NEC MultiSync LCD2000, MultiSync 2000SE, MultiSync LCD400, LCD4002000, LA-1421JMW User Manual

MultiSync

®

LCD400

™

LCD2000

™

User’s Manual

Contents 1
Quick Start 2-3
Controls 4-5
Recommended Use 6-7
Specifications 8-9
Features 10
Troubleshooting 11
References 12
Limited Warranty 13

MultiSync

®

LCD400

™

LCD2000

™

User’s Manual

78132391 5/5/98, 8:33 AM1

TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT USE
THIS UNIT'S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE PRONGS
CAN BE FULLY INSERTED.
REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE. REFER SERVICING
TO QUALIFIED SERVICE PERSONNEL.

WARNING

CAUTION

RISK OF ELECTRIC SHOCK • DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER
SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This

symbol warns user that uninsulated voltage within the unit may have sufficient magnitude to cause

electric shock. Therefore, it is dangerous to make any kind of contact with any part inside this unit.
This symbol alerts the user that important literature concerning the operation and maintenance of this

unit has been included. Therefore, it should be read carefully in order to avoid any problems.

Canadian Department of Communications Compliance Statement

DOC: This Class B digital apparatus meets all requirements of the Canadian

Interference-Causing Equipment Regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du

Règlement sur le matériel brouiller du Canada.

C-UL: Bears the C-UL Mark and is in compliance with Canadian Safety Regulations

according to C.S.A. C22.2 No. 950.
Ce produit porte la marque ‘C-UL’ et se conforme aux règlements de sûrele

Canadiens selon CAN/CSA C22.2 No. 950.

FCC Information

1.

Use the attached specified cables with the LA-1421JMW and LA-2031JMW

color monitors
so as not to interfere with radio and television reception.
(1)

Please use the supplied shielded power cable or equivalent to ensure FCC compliance.
(2) MultiSync® LCD400™ monitor: Shielded video signal cable.
(3) MultiSync

®

LCD2000™ monitor: Shielded 15-pin VGA to BNC cable.
Use of other cables and adapters may cause interference with radio and television
reception.

2.

This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment gener­ates, uses, and can radiate radio frequency energy, and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.

• Consult your dealer or an experienced radio/TV technician for help.

If necessary, the user should contact the dealer or an experienced radio/television technician
for additional suggestions. The user may find the following booklet, prepared by the Federal
Communications Commission, helpful: ”How to Identify and Resolve Radio-TV Interference
Problems.“ This booklet is available from the U.S. Government Printing Office, Washington,
D.C., 20402, Stock No. 004-000-00345-4.

78132391 5/5/98, 8:33 AM2

MultiSync LCD

2000

M

ultiSync LCD

400

Contents

1

Your new NEC Technologies MultiSync® LCD monitor box* should
contain the following:

• MultiSync LCD Monitor with tilt/swivel base
MultiSync LCD400™ monitor, LA-1421JMW or
MultiSync LCD2000™ monitor, LA-2031JMW

• Power Cord

• Video Signal Cable (LCD400)

• 15-pin VGA to BNC Cable (LCD2000)

• User’s Manual

• Registration Card

* Remember to save your original box

and packing material to transport
or ship the monitor.

MultiSync LCD2000 monitor
with 15-pin VGA to BNC Cable

Power Cord

That’s right. Sim

ply com

plete and return this

regisitration, and we’ll send the purchasing party

a check for $25.00 And we’ll also enter you in

our “100,000 G

ive Away II” for a chance to win

$5,000, $25,00 or $50,000! Thank Uou for your

tim

e, and thanks for

choosing NEC.

Receive a $25

Purchaser Rebate

to thank you for

choosing an

N

EC M

ultiSync

®

LCD M

onitor

PRODUCT REGISTRATION

SEE, HEAR AND FEEL THE DIFFERENCE.

