P01/10-1

0 1 NTSC3.58 VIDEO A

02 03 04 05 06 07 08 09 10

SIGNAL ENTRY

NAME PAL

VGA480 NTSC

DATA COPY SELECT SOURCE

STANDALONE

SOURCE VIDEO

RGB S-VIDEO

DATA COPY MODE

ALL

EXCEPT H-POSI & PHASE

P01/03

SOURCE INFORMATION

INPUT A

A A

NAME

INPUT TERMINAL INPUT SOURCE

 VIDEO MODE

FREQUENCY  SYNC POLARITY

∗∗∗∗∗∗∗∗

 INPUT A RGB RGB FH = KHz

FV = Hz HD(-) VD(+)  

•

∗∗∗∗∗

•

∗∗∗∗∗

m When selecting “ENTRY COPY”

You can copy one of the registered input to another selected line. To do this, proceed as follows:

1) Use the CURSOR or button to select “ENTRY COPY” and then press ENTER.

• The “ENTRY COPY SELECT SOURCE” message will be

displayed at the bottom of the screen.

2) Use the CURSOR or button to select a line you wish to copy from and then press ENTER.

• The “ENTRY COPY SELECT DESTINATION” message will

be displayed at the bottom of the screen.

3) Use the CURSOR or button to select a line you wish to copy to and press ENTER.

• When there is already a registered signal in the selected line, the

“ENTRY DATA OVERWRITE?” prompt is displayed. Use the CURSOR or button to select “YES” or “NO” and then press ENTER.

• When the “ENTRY COPY END” message is displayed, this

completes the ENTRY COPY mode.

•

The “SIGNAL ENTRY” list is displayed. Go on to Step

SIGNAL ENTRY

NEW ENTRY

ENTRY COPY

ENTRY MOVE ENTRY DELETE DATA COPY CHANGE DEFAULT SOURCE EDIT

P01/10-1

0 1 NTSC3.58 VIDEO A

02 03 04 05 06 07 08 09 10

SIGNAL ENTRY

NAME PAL

VGA480 NTSC

ENTRY COPY SELECT SOURCE

ENTRY DATA OVERWRITE?

YES NO

STANDALONE

SOURCE VIDEO

RGB S-VIDEO

INPUT A

A A

Items to select

• YES ......... Overwrites the selected signal that has already

been registered.

• NO ........... Stops overwriting.

m When selecting “ENTRY MOVE”

You can move one of the registered inputs to another selected line. To do this, proceed as follows:

1) Use the CURSOR or button to select “ENTRY MOVE” and then press ENTER.

• The “ENTRY MOVE SELECT SOURCE” message will be

displayed at the bottom of the screen.

2) Use the CURSOR or button to select a line you wish to move and then press ENTER.

• The “ENTRY MOVE SELECT DESTINATION” message

will be displayed at the bottom of the screen.

3) Use the CURSOR or button to select a line you wish to move to and press ENTER.

• When there is already a registered signal in the selected

line, the “ENTRY DATA OVERWRITE?” prompt will be

SIGNAL ENTRY

NEW ENTRY ENTRY COPY

ENTRY MOVE

ENTRY DELETE DATA COPY CHANGE DEFAULT SOURCE EDIT

P01/10-1

0 1 NTSC3.58 VIDEO A

02 03 04 05 06 07 08 09 10

SIGNAL ENTRY

NAME PAL

VGA480 NTSC

ENTRY MOVE SELECT SOURCE

STANDALONE

SOURCE

VIDEO RGB S-VIDEO

INPUT

A A A

SIGNAL ENTRY

displayed. Use the CURSOR or button to select “YES” or “NO” and then press ENTER.

• When the “ENTRY MOVE END” message will be displayed, this completes the ENTRY MOVE mode.

• The “SIGNAL ENTRY” list will be displayed. Go on to Step 5.

Items to select

• YES ......... Overwrites the selected signal that has

already been registered.

• NO ........... Stops overwriting.

ENTRY DATA OVERWRITE?

YES NO

m When selecting “ENTRY DELETE”

You can delete one of the signals in the currently selected lines. To do this, proceed as follows:

1) Use the CURSOR or button to select “ENTRY DELETE” and then press ENTER.

• The “DELETE : SELECT START LINE” message

will be displayed at the bottom of the screen.

2) Use the CURSOR or button to select the first of the lines you wish to delete and then press ENTER.

• The “DELETE : SELECT END LINE” message

will be displayed at the bottom of the screen.

3) Use the CURSOR or button to select the end of the lines you wish to delete and then press ENTER.

• The “SELECT LINE DELETE?” menu will be

displayed.

4) Use the CURSOR or button to select "YES/NO" and then press ENTER.

• The “SIGNAL ENTRY” list will be displayed. Go

on to Step 5.

Items to select

• YES ......... Deletes the selected signal that has already

been registered.

• NO ........... Stops deleting.

SIGNAL ENTRY

NEW ENTRY ENTRY COPY ENTRY MOVE

ENTRY DELETE

DATA COPY CHANGE DEFAULT SOURCE EDIT

P01/10-1

0 1 NTSC3.58 VIDEO A

02 03 04 05 06 07 08 09 10

P01/10-1

01 NTSC3.58 VIDEO A 02 03 04 05

06 07 08 09 10

SIGNAL ENTRY

NAME PAL

VGA480 NTSC

DELETE : SELECT START LINE

SIGNAL ENTRY

NAME PAL

VGA480 NTSC

PAL

DELETE : SELECT END LINE

STANDALONE

SOURCE VIDEO

RGB S-VIDEO

STANDALONE

SOURCE

VIDEO RGB S-VIDEO

S-VIDEO A

INPUT A

A A

INPUT A

A A

SELECTED LINES DELETE? START LINE : 01 END LINE : 05

YES NO

m When selecting “DATA COPY”

To help assist in adjusting multiple inputs this projector has a feature called DATA COPY. This feature allows you to copy the memory data from one input to another input. By copying this data from an input that has already been adjusted to an existing input you will not have to do a complete adjustment. To do this, proceed as follows:

1) Use the CURSOR or button to select “DATA COPY” and then press ENTER.

• The “DATA COPY SELECT SOURCE” message will be

displayed at the bottom of the screen.

2) Use the CURSOR or button to select the signal to copy from and then press ENTER.

• The “DATA COPY SELECT DESTINATION” message

will be displayed at the bottom of the screen.

3) Use the CURSOR or button to select the signal you wish to copy to and press ENTER.

• The “DATA COPY MODE” menu will be displayed.

Use the CURSOR or button to select an item and press ENTER.

Items to select

• ALL................................... Copies all the settings.

• EXCEPT H-POSI&PHASE.. Copies the settings except Hposition and Phase adjustments data.

SIGNAL ENTRY

NEW ENTRY ENTRY COPY ENTRY MOVE ENTRY DELETE

DATA COPY

CHANGE DEFAULT SOURCE EDIT

P01/10-1

0 1 NTSC3.58 VIDEO A

02 03 04 05 06 07 08 09 10

SIGNAL ENTRY

NAME PAL

VGA480 NTSC

DATA COPY SELECT SOURCE

STANDALONE

SOURCE VIDEO

RGB S-VIDEO

DATA COPY MODE

ALL

EXCEPT H-POSI & PHASE

INPUT A

A A

• When “GAIN DATA COPY END” message will be displayed, this completes the DATA COPY mode.

• The “SIGNAL ENTRY” list will be displayed. Go on to Step 5

m When selecting “CHANGE DEFAULT”

All of the adjustment data of the selected signal will be stored in the DEFAULT AREA. The data stored in the DEFAULT AREA can be recalled by pressing the NORMAL button. Selecting “DEFAULT” from the “INITIAL DATA SELECT” menu during signal entry will utilize the data stored in the “DEFAULT AREA”.

NOTE: The default area is comprised of six locations depending on the horizontal frequency. The adjustment data will be stored in one of these locations corresponding its horizontal frequency. To refer the current default area, see "DEFAULT DATA" of the OPTION menu on page 128. To do this, proceed as follows:

SIGNAL ENTRY

NEW ENTRY ENTRY COPY ENTRY MOVE ENTRY DELETE DATA COPY

CHANGE DEFAULT

SOURCE EDIT

SIGNAL ENTRY

1) Use the CURSOR or button to select “CHANGE DEFAULT” and press ENTER.

• The “STORE TO DEFAULT AREA?” will be displayed.

2) Use the CURSOR or button to select an item and press ENTER.

Items to select

• YES ......... The picture parameter data of the selected signal

will be stored in the DEFAULT AREA.

• NO ........... The picture parameter data of the selected signal

will not be stored in the DEFAULT AREA.

STORE TO DEFAULT AREA?

( DEFAULT No. ✻ )

• If the “SIGNAL ENTRY” list will be displayed, this completes the CHANGE DEFAULT mode.

• To end the “SIGNAL ENTRY” list, go on to Step 5.

m When selecting “SOURCE EDIT”

This feature allows you to change various parameters of the source on the selected line. This can be done to the current projected signal as well as not projected source.

NOTE: The setting INPUT TERMINAL cannot be done to the current projected signal.

To do this, proceed as follows:

1) Use the CURSOR or button to select “SOURCE EDIT” and then press ENTER.

• The “SOURCE INFORMATION” screen will be displayed.

• The “SOURCE INFORMATION” screen will be also displayed by pressing the INFO button on the service remote while the SIGNAL ENTRY is displayed.

2) Use the CURSOR or button to select the item and then press ENTER.

• The selected setting screen is displayed.

YES NO

SIGNAL ENTRY

NEW ENTRY ENTRY COPY ENTRY MOVE ENTRY DELETE DATA COPY CHANGE DEFAULT

SOURCE EDIT

P01/03 SOURCE INFORMATION

NAME ✻✻✻✻✻✻✻✻

INPUT TERMINAL INPUT A INPUT SOURCE RGB VIDEO MODE RGB FREQUENCY FH=✻✻✻.✻✻kHz

FV=✻✻.✻✻Hz

SYNC POLARITY HD(–) VD(+)

mWhen selecting "INPUT TERMINAL"

You can select the input terminal for the registered signal. This feature is useful when you need to change the input terminal due to adding optional equipment.

NOTE: This setting cannot be done to the current projected signal.

To do this, proceed as follows:

1) Use the CURSOR buttons to select “INPUT TERMINAL” and then press ENTER.

• The “INPUT TERMINAL SELECT” menu will be displayed.

When used in the stand alone operation:

Use the CURSOR or button to select an input slot from three slots: INPUT A, INPUT B, and INPUT C, and press ENTER.

• The "SIGNAL ENTRY" screen is displayed.

Items to select

• INPUT A ..............Standard installed terminal

• INPUT B ..............Optional board terminal

• INPUT C ..............Optional board terminal

SIGNAL ENTRY

P01/03 SOURCE INFORMATION NAME ✻✻✻✻✻✻✻✻

INPUT TERMINAL INPUT A

INPUT SOURCE RGB VIDEO MODE RGB FREQUENCY FH=✻✻✻.✻✻kHz

FV=✻✻.✻✻Hz

SYNC POLARITY HD(–) VD(+)

INPUT TERMINAL SELECT

INPUT A

INPUT B INPUT C

When used with a single Switcher ISS-6020/ISS6020G:

Use the CURSOR or button to select the desired slot number "1" through "10 (0)" of the Switcher and press ENTER.

• The "SIGNAL ENTRY" screen is displayed.

When used with two or more Switchers ISS-6020/ ISS-6020G:

Use the CURSOR or button to select the master slot number "1" through "10 (0)" first from the master menu, then select the slave slot number "1" through "10 (0)" from the slave menu and press ENTER.

• The "SIGNAL ENTRY" screen is displayed.

• For changing parameters of the setting feature, see pages 35 to 43.

MASTER

SLOT–01

SLOT–02 SLOT–03 SLOT–04 SLOT–05 SLOT–06 SLOT–07 SLOT–08 SLOT–09 SLOT–10

MASTER

SLOT–01

SLOT–02 SLOT–03 SLOT–04 SLOT–05 SLOT–06 SLOT–07 SLOT–08 SLOT–09 SLOT–10

SLAVE

SLOT–01

SLOT–02 SLOT–03 SLOT–04 SLOT–05 SLOT–06 SLOT–07 SLOT–08 SLOT–09 SLOT–10

SIGNAL ENTRY

5 To complete the signal entry, press the END button.

• Whenever the END button is pressed, the menus will sequence in this order: “ADJUST” menu → Source screen.

• When your passcode is in effect, the “RETURN USER MODE?” screen will be displayed. If this happens, use the CURSOR or button to select either “YES” or “NO” and press ENTER.

Items to select

• YES ......... When you try to enter the ADJUST mode

the next time, you will need to re-enter your passcode.

• NO ........... When you try to enter the ADJUST mode

the next time, you will not need to re-enter your passcode.

RETURN USER MODE?

YES NO

Checking and Setting Various Parameters

Parameters of the signal currently projected can be displayed. For changing parameters of the other registered signals, perform on the SIGNAL ENTRY screen. See pages 36 to 43. To view or change the parameters, proceed as follows: 1 Press the ADJUST button.

The “ADJUST” menu will be displayed.

NOTE: The projector may ask you to enter your passcode.

• See page 68 for Passcode explanation.

2 Press the INFO button.

• The “SOURCE INFORMATION” screen will be displayed.

• The “SOURCE INFORMATION” screen will be displayed also when you exit the “SIGNAL ENTRY” screen.

3 Check and / or set the various parameters of the signal currently

projected. The menu items you can set are NAME, SYNC CONTROL, COUNTER, DISPLAY TIME, SOURCE LOCK, AKB, POSITION, FONT, APERTURE, and SYNC TERMINATION. See the following pages for an explanation of each setting.

