NEC IPX Wireless User Guide

NDA-24313

ISSUE 1

STOCK # 200817

®

Wireless Features and Specifications

OCTOBER, 2000

NEC America, Inc.

LIABILITY DISCLAIMER

NEC America, Inc. reserves t he right to chan ge the specific ations, funct ions, or
features, at any time, without noti ce.

NEC America, Inc. has prepared this document for use by its employees and
customers. The information contained herein is the property of NEC America,
Inc. and shall not be reproduced without prior written approval from NEC
America, Inc.

NEAX

®

and D

term®

are registered trademarks of NEC Corporation.

2000

NEC America, Inc.

Printed in the U.S.A

PAGE No.

i 1
ii 1
1 1
2
3 1
4 1
5 1
6
7 1
8 1
9 1

10
11 1
12 1
13 1
14
15 1
16 1
17 1
18
19 1
20 1
21 1
22
23 1
24 1
25 1
26
27 1
28 1
29 1
30
31 1
32 1
33 1
34
35 1
36 1

DATE OCTOBER, 2000 DATE DATE DATE

DATE DATE DATE DATE

12345678

1

1

1

1

1

1

1

1

1

ISSUE 1 ISSUE 2 ISSUE 3 ISSUE 4

ISSUE 5 ISSUE 6 ISSUE 7 ISSUE 8

ISSUE No.

PAGE No.

37 1
38
39 1
40 1
41 1
42
43 1
44 1
45 1
46
47 1
48 1
49 1
50
51 1
52 1
53 1
54
55 1
56 1
57 1
58
59 1
60 1
61 1
62
63 1
64 1
65 1
66
67 1
68 1
69 1
70
71 1
72 1
73 1
74

12345678

1

1

1

1

1

1

1

1

1

1

ISSUE No.

NEAX2400 IPX
Wireless Features and Specifications

Revision Sheet 1/1

NDA-24313

NDA-24313

ISSUE 1

OCTOBER, 2000

NEAX2400 IPX

Wireless Fe atu r es an d S pe cif ica tio n s

Feature List

Page

Wireless Specification in NEAX2400 IPX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Wireless Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

General Service Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

R-50 Radio Channel Changeover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

S-130 Speech Scrambling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

O-38 Out Of Cell Indication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

A-131 Automatic Release - Out Of Cell Calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

P-61 PS Authentication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

P-62 PS Location Registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

O-39 Overlap Dialing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

P-63 Preset Dialing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

I-39 Individual PS Calling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

H-23 Handover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

D-154 DTMF Signal Sender . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

C-156 Consultation Hold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

F-34 Flexible PS Numbering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

P-64 PS Service Class . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

P-65 PS Restriction Class . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

P-66 PS-to-Station Calling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

S-131 Stack Dialing - Station . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

S-132 Speed Calling - Station . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

A-128 Automatic Announcement - Disconnected PS Out Of Zone . . . . . . . . . . . . . . . . 44

A-129 Automatic Announcement - Called PS Out of Zone . . . . . . . . . . . . . . . . . . . . . . . 45

C-155 Call Forwarding PS Incoming Call Incomplete . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

D-155 D

N-43 Name Display - Intra-Node Call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

N-44 Name Display - Intra-Node Call - CCIS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

N-45 Number Sharing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

V-24 Voice Mail Indication (VMI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

W-8 Wireless Analog Adjunct Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

I-41 ISDN Roaming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

C-161 Call Forwarding - Dropped Calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

I-40 ISDN Data Communications - 32 kbps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

A-137 Authorization C ode - D
C-166 Call Park - D

G-23 Group Call - Automatic Conference (20-Party) . . . . . . . . . . . . . . . . . . . . . . . . . . 66

S-134 Short Text Messaging Service (STM Service) . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

term

PSII Two Line Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

term

term

PSII . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

PSII . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

Movement of PS in NEAX2400 IPX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

NEAX2400 IPX Wireless Features and Specifications
NDA-2431 3, Is sue 1

Page i

This page is for your notes.