™

N

E

C

M

u

l

t

i

S

y

n

c

M

o

n

i

t

o

r

s

Give Away II

MultiSync

®

LCD

400

LCD

2000

User’s Manual

Contents 1

Quick Start 2-3

Controls 4-5

Recommended Use 6-7

Specifications 8-9

Features 10

Troubleshooting 11

Reference 12

Limited Warranty 13

XtraView

MultiSync LCD400
monitor with Video Signal Cable

User’s Manual Registration Card

78132391 5/5/98, 8:34 AM3

Quick Start

To attach the MultiSync® LCD monitor to your system, follow these
instructions:

1. Turn off the power to your computer.

2. For the PC: Connect the 15-pin mini D-SUB of the appropriate signal cable

to the connector of the display card in your system (Figure A.1). Tighten all screws.
For the Mac: Connect the MultiSync LCD

400

™

or MultiSync LCD

2000

™

Macintosh

cable
adapter to the computer (Figure B.1). Attach the 15-pin mini D-SUB end of the
appropriate signal cable to the MultiSync LCD

400 or MultiSync LCD2000 Macintosh

cable adapter (Figure B.1). Tighten all screws.

NOTE: To obtain the MultiSync LCD

400 or MultiSync LCD2000 Macintosh cable

adapter, call NEC Technologies at [phone].

3. For the MultiSync LCD

400

: Connect the 15-pin mini D-SUB of the video signal cable to the
appropriate connector on the back of the monitor (Figure C1). For the MultiSync
LCD

2000

: Connect the BNC cables to the appropriate connectors on the back of the
monitor. Connect the red BNC cable to the BNC connector on the monitor labeled R, the
green BNC cable to the BNC connector labeled G/Sync, the blue BNC cable to the BNC
connector labeled B. If you have a fourth BNC connector (Composite Sync), connect it to
the BNC connector on the monitor labeled H/CS. If you have a fifth BNC connector
(Vertical Sync), connect it to the BNC connector on the monitor labeled VS (Figure D.1).

NOTE: Incorrect cable connections may result in irregular operation, damage

display quality/components of LCD module and/or shorten the module’s life.

4. Connect one end of the power cord to the MultiSync LCD Series monitor and the other
end to the power outlet (Figure E.1).

5. Turn on the monitor (Figure F.1) and the computer.

6.

To complete the setup of your MultiSync LCD monitor, use the following OSM™ controls:

• Auto Adjust Contrast

• Auto Adjust

• Image Adjust – Fine (MultiSync LCD

2000 monitor only)

Refer to the Controls section of this User’s Manual for a full description of these OSM controls.
NOTE: If you have any problems, please refer to the Troubleshooting section of

this User’s Manual.

2

Figure A.1 Figure B.1

15-pin
mini D-SUB

Mac Adapter
(not included)

15-pin

mini

D-SUB

78132391 5/5/98, 8:34 AM4

H/CS VS R G/Sync B

Quick Start

3

Figure F.1

Figure D.1

Figure C.1

Figure E.1

MultiSync LCD400

monitor

MultiSync LCD2000
monitor

MultiSync LCD400

monitor

MultiSync LCD2000
monitor

Power Switch

Power Switch

5-pin

78132391 5/5/98, 8:34 AM5

4

OSM™ (On-Screen-Manager) Controls

The OSM controls on the front of the monitor function as follows:

Control Main Menu Sub-Menu

EXIT Exits the OSM controls. Exits to the OSM controls

main menu.

CONTROL / Moves the highlighted Moves the highlighted area

area up/down to select up/down to select one of the
one of the controls. controls.

CONTROL –/+ Has no function. Moves the bar in the + or –

direction to increase or
decrease the adjustment.

PROCEED Proceeds to the selected Activates Auto Adjust feature.

menu choice (indicated In Display Mode, opens
by the highlighted area). additional window.

RESET: The currently Resets all the controls within Resets the highlighted control.
highlighted control to the highlighted menu.
the factory setting.