SIGNAL ENTRY

– ADJUST –

1 / SIGNAL ENTRY

2 / FOCUS 3 / ALIGNMENT 4 / CONVERGENCE 5 / KELVIN 6 / R,G,B GAIN 7 / PASSCODE 8 / OPTION 9 / REF.ADJUST

P01/03 SOURCE INFORMATION NAME ✻✻✻✻✻✻✻✻

INPUT TERMINAL INPUT A INPUT SOURCE RGB VIDEO MODE RGB FREQUENCY FH=✻✻✻.✻✻kHz

SYNC POLARITY HD(–) VD(+)

P03/03 SOURCE INFORMATION POSITION WIDE

FONT NORMAL APERTURE

SYNC TERMINATION 75Ω AFC NORMAL

MANUAL LEVEL1

§ ©

FV=✻✻.✻✻Hz

§ ©

P02/03 SOURCE INFORMATION SYNC CONTROL AUTO

COMP. COUNTER ✻✻✻✻✻ D I S P L A Y T I M E ✻✻✻✻: ✻✻ S O U R C E LOCK OFF AKB OFF G-Y MATRIX

SIGNAL ENTRY

m Setting “NAME”

This function is used to change a user name that has previously been entered. To do this, proceed as follows:

1) Use the CURSOR buttons to select “NAME” and then press ENTER.

• The “NAME INPUT” screen will be displayed.

2) Input a new source name by selecting one character at a time with the INPUT buttons 1 through 10 and by moving the cursor with the CURSOR button. Only after completely finishing the selection of the characters, press ENTER.

• If you have made an error, use the CURSOR button and

reenter the correct letter or number. To delete one character, move the under bar to the character to be deleted and then press the NORMAL button. To delete all the entered name, hold down the CTL button then press the NORMAL button.

• The above is the same procedure of the signal entry. See

page 27 for more details.

• The screen will return to the “SOURCE INFORMATION”

screen.

P01/03

NAME

INPUT TERMINAL INPUT SOURCE

 VIDEO MODE

FREQUENCY  SYNC POLARITY

SOURCE INFORMATION

NAME INPUT

––––––––

∗∗∗∗∗∗∗∗

 INPUT A RGB RGB FH = KHz

FV = Hz HD(-) VD(+)  

•

∗∗∗∗∗∗

•

∗∗∗∗∗∗

m Setting “SYNC CONTROL”

This function is used to select the detection method of the sync signal for an RGB signal. To do this, proceed as follows:

1) Use the CURSOR buttons to select “SYNC CONTROL” and then press ENTER.

• The “SYNC CONTROL” menu will be displayed.

2) Use the CURSOR or button to select either “AUTO”, “G-SYNC”, or “TRI-SYNC” and press ENTER.

• The screen will return to the “SOURCE INFORMATION”

screen.

• When “AUTO” is selected, the sync type will be displayed.

• Select “AUTO” in normal operation.

On-screen display

• AUTO----- Detects automatically a composite or HV separate sync signal.

• G-SYNC -- When sync on green and HV separate signals are accepted at the same time, the screen may be greenish. If this happens, select this “G-SYNC” to return to the normal screen.

• TRI-SYNC Selects a tri-sync signal (HDTV signal).

P02/03 SOURCE INFORMATION

SYNC CONTROL

 COUNTER DISPLAY TIME SOURCE LOCK AKB G-Y MATRIX

SYNC CONTROL

AUTO

G-SYNC TRI-SYNC 

AUTO COMP. 

∗∗∗∗∗



∗∗∗∗∗∗

OFF OFF 

m Setting “COUNTER”

This function is used to reset the number of times a signal is selected for display.

1) Use the CURSOR buttons to select the “COUNTER” and then press ENTER.

• The “COUNTER RESET?” screen will be displayed.

2) Use the CURSOR or button to select either “YES” or “NO” and then press ENTER.

• To reset the counter, select “YES”. If you do not need to

reset, select “NO”.

• The screen will return to the “SOURCE INFORMATION”

screen.

SIGNAL ENTRY

P02/03 SOURCE INFORMATION

SYNC CONTROL 

COUNTER

DISPLAY TIME SOURCE LOCK AKB G-Y MATRIX

COUNTER RESET?

YES NO

AUTO COMP.

∗∗∗∗∗



∗∗∗∗∗∗

OFF OFF 

m Setting “DISPLAY TIME”

This function is used to reset the time of signal display.

1) Use the CURSOR buttons to select “DISPLAY TIME” and then press ENTER.

• The “DISPLAY TIME RESET?” screen will be displayed.

2) Use the CURSOR or button to select either “YES” or “NO” and then press ENTER.

• To reset the timer, select “YES”. If you do not need to

reset, select “NO”.

• The screen will return to the “SOURCE INFORMATION”

screen.

P02/03 SOURCE INFORMATION

SYNC CONTROL  COUNTER

DISPLAY TIME

SOURCE LOCK



AKB G-Y MATRIX

DISPLAY TIME RESET?

YES NO

AUTO COMP. 

∗∗∗∗∗



∗∗∗∗∗∗

OFF OFF 

SIGNAL ENTRY

m Setting “SOURCE LOCK”

This function is used to stop the projector’s automatic signal discrimination of various RGB signals. Set the lock control to the ON position when connecting an intermittent or low quality signal.

1) Use the CURSOR buttons to select “SOURCE LOCK” and press ENTER.

• The “SOURCE LOCK CONTROL” menu will be displayed.

2) Use the CURSOR or button to select either “OFF” or “ON” and press ENTER.

• The screen will return to the “SOURCE INFORMATION”

screen.

• Select “OFF” in normal operation.

Items to select

• ON ........... Activates the projector’s automatic signal discrimi-

nation of RGB signals.

• OFF.......... Deactivates the projector’s automatic signal

discrimination of RGB signals.

P02/03 SOURCE INFORMATION

SYNC CONTROL  COUNTER DISPLAY TIME

SOURCE LOCK

AKB G-Y MATRIX

SOURCE LOCK CONTROL

OFF

AUTO COMP. 

∗∗∗∗∗



∗∗∗∗∗∗

OFF OFF 

m Setting “AKB”

This function is used to activate the auto white balance control.

1) Use the CURSOR buttons to select “AKB” and then press ENTER.

• The “AKB CONTROL” menu will be displayed.

2) Use the CURSOR or button to select either “OFF” or “ON” and then press ENTER.

• The screen will return to the “SOURCE INFORMATION”

screen.

NOTE: When “ON” is selected, the AKB detection signal will appear on the top of the screen. If you wish to remove it, select “OFF”.

• If the projector is used on the AKB OFF for an extended

period, it could affect the white balance settings. To avoid this, set AKB to ON periodically.

P02/03 SOURCE INFORMATION

SYNC CONTROL  COUNTER DISPLAY TIME SOURCE LOCK

AKB

G-Y MATRIX

AKB CONTROL

OFF

ON



AUTO COMP. 

∗∗∗∗



∗∗∗∗∗∗

OFF OFF 

m Setting “G-Y MATRIX”

This function is used to set a matrix ratio for a COMPONENT signal. Note that this function is not available unless a COMPONENT signal is accepted. To do this, proceed as follows:

1) Use the CURSOR buttons to select “G-Y MATRIX” and press ENTER.

• The “G-Y MATRIX” menu will be displayed.

2) Use the CURSOR or button to select an item and press ENTER.

• The screen will return to the “SOURCE INFORMATION”

screen.

Items to select

•HD -------------For an HDTV signal

•NTSC 1-3------For a DVD signal

SIGNAL ENTRY

P02/03 SOURCE INFORMATION

SYNC CONTROL  COUNTER DISPLAY TIME SOURCE LOCK AKB

G-Y MATRIX



G-Y MATRIX

NTSC1 NTSC2 NTSC3

AUTO COMP. 

∗∗∗∗



∗∗∗∗∗∗

OFF OFF 

SIGNAL ENTRY

m Selecting “POSITION”

This function is used to select the vertical area mode for the “POSITION-SHIFT” adjustment. To do this, proceed as follows:

1) Use the CURSOR buttons to select “POSITION” and then press ENTER.

• The “POSITION” menu will be displayed.

2) Use the CURSOR or button to select either “WIDE” or “NARROW” and then press ENTER.

• The screen will return to the “SOURCE INFORMATION”

screen.

• Select “WIDE” in normal operation.

Items to select

• WIDE ....... Adjustment area is wide.

• NARROW. Adjustment area is narrow.

P03/03 SOURCE INFORMATION

POSITION

FONT APERTURE  SYNC TERMINATION AFC

POSITION

WIDE

NARROW

WIDE NORMAL MANUAL LEVEL1 75Ω NORMAL

NOTE: Selecting “NARROW” may solve problems caused by an interlace input signal.

m Setting “FONT”

This function is used to specify the appropriate font size to the on-screen message. To do this, proceed as follows:

1) Use the CURSOR buttons to select “FONT” and then press ENTER.

• The “FONT SIZE” menu will be displayed.

2) Use the CURSOR or button to select either “NORMAL” or “SMALL” and then press ENTER.

• The screen will return to the “SOURCE INFORMATION”

screen.

P03/03 SOURCE INFORMATION

POSITION

FONT

APERTURE  SYNC TERMINATION AFC



FONT SIZE

NORMAL

SMALL

WIDE NORMAL MANUAL LEVEL1

Ω

NORMAL

Items to select

• NORMAL . Calculates the appropriate font size with the vertical scanning lines to display the on-screen message in the appropriate size.

• SMALL .... Displays the on-screen message in the font size of

75 percent of the NORMAL size.

m Setting “APERTURE”

This function is used to correct picture edge by changing the frequency response. You can select two aperture modes: manual and auto.

1) Use the CURSOR buttons to select “APERTURE” , then press ENTER.

• The “APERTURE “ menu will be displayed.

2) Use the CURSOR or button to select “MANUAL” or “AUTO”, then press ENTER.

SIGNAL ENTRY

P03/03 SOURCE INFORMATION POSITION WIDE FONT NORMAL

APERTURE MANUAL

LEVEL 1

SYNC TERMINATION 75Ω AFC NORMAL

Items to select

• MANUAL . Selects one of the eight aperture levels.

• AUTO....... Corrects the aperture automatically according to

the horizontal frequency of the input signal.

• When "MANUAL" is selected, the "LEVEL" menu is displayed. Use the CURSOR or button to select the desired correction level.

• The screen will return to the “SOURCE INFORMATION” screen.

NOTE: The default setting is "MANUAL-LEVEL 1".

m Setting “SYNC TERMINATION”

This function is used to select the impedance of the sync signal.

1) Use the CURSOR buttons to select “SYNC TERMINATION” , then press ENTER.

• The “SYNC TERMINATION” menu will be displayed.

2) Use the CURSOR or button to select “ 75 Ω” or “Hi-Z”, then press ENTER.

• The screen will return to the “SOURCE INFORMATION”

screen.

APERTURE

MANUAL

AUTO

LEVEL

LEVEL 0

LEVEL 1

LEVEL 2 LEVEL 3 LEVEL 4 LEVEL 5 LEVEL 6

LEVEL 7

P03/03 SOURCE INFORMATION

POSITION FONT APERTURE 

SYNC TERMINATION

AFC

WIDE NORMAL MANUAL LEVEL1 75Ω NORMAL

NOTE: The default setting is “75 Ω”. This should be “75 Ω” for normal use. Select the “Hi-Z” when inputting a TTL signal.

SYNC TERMINAL

75Ω

Hi-Z

SIGNAL ENTRY

m Setting “AFC” This function is used to reduce jitter by changing time-constant of AFC of the sync generator circuit.

1) Use the CURSOR buttons to select “AFC”, then press ENTER.

• The “AFC” menu will be displayed.

2) Use the CURSOR or button to select “NORMAL” or “SLOW” , then press ENTER.

• The screen will return to the “SOURCE INFORMATION”

screen.

Items to select

• NORMAL........ Standard AFC time-constant.

• ON ................. Slows the AFC time-constant.

NOTE: The default setting is NORMAL. Although jitter will be reduced, image distortion may appear at the top of the screen if the AFC mode is set to SLOW.

P03/03 SOURCE INFORMATION POSITION WIDE FONT NORMAL APERTURE MANUAL

LEVEL 1

SYNC TERMINATION 75Ω

AFC NORMAL

AFC

NORMAL

SLOW

To complete, press the END button.

• Whenever the END button is pressed, the menus will sequence

in this order: “ADJUST” menu → Source screen

• When your passcode is in effect, the “RETURN USER

MODE?” screen is displayed. If this happens, use the CURSOR or button to select either “YES” or “NO” and press ENTER.

Items to select

• YES ......... When you try to enter the ADJUST mode the next

time, you will need to re-enter your passcode.

• NO ........... When you try to enter the ADJUST mode the next

time, you will not need to re-enter your passcode.

SIGNAL ENTRY

RETURN USER MODE?

YES NO

12345

ADJUSTMENT.

Set-Up Procedure

Before adjusting

1 Installation of the projector. 2 Connect the external equipment to the projector. 3 Turn on power to the external equipment and the projector.

• If you want to institute the use of a passcode, register the passcode. See page 69.

• Carry out the adjustments after displaying an image for 20 minutes or more.

4 Select the input signal.

• If your input signal has not been recorded, it is necessary to perform the signal entry beforehand. See page 23.

If you want to use the projector in any other configuration than the factory setting, perform the following after installation.

1) Electrical Focus Adjustment See page 45

2) Alignment Adjustment See page 49

3) Static Convergence Adjustment See page 55

4) Dynamic Convergence Adjustment See page 56

5) Color temperature & White Balance Adjustment See page 66

6) R, G, B Gain Adjustment See page 67

(only when used with the ISS-6020/ISS-6020G)

*If a wrong button is pressed accidently, an error message will appear. *Pressing the HELP button will display a brief description of the

selected function and button operation instructions.

Check and adjust again if necessary

Electrical Focus Adjustment

Adjust the focus electrically to obtain the best screen focus.

NOTE:

• The adjustment must be done to each input.

• Select the FOCUS test pattern using the TEST button on the full function remote control.

Proceed as follows: 1 Press the ADJUST button to display the “ADJUST” menu.

• The projector may ask you to enter your passcode. See page 68 for the explanation of the PASS CODE.

2 Use the CURSOR or button to highlight the “2/FOCUS”

line. Press ENTER to display the FOCUS menu. You can also select the FOCUS menu directly by pressing the INPUT “2” button.

3 Use the CURSOR or button to highlight your preferred

adjustment item. Press ENTER to display the selected adjustment screen.

• You can also select the adjustment screen directly by pressing the INPUT “1” through “4” button.