Page ii

NEAX2400 IP X W i reless Features an d S pe cifications

NDA-24313, Issue 1

Wireless Specification in NEAX2400 IPX

Wireless Specification in NEAX2400 IPX

Acronym Name Range Conditions Remarks

Wireless

PCN

Community
Number

ERN

Calling Area
Number

GRN Group Number

CSN ZT Number

PS

Maximum number
of PSs

1 - 1024/

FCCS network

1 - 32/PCN (defined

by the Wireless

System standard)

1 - 8/ERN (defined by

the Wireless System

standard)

1 - 32/GRN (defined

by the Wireless

System standard)

4000 PSs/node

In FCCS network,

there is no limitation

within the limit of

maxim um FCCS

ports and the

capability of NDM.

Can be assigned over

the node.

Cannot be assigned

over the node.

The value is the total

number of the actual

PSs and the

tem porar y num b e rs

for Visitors, and it is

possible to use both

as actual or

temporary.

Maximum 32 nodes can be
covered in the identical PCN,
even if one ERN is a ssigned in
a node.

term

PSII Two Line

D
Operation se rv i ce use s 2 PS
resources.

4 ZTs/CS-INT
Maximum number
of ZTs

ZT

Number of
B-channels

12 CS-INT s / PIM

Maximum 768 ZTs/

4-IMG system

3 voice channels of

32 Kbps/ZT

• ZT -ID (SY S-ID and Ad d i t ional ID)

29 bits

SYS-ID: PCN = 1: 1 ERN GRN CSN

42 bits

The number of CS-INTs in a
PIM is 12 with power supply.

13 bit s

53

5

NEAX2400 IPX Wireless Features and Specifications
NDA-24313, Issue 1

Page 1

Wireless Specification in NEAX2400 IPX

The following figure shows zone setting.

Assign c al lin g ar e a ov er the node i s not allow ed.

When the FC CS netw o rk is esta bl is he d, inter -no de

Hand- O v er is available within an ide nti cal PCN.

ERN-1-1

ERN-1-2

ERN-1-3

ERN-2-2

ERN-2-1

ERN-2-3

Node 1 Node 2

PCN-1

ERN-1-4

ERN-1-5

ERN-2-4

ERN-2-5

PCN-2

Service Conditions

Below are some of the conditi ons for the u se of the Built-in Wireless system (IPX ).

1. Wireless s y s tem is not available in the Hotel system. (Will be available in the future.)

2. ACD/OAI services are not available with the Wireles s s ystem.

3. Series 7200 or later software is necessary for Wireless system operation.

4. SMDR equipment can be used for billing.

5. The following billing services are available in the Wireless system:

• SMDR for outgoing C.O. line

• SMDR for incoming C.O. line

• SMDR for outgoing Tie line

• SMDR for incoming Tie line

• SMDR for incoming DID

• SMDR for DIT

• SMDR for IC via ATT-CON

6. PS is not connected to the data terminal equipment. (Will be available in the future.)

7. Service Conditions for CCIS features are as follows:
a.) When a call is originated from or terminated to a PS via CCIS, the calling number sent to the

called station varies depending on the numbering plan as shown below.

• closed numbering network: telephone number (PS number)

• open numbering network: office code + telephone number (PS number)

b.) When a PS user has a call placed on hold, link re-connection is not perfo rmed.

ERN-1-6

ERN-2-6

Page 2

NEAX2400 IPX Wireles s Featu re s and S pe cificat io ns

NDA-24313, Issue 1

Wireless Features

FEATURE NAME REMARKS

Dynamic Radio Channel Control

R-50* Radio Channel Changeover

S-130* Speech Scr amb l i n g

Service Area Assignment

O-38* Out of Cell Indication

A-131* Automatic Release-Out of Cell Calls

P-61* PS Authentication
P-62* PS Location Registration

O-39* Overlap Di al ing

P-63* Preset Dialing

I-39* Individual PS Calling

Wireless Features

H-23* Handover

D-154* DTMF Signal Sender

C-156* Consultation Hold

F-34* Flexible PS Numbering
P-64* PS Service Class
P-65* PS Restriction Class

Radio Paging Channel Distribution

P-66* PS-to-Station Calling
S-131* Stack Dialing - Station
S-132* Speed Calling - Station

Volume Control
Batt ery Display
Receive RF Power Display
Any Key Answer Not available for D
Automatic Answer
Key Lock

term

PSII

NEAX2400 IPX Wireless Features and Specifications
NDA-24313, Issue 1

Page 3

Wireless Features

FEATURE NAME REMARKS

Peg Counts (per four transceivers):
Number of call originations attempted
Number of call originations completed
Number of call terminations attempted
Number of call terminations completed
Traffic-ch Fault Report
Number of Out of Cell Release Calls
Radio Channel Changeover
Handover Count