NOTE: When RESET is pressed, a warning window will appear

allowing you to cancel the reset function.

Brightness and Contrast

Brightness: Adjusts the overall image and background screen brightness.
Contrast: Adjusts the image brightness in relation to the background.
Auto Adjust Contrast: Corrects the image displayed for non-standard video inputs.

Auto Adjust

MultiSync® LCD400™ monitor: Allows automatic adjustment of the Position

and Image Adjust controls.

MultiSync® LCD2000™ monitor: Allows automatic adjustment of the Position

and Image Adjust Coarse control.

Position

Controls horizontal and vertical image position within the display
area of the LCD.
Auto Adjust Position: Automatically sets the horizontal and vertical image

position within the display area of the LCD.

Image Adjust

Coarse: Adjusts the horizontal size by increasing or decreasing the Coarse setting.
Fine: Improves focus, clarity and image stability by increasing or

decreasing the Fine setting.

NOTE: The Image Adjust Fine control must be used to complete the setup of

your MultiSync LCD

2000

monitor.

Auto Adjust Coarse/Fine: (MultiSync LCD

400

monitor only) Automatically

adjusts the Coarse or Fine settings.

Auto Adjust Coarse: (MultiSync LCD

2000

monitor only) Automatically

adjusts the Coarse setting.

Controls

78132391 5/5/98, 8:34 AM6

5

Controls

AccuColor™ Control System

Color presets select the desired color setting. If a setting is adjusted, the name of
the setting will change to Custom

.
Color Gain (Red, Green, Blue): Increases or decreases Red, Green or Blue
color depending upon which is selected. The change in color will appear on
screen and the direction (increase or decrease) will be shown by the color
bars.

OSM™ Location

You can choose where you would like the OSM control image to appear on
your screen. Selecting OSM Location allows you to manually adjust the
position of the OSM control menu left, right, up or down.

OSM Turn Off Time

The OSM control menu will stay on as long as it is in use. In the OSM Turn
Off Time submenu, you can select how long the monitor waits after the last
touch of a button to shut off the OSM control menu. The preset choices are
10, 20, 30, 60 and 120 seconds.

OSM Lock Out

This control completely locks out access to all OSM control functions. When
attempting to activate OSM controls while in the Lock Out mode, a screen
will appear indicating the OSM controls are locked out. To activate the
OSM Lock Out function, press PROCEED, then and hold down simulta­neously. To de-activate the OSM Lock Out, press PROCEED, then

and hold

down simultaneously.

Display Mode

Display Mode provides information about the current resolution display and
technical data including the preset timing being used and the horizontal and
vertical frequencies.
NOTE: Mode Change should only be used if a resolution is not recognized

by the monitor. The user can change to the appropriate resolution
by entering the Display Mode sub-menu and selecting the
corresponding option.

Language Select

OSM control menus are available in six languages.

Factory Preset

Selecting Factory Preset allows you to reset all OSM control settings back to
the factory settings. The RESET button will need to be held down for several
seconds to take effect. Individual settings can be reset by highlighting the
control to be reset and pressing the RESET button.

78132391 5/5/98, 8:34 AM7

Safety Precautions and Maintenance

FOR OPTIMUM PERFORMANCE, PLEASE NOTE THE

FOLLOWING WHEN SETTING UP AND USING

THE MULTISYNC® LCD COLOR MONITOR:

• DO NOT OPEN THE MONITOR. There are no user serviceable parts inside
and opening or removing covers may expose you to dangerous shock hazards
or other risks. Refer all servicing to qualified service personnel.

• Allow adequate ventilation around the monitor so that heat can properly
dissipate. Do not block ventilated openings or place the monitor near a
radiator or other heat sources. Do not put anything on top of monitor.

• Do not spill any liquids into the cabinet or use your monitor near water.

• Do not insert objects of any kind into the cabinet slots, as they may touch

dangerous voltage points, which can be harmful or fatal or may cause electric
shock, fire or equipment failure.