• For edge focus, you can select either “EDGE ALL” or “EDGE SEPA.” in the FOCUS EDGE mode of the OPTION menu. (See page 82).

ADJUSTMENT

– ADJUST – 1 / SIGNAL ENTRY

2 / FOCUS

3 / ALIGNMENT 4 / CONVERGENCE 5 / KELVIN 6 / R,G,B GAIN 7 / PASSCODE 8 / OPTION 9 / REF.ADJUST

Items to select

• CENTER......... The focus adjustment for the center of the

screen (each CRT).

• EDGE ALL...... The focus adjustment for the edge area of the

screen (all CRTs).

• EDGE SEPA. .. The focus adjustment for the edge area of the

screen (each CRT).

• CORNER........ The focus adjustment for the corner of the

screen (each CRT).

NOTE:

• The adjustment screen can also be displayed by pressing the

FOCUS button on the full function remote control. The FOCUS button rotates the adjustment screen in the above order.

– FOCUS –

1 / CENTER

2 / EDGE ALL 3 / EDGE SEPA. 4 / CORNER

ADJUSTMENT

FOCUS

- CENTER - CRT - R -

+10%

4 Press the R, G, and B button to project the CRT beam to be

adjusted.

• You can turn on or off each CRT beam (R, G, and B)separately.

NOTE:

• The CENTER, EDGE SEPA. ,and CORNER focus adjustment

should be performed for each CRT separately.

• The EDGE ALL focus adjustment affects all the three CRTs at

the same time.

5 Hold down the CTL button then select the CRT you wish to

adjust with the R, G, and B button.

• The display of the corresponding CRT will change from one CRT to another.

NOTE:

• You do not need to select the CRT color for the EDGE ALL

focus.

• Always be aware of what color the on-screen CRT display is

showing (R, G, B) when “CENTER”, “EDGE SEPA.”, or “CORNER” is selected. If that color’s test pattern is turned off, any adjustment to that color will display the “THIS COLOR IS NOT APPLICABLE” message.

6 Use the CURSOR buttons to adjust the focus.

m When selecting “CENTER”

• Pressing the or button increases the control levels of the center focus. (The gauge mark in the scale moves to the right.)

• Pressing the or button decreases the control levels of the center focus. (The gauge mark in the scale moves to the left.)

To switch to the "EDGE ALL" or "EDGE SEPA." mode: press and hold CTL, then press CURSOR button.

FOCUS

- EDGE ALL -

SCREEN -TOP-

+10%

m When selecting “EDGE ALL”/”EDGE SEPA.”

FOCUS

- CORNER - CRT - R - SCREEN - BR -

+10%

1) Press and hold the CTL button then press any one of the CURSOR buttons to select the position to be adjusted. (The marker on the selected side will turn to a solid color.)

CTL + (Top) CTL + (Right) CTL + (Bottom) CTL + (Left)

• To switch to Bottom from Top, press and hold CTL, then press

CURSOR twice.

• To switch to Top from Bottom, press and hold CTL, then press

CURSOR twice.

• To switch to Left from Right, press and hold CTL, then press

CURSOR twice.

• To switch to Right from Left, press and hold CTL, then press

CURSOR twice.

2) Use the CURSOR buttons to adjust the focus.

• Pressing the or button increases the control levels of the

edge focus. (The gauge mark in the scale moves to the right.)

• Pressing the or button decreases the control levels of the

edge focus. (The gauge mark in the scale moves to the left.)

3) To switch to the CENTER screen, use the CTL and CURSOR

buttons as follows:

• To switch to CENTER from Top, press and hold CTL, then

press CURSOR .

• To switch to CENTER from Bottom, press and hold CTL, then

press CURSOR .

• To switch to CENTER from Right, press and hold CTL, then

press CURSOR .

• To switch to CENTER from Left, press and hold CTL, then

press CURSOR .

ADJUSTMENT

FOCUS

- EDGE SEPARATE - CRT - R -

SCREEN -TOP-

+10%

m When selecting “CORNER”

• Press and hold the CTL button then press any one of the

CURSOR buttons to select the position to be adjusted. (The marker on the selected side will turn to a solid color.)

CTL + ......

TR (Top right) BR (Bottom right ) TL (Top left ) BL (Bottom left)

• Use the CURSOR buttons to adjust the focus.

Pressing the or button increases the control levels of the corner focus. (The guage mark in the scale moves to the right.) Pressing the or button decreases the control levels of the corner focus. (The guage mark in the scale moves to the left.)

ADJUSTMENT

7Repeat steps 4 to 6 for the other CRTs if necessary. 8 To end this adjustment, press the END button.

• Whenever the END button is pressed, the menu will sequence in this order: “FOCUS” menu → “ADJUST” menu → Source screen

• If the “RETURN USER MODE?” menu appears, use the CURSOR or button to select either “YES” or “NO” and then press ENTER. This will exit the ADJUST mode.

Items to select

• YES ......... When you try to enter the ADJUST mode the next

time, you will need to re-enter your passcode.

• NO ........... When you try to enter the ADJUST mode the next

time, you will not need to re-enter your passcode.

NOTE: The center focus for the Blue CRT is pre-adjusted so that the best white uniformity can be obtained at the gauge center (0%). For this reason, it has been set at the factory to be slightly out of focus. Therefore you should not perform the center focus adjustment to the Blue CRT with the remote control.

RETURN USER MODE?

YES NO

Alignment Adjustment

Correct the horizontal and vertical error for the projected image.

NOTE: Select the CROSS-COARSE test pattern using the TEST button on the full function remote control.

ADJUSTMENT

Proceed as follows: 1 Press the ADJUST button to display the “ADJUST” menu.

• The projector may ask you to enter your passcode. See page 68 for the explanation of the PASSCODE.

2 Use the CURSOR or button to highlight the “3/ALIGN-

MENT” line. Press ENTER to display the “ALIGNMENT” menu. You can also select the “ALIGNMENT” menu directly by pressing the INPUT “3” button.

3 Use the CURSOR or button to select the preferred item.

Press ENTER. You can also select the alignment item directly by pressing an INPUT button.

• The selected adjustment screen will be displayed. See page 50 and 54 for the explanation of the selected adjustment.

Items to select

• TILT SKEW .......... Adjusts the tilt and the skew

• BOW....................Adjusts the horizontal and vertical bow

• AMPLITUDE ........ Adjusts the horizontal and vertical ampli-

tude of the projected image

• LINEARITY .......... Adjusts the horizontal and vertical linearity

• KEY-STONE ......... Adjusts the horizontal and vertical keystone

• PIN-CUSHION .....Adjusts the horizontal and vertical pincushion

• LINEAR-BAL........Adjusts the horizontal and vertical linearity

balance

• KEY-BALANCE.....Adjusts the horizontal and vertical keystone

tilt balance

• PIN-BALANCE .....Adjusts the horizontal and vertical pincush-

ion bow balance

• LINE DIST............ Adjusts S shaped distortion of vertical and

horizontal lines

• R,G,B POINT........ Adjusts the horizontal and vertical line in

detail using a intersections on the CROSSCOARSE pattern as a reference point

– ADJUST – 1 / SIGNAL ENTRY 2 / FOCUS

3 / ALIGNMENT

4 / CONVERGENCE 5 / KELVIN 6 / R,G,B GAIN 7 / PASSCODE 8 / OPTION 9 / REF.ADJUST

– ALIGNMENT –

01 / TILT,SKEW

02 / BOW 03 / AMPLITUDE 04 / LINEARITY 05 / KEY-STONE 06 / PIN-CUSHION 07 / LINEAR-BAL 08 / KEY-BALANCE 09 / PIN-BALANCE 10 / LINE DIST 11 / R,G,B POINT

NOTE: You can also select adjustments directly using buttons on the full function remote control. If you are in the CONVERGENCE mode (see page 56), press and hold down the CTL button then press the G button. This will bring you to the ALIGNMENT adjustment screen. To select the “LINEAR-BAL”, “KEY-BALANCE”, or “PIN-BALANCE”, or “LINE DIST”. alignment, press and hold down the CTL button then press the LINEAR,KEYSTN, PINCUS, or BOW button respectively.

ADJUSTMENT

4 Press the R, G, and B buttons to display only the Green pattern.

• You can turn on or off each CRT beam (R, G or B) separately.

• To access the CONVERGENCE screen (see page 56), press and hold down the CTL button then press the R or B button.

5 Use the CURSOR buttons to adjust the alignment of the pro-

jected pattern.

• The CURSOR or button increases or decreases the horizontal level. The CURSOR or button increases or decreases the vertical level.

ALIGNMENT

- TILT,SKEW -

+10%H

−90%V

ALIGNMENT

- TILT,SKEW -

m Adjusting LINE DISTORTION

1) Select the “10/LINE DIST.” item then press ENTER.

• The “LINE DIST.” menu is displayed.

2) Use the CURSOR or buttons to select the item and press ENTER to display the selected adjustment screen. You can

also select the item directly by pressing the corresponding INPUT number button.

• The selected adjustment screen is displayed.

• The adjustment screen can also be displayed by holding and pressing the CTL, then the BOW button on the full function remote control. Each press of the BOW button with pressed CTL toggles the adjustment screen between CENTER, EDGE and BIQUAD.

ABNORMAL CORRECTION DATAV

During alignment or convergence adjustment, if the projector acknowledges that your adjustment is overcorrected, the “ABNORMAL CORRECTION DATA” message appears. The data is cancelled at that moment. If this happens, reduce the total amount of the current adjustment data.

+10%

-LINE DIST.-

1 / CENTER

2 / EDGE 3 / BIQUAD

ALIGNMENT

- LINE DIST. CENTER -

Items to select

• CENTER...............Corrects S-shaped horizontal lines distor-

tion on the screen.

• EDGE ................... Corrects S-shaped lines distortion around

the perimeter of the screen.

• BIQUAD ............... Corrects biquadratic distortion at the top

and bottom of the screen.

ADJUSTMENT

3) Use the CURSOR buttons to align the pattern. When selecting "CENTER":

• Pressing the CURSOR or button increases the level.

Pressing the CURSOR or button decreases the level.

When selecting "EDGE":

• Pressing the CURSOR or button corrects the vertical lines. Pressing the CURSOR or button corrects the horizontal lines.

When selecting “BIQUAD”:

• Pressing the CURSOR or increases the level.

• Pressing the CURSOR or decreases the level. To switch to the adjustment position, press and hold CTL and then press CURSOR or button.

ALIGNMENT

- LINE DIST. EDGE -

H V

ALIGNMENT

- LINE DIST. BIQUAD SCREEN -TOP-

0% 0%

m Adjusting R,G,B POINT

NOTE:

• The R,G,B POINT adjustments should only be done if necessary. Over adjusting them may cause the picture distortion.

• The alignment adjustment affects three CRTs at the same time while the convergence adjustment needs to be performed for each CRT (R and B) separately.

1) Select "11/R,G,B POINT" from the "ALIGNMENT"menu and press ENTER to display the "R,G,B POINT" menu. For dynamic convergence, select "9/POINT" from the "CONVERGENCE" menu and press ENTER to display the "POINT" menu.

2) Use the CURSOR or button to select the item and press ENTER to display the selected adjustment screen. You can also

select the item directly by pressing the corresponding INPUT number button.

• The "CROSS-COARSE" test pattern will be automatically

displayed.

• The R,G,B POINT screen in the alignment mode or the

POINT adjustment screen in the convergence mode can be also displayed by pressing the POINT button on the full function remote control. The POINT button rotates the adjustment screen in the following order: COARSE, MEDIUM, FINE.

-R,G,B POINT-

1/COARSE

2/MEDIUM 3/FINE

RGB POINT

- COARSE -

RGB POINT

- COARSE -

ADJUSTMENT

Items to select

• COARSE ..............Coarse adjustment. Number of adjust-

ment zones is 3 x 3.

• MEDIUM..............Number of adjustment zones is 7 x 7.

• FINE.....................Fine adjustment. Number of adjustment

points is 13 x 16.

3) Use the CURSOR or buttons to move the cursor mark to the point to be adjusted.

• Pressing the CURSOR button moves the cursor to the right. Pressing the CURSOR button moves the cursor to the left.

Pressing the CURSOR button moves the cursor to the top. Pressing the CURSOR button moves the cursor to the

bottom.

4) For alignment, hold down the CTL button, then use the CURSOR buttons to align the pattern. For convergence, hold down the CTL button and then use the CURSOR buttons to align the Red or Blue pattern with the Green pattern.

NOTE: For more accurate convergence correction on edges, perform the amplitude and linearity adjustments before the POINT convergence adjustment.

When the adjustment area frame is a box type.

When FINE is selected, the adjustment area frame is not displayed.

When the adjustment area frame is a box with one side open.

: adjustment area frame

: adjustment

6To end this adjustment, press the END button.

• Whenever the END button is pressed, the menus will sequence in this order: “ALIGNMENT” menu → “ADJUST” menu → Source screen

• If the “RETURN USER MODE?” menu appears, use the CURSOR or button to select either “YES” or “NO” and then press ENTER. This will exit the ADJUST mode.

Items to select

• YES ......... When you try to enter the ADJUST mode again,

you will need to re-enter your passcode.

• NO ........... When you try to enter the ADJUST mode again,

you will not need to re-enter your passcode.

RETURN USER MODE?

YES NO

Alignment Adjustment Items

ADJUSTMENT

TILT

Adjust horizontal center line.

Vertical BOW

Adjust horizontal center line bow.

Vertical AMPLITUDE

Adjust vertical height of image.

SKEW

Adjust vertical center line.

Horizontal BOW

Adjust vertical center line bow.

Horizontal AMPLITUDE

Adjust horizontal size of image.

Vertical LINEARITY

Adjust top and bottom linearity.

Vertical KEYSTONE

Adjust top and bottom keystone error.

Horizontal LINEARITY

Adjust left and right linearity.

Horizontal KEYSTONE

Adjust left and right keystone error.

ADJUSTMENT

Alignment Adjustment Items

Vertical PINCUSHION

Equalize top and bottom pincushion error.

Vertical LINEAR-BALANCE

Equalize top and bottom linearity balance error.

Vertical KEY-BALANCE

Equalize top and bottom keystone balance error.