A-128*

A-129*

C-155*

D-155*D

Automatic Announcement ­Disconnected PS Out of Zone

Automatic Announcement - Called PS
Out of Zone

Call Forwarding PS Incoming Call
Incomplete

term

PSII Two Line Operation

N-43* Name Display - Intra-node Call
N-44* Name Display - Intra-node Call - CCIS
N-45* Number Sharing
V-24* Voice Mail Indication (VMI)

W-8* Wireless Analog Adjunct Connection
I-41* ISDN Roaming

C-161* Call Forwarding - Dropped Calls

I-40* IS D N Da ta Communications - 32 kbps

term

A-137* Authorization Code - D

term

C-166*Call Park - D

PSII

PSII

The C.O. Incoming calls are subject to charging.

G-23*

S-134*

Page 4

Group Call - Automatic Conference
(20-Party)

Short Text Messaging Service (STM
Service)

NEAX2400 IPX Wireles s Featu re s and S pe cificat io ns

NDA-24313, Issue 1

General Service Features

General Service Features

Series 7300 Series 7400

Stand Alone FCCS Stand Alone FCCS

Index Feature Name

A-18 Account Code — — — — — — — —
A-52 Account Code - Attendant — — — — — — — —
A-77Accunet Access ————————

A-12 1 Add on Conference - 8 P arty — — — — — — — —

Advice of Charge - Receipt and

A-136

A-53 All Zone Paging — — — — — — — —
A-16 Alternate Routing — — — — — — — —
A-76 Alternate Routing - PRI X — — — → ———

A-125 Analog CALLER ID (Class SM) — — — — — — — —
A-127 Analog CALLER ID - Station — — — — — — — —
A-126 ANI - CCIS (16 digit) — — — — — — — —

A-15 Announcement Service X — — — → ———
A-59 Announcement Service - Attendant — — — — — — — —
A-92 Announcement Service - PRI — — — — — — — —
A-98 Answer Hold - Attendant — — — — — — — —
A-24 Asynchronous Data Switc hing — — — — — — — —
A-44 Asynchronous Data Switc hing - CCIS — — — — — — — —

A-1

A-45

A-3 Attendant Console — X — X — → — →
A-2 Attendant-Controlled Conference — X — X — → — →

A-46

A-4Attendant Key Pad ————————
A-5Attendant Lockout ————————
A-6 Attendant Loop Release — — — — — — — —

A-19 Attendant Night Transfer X — — — → ———

A-105 Attendant Overflow — — — — — — — —

A-7Attendant Override ————————

A-38 Attendant-Switched Data Calls — — — — — — — —

Fm: When the call is originated from PS To: When the call terminates to PS
X: Available —: Not available
X*: Available with limitations

Display of AOC from a Foreign Q-SIG
Network

Attendant Camp-On with Tone
Indication

Attendant Camp-On with Tone
Indication - CCIS

Attendant-Controlled Conference ­CCIS

Fm To Fm To Fm To Fm To

————

————————

————————

—X—X—→ — →

NEAX2400 IPX Wireless Features and Specifications
NDA-24313, Issue 1

Page 5

General Service Features

Series 7300 Series 7400

Stand Alone FCCS Stand Alone FCCS

Index Feature Name

A-60 Attendant-to-Attendant Calling — — — — — — — —
A-17 Audible Indication Control — — — — — — — —
A-20Authorization Code ————————

A-99

A-29

Authorization Code Display
Elimination

Authorization Code - Tie Line

Incoming
A-82 Automated Attendant —
A-88 Automatic Call Distribution - PRI — — — — — — — —

A-55 Automatic Change of Night Service — — — — — — — —
A-94 Automatic Cir cuit Assurance - PRI X — — — → ———
A-41 Automatic Disconnection of Data Calls — — — — — — — —
A-69Automatic Idle Return ——————— —
A-30 Automatic/Manual Intercom — — — — — — — —
A-42 Automatic Modem Pool Selection — — — — — — — —

A-78

A-87

Automatic Number Identification

(ANI)