• Do not place any heavy objects on the power cord. Damage to the cord may
cause shock or fire.

• Do not place this product on a sloping or unstable cart, stand or table, as the
monitor may fall, causing serious damage to the monitor.

• The power cable connector is the primary means of detaching the system from
the power supply. The monitor should be installed close to a power outlet that
is easily accessible.

• When operating the MultiSync LCD monitor with its AC220-240V worldwide
power supply, use a power supply cord that matches the power supply voltage of
the AC power outlet being used. The power supply cord you use must have been
approved by and comply with the safety standards of your country.

• Handle with care when transporting. Save packaging for transporting.

Immediately unplug your monitor from the wall outlet and refer servicing to
qualified service personnel under the following conditions:

• When the power supply cord or plug is damaged.

• If liquid has been spilled, or objects have fallen into the monitor.

• If the monitor has been exposed to rain or water.

• If the monitor has been dropped or the cabinet damaged.

• If the monitor does not operate normally by following operating instructions.

Recommended Use

6

78132391 5/5/98, 8:34 AM8

CORRECT PLACEMENT AND ADJUSTMENT OF THE MONITOR

CAN REDUCE EYE, SHOULDER AND NECK FATIGUE. CHECK THE

FOLLOWING WHEN YOU POSITION THE MONITOR:

Recommended Use

• For optimum performance, allow 20 minutes for warm-up.

• Adjust the monitor height so that the top of the screen is at or slightly below

eye level. Your eyes should look slightly downward when viewing the middle
of the screen.

•

Position your monitor no closer than 16 inches and no further away than
28 inches from your eyes. The optimal distance is 21 inches for the
MultiSync® LCD 400™ and 24 inches for the MultiSync® LCD 2000™ monitor.

• Rest your eyes periodically by focusing on an object at least 20 feet away.
Blink often.

• Position the monitor at a 90° angle to windows and other light sources to
minimize glare and reflections. Adjust the monitor tilt so that ceiling lights do
not reflect on your screen.

• If reflected light makes it hard for you to see your screen, use an anti-glare filter.

• Clean the LCD monitor surface with a lint-free, non-abrasive cloth. Avoid using

any cleaning solution or glass cleaner!

• Adjust the monitor’s brightness and contrast controls to enhance readability.

• Use a document holder placed close to the screen.

• Position whatever you are looking at most of the time (the screen or

reference material) directly in front of you to minimize turning your head
while you are typing.

• Avoid displaying fixed patterns on the monitor for long periods of time to avoid
image persistence (after-image effects).

• Get regular eye checkups.

For more detailed information on setting up a healthy work environment, call NEC
at [phone], NEC FastFacts

™

information at [phone] and request
document #900108 or write the American National Standard for Human Factors
Engineering of Visual Display Terminal Workstations – ANSI-HFS Standard
No. 100-1988 – The Human Factors Society, Inc. P.O. Box 1369, Santa Monica,
California 90406.

7

78132391 5/5/98, 8:34 AM9

Specifications

8

Monitor MultiSync® LCD400

™

Notes

Specifications Monitor

LCD Module Diagonal: 14.1 inch Active matrix; thin film transistor (TFT)

Viewable Image Size: 14.1 inch liquid crystal display (LCD); 0.28 mm dot

Native Resolution (Pixel Count): 1024 x 768 pitch, XtraView™ technology; 180cd/m

2

white luminence; 100:1 contrast ratio, typical

Input Signal Video: ANALOG 0.7 Vp-p/75 Ohms

Sync: Separate sync. TTL Level

Horizontal sync. Positive/Negative
Vertical sync. Positive/Negative
Composite sync. (Positive/Negative) (TTL Level)
Sync on Green video (Positve) 0.7 Vp-p and sync.
Negative 0.3 Vp-p

Display Colors Analog input: Unlimited number of colors Depends on display card used.
Synchronization Horizontal: 24.8 kHz to 60 kHz Automatically

Range Vertical: 56.2 Hz to 85.1 Hz Automatically
Resolutions Supported 720 x 400: VGA text

Some systems may not support

Resolution based on

horizontal and

640 x 480* at 60Hz to 85Hz

all modes listed.

vertical frequencies only

800 x 600* at 56Hz to 85Hz
832 x 624* at 75Hz

1024 x 768 at 60Hz to 75Hz ....................