Horizontal PINCUSHION

Equalize left and right pincushion error.

Horizontal LINEAR-BALANCE

Equalize left and right linearity balance error.

Horizontal KEY-BALANCE

Equalize left and right keystone balance error.

Vertical PIN-BALANCE

Equalize top and bottom pincushion balance error.

LINE DIST. CENTER

Correct S-shaped horizontal line

LINE DIST. BIQUAD

Correct biquadratic distortion

Horizontal PIN-BALANCE

Equalize left and right pincushion balance error.

Vertical LINE DIST. EDGE

Correct S-shaped horizontal line

Vertical POINT

Adjust the point peak vertically

Horizontal LINE DIST. EDGE

Correct S-shaped vertical line

Horizontal POINT

Adjust the point peak horizontally

Marker up

Marker down

Static Convergence Adjustment

Adjust the red and blue CRT images to position them over the green test pattern (center portion only).

NOTE: The static convergence adjustment should be performed for each CRT (R and B) separately. Carry out the adjustment after displaying an active image for 20 minutes or more.

Proceed as follows: 1 Press the OPERATE button.

• The “OPERATE” menu is displayed.

2 Use the CURSOR or button to highlight the “6/STATIC”

line. Press ENTER to display the STATIC adjustment. You can also select the STATIC adjustment screen directly by pressing the INPUT “6” button.

• The CROSS-HAIR test pattern will be automatically displayed.

NOTE: When you are in the ADJUST mode, selecting the STATIC mode will not automatically select the CROSS-HAIR test pattern. Reselect the pattern using the TEST button. NOTE: The “STATIC” adjustment can be also displayed by pressing the STATIC button on the user or full function remote control.

ADJUSTMENT

– OPERATE – 1 / PICTURE 2 / POSITION 3 / SOUND 4 / INPUT SELECT 5 / SOURCE INFO

6 / STATIC

7 / CLOSED CAPTION 8 / TIMER

3 Press the R or B button to display the pattern to be aligned with

the Green pattern.

• You can turn on or off each CRT beam (R and B) separately.

4 Hold down the CTL button then select the CRT you wish to

adjust with the R and B buttons.

NOTE: Always be aware of what color the on-screen CRT display is showing (R, G, B). If that color’s test pattern is turned off, any adjustment to that color will display the “THIS COLOR IS NOT APPLICABLE” message.

5 Align the center of the Red or the Blue pattern with the center of

the Green pattern (reference color) using the CURSOR buttons.

• The CURSOR or button moves the pattern left or right. The CURSOR or button moves the pattern up or down.

6 Repeat steps 3 to 5 for the other CRTs if necessary.

7 To end this adjustment, press the END button.

• Whenever the END button is pressed, the menus will sequence in this order: “OPERATE” menu → Source screen

CONVERGENCE

- STATIC -

CRT - R -

H V

Green

`10% 110%

Red or Blue

ADJUSTMENT

Dynamic Convergence Adjustment

Corrects the horizontal and vertical error for each color and align the red and blue to the green.

NOTE:

• The dynamic convergence adjustment should be performed for each CRT (R and B) separately.

• Select the CROSS-COARSE test pattern using the TEST button on the full function remote control.

Proceed as follows: 1 Press the ADJUST button to display the “ADJUST” menu.

• The projector may ask you to enter your passcode. See page 68 for the explanation of the PASSCODE.

2 Use the CURSOR or button to highlight the “4/CONVER-

GENCE” line. Press ENTER to display the “CONVERGENCE” menu. You can also select the “CONVERGENCE” menu directly by pressing the INPUT “4” button.

– ADJUST – 1 / SIGNAL ENTRY 2 / FOCUS 3 / ALIGNMENT

4 / CONVERGENCE

5 / KELVIN 6 / R,G,B GAIN 7 / PASSCODE 8 / OPTION 9 / REF.ADJUST

3 Use the CURSOR or button to select the preferred item and

then press ENTER. You can also select directly the dynamic convergence item by pressing an INPUT button.

• The selected adjustment will be displayed. See pages 57 to 65 for the explanation of the selected adjustment.

NOTE:

• You can also select adjustments directly using buttons on the

full function remote control. If you are in the ALIGNMENT mode (see page 49), press and hold down the CTL button then press the R or B button. This will bring you to the CONVERGENCE adjustment screen. To select “LINEAR-BAL” convergence, press and hold down the CTL button then press the LINEAR button.

• To select “LINE DIST.” convergence, press and hold down the

CTL button then press the BOW button.

4 Press the R or B button to display the CRT beam to be aligned

with the Green pattern.

• You can turn on or off each CRT beam (R and B) separately.

– CONVERGENCE –

1 / TILT,SKEW

2 / BOW 3 / AMPLITUDE 4 / LINEARITY 5 / KEY-STONE 6 / PIN-CUSHION 7 / LINEAR-BAL 8 / LINE DIST. 9 / POINT 10/ PHASE

CONVERGENCE

- TILT,SKEW - CRT - R -

+10%

ABNORMAL CORRECTION DATAV

ADJUSTMENT

5 Hold down the CTL button then select the CRT you wish to

adjust with the R and B buttons.

NOTE: Always be aware of what color the on-screen CRT display is showing (R, B). If that color’s test pattern is turned off, any adjustment to that color displays the “THIS COLOR IS NOT APPLICABLE” message.

• To access the ALIGNMENT screen (see page 49), press and hold down the CTL button then press the G button.

6 Align the Red or the Blue pattern with the Green pattern using

the CURSOR buttons.

• The CURSOR button or increases or decreases H level. The CURSOR button or increases or decreases V level. The following are the description of the KEYSTONE, PINCUSHION, LINEAR-BALANCE , LINE DIST.and POINT adjustment.

CONVERGENCE

- TILT,SKEW - CRT - R -

+10%H

−90%V

m KEYSTONE, PINCUSHION, and LINEAR-BALANCE

• Press and hold the CTL button then press any one of the CURSOR buttons to select the position to be adjusted.

CTL + ....

• Use the CURSOR buttons to correct the error.

m Adjusting LINE DISTORTION

1) Select the “8/LINE DIST.” item then press ENTER.

• The “LINE DIST.” menu is displayed.

2) Use the CURSOR or buttons to select the item and press ENTER to display the selected adjustment screen. You can

also select the item directly by pressing the corresponding INPUT number button.

• The selected adjustment screen is displayed.

Items to select

• CENTER...............Corrects S-shaped horizontal lines distor-

• EDGE ................... Corrects S-shaped lines distortion around

• BIQUAD ............... Corrects biquadratic distortion at the top

(Top) (Bottom) (Right) (Left)

tion on the screen. the perimeter of the screen. and bottom of the screen.

CONVERGENCE

- KEY - STONE - CRT - R -

SCREEN -TOP-

+10%

-LINE DIST.-

1 / CENTER

2 / EDGE 3 / BIQUAD

ADJUSTMENT

3) Use the CURSOR buttons to align the pattern. When selecting "CENTER":

• Pressing the CURSOR or button increases the level.

Pressing the CURSOR or button decreases the level.

To switch to the "EDGE" screen, press and hold the CTL, then

press CUSOR or button.

When selecting "EDGE":

• Pressing the CURSOR or button increases the level.

• Pressing the CURSOR or button decreases the level.

To switch another screen, press and hold the CTL, then press

CUSOR or button.

When selecting "BIQUAD":

• Pressing the CURSOR or button increases the level.

• Pressing the CURSOR or button decreases the level.

To switch to the adjustment position, press and hold CTL and

then press CURSOR or button.

CONVERGENCE

- LINE DIST. CENTER CRT –R–

CONVERGENCE

- LINE DIST. EDGE CRT –R–

SCREEN –TOP–

CONVERGENCE

- LINE DIST. BIQUAD CRT –R–

SCREEN –TOP–

m Adjusting POINT

NOTE:

• The POINT adjustments should only be done if necessary. Over adjusting them may cause the picture distortion.

• The convergence adjustment needs to be performed for each CRT (R and B) separately.

1) Select "9/POINT" from the "CONVERGENCE"menu and press ENTER to display the "POINT" menu. For alignment, select "11/R,G,B POINT" from the "ALIGNMENT" menu and press ENTER to display the "R,G,B POINT" menu.

2) Use the CURSOR or button to select the item and press ENTER to display the selected adjustment screen. You can also

select the item directly by pressing the corresponding INPUT number button.

• The "CROSS-COARSE" test pattern will be automatically

displayed.

• The POINT convergence screen can be also displayed by

pressing the POINT button on the full function remote control. The POINT button rotates the adjustment screen in the following order: COARSE, MEDIUM, FINE.

Items to select

• COARSE .................Coarse adjustment. Number of adjust-

ment zones is 3 x 3.

• MEDIUM ................Number of adjustment zones is 7 x 7.

• FINE .......................Fine adjustment. Number of adjustment

points is 13 x 16.

ADJUSTMENT

– POINT –

1 / COARSE

2 / MEDIUM 3 / FINE 4 / ACAT

POINT

- COARSE - CRT- R - 

3) Use the CURSOR or buttons to move the cursor mark to the point to be adjusted.

• Pressing the CURSOR button moves the cursor to the right. Pressing the CURSOR button moves the cursor to the left.

Pressing the CURSOR button moves the cursor to the top. Pressing the CURSOR button moves the cursor to the

bottom.

NOTE: For more accurate convergence correction on edges, perform the amplitude and linearity adjustments before the POINT convergence adjustment.

When the adjustment area frame is a box type.

When FINE is selected, the adjustment area frame is not display.

When the adjustment area frame is a box with one side open.

: adjustment area frame : adjustment point

ADJUSTMENT

mAdjusting POINT ACAT

This feature automatically corrects convergence for overall screen adjusting 13 convergence points on R and B CRT respectively.

Before adjusting

• To improve accuracy on convergence correction, you must first adjust the convergence phase and the cursor phase for the best

image.

• You can also correct the static convergence using ACAT feature. For more accurate ACAT convergence correction, first perform

the static convergence using STATIC feature on OPERATE menu or pressing the STATIC button on the remote control.

• You must adjust the convergence to all the 13 points because ACAT feature calculates all the adjustment values on the entire screen based on the adjustments values of 13 points on the screen.

• If convergence points on the edges go out of screen, reduce the horizontal and the vertical amplitude settings using the amplitude feature of the ALIGNMENT menu so that all the 13 convergence points can be seen on the screen. After adjusting ACAT, return the horizontal and the vertical amplitude settings to their original and store them.

• The POINT ACAT convergence adjustment is done roughly. So performing the POINT ACAT can change the convergence adjustment settings even if you finely adjust the convergence adjustment.

Proceed as follows:

1) Use the CURSOR or button to select the “4/ACAT” item and then press ENTER. You can also select “ACAT” item

directly by pressing an INPUT “4” button.

• The ACAT adjustment screen will be displayed.

• You can also select the ACAT adjustment screen directly by

pressing and holding CTL and pressing POINT button on the full function remote control.

ADJUSTMENT

-POINT1/COARSE 2/MEDIUM 3/FINE

4/ACAT

2) Hold down the CTL button then press the R or B button to select the CRT you wish to adjust.

3) Use the CURSOR buttons to move the point cursor to the point where you want to adjust, then hold down the CTL button and press any one of the CURSOR buttons to align a point of intersection of the Red or the Blue pattern with a point of intersection of the Green pattern (reference color).

• Hold down the CTL button and press the CURSOR or

to move the point cursor on the selected CRT color horizontally.

• Hold down the CTL button and press the CURSOR or

to move the point cursor on the selected CRT color vertically.

4) After adjusting all the points, press the ENTER button.

• The projector automatically corrects the convergence of the

whole screen.

POINT

-ACATCRT-R-

R or B

▲

NOTE:

• The POINT ACAT adjustment may be required two or three times to improve accuracy depending on the installation condition.

• There may be some cases where you cannot get completely corrected convergence on the edges of the screen. If this happens, perform convergence adjustments other than POINT ACAT.

• If you decreased the horizontal or/and vertical amplitude and then performed the POINT ACAT adjustment, return the adjustment to its previous state.

ADJUSTMENT

m Adjusting PHASE

This adjustment corrects the phase of convergence wave forms.

NOTE: Since the projector has been pre-adjusted for the optimal phase adjustments at the factory, further adjustment should not be required in normal operation. In some cases, carrying this adjustment causes convergence to change.

1) Select "10/PHASE" and press ENTER to display the phase adjustment screen.

• The CROSS-COARSE test pattern will be automatically displayed and the adjustments will be cancelled. You can also display the adjustment screen by pressing PHASE button on the service remote control.

2) Use the CURSOR or button to adjust the convergence phase (for horizontal line). Adjust the pattern so the sharp turns at the left and right edges in the diagonal lines are equal.

3) Use the CURSOR or button to adjust the cursor phase (for vertical line). Align the vertical center line of the point cursor with the point peak.

PHASE

- CONV.,CURSOR -

CON

CUR

+20%

−20%CU

7 Repeat steps 3 to 6 for the other CRTs if necessary.

• Pressing the END button will bring you to the “CONVERGENCE” menu.

8 To exit, press END.

• Whenever the END button is pressed, the menus will sequence in this order: “CONVERGENCE” menu → “ADJUST” menu → Source screen

• If the “RETURN USER MODE?” menu appears, use the CURSOR or button to select either “YES” or “NO” and then press ENTER. This will exit the ADJUST mode.

Items to select

• YES ......... When you try to enter the ADJUST mode again,

you will need to re-enter your passcode.

• NO ........... When you try to enter the ADJUST mode again,

you will not need to re-enter your passcode.

NOTE: Adjusting the dynamic convergence may cause the static convergence settings to change. If this happens, adjust the static convergence again.

RETURN USER MODE?

YES NO

Convergence Adjustment Items

TILT

Adjust horizontal center line.

Vertical BOW

Adjust horizontal center line bow.

Vertical AMPLITUDE

Adjust top and bottom height.

ADJUSTMENT

Vertical LINEARITY

Adjust top and bottom linearity.

KEYSTONE

Adjust the selected part.

When TOP is selected

When RIGHT is selected

When BOTTOM is selected

When LEFT is selected

ADJUSTMENT

PINCUSHION

When TOP is selected

When BOTTOM is selected

LINEAR-BALANCE

Adjust the selected part.