Automatic Number Identification

(ANI) - CCIS

A-8 Automatic Recall — X* — X* — →*—→*

A-71 Automatic Recall - CCIS — X* — X* — →*—→*

A-8D Automatic Recall - D

term

A-21Automatic Trunk Test ————————
A-96 Automatic Trunk Test - PRI — — — — — — — —

Fm To Fm To Fm To Fm To

————————

————————

X

Note 1

—

X

Note 1

—

→

Note 1

—

→

Note 1

————————

————————

————————

B-17 Blind Transfer to Attendant X — X — → — → —
B-18 Blind Transfer to Station X — X — → — → —
B-13 Blocking of Trunk Usage — — — — — — — —

B-8

Boss-Secre tary Message Wait ing Lamp

Control

B-5D Boss-S ecretary Override - D

term

————————

————————
B-22 Boss-Secretary Override - PRI — — — — — — — —
B-11Boss-Secretary Transfer ————————
B-19 Boss - S ecreta ry Tr ansfer - PRI — — — — — — — —

B-6Brokerage Hot Line ————————

Fm: When the call is originated from PS To: When the call terminates to PS
X: Available —: Not available
X*: Available with limitations

Page 6

NEAX2400 IPX Wireles s Featu re s and S pe cificat io ns

NDA-24313, Issue 1

General Service Features

Series 7300 Series 7400

Stand Alone FCCS Stand Alone FCCS

Index Feature Name

B-10 Brokerage Hot Line - CCIS — X — — — → ——
B-12 Brokerage Hot Line - Outside — — — — — — — —
B-25 Brokerage Hot Line - Outside - PRI — — — — — — — —

B-2 Busy Lamp Field - Flexible X X — — →→——
B-3Busy Verification ————————
B-9 Busy Verification - CCIS — — — — — — — —

C-1Call Back ————————
C-44 Call Back - CCIS — — — — — — — —
C-73 Call Back - Delayed — — — — — — — —

C-1D Call Back - D

term

C-150Call Block ————————
C-106 Call-by-Call Pool Management — — — — — — — —
C-105 Call-by-Call Service Selection — — — — — — — —
C-152 Call Completion on No Reply (CCNR) — — — — — — — —
C-149 Call Completion to Busy Subscriber — — — — — — — —

C-5 Call Forwarding - All Calls X X

C-69

C-123

Call Forwarding - All Calls ­Announcement

Call Forwarding - All Calls ­Announcement - PRI

C-45 Call Forwarding - All Calls - CCIS X X X X →→→→

C-5D Call Forwarding - All Calls - D

C-95D

Call Forwarding - All Calls - D
PRI

term
term

-

C-28 Cal l For w ar d i ng - All Calls - Outside X X X X →→→→
C-95 Call Forwarding - All Calls - PRI X X X X →→→→

C-94

Call Forwarding - Assignment ­Atte n da nt - CC IS

C-2 Call Forwarding - Busy Line X X
C-46 Call Forwarding - Busy Line - CCIS X X X X →→→→

C-2D Call Forwarding - Busy Line - D

term

C-60 Call Forwarding - Busy Line - Outside X X X X →→→→
C-96 Call Forwarding - Busy Line - PRI X X X X →→→→

Fm: When the call is originated from PS To: When the call terminates to PS
X: Available —: Not available
X*: Available with limitations

Fm To Fm To Fm To Fm To

————————

X

Note 14

X →→

→

Note 14

→

X—X—→ — → —

————————

————————

————————

————————

X

Note 14

X →→

→

Note 14

→

————————

NEAX2400 IPX Wireless Features and Specifications
NDA-24313, Issue 1

Page 7

General Service Features

Series 7300 Series 7400

Stand Alone FCCS Stand Alone FCCS

Index Feature Name

C-3 Call Forwarding - Don’t Answer X X

C-47

C-3D

C-74

Call Forwarding - Don’t Answer ­CCIS

Call Forwarding - Don’t Answer -

term

D
Call Forwarding - Don’t Answer -

Outside

C-129 Call Forwarding - Don’t Answer - PRI X X X X →→→→

C-133

Call Forwarding - Don’t Answer to
UCD Queue

C-48 Call Forwarding - Intercept - CCIS — — — — — — — —

C-125 Call Forwarding - Intercept - PRI — — — — — — — —

C-81 Call Forw ar d ing - I’m Here — — — — X X X X

C-25

C-75

C-101

Call Forwarding - Intercept/
Announcement

Call Forwarding - Intercept/
Announcement - Attendant

Call Forwarding - Intercept/

Announcement - PRI
C-26 Call Forwarding - Override — — — — — — — —
C-49 Call Forwarding - Override - CCIS — — — — — — — —