NEC cites recommended resolution at
60 Hz for optimal display performance.

Active Display Area Horizontal:

286 mm/11.3 inches Dependent upon signal timing used,

Vertical:

214 mm/8.4 inches and does not include border area.

Power Supply

AC 100 – 120 V/220 – 240 V @ 50/60 Hz

Current Rating 0.9A @ 100

–

120 V/0.5 A @ 220 – 240 V

Dimensions

357 mm (W) x 362 mm (H) x 168 mm (D)

14.1 inches (W) x 14.3 inches (H) x 6.7 inches (D)

Weight 5.2 kg

11.5 lbs

Environmental Considerations

Operating Temperature: 5°C to +35°C/41°F to 95°F

Humidity: 30% to 80%

Feet: 0 to 10,000 Feet

Storage Temperature: -10°C to +60°C/14°F to 140°F

Humidity: 10% to 85%

Feet: 0 to 45,000 Feet

* Interpolated Resolutions: When resolutions are shown that are lower than the pixel count of the LCD module, text may

appear choppy or lines may appear to be bold. This is normal and necessary for all current flat panel technologies when
displaying non-native resolutions full screen. In flat panel technologies, each dot on the screen is actually one pixel, so to
expand resolutions to full screen, an interpolation of the resolution must be done. When the interpolated resolution is not
an exact multiple of the native resolution, the mathematical interpolation necessary may cause some lines to appear thicker
than others.

NOTE: Technical specifications are subject to change without notice.

78132391 5/5/98, 8:34 AM10

9

Monitor MultiSync® LCD2000

™

Notes

Specifications Monitor

LCD Module Diagonal: 20.1 inch Active matrix; thin film transistor (TFT)

Viewable Image Size: 20.1 inch liquid crystal display (LCD); 0.31 mm dot

Native Resolution (Pixel Count): 1280 x 1024 pitch, XtraView™ technology; 150cd/m

2

white

luminence; 100:1 contrast ratio, typical

Input Signal Video: ANALOG 0.7 Vp-p/75 Ohms

Sync: Separate sync. TTL Level

Horizontal sync. Positive/Negative
Vertical sync. Positive/Negative
Composite sync. (Positive/Negative) (TTL Level)
Sync on Green video (Positve) 0.7 Vp-p and sync.
Negative 0.3 Vp-p

Display Colors Analog input: Unlimited number of Colors Depends on display card used.
Synchronization Horizontal: 24.0 kHz to 80 kHz Automatically

Range Vertical: 56.0 Hz to 76 Hz Automatically
Resolutions Supported 720 x 400*: VGA text

Some systems may not support

Resolution based on

horizontal and

640 x 480 at 60Hz to 76Hz

all modes listed.

vertical frequencies only

800 x 600* at 56Hz to 76Hz
832 x 624* at 75Hz
1024 x 768* at 60Hz to 76Hz
1280 x 960 at 60Hz to 76Hz

1280 x 1024 at 60Hz to 76Hz ..................

NEC cites recommended resolution at
60 Hz for optimal display performance.

Active Display Area Horizontal:

399 mm/15.7 inches Dependent upon signal timing used,

Vertical:

319 mm/12.6 inches and does not include border area.