When TOP is selected

When RIGHT is selected

When LEFT is selected

When RIGHT is selected

When BOTTOM is selected

LINE DIST. CENTER

Correct S-shaped horizontal line

LINE DIST. BIQUAD

Correct biquadratic distortion

Marker up

When LEFT is selected

LINE DIST. EDGE

Correct S-shaped horizontal line

When TOP is selected

Marker down

When BOTTOM is selected

ADJUSTMENT

Vertical POINT

Adjust the point peak vertically

PHASE CONV. PHASE

Adjust the pattern so the sharp turns at the left and right edges in the diagonal lines are equal.

Screen center

Horizontal POINT

Adjust the point peak horizontally

CURSOR PHASE

Align the vertical center line of the point cursor with the point peak.

ADJUSTMENT

Color Temperature and White Balance Adjustment

Adjusts the color temperature and the white balance.

NOTE:

• When you are in this adjustment mode, all the CRTs will be in use. The white balance adjustment should be performed for each CRT (R, G, and B) separately. The CRT beam cannot be cut-off.

Proceed as follows:

1 Press the ADJUST button to display the “ADJUST” menu.

• The projector may ask you to enter your passcode. See page 68 for the explanation of the PASSCODE.

2 Use the CURSOR or button to highlight the “5/KELVIN”

line. Press ENTER to switch to the “KELVIN.” menu. You can also select the “KELVIN.” menu directly by pressing the INPUT “5” button.

3 Use the CURSOR or button to select “COLOR TEMP.” or

“WHITE BAL.” menu.

• The “COLOR TEMPERATURE” and “WHITE BALANCE” adjustment screen can be also displayed by using the KELVIN button on the full function remote control.

m When selecting “COLOR TEMP”

Press ENTER to display the COLOR TEMPERATURE screen. Pressing or increases the color temperature. Pressing or decreases the color temperature.

• The color temperature ranges from 3200 to 9500k.

m When selecting “WHITE BAL”

Press ENTER to display the WHITE BALANCE screen.

– ADJUST – 1 / SIGNAL ENTRY 2 / FOCUS 3 / ALIGNMENT 4 / CONVERGENCE

5 / KELVIN

6 / R,G,B GAIN 7 / PASSCODE 8 / OPTION 9 / REF.ADJUST

– KELVIN –

1 / COLOR TEMP.

2 / WHITE BAL. 

COLOR

TEMPERATURE

Hold down the CTL button then select the CRT you wish to adjust with the R, G and B buttons.

Use the CURSOR buttons to adjust the white and the black level.

• The CURSOR button increases the white level. The CURSOR button decreases the white level. The CURSOR button increases the black level. The CURSOR button decreases the black level.

4 Repeat the above steps for the other CRTs if necessary. 5 To end this adjustment, press the END button.

• Whenever the END button is pressed, the menus will sequence in this order. “ADJUST” menu → Source screen

• If the “RETURN USER MODE?” menu appears, use the CURSOR or button to select either “YES” or “NO” and then press ENTER. This will exit the ADJUST mode.

Items to select

• YES ......... When you try to enter the ADJUST mode again,

you will need to re-enter your passcode.

• NO ........... When you try to enter the ADJUST mode again,

you will not need to re-enter your passcode.

3200K 9500K

WHITE BALANCE 

CRT - R -

60%WHT 10%BLK

RETURN USER MODE?

YES NO

R, G, and B Gain Adjustment

Adjusts the input level of the signal.

NOTE: This adjustment works only with the ISS-6020/ISS-6020G Switcher.

Proceed as follows: 1 Press the ADJUST button to display the “ADJUST” menu.

• The projector may ask you to enter your passcode. See page 68 for the explanation of the PASSCODE.

ADJUSTMENT

2 Use the CURSOR or button to highlight the “6/R, G, B

GAIN” line. Press ENTER to display the “R, G, B GAIN” adjustment screen. You can also select the “R, G, B GAIN” adjustment screen directly by pressing the INPUT “6” button.

3 Hold down the CTL button then select the CRT you wish to

adjust with the R, G, and B buttons.

4 Use the CURSOR buttons to adjust the level of the input signal.

• The CURSOR , button increases the input level.

• The CURSOR , button decreases the input level.

NOTE: Connect the projector and the Switcher with a oscilloscope, then adjust the CURSOR buttons to obtain a value of

0.7Vp-p of the projector input level or the Switcher output level on the oscilloscope.

– ADJUST – 1 / SIGNAL ENTRY 2 / FOCUS 3 / ALIGNMENT 4 / CONVERGENCE 5 / KELVIN

6 / R,G,B GAIN

7 / PASSCODE 8 / OPTION 9 / REF.ADJUST

R,G,B GAIN 

CRT - R -

60%

5 Repeat steps 3 and 4 for other input signals if necessary.

6 To end this adjustment, press END.

• Whenever the END button is pressed, the menus will sequence in this order: “ADJUST” menu → Source screen

• If the “RETURN USER MODE?” menu appears, use the CURSOR or button to select either “YES” or “NO” and then press ENTER. This will exit the ADJUST mode.

Items to select

• YES ......... When you try to enter the ADJUST mode again,

you will need to re-enter your passcode.

• NO ........... When you try to enter the ADJUST mode again,

you will not need to re-enter your passcode.

RETURN USER MODE?

YES NO

12345

PASSCODE.

Entering Passcode

To prevent any unauthorized operation or mis-adjustment, the projector is equipped with a passcode option. If your passcode has not been entered correctly, the “ADJUST” and “REF. ADJUST” menus will not be displayed. When the ADJUST button is pressed, and no passcode has been entered, the “PASSCODE?” screen is displayed. Enter your passcode. To do this, proceed as follows:

1 Press the ADJUST button.

• The “PASSCODE?” screen is displayed.

2 Enter the four digit passcode you have already registered by

using the “1” through “0” buttons.

1) Each time you press the INPUT button, an asterisk appears

under the “PASSCODE?” message.

2) After you have finished entering the four digit passcode, press

ENTER.

PASSCODE?

∗∗∗∗

NOTE: If you have made an error, press the NORMAL button to delete the asterisk “∗”. Then re-enter the correct passcode. To delete all the entered digits, hold down the CTL button then press the NORMAL button.

3) If the entered passcode is correct, the “ADJUST” menu is

displayed.

NOTE: If the passcode is not correct, the “WARNING DIFFERENT PASSCODE!!” message is displayed and you are required to enter the correct passcode.

3 Proceed to each adjustment and setting.

Registering Passcode

When the projector is shipped from the factory, no passcode is registered. If you want to use the passcode option, you must register a passcode. To register a new passcode, proceed as follows:

1 Press the ADJUST button.

• The “ADJUST” menu will be displayed.

PASSCODE

2 Use the CURSOR or button to highlight the “7/

PASSCODE” line. Press ENTER to display the “PASSCODE” menu. You can also select the “PASSCODE” menu directly by pressing the INPUT “7” button.

3 Use the CURSOR or button to select “ENTRY”. Press

ENTER to display the “NEW PASSCODE?” menu. You can also select the “NEW PASSCODE?” menu directly by pressing the INPUT “1” button.

4 Enter a four digit passcode using the “1” through “0” buttons.

1) Each time you press the INPUT button, an asterisk will

appear under the “NEW PASSCODE?” message.

NOTE: ”0000" and “9999” cannot be used as a passcode.

2) Once you have finished entering your four digit passcode,

press ENTER to store the code.

– ADJUST – 1 / SIGNAL ENTRY 2 / FOCUS 3 / ALIGNMENT 4 / CONVERGENCE 5 / KELVIN 6 / R,G,B GAIN

7 / PASSCODE

8 / OPTION 9 / REF.ADJUST

– PASSCODE –

1 / ENTRY

2 / DISABLE

NEW PASSCODE?

––––

3) If the passcode has been entered correctly, the “CONFIRM

NEW PASSCODE?” menu will be displayed.

NOTE: If the passcode is not entered correctly, the “WARNING PASSCODE!!” message will be displayed. You will be required to enter the passcode correctly.

PASSCODE

5 Enter the new passcode again.

1) Each time you press the INPUT button, an asterisk will

appear under the “CONFIRM NEW PASSCODE?” message.

2) Once you have finished entering the new four digit passcode,

press ENTER.

3) If the entered passcode is correct, the “CHANGE

PASSCODE COMPLETE!!” message will be displayed.

NOTE: If the passcode is not correct, the “WARNING DIFFERENT PASSCODE!!” message will be displayed. You are required to enter the new passcode correctly.

6 To complete, press the END button.

• When the END button is pressed once, the “RETURN USER MODE?” menu will be displayed. Use the CURSOR or button to select either “YES” or “NO” and then press ENTER. This will exit the ADJUST mode.

CONFIRM NEW PASSCODE?

––––

RETURN USER MODE?

YES NO

Items to select

• YES ......... When you try to enter the ADJUST mode again,

you will need to re-enter your passcode.

• NO ........... When you try to enter the ADJUST mode again,

you will not need to re-enter your passcode.

Changing Your Passcode

To change your passcode, proceed as follows:

1 Press the ADJUST button.

• The “PASSCODE?” screen will be displayed.

2 Enter the four digit current passcode using the “1” through “0”

buttons. Press ENTER.

• The “ADJUST” menu will be displayed.

PASSCODE

3 Use the CURSOR or button to highlight the “7/

PASSCODE” line. Press ENTER to display the “PASSCODE” menu. You can also select the “PASSCODE” menu directly by pressing the INPUT “7” button.

4 Use the CURSOR or button to select “1/ENTRY”. Press

ENTER to display the “CURRENT PASSCODE?” menu. You can also select the “CURRENT PASSCODE?” menu directly by pressing the INPUT “1” button.

5 Enter the four digit passcode (the current passcode) using the “1”

through “0” buttons.

1) Each time you press the INPUT button, an asterisk will

appear under the “CURRENT PASSCODE?” message.

2) Once you have finished entering the four digit passcode, press

ENTER.

– ADJUST – 1 / SIGNAL ENTRY 2 / FOCUS 3 / ALIGNMENT 4 / CONVERGENCE 5 / KELVIN 6 / R,G,B GAIN

7 / PASSCODE

8 / OPTION 9 / REF.ADJUST

– PASSCODE –

1 / ENTRY

2 / DISABLE

CURRENT PASSCODE?

∗∗∗∗

3) If the entered passcode is correct, the “NEW PASSCODE?”

screen will be displayed.

NOTE: If the passcode is not correct, the “WARNING DIFFERENT PASSCODE!!” message is displayed. You will be required to enter the correct current passcode.

PASSCODE

6 Enter a new passcode using the “1” through “0” buttons.

1) Each time you press the INPUT button, an asterisk will

appear under the “NEW PASSCODE?” message.

2) Once you have finished entering the four digit new passcode,

press ENTER.

3) If the passcode has been entered correctly, the “CONFIRM

NEW PASSCODE?” menu will be displayed.

NOTE: If the passcode is not entered correctly, the “WARNING PASSCODE!!” message will be displayed. You are required to enter the new passcode correctly.

7 Enter the new passcode again using the “1” through “0” buttons.

1) Each time you press the INPUT button, an asterisk will

appear under the “CONFIRM NEW PASSCODE?” message.

2) Once you have finished entering the four digit new passcode,

press ENTER.

NEW PASSCODE?

––––

CONFIRM NEW PASSCODE?

––––

3) If the entered passcode is correct, the “CHANGE

PASSCODE COMPLETE!!” message is displayed.

NOTE: If the passcode is not entered correctly, the “WARNING DIFFERENT PASSCODE!!” message is displayed. You will be required to enter the new passcode correctly.

8 To complete, press the END button.

• Whenever the END button is pressed, the “RETURN USER MODE?” menu will be displayed. Use the CURSOR or button to select either “YES” or “NO” and press ENTER. This will exit the ADJUST mode.

Items to select

• YES ......... When you try to enter the ADJUST mode again,

you will need to re-enter your passcode.

• NO ........... When you try to enter the ADJUST mode again,

you will not need to re-enter your passcode.

RETURN USER MODE?

YES NO

Canceling Your Passcode

To cancel the passcode, proceed as follows: 1 Press the ADJUST button and then enter your passcode.

• The “PASSCODE?” screen will be displayed.

PASSCODE

2 Enter the four digit current passcode using the “1” through “0”

buttons and then press ENTER.

• The “ADJUST” menu will be displayed.

3 Use the CURSOR or button to highlight “7/PASSCODE”.

Press the ENTER button to display the “PASSCODE” menu. You can also select the “PASSCODE” menu directly by pressing the INPUT “7” button.

4 Use the CURSOR or button to select “2/DISABLE”. Press

ENTER to display the “CURRENT PASSCODE?” menu. You can also select the “CURRENT PASSCODE?” menu directly by pressing the INPUT “2” button.

5 Enter the four digit passcode (the current passcode) using the “1”

through “0” buttons.

1) Each time you press the INPUT button, an asterisk will appear under the “CURRENT PASSCODE?” message.

2) Once you have finished entering the four digit passcode, press ENTER.

– ADJUST – 1 / SIGNAL ENTRY 2 / FOCUS 3 / ALIGNMENT 4 / CONVERGENCE 5 / KELVIN 6 / R,G,B GAIN

7 / PASSCODE

8 / OPTION 9 / REF.ADJUST

– PASSCODE – 1 / ENTRY

2 / DISABLE

CURRENT PASSCODE?

∗∗∗∗

3) If the entered passcode is correct, the “PASSCODE DISABLE?” menu will be displayed.

NOTE: If the passcode is not correct, the “WARNING DIFFERENT PASSCODE!!” message will be displayed. You will be required to enter your correct passcode.

6 Use the CURSOR or button to select either “YES” or “NO”

and then press ENTER.

Items to select

• YES ......... When selecting “YES”, the current passcode will

be canceled. You will not be required to re-enter your passcode when you press the ADJUST button to re-enter the ADJUST mode.

• NO ........... When selecting “NO”, the current passcode will

remain in effect.

PASSCODE DISABLE?

YES NO

12345

SETTING.