C-158

Call Forwarding Supplementary

Service (SS-CF) with Rerouting

C-6Call Hold ————————

C-146Call Hold Conference ————————

C-6D Call Hold - D

term

C-154Call Hold Pick Up ————————

C-43Call Metering ————————
C-29Call Park ————————

C-119Call Park - PRI ————————

C-30 Call Pickup - Direct X — X — → — → —

C-102 Call Pickup - Direct - PRI X — X — → — → —

C-7 Call Pickup - Group X X

C-7D Call Pickup - Group - D

C-97D Call Pickup - Group - D

term
term

- PRI ————————

Fm: When the call is originated from PS To: When the call terminates to PS
X: Available —: Not available
X*: Available with limitations

Fm To Fm To Fm To Fm To

X

Note 14

X →→

→

Note 14

→

XXXX→→→→

————————

X

Note 2X Note 2X Note 2X Note 2→ Note 2→ Note 2→ Note 2→ Note 2

XXXX→→→→

X———→ ———

————————

————————

————

————————

X

Note 15XNote 15

→→

→

Note 15→Note 15

————————

Page 8

NEAX2400 IPX Wireles s Featu re s and S pe cificat io ns

NDA-24313, Issue 1

General Service Features

Series 7300 Series 7400

Stand Alone FCCS Stand Alone FCCS

Index Feature Name

C-97 Call Pickup - Group - PRI X X

C-8 Call Processing Indication X X X X →→→→

C-53 Call Processing Indication - CCIS X X X X →→→→

C-9 Call Queuing X — X — → — → —

C-151Call Return ————————
C-160Call Trace ————————

C-11 Call Transfer - All Calls X X* X X* →→* →→*
C-50 Call Transfer - Al Calls - CCIS X X X X →→→→

C-11D Call Transfer - All Calls - D
C-99D Call Transfer - All Calls - D

term

term

- PRI————————

C-99 Call Transfer - All Calls - PRI X X X X →→→→
C-10 Call Transfer - Attendant
C-54 Call Transfer - Attendant - CCIS X X X X →→→→

C-98 Call Transfer - Attendant - PRI X X X X →→→→

C-159

Call Transfer Supplementary Service

(SS-ST) with Rerouting
C-31 Cal l Wait ing - Originat ing

C-12 Call Waiting - Terminating

C-114 Call Waiting - Terminating - PRI — X — X — → — →

C-27D Call Waiting Answer - D

term

C-13 Call Waiting Lamp X — X — → — → —
C-76 Call Waiting Lamp - UCD — — — — — — — —
C-59 Called Number Display - Attendant — — — — — — — —
C-51 Called Station Status Display - CCIS — — — — — — — —

C-22D Called Station Status Display - D

term

Calling Name Identification

C-153

Presentation (CLIP) / Connected Name

Ident ifi cation Pr esentat io n (C O N P )
C-52 Calling Number Display - CCIS X X X X →→→→

C-24D Calling Number Display - D

term

C-112 Calling Party Information Transfer — — — — — — — —

C-157

Calling Party Number - Name

Assignment and Display

Fm: When the call is originated from PS To: When the call terminates to PS
X: Available —: Not available
X*: Available with limitations

Fm To Fm To Fm To Fm To

X

Note 15XNote 15

→→

→

Note 15→Note 15

————————

X

Note 3X Note 3X Note 3XNote 3→Note 3→Note 3→Note 3→Note 3

————

X

Note 4X Note 4X Note 4X Note 4→Note 4→Note 4→Note 4→Note 4

X

Note 4X Note 4X Note 4X Note 4→Note 4→Note 4→Note 4→Note 4

————————

————————

————————

————————

————————

NEAX2400 IPX Wireless Features and Specifications
NDA-24313, Issue 1

Page 9

General Service Features

Series 7300 Series 7400

Stand Alone FCCS Stand Alone FCCS

Index Feature Name

Calling Party R ecognitio n Service (Call

C-103

Forwarding - All Calls/Busy Line/

Don’t Answer)