Power Supply

AC 100 – 120 V/ 220 – 240 V @ 50/60 Hz

Current Rating 1.0A @ 100

–

120 V/0.5A @ 220 – 240 V

Dimensions

500 mm (W) x 483 mm (H) x 220 mm (D)

19.7 inches (W) x 19.0 inches (H) x 8.7 inches (D)

Weight 10.0 kg

22.0 lbs

Environmental Considerations

Operating Temperature: 5°C to +30°C/41°F to 86°F

Humidity: 30% to 80%

Feet: 0 to 10,000 Feet

Storage Temperature: -10°C to +60°C/14°F to 140°F

Humidity: 10% to 85%

Feet: 0 to 45,000 Feet

* Interpolated Resolutions: When resolutions are shown that are lower than the pixel count of the LCD module, text may

appear choppy or lines may appear to be bold. This is normal and necessary for all current flat panel technologies when
displaying non-native resolutions full screen. In flat panel technologies, each dot on the screen is actually one pixel, so to
expand resolutions to full screen, an interpolation of the resolution must be done. When the interpolated resolution is not
an exact multiple of the native resolution, the mathematical interpolation necessary may cause some lines to appear thicker
than others.

NOTE: Technical specifications are subject to change without notice.

78132391 5/5/98, 8:34 AM11

10

Features

Analog Advantage: Capable of displaying unlimited colors in a continuous
spectrum, providing a truer representation of color. The monitor’s high contrast
LCD enhances color vibrancy and improves focus with no geometric distortion.

Wider Compatibility: Because the MultiSync LCD monitor is analog through and
through, it does not require special analog to digital display or interface cards
but can accept RGB input directly.

Reduced Footprint: Provides the ideal solution for environments requiring
superior image quality but with size and weight limitations. The monitor’s small
footprint and low weight allow it to be moved or transported easily from one
location to another.

AccuColor® Control System: Allows you to adjust the colors on your screen and
customize the color accuracy of your monitor to a variety of standards.

OSM™ (On-Screen Manager) Controls: Allow you to quickly and easily adjust all
elements of your screen image via simple to use on-screen menus.

ErgoDesign® Features: Enhance human ergonomics to improve the working
environment, protect the health of the user and save money. Examples include
OSM controls for quick and easy image adjustments, tilt/swivel base for pre­ferred angle of vision, small footprint and compliance with MPRII guidelines for
lower emissions.

Plug and Play (MultiSync® LCD400™ monitor only): The Microsoft® solution with
the Windows®95 operating system facilitates setup and installation by allowing
the monitor to send its capabilities (such as screen size and resolutions supported)
directly to your computer, automatically optimizing display performance.

IPM™ (Intelligent Power Manager) System: Provides innovative power-saving
methods that allow the monitor to shift to a lower power consumption level when
on but not in use, saving two-thirds of your monitor energy costs, reducing
emissions and lowering the air conditioning costs of the workplace.

Multiple Frequency Technology: Automatically adjusts monitor to the display
card’s scanning frequency, thus displaying the resolution required.

FullScan™ Capability: Allows you to use the entire screen area in most resolu­tions, significantly expanding image size.

OSM Display Screen Copyright 1997 by NEC Technologies, Inc.

78132391 5/5/98, 8:34 AM12

11

T roubleshooting

No picture

•

The signal cable should be completely connected to the display card/computer.

• The display card should be completely seated in its slot.

• Power Switch and computer power switch should be in the ON position.

• Check to make sure that a supported mode has been selected on the display
card or system being used. (Please consult display card or system manual to
change graphics mode.)

• Check the monitor and your display card with respect to compatibility and
recommended settings.

• Check the signal cable connector for bent or pushed-in pins.

Image persistence

• Image persistence is when a “ghost” of an image remains on the screen even
after the monitor has been turned off. Unlike CRT monitors, LCD monitors’
image persistence is not permanent. To alleviate image persistence, turn the
monitor off for as long as an image was displayed. If an image was on the
monitor for one hour and a ”ghost” of that image remains, the monitor
should be turned off for one hour to erase the image.

NOTE: As with all personal display devices, NEC Technologies recommends
using a screen saver at regular intervals whenever the screen is idle.