Displaying the Various Setting Features

You can view some of the setting features and check to make sure that the settings are appropriate.

To display setting features on the screen, hold down CTL and press INFO. To eliminate the display, press END.

The parameters cannot be changed on the SETTING VIEW screen shown on the right. For changing parameters of the setting features, refer to the following pages.

NOTE: The INPUT TERMINAL item on the “SETTING MODE” menu cannot be changed.

P01/P03 PJ ORIENTATION

CONNECT CONDITION DEFAULT INPUT SELECT FOCUS EDGE MODE ALL S-VIDEO MODE SELECT S2

VIDEO MODE SELECT

P02/P03 AUTO POWER ON MODE

WARM-UP MODE AUTOMATIC DATA STORE PHOSPHOR SAVER OFF SIGNAL SWITCHING SOUND

P03/P03 DIRECT ENTRY ACCESS

B-FOCUS TRACKING OPTION TERM BAUD RATE RGB/COMPONENT SEARCH

OPTION – SETTING MODE –



CEILING FRONT

STANDALONE LAST

AUTO

OPTION – SETTING MODE –



INACTIVE INACTIVE DISABLE

MUTE ON PICTURE MUTE ON

OPTION – SETTING MODE –



DISABLE OFF 9600 BPS

MANUAL



Projection Type Selection

This feature allows you to set the installation type according to the projection configuration.

NOTE:

• You do not need to change the setting for XG-852C and XG-1352C. These models are pre-adjusted at the factory for "FLOOR/FRONT".

1 Press the ADJUST button to display the “ADJUST” menu.

• The projector may ask you to enter your passcode. See page 68 for the explanation of the PASSCODE.

2 Use the CURSOR or button to highlight the “8/OPTION”

line. Press ENTER to display the “OPTION” menu. You can also select the “OPTION” menu directly by pressing the INPUT “8” button.

SETTING

– ADJUST – 1 / SIGNAL ENTRY 2 / FOCUS 3 / ALIGNMENT 4 / CONVERGENCE 5 / KELVIN 6 / R,G,B GAIN 7 / PASSCODE

8 / OPTION

9 / REF.ADJUST

3 Use the CURSOR or button to highlight the “1/SETTING

MODE” line. Press ENTER to display the “SETTING MODE” menu. You can also select the “SETTING MODE” menu directly by pressing the INPUT “1” button.

4 Use the CURSOR or button to select the “PJ ORIENTA-

TION” item, then press ENTER to display the “PJ ORIENTATION” menu.

NOTE: The SETTING MODE has three menus. The “PJ ORIENTATION” item is on the first menu (P01). To access P02 or P03 from P01, press and hold down the CTL button then press the button; to return to P01 from P02 or P03, press and hold down the CTL button then press the button.

– OPTION –

1 / SETTING MODE

2 / MENU MODE 3 / SEQUENCER 4 / PJ ADDRESS 5 / VERSION 6 / HOUR METER 7 / DEFAULT DATA

P01/P03

PJ ORIENTATION

CONNECT CONDITION DEFAULT INPUT SELECT FOCUS EDGE MODE ALL S-VIDEO MODE SELECT S2

VIDEO MODE SELECT

OPTION – SETTING MODE –



CEILING FRONT

STANDALONE LAST

AUTO

SETTING

5 Use the CURSOR or button to select one of the four

projector installation types and press ENTER.

Items to select

• CEILING/REAR .... Ceiling mounting type and rear projection

• FLOOR/REAR....... Desk top type and rear projection

• CEILING/FRONT .. Ceiling mounting type and front projection

• FLOOR/FRONT..... Desk top type and front projection

6 To complete, press the END button.

• Whenever the END button is pressed, the menus will sequence in this order: “OPTION” menu → “ADJUST” menu → Source screen

• If the “RETURN USER MODE?” menu appears, use the CURSOR or button to select either “YES” or “NO” and press ENTER. This will exit the ADJUST mode.

Items to select

• YES ......... When you try to enter the ADJUST mode the next

time, you will need to re-enter your passcode.

• NO ........... When you try to enter the ADJUST mode the next

time, you will not need to re-enter your passcode.

PJ ORIENTATION

CEILING/REAR FLOOR/REAR

CEILING/FRONT

FLOOR/FRONT

RETURN USER MODE?

YES NO

Connecting to the Switcher

This setting explains how the projector is used with the ISS-6020/ ISS-6020G Switcher.

1 Press the ADJUST button to display the “ADJUST” menu.

• The projector may ask you to enter your passcode. See page 68 for the explanation of the PASSCODE.

SETTING

2 Use the CURSOR or button to highlight the “8/OPTION”

line. Press ENTER to display the “OPTION” menu. You can also select the “OPTION” menu directly by pressing the INPUT “8” button.

3 Use the CURSOR or button to highlight the “1/SETTING

MODE” line. Press ENTER to display the “SETTING MODE” menu. You can also select the “SETTING MODE” menu directly by pressing the INPUT “1” button.

4 Use the CURSOR or button to select the “CONNECT

CONDITION” item, then press ENTER to display the “CONNECT CONDITION” menu.

NOTE: The SETTING MODE has three menus. The “CONNECT CONDITION” item is on the first menu (P01). To access P02 or P03 from P01, press and hold down the CTL button then press the button; to return to P01 from P02 or P03, press and hold down the CTL button then press the button.

– ADJUST – 1 / SIGNAL ENTRY 2 / FOCUS 3 / ALIGNMENT 4 / CONVERGENCE 5 / KELVIN 6 / R,G,B GAIN 7 / PASSCODE

8 / OPTION

9 / REF.ADJUST

– OPTION –

1 / SETTING MODE

2 / MENU MODE 3 / SEQUENCER 4 / PJ ADDRESS 5 / VERSION 6 / HOUR METER 7 / DEFAULT DATA

P01/P03 PJ ORIENTATION

CONNECT CONDITION

DEFAULT INPUT SELECT FOCUS EDGE MODE ALL S-VIDEO MODE SELECT S2

VIDEO MODE SELECT AUTO

OPTION – SETTING MODE –



CEILING FRONT

STANDALONE LAST

5 Use the CURSOR or button to select your desired connec-

tion condition of Switcher and press ENTER.

• The “RE-START ?” prompt is displayed after setting of the connection condition is modified from the current status to your desired condition.

Items to select

• STAND ALONE ....The projector used in stand alone operation.

• SW 1 LEVEL ........ The projector used with one Switcher.

• SW 2 LEVEL ........ The projector used with two or more

Switchers.

CONNECT CONDITION

STANDALONE

SW1 LEVEL

SW2 LEVEL

SETTING

6 Use the CURSOR or button to select either “YES” or “NO”

and press ENTER.

Items to select

• YES ......... Restart the projector.

• NO ........... Does not restart the projector.

NOTE: The selected connection condition becomes effective only after the projector is restarted.

7 To exit, press the END button.

• Whenever the END button is pressed, the menus will sequence in this order: “OPTION” menu → “Adjust” menu → Source screen

• If the “RETURN USER MODE?” menu appears, use the CURSOR or button to select “YES” or “NO” and then press ENTER.

Items to select

• YES ......... When you try to enter the ADJUST mode the next

time, you will need to re-enter your passcode.

• NO ........... When you try to enter the ADJUST mode the next

time, you will not need to re-enter your passcode.

RE-START?

YES NO

RETURN USER MODE?

YES NO

Default Input Selection

You can set the projector to default to any one of its inputs each time the projector is turned on. Proceed as follows:

1 Press the ADJUST button to display the “ADJUST” menu.

• The projector may ask you to enter your passcode. See page 68 for the explanation of the PASSCODE.

SETTING

2 Use the CURSOR or button to highlight the “8/OPTION”

line. Press ENTER to display the “OPTION” menu. You can also select the “OPTION” menu directly by pressing the INPUT “8” button.

3 Use the CURSOR or button to highlight the “1/SETTING

MODE” line. Press ENTER to display the “SETTING MODE” menu. You can also select the “SETTING MODE” menu directly by pressing the INPUT “1” button.

4 Use the CURSOR or button to select the “DEFAULT

INPUT SELECT” item, then press ENTER to display the “DEFAULT INPUT SELECT” menu.

NOTE: The SETTING MODE has three menus. The “DEFAULT INPUT SELECT” item is on the first menu (P01). To access P02 or P03 from P01, press and hold down the CTL button then press the button; to return to P01 from P02 or P03, press and hold down the CTL button then press the button.

– ADJUST – 1 / SIGNAL ENTRY 2 / FOCUS 3 / ALIGNMENT 4 / CONVERGENCE 5 / KELVIN 6 / R,G,B GAIN 7 / PASSCODE

8 / OPTION

9 / REF.ADJUST

– OPTION –

1 / SETTING MODE

2 / MENU MODE 3 / SEQUENCER 4 / PJ ADDRESS 5 / VERSION 6 / HOUR METER 7 / DEFAULT DATA

P01/P03 PJ ORIENTATION

CONNECT CONDITION

DEFAULT INPUT SELECT

FOCUS EDGE MODE ALL S-VIDEO MODE SELECT S2

VIDEO MODE SELECT AUTO

OPTION – SETTING MODE –



CEILING FRONT

STANDALONE LAST

SETTING

5 Use the CURSOR or button to select either “LAST” or

“DEFAULT” and press ENTER.

• Selecting “LAST” completes setting. Go on to step 7.

• Selecting “DEFAULT” displays the “Default input” screen. Go

on to step 6.

Items to select

• LAST ....... Sets the projector to default to the previous last

active input each time the projector is turned on. Note: An input must be active for a minimum of 10 minutes before it is recognized as the last active signal.

• DEFAULT . Displays the same source input every time the

projector is started up.

6 Use the CURSOR or button to select an input and then press

the ENTER button.

When used in stand alone operation:

The default input screen will be displayed. Use the CURSOR or button to select an input and press ENTER.

DEFAULT INPUT SELECT

LAST

DEFAULT



INPUT SELECT 

INPUT A RGB

INPUT A VIDEO INPUT A S-VIDEO INPUT A COMPONENT INPUT B RGB INPUT B VIDEO INPUT B S-VIDEO INPUT B COMPONENT INPUT C RGB INPUT C VIDEO INPUT C S-VIDEO INPUT C COMPONENT

When used with a single Switcher:

The “MASTER” slot menu will be displayed. Use the CURSOR or button to select the desired slot number “1” through “10(0)” and then press ENTER.

When used with two or more Switchers:

The “MASTER” and “SLAVE” slot number menu will be displayed. Use the CURSOR or button to select the master slot number first and then select the slave slot number “1” through “10(0)”. Press ENTER.

MASTER

SLOT–01

SLOT–02 SLOT–03 SLOT–04 SLOT–05 SLOT–06 SLOT–07 SLOT–08 SLOT–09 SLOT–10

MASTER

SLOT–01

SLOT–02 SLOT–03 SLOT–04 SLOT–05 SLOT–06 SLOT–07 SLOT–08 SLOT–09 SLOT–10

SLAVE

SLOT–01

SLOT–02 SLOT–03 SLOT–04 SLOT–05 SLOT–06 SLOT–07 SLOT–08 SLOT–09 SLOT–10

7 To complete, press the END button.

• Whenever the END button is pressed, the menus will sequence in this order: “OPTION” menu → “ADJUST” menu → Source screen

• If the “RETURN USER MODE?” menu appears, use the CURSOR or button to select either “YES” or “NO” and press ENTER. This will exit the ADJUST mode.

Items to select

• YES ......... When you try to enter the ADJUST mode the next

time, you will need to re-enter your passcode.

• NO ........... When you try to enter the ADJUST mode the next

time, you will not need to re-enter your passcode.

SETTING

RETURN USER MODE?

YES NO

SETTING

Focus Edge Mode

This function allows you to set either of two electrical edge focus modes; one affects all the RGB patterns at the same time and the other each CRT separately. To set this, proceed as follows:

1 Press the ADJUST button to display the “ADJUST” menu.

• The projector may ask you to enter your passcode. See page 68 for the explanation of the PASSCODE.

2 Use the CURSOR or button to highlight the “8/OPTION”

line. Press ENTER to display the “OPTION” menu. You can also select the “OPTION” menu directly by pressing the INPUT “8” button.

3 Use the CURSOR or button to highlight the “1/SETTING

MODE” line. Press ENTER to display the “SETTING MODE” menu. You can also select the “SETTING MODE” menu directly by pressing the INPUT “1” button.

– ADJUST – 1 / SIGNAL ENTRY 2 / FOCUS 3 / ALIGNMENT 4 / CONVERGENCE 5 / KELVIN 6 / R,G,B GAIN 7 / PASSCODE

8 / OPTION

9 / REF.ADJUST

– OPTION –

1 / SETTING MODE

2 / MENU MODE 3 / SEQUENCER 4 / PJ ADDRESS 5 / VERSION 6 / HOUR METER 7 / DEFAULT DATA

4 Use the CURSOR or button to select the “FOCUS EDGE

MODE” item on Page 1, then press ENTER to display the “FOCUS EDGE MODE” menu.

NOTE: The SETTING MODE has three menus. The “FOCUS EDGE MODE” item is on the first menu (P01). To access P02 or P03 from P01, press and hold down the CTL button then press the button; to return to P01 from PO2 or P03, press and hold down the CTL button then press the button.

P01/P03 PJ ORIENTATION

CONNECT CONDITION DEFAULT INPUT SELECT

FOCUS EDGE MODE ALL

S-VIDEO MODE SELECT S2

VIDEO MODE SELECT AUTO

OPTION – SETTING MODE –



CEILING FRONT

STANDALONE LAST

5 Use the CURSOR or button to select either “ALL” or

“SEPARATE” and press ENTER.

Items to select

• ALL...................... Affects all of the CRTs at the same time

• SEPARATE........... Affects each CRT separately

6 To complete, press the END button.

• Whenever the END button is pressed, the menus will sequence in this order: “OPTION” menu → “ADJUST” menu → Source screen

• If the “RETURN USER MODE?” menu appears, use the CURSOR or button to select either “YES” or “NO” and press ENTER. This will exit the ADJUST mode.

Items to select

• YES ......... When you try to enter the ADJUST mode the next

time, you will need to re-enter your passcode.

