NEC LCD1525V User Manual 2

NEC LCD Series

MultiSync

™

LCD

User’s Manual

1525V

You can

product online at

www.nectech.com/

productregistration

78134641.wpc 5/4/99, 5:37 PM1

Index

Warning 1 Contents 2 Quick Start 3-5 Controls 6-7 Recommended Use 8-9 Specifications 10 Features 11 Troubleshooting 12 References 13 Limited Warranty 14 TCO’99 15-16

Avertissement 17 Contenu 18 Mise en marche rapide 19-21 Commandes 22-23 Usage recommandé 24-25 Fiche technique 26 Fonctions 27 Dépannage 28 Références 29 Garantie limitée 30 TCO’99 31-32

78134641.wpc 5/4/99, 5:37 PM2

WARNING

TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT USE THIS UNIT'S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE PRONGS CAN BE FULLY INSERTED. REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK • DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This

symbol warns user that uninsulated voltage within the unit may have sufficient magnitude to cause

electric shock. Therefore, it is dangerous to make any kind of contact with any part inside this unit.

This symbol alerts the user that important literature concerning the operation and maintenance of this unit has been included. Therefore, it should be read carefully in order to avoid any problems.

Canadian Department of Communications Compliance Statement

DOC: This Class B digital apparatus meets all requirements of the Canadian Interference-

Causing Equipment Regulations.

C-UL: Bears the C-UL Mark and is in compliance with Canadian Safety Regulations

according to C.S.A. C22.2 No. 950.

FCC Information

Use the attached specified cables with the LCD1525V radio and television reception. (1)

Please use the supplied power cable or equivalent to ensure FCC compliance. (2) Please use the supplied AC Adapter. (3) Shielded video signal cable.

Use of other cables and adapters may cause interference with radio and television

reception.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver

is connected.

• Consult your dealer or an experienced radio/TV technician for help.

If necessary, the user should contact the dealer or an experienced radio/television technician for additional suggestions. The user may find the following booklet, prepared by the Federal Communications Commission, helpful: ”How to Identify and Resolve Radio-TV Interference Problems.“ This booklet is available from the U.S. Government Printing Office, Washington, D.C., 20402, Stock No. 004-000-00345-4.

color monitor so as not to interfere with

78134641.wpc 5/4/99, 5:37 PM3

Contents

You can register your product online at www.nectech.com/productregistration

Your new NEC Technologies MultiSync® LCD monitor box* should contain the following:

• MultiSync LCD1525V monitor with tilt base

• Power Cord

• AC Adapter

• Video Signal Cable

• User’s Manual

MultiSync LCD1525V monitor with Video Signal Cable and AC Adapter

™

1525V

MultiSync

LCD

1525V

Power Cord

r’s M

User’s Manual

* Remember to save your original box and packing material to transport or ship the monitor.

78134641.wpc 5/4/99, 5:37 PM4

Quick Start

To attach the MultiSync® LCD monitor to your system, follow these instructions:

1. Turn off the power to your computer.

2. For the PC: Connect the 15-pin mini D-SUB of the appropriate signal cable

to the connector of the display card in your system (Figure A.1). Tighten all screws. For the Mac: Connect the MultiSync LCD

(Figure B.1). Attach the 15-pin mini D-SUB end of the appropriate signal cable to the MultiSync LCD

NOTE: To obtain the MultiSync LCD

call NEC Technologies at (800) 820-1230.

Remove connector cover and cable cover on back of monitor.

3. Connect the 15-pin mini D-SUB of the video signal cable to the appropriate connector on

the back of the monitor (Figure C1). Place the Video Signal Cable under Clip A. Then place AC Adapter Cable under Clip B. Replace connector cover and cable cover.

NOTE: Incorrect cable connections may result in irregular operation, damage

display quality/components of LCD module and/or shorten the module’s life.

4. Connect one end of the power cord to the MultiSync LCD Series monitor and the other

end to the power outlet (Figure D.1).

5. Turn on the monitor (Figure E.1) and the computer.

To complete the setup of your MultiSync LCD monitor, use the following OSM™ controls:

• Auto Adjust Contrast

• Auto Adjust

Refer to the Controls section of this User’s Manual for a full description of these OSM controls. NOTE: For download information on the Windows 95/98 INF file for your MultiSync

LCD

NOTE: If you have any problems, please refer to the Troubleshooting section of

this User’s Manual.

1525V Macintosh cable adapter (Figure B.1). Tighten all screws.

1525V Macintosh cable adapter,

1525V monitor, refer to the References section of this User’s Manual.

™

1525V

Macintosh cable adapter to the computer

Figure A.1 Figure B.1

78134641.wpc 5/4/99, 5:37 PM5

15-pin mini D-SUB

Mac Adapter (not included)

15-pin

mini

D-SUB

Quick Start cont.

Figure C.1

Clip B

Figure D.1

Clip A

Power Switch

78134641.wpc 5/4/99, 5:37 PM6

Figure E.1

lti

+ 12 hidden pages