Image is unstable, unfocused or swimming is apparent

• Signal cable should be completely attached to the computer.

• Use the OSM Image Adjust controls to focus and adjust display by
increasing or decreasing the fine total. When the display mode is changed,
the OSM Image Adjust settings may need to be re-adjusted.

• Check the monitor and your display card with respect to compatibility
and recommended signal timings.

LED on monitor is not lit

(no green or amber color can be seen)

• Power Switch should be in the ON position and power cord should
be connected.

• Make certain the computer is not in a power-saving mode (touch the
keyboard or mouse).

Display image has a green cast to it

• Open OSM Display Mode and press the “+” Control button.

Display image is not sized properly

• Use the OSM Image Adjust controls to increase or decrease the Coarse total.

• Check to make sure that a supported mode has been selected on the display
card or system being used. (Please consult display card or system manual to
change graphics mode.)

Selected resolution is not displayed properly

• Use OSM Display Mode to enter Mode Change sub-menu and confirm that
the appropriate resolution has been selected. If not, select corresponding
option.

78132391 5/5/98, 8:34 AM13

12

References

• BBS [phone]

NEC Technologies’ Remote Bulletin Board System is an electronic service
accessible with your system and a modem. Communication parameters
are: 300/1200/2400/9600/14.4k/28.8k/33.3k bps, no parity, 8-data bits,
1 stop bit

• Customer Service/
Technical Support [phone]

Fax [phone]

• Electronic Channels:

Internet e-mail: [e-mail]
Internet ftp site: ftp.nectech.com
CompuServe: go NECTECH
America Online: keyword NECTECH
World Wide Web: http://www.nec.com

• FastFacts™ Information [phone]

INFORMATION DESCRIPTION DOCUMENT #

MultiSync® LCD400™ monitor Detailed monitor information 142102
MultiSync® LCD2000™ monitor Detailed monitor information 203101
Glossary Definition of terms related 900203

to functions, features and
installation of the
MultiSync monitor

More Information Names and addresses of 900204

other groups involved in
standards and features of
the MultiSync monitor

Macintosh Connection Detailed information on 153006

connecting the MultiSync
monitor to a Macintosh

Healthy Work Environment Detailed information on 900108

setting up a healthy work
environment

• Literature & Sales Info (800) NEC-INFO [[phone]]

• MultiSync Fulfillment [phone]

[For software & accessories]

• TeleSales [phone]

78132391 5/5/98, 8:34 AM14

NEC Technologies, Inc. (hereinafter “NECTECH”), warrants this Product to be free from defects
in material and workmanship and, subject to the conditions set forth below, agrees to repair or
replace any part of the enclosed unit,

other than the LCD backlight,

which proves defective for
a period of three (3) years from the date of first consumer purchase. The LCD backlight is
warranted for a period of one (1) year. Spare parts are warranted for ninety (90) days.

This warranty gives you specific legal rights and you may also have other rights which vary
from state to state. This warranty is limited to the original purchaser of the Product and is not
transferable. This warranty covers only NECTECH-supplied components. Service required as
a result of third party components is not covered under this warranty.

Proof of Purchase will be required by NECTECH to substantiate date of purchase. Such proof
of purchase must be an original bill of sale or receipt containing name and address of seller,
purchaser, and the serial number of the product.

It shall be your obligation and expense to have the Product shipped, freight prepaid, or
delivered to the authorized reseller from whom it was purchased or other facility authorized
by NECTECH to render the services provided hereunder in either the original package or a
similar package affording an equal degree of protection. All Products returned to NECTECH
for service MUST have prior approval, which may be obtained by calling [phone].

The Product shall not have been previously altered, repaired, or serviced by anyone other
than a service facility authorized by NECTECH to render such service, the serial number
of the product shall not have been altered or removed. The Product shall not have been
subjected to accident, misuse, or abuse or operated contrary to the instructions contained
in the User’s Manual.