C-104

Calling Party Recognition Service

(DIT)

C-163 CCIS Networking via IP — — — —

CCIS Tandem Call - Calling Party

C-164

Number (CPN) Delivery to ISDN &

Q-SIG Networks
C-14 CCSA Access X — — — → ———
C-20 Centralized Attendant Service (CAS) — — — — — — — —
C-55 Centralized Billing - CCIS X — X — → — → —

C-56

Centralized Day/Night Mode Change -

CCIS

C-167 Centralized Maintenance - CCIS — — — —

C-57

Centralized System Management

Report - CCIS

C-109 Centrex C ompa ti bility — X — X — → — →

C-15 Class of Service - Individual X X X X →→→→
C-21 Code Calling Access X — X — → — → —

C-41

Combined Cabl e Pa ir for Simulta neo u s

Voice and Data
C-33 Consecutive Dialing - Attendant — — — — — — — —
C-62 Consecutive Speed Calling - System — — — — — — — —
C-17 Consultation Hold - All Calls X X X X →→→→
C-58 Consultation Hold - All Calls - CCIS X X X X →→→→

C-17D Consultation Hold - All Calls - D

term

C-100D Consultation Hold - All Calls - D - PRI — — — — — — — —

C-100 Consultation Hold - All Calls - PRI X X X X →→→→

Fm To Fm To Fm To Fm To

————————

————————

————

————————

————————

————————

————————

D-152 D Channel Backup - PRI — — — — — — — —

D-43 Data Call Dial Monitor — — — — — — — —
D-33 Data Call Hunting - Circular — — — — — — — —
D-34 Data Call Hunting - Secretarial — — — — — — — —
D-35 Data Call Hunting - Termina l — — — — — — — —

D-49

Data Call Least Cost Routing - 3/6-

Digit

————————

Fm: When the call is originated from PS To: When the call terminates to PS
X: Available —: Not available
X*: Available with limitations

Page 10

NEAX2400 IPX Wireles s Featu re s and S pe cificat io ns

NDA-24313, Issue 1

General Service Features

Series 7300 Series 7400

Stand Alone FCCS Stand Alone FCCS

Index Feature Name

D-36 Data Call Number Display — — — — — — — —
D-37 Data Call Origination — — — — — — — —
D-50Data Call Peg Count ————————
D-38 Data Call Progress Re sponses — — — — — — — —

D-51

Data Call Restriction from Ou tgoing

Calls
D-52 Data Call Route Advance — — — — — — — —
D-59 Data Call Toll Restriction - 3/6-Digit — — — — — — — —
D-40 Data Class of Service - Individual — — — — — — — —
D-41 Data Communication - CCIS — — — — — — — —

D-121 Data Communications - PRI — — — — — — — —

D-28 Data Communications - T1 Link — — — — — — — —
D-39 Data Connectio n - CCSA — — — — — — — —
D-47 Data Connection - FX — — — — — — — —
D-61 Data Connection - WATS Access — — — — — — — —

D-44

D-45

D-46

Data Connection - Dir ect-In

Termination

Data Connection - Dir ec t Inward

Dialing (DID)

Data Connectio n - Dir ect Outward

Dialing (DOD)
D-58 Data Connection - Tie Line Access — — — — — — — —
D-42 Data Day/Night Class of Service — — — — — — — —
D-77Data Hot Line ——————— —
D-86 Data Hot Line - CCIS — — — — — — — —
D-78 Data Hot Line - Outside — — — — — — — —
D-18 Data Interface - Automatic Answer — — — — — — — —

D-65

D-119

Data Interface - Automatic Answer -

CCIS

Data Interface - Automatic Answer -

PRI
D-48Data Interface - Manual Answer ————————

D-56

Data Line - Moves, Additions and

Changes
D-12Data Line Security ————————
D-66 Data Line Security - CCIS — — — — — — — —

Fm: When the call is originated from PS To: When the call terminates to PS
X: Available —: Not available
X*: Available with limitations

Fm To Fm To Fm To Fm To

————————

————————

————————

————————

————————

————————

————————

NEAX2400 IPX Wireless Features and Specifications
NDA-24313, Issue 1

Page 11

General Service Features

Series 7300 Series 7400

Stand Alone FCCS Stand Alone FCCS

Index Feature Name

D-117 Data Line Security - PRI — — — — — — — —

D-67Data Privacy - CCIS ————————
D-17Data Privacy on Demand ————————
D-68 Data Privacy on Demand - CCIS — — — — — — — —