• NO ........... When you try to enter the ADJUST mode the next

time, you will not need to re-enter your passcode.

SETTING

FOCUS EDGE MODE

ALL

SEPARATE

RETURN USER MODE?

YES NO

SETTING

S-Video Mode Selection

This function is used to select the S-video signal detection mode. This allows identifying of the S-video signals with different aspect ratio: squeeze or full mode(16 : 9) and letter box (4 : 3) signals.

NOTE: An identifying result will be displayed in the SOURCE INFORMATION screen.

To set, proceed as follows:

1 Press the ADJUST button to display the “ADJUST” menu.

• The projector may ask you to enter your passcode. See page 68 for the explanation of the PASSCODE.

2 Use the CURSOR or button to highlight the “8/OPTION”

line. Press ENTER to display the “OPTION” menu. You can also select the “OPTION” menu directly by pressing the INPUT “8” button.

– ADJUST – 1 / SIGNAL ENTRY 2 / FOCUS 3 / ALIGNMENT 4 / CONVERGENCE 5 / KELVIN 6 / R,G,B GAIN 7 / PASSCODE

8 / OPTION

9 / REF.ADJUST

3 Use the CURSOR or button to highlight the “1/SETTING

MODE” line. Press ENTER to display the “SETTING MODE” menu. You can also select the “SETTING MODE” menu directly by pressing the INPUT “1” button.

4 Use the CURSOR or button to select the “S-VIDEO MODE

SELECT” item, then press ENTER to display the “S-VIDEO MODE SELECT” menu.

NOTE: The SETTING MODE has three menus. The “S-VIDEO MODE SELECT” menu is on the first menu (P01). To access P02 or P03 from P01, press and hold down the CTL button then press the button; to return to P01 from P02 or P03, press and hold down the CTL button then press the button.

– OPTION –

1 / SETTING MODE

2 / MENU MODE 3 / SEQUENCER 4 / PJ ADDRESS 5 / VERSION 6 / HOUR METER 7 / DEFAULT DATA

P01/P03

PJ ORIENTATION

CONNECT CONDITION DEFAULT INPUT SELECT FOCUS EDGE MODE ALL

S-VIDEO MODE SELECT S2

VIDEO MODE SELECT AUTO

OPTION – SETTING MODE –



CEILING FRONT

STANDALONE LAST

5 Use the CURSOR or button to select one of the three items:

S2, S1, and OFF, and then press ENTER.

Items to select

S2.............. Identifies squeeze and letter box signals.

S1.............. Identifies a squeeze signal only.

OFF ............ Does not identify any S-video signal.

6 To end, press the END button.

• Whenever the END button is pressed, the menus will sequence in this order: “OPTION” menu → “ADJUST” menu → Source screen

• If the “RETURN USER MODE?” menu appears, use the CURSOR or button to select either “YES” or “NO” and press ENTER. This will exit the ADJUST mode.

Items to select

• YES ......... When you try to enter the ADJUST mode the next

time, you will need to re-enter your passcode.

• NO ........... When you try to enter the ADJUST mode the next

time, you will not need to re-enter your passcode.

SETTING

S-VIDEO MODE SELECT

S2

S1 OFF

RETURN USER MODE?

YES NO

NOTE :

• The input signal must be compatible with the S2/S1 MODE

standard. Refer to the user manual included with the connected equipment for more information.

• The identification function may not work correctly with a non-

compatible signal. If this happens, select “OFF” from the “SVIDEO MODE SELECT” menu.

SETTING

Video Mode Selection

This function is used to select the NTSC 3.58, NTSC 4.43, PAL or SECAM video standard. To select any one of the video standards, proceed as follows:

1 Press the ADJUST button to display the “ADJUST” menu.

• The projector may ask you to enter your passcode. See page 68 for the explanation of the PASSCODE.

2 Use the CURSOR or button to highlight the “8/OPTION”

line. Press ENTER to display the “OPTION” menu. You can also select the “OPTION” menu directly by pressing the INPUT “8” button.

3 Use the CURSOR or button to highlight the “1/SETTING

MODE” line. Press ENTER to display the “SETTING MODE” menu. You can also select the “SETTING MODE” menu directly by pressing the INPUT “1” button.

4 Use the CURSOR or button to select the “VIDEO MODE

SELECT” item, then press ENTER to display the “VIDEO MODE SELECT” menu.

NOTE: The SETTING MODE has three menus. The “VIDEO MODE SELECT” menu is on the first menu (P01). To access P02 or P03 from P01, press and hold down the CTL button then press the button; to return to P01 from P02 or P03, press and hold down the CTL button then press the button.

– ADJUST – 1 / SIGNAL ENTRY 2 / FOCUS 3 / ALIGNMENT 4 / CONVERGENCE 5 / KELVIN 6 / R,G,B GAIN 7 / PASSCODE

8 / OPTION

9 / REF.ADJUST

– OPTION –

1 / SETTING MODE

2 / MENU MODE 3 / SEQUENCER 4 / PJ ADDRESS 5 / VERSION 6 / HOUR METER 7 / DEFAULT DATA

P01/P03 PJ ORIENTATION

CONNECT CONDITION DEFAULT INPUT SELECT FOCUS EDGE MODE ALL S-VIDEO MODE SELECT S2

VIDEO MODE SELECT

OPTION – SETTING MODE –



CEILING FRONT

STANDALONE LAST

AUTO

5 Use the CURSOR or button to select either “AUTO” or

“MANUAL” and then press ENTER.

SETTING

When selecting “AUTO”

One of the video standards is selected automatically and is displayed in the SOURCE INFORMATION screen.

Video Modes

• NTSC3.58 ............Indicates the NTSC3.58 video standard

• NTSC4.43 ............Indicates the NTSC4.43 video standard

• PAL .....................Indicates the PAL video standard

• SECAM ................Indicates the SECAM video standard

• RGB.....................Indicates the RGB mode

• Select “AUTO” in normal operation.

When selecting “MANUAL”

The “VIDEO MODE SELECT” menu will be displayed. Use the CURSOR or button to select the preferred video mode and then press ENTER.

Items to select

• NTSC3.58 Switches to the NTSC3.58 mode

• NTSC4.43 Switches to the NTSC4.43 mode

• PAL ......... Switches to the PAL mode

• SECAM .... Switches to the SECAM mode

VIDEO MODE SELECT

AUTO

MANUAL

VIDEO MODE SELECT

NTSC 3.58

NTSC 4.43 PAL SECAM

• Select “MANUAL” when connecting to poor quality signal or non-standard signals such as video games.

NOTE: The projector may not function correctly with a monochrome signals in the AUTO mode.

6 To complete, press the END button.

• Whenever the END button is pressed, the menus will sequence in this order: “OPTION” menu → “ADJUST” menu → Source screen

• When your passcode is in effect, the “RETURN USER MODE?” menu is displayed. If this happens, use the CURSOR or button to select either “YES” or “NO” and press ENTER.

Items to select

• YES ......... When you try to enter the ADJUST mode the next

time, you will need to re-enter your passcode.

• NO ........... When you try to enter the ADJUST mode the next

time, you will not need to re-enter your passcode.

RETURN USER MODE?

YES NO

SETTING

Auto Power ON Mode Setting

The AUTO POWER ON MODE is a convenient way to start up the projector without pressing the POWER button. You can turn the projector on and off by supplying AC power to the projector. To do this, proceed as follows:

1 Press the ADJUST button to display the “ADJUST” menu.

• The projector may ask you to enter your passcode. See page 68 for the explanation of the PASSCODE.

2 Use the CURSOR or button to highlight the “8/OPTION”

line. Press ENTER to display the “OPTION” menu. You can also select the “OPTION” menu directly by pressing the INPUT “8” button.

3 Use the CURSOR or button to highlight the “1/SETTING

MODE” line. Press ENTER to display the “SETTING MODE” menu. You can also select the “SETTING MODE” menu directly by pressing the INPUT “1” button.

4 Use the CURSOR or button to select the “AUTO POWER

ON MODE” item on Page 2, then press ENTER to display the “AUTO POWER ON MODE” menu.

NOTE: The SETTING MODE has three menus. The “AUTO POWER ON MODE” item is on the second menu (P02). To access P02 from P01, press and hold down the CTL button then press the button; to return to P01 from P02, press and hold down the CTL button then press the button.

– ADJUST – 1 / SIGNAL ENTRY 2 / FOCUS 3 / ALIGNMENT 4 / CONVERGENCE 5 / KELVIN 6 / R,G,B GAIN 7 / PASSCODE

8 / OPTION

9 / REF.ADJUST

– OPTION –

1 / SETTING MODE

2 / MENU MODE 3 / SEQUENCER 4 / PJ ADDRESS 5 / VERSION 6 / HOUR METER 7 / DEFAULT DATA

P02/P03

AUTO POWER ON MODE

WARM-UP MODE AUTOMATIC DATA STORE PHOSPHOR SAVER OFF SIGNAL SWITCHING SOUND

OPTION – SETTING MODE –



INACTIVE INACTIVE DISABLE

MUTE ON PICTURE MUTE ON

5 Use the CURSOR or button to select either “ACTIVE” or

“INACTIVE” and press the ENTER button.

SETTING

Items to select

• INACTIVE. Normal operation setting. Power ON is accom-

plished through the rear panel or the POWER button on the remote control.

• ACTIVE .... Bypasses rear panel power button (or the POWER

button on the remote control) to allow power ON to be controlled by an AC switched outlet.

6 To complete, press the END button.

• Whenever the END button is pressed, the menus will sequence in this order: “OPTION” menu → “ADJUST” menu → Source screen

• If the “RETURN USER MODE?” menu appears, use the CURSOR or button to select either “YES” or “NO” and then press ENTER.

Items to select

• YES ......... When you try to enter the ADJUST mode the next

time, you will need to re-enter your passcode.

• NO ........... When you try to enter the ADJUST mode the next

time, you will not need to re-enter your passcode.

AUTO POWER ON MODE

INACTIVE

ACTIVE

RETURN USER MODE?

YES NO

SETTING

Warm-up Mode Setting

This function allows you to automatically warm up the projector from 5 to 15 minutes when the projector is turned on. To set the Warm-up mode, proceed as follows:

1 Press the ADJUST button to display the “ADJUST” menu.

• The projector may ask you to enter your passcode. See page 68 for the explanation of the PASSCODE.

2 Use the CURSOR or button to highlight the “8/OPTION”

line. Press ENTER to display the “OPTION” menu. You can also select the “OPTION” menu directly by pressing the INPUT “8” button.

3 Use the CURSOR or button to highlight the “1/SETTING

MODE” line. Press ENTER to display the “SETTING MODE” menu. You can also select the “SETTING MODE” menu directly by pressing the INPUT “1” button.

– ADJUST – 1 / SIGNAL ENTRY 2 / FOCUS 3 / ALIGNMENT 4 / CONVERGENCE 5 / KELVIN 6 / R,G,B GAIN 7 / PASSCODE

8 / OPTION

9 / REF.ADJUST

– OPTION –

1 / SETTING MODE

2 / MENU MODE 3 / SEQUENCER 4 / PJ ADDRESS 5 / VERSION 6 / HOUR METER 7 / DEFAULT DATA

4 Use the CURSOR or button to select the “WARM-UP

MODE” item on Page 2, then press ENTER to display the “WARM-UP MODE” menu.

NOTE: The SETTING MODE has three menus. The “WARM-UP MODE” item is on the second menu (P02). To access P02 from P01, press and hold down the CTL button then press the button; to return to P01 from P02, press and hold down the CTL button then press the button.

P02/P03 AUTO POWER ON MODE

WARM-UP MODE

AUTOMATIC DATA STORE PHOSPHOR SAVER OFF SIGNAL SWITCHING SOUND

OPTION – SETTING MODE –



INACTIVE INACTIVE DISABLE

MUTE ON PICTURE MUTE ON

5 Use the CURSOR or button to select either “ACTIVE” or

“INACTIVE” and press ENTER.

SETTING

Items to select

• INACTIVE. Displays the input source after the projector is

turned on.

• ACTIVE .... Activates the warm-up program after the projector

is turned on. The ALL WHITE test pattern will be displayed. You can select a warm-up time from the WARM-UP TIME menu.

NOTE: To interrupt and cancel the warm-up cycle, press the END button.

6 To complete, press the END button.

• Whenever the END button is pressed, the menus will sequence in this order: “OPTION” menu → “ADJUST” menu → Source screen

• If the “RETURN USER MODE?” menu appears, use the CURSOR or button to select either “YES” or “NO” and then press ENTER.

Items to select

• YES ......... When you try to enter the ADJUST mode the next

time, you will need to re-enter your passcode.

• NO ........... When you try to enter the ADJUST mode the next

time, you will not need to re-enter your passcode.

WARM-UP MODE

INACTIVE

ACTIVE

WARM-UP TIME

5 MIN

10 MIN 15 MIN

RETURN USER MODE?

YES NO

SETTING

Automatic Save Feature

This feature allows you to select two ways to store settings; automatically and manually. After “ENABLE” is selected in the AUTOMATIC DATA STORE menu, all projector settings are stored in the projector's memory automatically. To set the AUTOMATIC DATA STORE, proceed as follows:

1 Press the ADJUST button to display the “ADJUST” menu.

• The projector may ask you to enter your passcode. See page 68 for the explanation of the PASSCODE section.

2 Use the CURSOR or button to highlight the “8/OPTION”

line and then press ENTER to display the “OPTION” menu. You can also select the “OPTION” menu directly by pressing the INPUT “8” button.

3 Use the CURSOR or button to highlight the “1/SETTING

MODE” line. Press ENTER to display the “SETTING MODE” menu. You can also select the “SETTING MODE” menu directly by pressing the INPUT “1” button.

– ADJUST – 1 / SIGNAL ENTRY 2 / FOCUS 3 / ALIGNMENT 4 / CONVERGENCE 5 / KELVIN 6 / R,G,B GAIN 7 / PASSCODE

8 / OPTION

9 / REF.ADJUST

– OPTION –

1 / SETTING MODE

2 / MENU MODE 3 / SEQUENCER 4 / PJ ADDRESS 5 / VERSION 6 / HOUR METER 7 / DEFAULT DATA

4 Use the CURSOR or button to select the “AUTOMATIC

DATA STORE” item on Page 2, then press ENTER to display the “AUTOMATIC DATA STORE” menu.