NECTECH SHALL NOT BE LIABLE FOR DIRECT, INDIRECT, INCIDENTAL, CONSEQUENTIAL,
OR OTHER TYPES OF DAMAGES RESULTING FROM THE USE OF ANY NECTECH
PRODUCT OTHER THAN THE LIABILITY STATED ABOVE. THESE WARRANTIES ARE IN LIEU OF
ALL OTHER WARRANTIES EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE
IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
SOME STATES DO NOT ALLOW THE EXCLUSION OF IMPLIED WARRANTIES OR THE
LIMITATION OR EXCLUSION OF LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL
DAMAGES SO THE ABOVE EXCLUSIONS OR LIMITATIONS MAY NOT APPLY TO YOU.

This Product is warranted in accordance with the terms of this limited warranty. Consumers
are cautioned that Product performance is affected by system configuration, software, the
application, customer data, and operator control of the system, among other factors. While
NECTECH Products are considered to be compatible with many systems, specific functional
implementation by the customers of the Product may vary. Therefore, suitability of a Product
for a specific purpose or application must be determined by consumer and is not warranted
by NECTECH.

For the name of your nearest authorized NECTECH service facility, contact NECTECH
at [phone].

Limited Warranty

13

78132391 5/5/98, 8:34 AM15

NEC LCD Series

Part No. 78132391

Printed in Japan

PROPRIETARY NOTICE AND LIABILITY DISCLAIMER

The information disclosed in this document, including all designs and related materials, is the valuable property of NEC
Technologies and/or its licensors, as appropriate, reserve all patent, copyright and other proprietary rights to this
document, including all design, manufacturing, reproduction, use and sales rights thereto, except to the extent said rights
are expressly granted to others.

The NEC Technologies product(s) discussed in this document are warranted in accordance with the terms of the Limited
Warranty Statement accompanying each product. However, actual performance of each such product is dependent upon
factors such as system configuration, customer data and operator control. Since implementation by customers of each
product may vary, the suitability of specific product configurations and applications must be determined by the customer
and is not warranted by NEC Technologies.

To allow for design and specification improvements, the information in this document is subject to change at any time
without notice. Reproduction of this document or portions thereof without prior approval of NEC Technologies is
prohibited.

DECLARATION OF CONFORMITY

This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions. (1) This device may
not cause harmful interference, and (2) this device must accept any interference received, including interference that may
cause undesired operation.

U.S. Responsible Party: NEC Technologies, Inc.
Address: 1250 North Arlington Heights Road

Itasca, Illinois 60143-1298

Tel. No.: [phone]

Type of Product: Computer Monitor
Equipment Classification: Class B Peripheral
Model: LA-1421JMW

We hereby declare that the equipment specified above

conforms to the technical standards as specified in the FCC Rules.

MultiSync is a registered trademark of NEC Technologies, Inc. in the U.S. and of NEC Home Electronics, Ltd. in Canada, UK, Germany, France,
Spain, Italy, Austria, Benelux, Switzerland, Denmark, Finland, Norway and Saudi Arabia. AccuColor and ErgoDesign are registered
trademarks of NEC Technologies, Inc. in the U.S. and Canada. LCD400, LCD2000, XtraView, IPM, FastFacts, FullScan and OSM are trademarks
of NEC Technologies, Inc. in the U.S. NEC is a registered trademark of NEC Corporation Copyright 1997 by NEC Technologies, Inc. OSM
Display Screens Copyright 1997 by NEC Technologies, Inc. Windows is a registered trademark of Microsoft Corporation. All other brands
and product names are trademarks or registered trademarks of their respective owners.

As a Energy Star Partner, NEC Technologies has determined that this product meets the Energy Star guidelenes for energy efficiency.
The Energy Star emblem does not represent EPA endorsement of any product or service.

NEC Technologies, Inc.
1250 North Arlington Heights Road
Itasca, Illinois 60143-1298

78132391 5/5/98, 8:34 AM16