NOTE: The SETTING MODE has three menus. The “AUTOMATIC DATA STORE” item is on the second menu (P02). To access P02 from P01, press and hold down the CTL button then press the button ; to return to P01 from P02, press and hold down the CTL button then press the button.

P02/P03 AUTO POWER ON MODE

WARM-UP MODE

AUTOMATIC DATA STORE

PHOSPHOR SAVER SIGNAL SWITCHING SOUND

OPTION – SETTING MODE –



INACTIVE INACTIVE DISABLE

OFF

MUTE ON PICTURE MUTE ON

5 Use the CURSOR or button to select either “DISABLE” or

“ENABLE” and then press ENTER.

Items to select

• DISABLE.. Projector does not store the settings automatically.

• ENABLE ... Projector stores the settings automatically.

Automatic storing data is done when any one of the following procedures is performed:

• Pressing the END button several times returns the adjustment screen to the source screen.

• One input is switched to another.

• The projector is turned off.

• Every 10 minutes.

NOTE: After “DISABLE” is selected in the AUTOMATIC DATA STORE menu, the settings will not be stored in the memory unless you select “YES” in the “STORE ?” menu.

SETTING

AUTOMATIC DATA STORE

DISABLE

ENABLE

6 If the “RETURN USER MODE?” menu appears, use the

CURSOR or button to select either “YES” or “NO” and press ENTER. This will exit the ADJUST mode.

Items to select

• YES ......... When you try to enter the ADJUST mode the next

time, you will need to re-enter your passcode.

• NO ........... When you try to enter the ADJUST mode the next

time, you will not need to re-enter your passcode.

RETURN USER MODE?

YES NO

SETTING

Phosphor Saver Setting

This function allows you to safeguard the CRTs against burns by shifting the image vertically and horizontally on the screen in the regular intervals. This can prolong the life of CRT of the projector. To set the Phosphor saver, proceed as follows:

1 Press the ADJUST button to display the “ADJUST” menu.

• The projector may ask you to enter your passcode. See page 68 for the explanation of the PASSCODE.

2 Use the CURSOR or button to highlight the “8/OPTION”

line. Press ENTER to display the “OPTION” menu. You can also select the “OPTION” menu directly by pressing the INPUT “8” button.

3 Use the CURSOR or button to highlight the “1/SETTING

MODE” line. Press ENTER to display the “SETTING MODE” menu. You can also select the “SETTING MODE” menu directly by pressing the INPUT “1” button.

– ADJUST – 1 / SIGNAL ENTRY 2 / FOCUS 3 / ALIGNMENT 4 / CONVERGENCE 5 / KELVIN 6 / R,G,B GAIN 7 / PASSCODE

8 / OPTION

9 / REF.ADJUST

– OPTION –

1 / SETTING MODE

2 / MENU MODE 3 / SEQUENCER 4 / PJ ADDRESS 5 / VERSION 6 / HOUR METER 7 / DEFAULT DATA

4 Use the CURSOR or button to select the “PHOSPHOR

SAVER” item on Page 2, then press ENTER to display the “PHOSPHOR SAVER” menu.

NOTE: The SETTING MODE has three menus. The “PHOSPHOR SAVER” item is on the second menu (P02). To access P02 from P01, press and hold down the CTL button then press the button; to return to P01 from P02, press and hold down the CTL button then press the button.

P02/P03 AUTO POWER ON MODE

WARM-UP MODE AUTOMATIC DATA STORE

PHOSPHOR SAVER

SIGNAL SWITCHING SOUND

OPTION – SETTING MODE –



INACTIVE INACTIVE DISABLE

OFF

MUTE ON PICTURE MUTE ON

5 Use the CURSOR or button to select either “OFF” or “ON”

and press ENTER.

SETTING

Items to select

• OFF.......... Deactivates the PHOSPHOR SAVER function.

• ON ........... Activates the PHOSPHOR SAVER function. Interval

and number of steps can be set.

NOTE: When the on-screen display appears or you are in the adjustment mode, this function is cancelled. This can cause the source screen to be shifted.

6 Use the CURSOR or button to select your desired interval

time from the “INTERVAL” menu and press ENTER.

• The “STEP” menu is displayed on the screen.

Items to select

• DEMO (1 SEC)........... Works every one second

• 5 MINUTES ............... Works every 5 minutes.

• 20 MINUTES ............. Works every 20 minutes

• 1 HOUR ..................... Works every 1 hour

PHOSPHOR SAVER

OFF

INTERVAL DEMO(1SEC) 5 MINUTES

20 MINUTES

1 HOUR

STEP 4 STEP 6 STEP

8 STEP

7 Use the CURSOR or button to select the number of steps

you wish.

Items to select

• 4 STEP ....... Moves 4 steps of POSTIION adjustment value

• 6 STEP ....... Moves 6 steps of POSITION adjustment value

• 8 STEP ....... Moves 8 steps of POSITION adjustment value

8 To complete, press the END button.

• Whenever the END button is pressed, the menus will sequence in this order: “OPTION” menu → “ADJUST” menu → Source screen

• If the “RETURN USER MODE?” menu appears, use the CURSOR or button to select either “YES” or “NO” and then press ENTER.

Items to select

• YES ......... When you try to enter the ADJUST mode the next

time, you will need to re-enter your passcode.

• NO ........... When you try to enter the ADJUST mode the next

time, you will not need to re-enter your passcode.

RETURN USER MODE?

YES NO

SETTING

Signal Switching Mute Mode Setting

This function allows you to mute the picture and/or sound during signal switching. To set the Signal Switching Mute mode, proceed as follows:

1 Press the ADJUST button to display the “ADJUST” menu.

• The projector may ask you to enter your passcode. See page 68 for the explanation of the PASSCODE.

2 Use the CURSOR or button to highlight the “8/OPTION”

line. Press ENTER to display the “OPTION” menu. You can also select the “OPTION” menu directly by pressing the INPUT “8” button.

3 Use the CURSOR or button to highlight the “1/SETTING

MODE” line. Press ENTER to display the “SETTING MODE” menu. You can also select the “SETTING MODE” menu directly by pressing the INPUT “1” button.

– ADJUST – 1 / SIGNAL ENTRY 2 / FOCUS 3 / ALIGNMENT 4 / CONVERGENCE 5 / KELVIN 6 / R,G,B GAIN 7 / PASSCODE

8 / OPTION

9 / REF.ADJUST

– OPTION –

1 / SETTING MODE

2 / MENU MODE 3 / SEQUENCER 4 / PJ ADDRESS 5 / VERSION 6 / HOUR METER 7 / DEFAULT DATA

4 Use the CURSOR or button to select the “SIGNAL

SWITCHING” item on Page 2, then press ENTER to display the “SIGNAL SWITCHING” menu.

NOTE: The SETTING MODE has three menus. The “SIGNAL SWITCHING” menu is on the second menu (P02). To access P02 from P01, press and hold down the CTL button then press the button; to return to P01 from P02, press and hold down the CTL button then press the button.

P02/P03 AUTO POWER ON MODE

WARM-UP MODE AUTOMATIC DATA STORE PHOSPHOR SAVER

SIGNAL SWITCHING SOUND

OPTION – SETTING MODE –



INACTIVE INACTIVE DISABLE

OFF

MUTE ON PICTURE MUTE ON

5 Use the CURSOR or button to select either “SOUND” or

“PICTURE”, and press the ENTER button.

• The “SOUND MUTE” or “PICTURE MUTE” menu will be displayed.

6 Use the CURSOR or button to select either “ON” or “OFF”

and then press ENTER.

Items to select

MUTE ON... Mutes a picture and/or sound during switching

signals.

MUTE OFF.. Outputs a picture and/or sound during switching

signals.

SIGNAL SWITCHING MUTE

SOUND

PICTURE

SOUND MUTE

ON

OFF

ON OFF

SETTING

7 To complete this, press END.

• Whenever the END button is pressed, the menus will sequence in this order: “OPTION” menu → “ADJUST” menu → Source screen

• If the “RETURN USER MODE?” menu appears, use the CURSOR or button to select either “YES” or “NO” and then press ENTER.

Items to select

• YES ......... When you try to enter the ADJUST mode the next

time, you will need to re-enter your passcode.

• NO ........... When you try to enter the ADJUST mode the next

time, you will not need to re-enter your passcode.

RETURN USER MODE?

YES NO

SETTING

Direct Entry Access Setting

This feature allows you to switch the current input directly to one of the registered inputs from NO1 to NO10 in the INPUT LIST.

NOTE: To use this feature, hold down the CTL button and press one of the INPUT buttons corresponding to the input number.

To set this feature, proceed as follows:

1 Press the ADJUST button to display the “ADJUST” menu.

• The projector may ask you to enter your passcode. See page 68 for the explanation of the PASSCODE.

2 Use the CURSOR or button to highlight the “8/OPTION”

line. Press ENTER to display the “OPTION” menu. You can also select the “OPTION” menu directly by pressing the INPUT “8” button.

3 Use the CURSOR or button to highlight the “1/SETTING

MODE” line. Press ENTER to display the “SETTING MODE” menu. You can also select the “SETTING MODE” menu directly by pressing the INPUT “1” button.

– ADJUST – 1 / SIGNAL ENTRY 2 / FOCUS 3 / ALIGNMENT 4 / CONVERGENCE 5 / KELVIN 6 / R,G,B GAIN 7 / PASSCODE

8 / OPTION

9 / REF.ADJUST

– OPTION –

1 / SETTING MODE

2 / MENU MODE 3 / SEQUENCER 4 / PJ ADDRESS 5 / VERSION 6 / HOUR METER 7 / DEFAULT DATA

4 Use the CURSOR or button to select the “DIRECT ENTRY

ACCESS” item on Page 3, then press ENTER to display the “DIRECT ENTRY ACCESS” menu.

NOTE: The SETTING MODE has three menus. The “DIRECT ENTRY ACCESS” item is on the third menu (P03). To access P03 from P01, press and hold down the CTL button then press the button twice; to return to P01 from P03, press and hold down the CTL button then press the button twice.

P03/P03

DIRECT ENTRY ACCESS

B-FOCUS TRACKING OPTION TERM BAUD RATE RGB/COMPONENT SEARCH

OPTION – SETTING MODE –



DISABLE

OFF 9600 BPS

MANUAL

5 Use the CURSOR or button to select either “DISABLE” or

“ENABLE” and press ENTER.

Items to select

• DISABLE.. An error message will appear at the bottom of the

screen and the signal is not switched when one of the INPUT buttons is pressed with CTL.

• ENABLE ... The signal is switched to the corresponding signal

when one of the INPUT button is pressed with CTL.

6 To complete this, press END.

• Whenever the END button is pressed, the menus will sequence in this order. “OPTION” menu → “ADJUST” menu → Source screen

• If the RETURN USER MODE ? menu appears, use the CURSOR or button to select either “YES” or “NO” and press ENTER. This will exit the ADJUST mode.

Items to select

• YES ......... When you try to enter the ADJUST mode the next

time, you will need to re-enter your passcode.

• NO ........... When you try to enter the ADJUST mode the next,

you will not need to re-enter your passcode.

SETTING

DIRECT ENTRY ACCESS

DISABLE

ENABLE

RETURN USER MODE?

YES NO

SETTING

Blue Focus Tracking Setting

This feature allows you to obtain the better white uniformity by defocusing the blue CRT.

NOTE:

• The defocus values will vary with changes in the horizontal frequency.

• Select the “ALL WHITE” pattern using the TEST button on the full function remote control.

1 Press the ADJUST button to display the “ADJUST” menu.

• The projector may ask you to enter your passcode. See page 68 for the explanation of PASSCODE.

2 Use the CURSOR or button to highlight the “8/OPTION”

line. Press ENTER to display the “OPTION” menu. You can also select the “OPTION” menu directly by pressing the INPUT “8” button.

3 Use the CURSOR or button to highlight the “1/SETTING

MODE” line. Press ENTER to display the “SETTING MODE” menu. You can also select the “SETTING MODE” menu directly by pressing the INPUT “1” button.

4 Use the CURSOR or button to select the “B-FOCUS

TRACKING” item on Page 3, then press ENTER to display the “B-FOCUS TRACKING” menu.

NOTE: The SETTING MODE has three menus. The “B-FOCUS TRACKING” item is on the third menu (P03). To access P03 from P01, press and hold down the CTL button then press the

button twice; to return to P01 from P03, press and hold

down the CTL button then press the button twice.

5 Use the CURSOR or button to select either “OFF” or

“ON” and press ENTER.

Items to select

•OFF ...... Defocuses the blue CRT

•ON ....... Does not defocus the blue CRT

– ADJUST – 1 / SIGNAL ENTRY 2 / FOCUS 3 / ALIGNMENT 4 / CONVERGENCE 5 / KELVIN 6 / R,G,B GAIN 7 / PASSCODE

8 / OPTION

9 / REF.ADJUST

– OPTION –

1 / SETTING MODE

2 / MENU MODE 3 / SEQUENCER 4 / PJ ADDRESS 5 / VERSION 6 / HOUR METER 7 / DEFAULT DATA

P03/P03 DIRECT ENTRY ACCESS

B-FOCUS TRACKING

OPTION TERM BAUD RATE



RGB/COMPONENT SEARCH

OPTION – SETTING MODE –



DISABLE OFF 9600 BPS MANUAL

6 To end this mode, press the END button.

• Whenever the END button is pressed, the menu will sequence in this order. “OPTION” menu→”ADJUST” menu→Source screen.

• If the “RETURN USER MODE?” menu appears, use the CURSOR or button to select either “YES” or “NO” and then press ENTER. This will exit the ADJUST mode.

Items to select

•YES...... When you try to enter the ADJUST mode the next time,

you will need to re-enter your passcode.

•NO ....... When you try to enter the ADJUST mode the next time,

you will not need to re-enter your passcode.

B-FOCUS TRACKING

OFF

RETURN USER MODE?

YES NO

100

NEC MultiSync XG-852C, MultiSync XG-1352C Setup Manual

Specifications and Main Features

Frequently Asked Questions

User Manual