D-118 Data Privacy on Demand - PRI — — — — — — — —
D-126 Data Queuing — — — — — — — —

D-53 Data Switching through Data Module — — — — — — — —
D-54 Data Switching through D

term

D-55 Data System - Diagnostic Tests — — — — — — — —
D-57 Data Tenant Service — — — — — — — —
D-21 Data Termina l Traffic Measurement — — — — — — — —
D-19Data Transparency ————————
D-69 Data Transpa rency - CCIS — — — — — — — —

D-120 Data Transp arency - PRI — — — — — — — —

D-60 Data Uniform Numbering Plan — — — — — — — —

D-122 Data Uniform Numbering Plan - PRI — — — — — — — —

D-15 Day/Night Class of Service — — — — — — — —

D-114 Delay Announcement - Attendant — — — — — — — —

D-31 Delay Announcement - UCD — — — — — — — —

D-90D De layed Ringing - D

term

D-70 Deluxe Traveling Class Mark - CCIS X X X X →→→→

D-2 Dial Access to Attendant

D-71 Dial Access to Attendant - CCIS X — X — → — → —
D-87Dial Intercom ————————

D-13D Dial Monitor - D

term

D-91 Dialed Number Display Recall - CCIS X X X X →→→→

D-3 Dictation Access X X X X →→→→

D-123 DID Addressing — X — X — → — →

D-5 Digital Display - Station X X X X →→→→

D-72 Digital Display - Station - CCIS X — X — → — → —

D-6Digital Display - Trunk ————————
D-73 Digital Display - Trunk - CCIS — — — — — — — —
D-62 Digital Line Switching — — — — — — — —
D-16 Direct Digital Interface — — — — — — — —

Fm: When the call is originated from PS To: When the call terminates to PS
X: Available —: Not available
X*: Available with limitations

Fm To Fm To Fm To Fm To

————————

————————

X

Note 5

—

X

Note 5

—

→

Note 5

—

→

Note 5

—

————————

Page 12

NEAX2400 IPX Wireles s Featu re s and S pe cificat io ns

NDA-24313, Issue 1

General Service Features

Series 7300 Series 7400

Stand Alone FCCS Stand Alone FCCS

Index Feature Name

D-7 Direct-In Termination (DIT) —

D-137 Direct-In Termination (DIT) - PRI —

D-74 Direct-In Termination - CCIS —

D-8 Direct Inward Dialing (DID) — X — X — → — →

D-9 Direct Outward Dialing (DOD) X — — — → ———

D-149 Direct Station Selection (DSS) Console — — — — — — — —

D-10 Distinctive Ringing —

D-153 Distinctiv e Ringing - Caller — — — — — — — —

D-75 Distinctive Ringing - CCIS —

D-115 Distinctive Rin ging - PRI — — — — — — — —

D-76 Do Not Disturb - CCIS — X — X — → — →

D-11D Do Not Disturb - D
D-76D Do Not Disturb - D

D-116D Do Not Disturb - D

D-32D Dual H old - D
D-93D Dual H old - D

term
term

- CCIS ————————

term

- PRI ————————

term
term

- CCIS ————————

D-156 Dual Station Call — — — —

Fm To Fm To Fm To Fm To

X

Note 6

X

Note 6

X

Note 6

X

Note 7

X

Note 7

—

—

—

—

—

X

Note 6

X

Note 6

X

Note 6

X

Note 7

X

Note 7

—

—

—

—

—

→

Note 6

→

Note 6

→

Note 6

→

Note 7

→

Note 7

—

—

—

—

—

→

Note 6

→

Note 6

→

Note 6

→

Note 7

→

Note 7

————————

————————

E-18 E 911 - ANI Unified Number of Digits — — — — — — — —

E-20

E911 - ANI Unified Number of Digit s ­CCIS

————————

E-7EIA RS232C Interface ————————

E-9Elapsed Time Display - CCIS ————————

E-3D Elapsed Time Display - D

E-14D Elapsed Time Display - D

term

————————

term

- PRI ————————
E-11Emergency Call ————————
E-23 Event Bas ed CCIS - IS D N Transpor t — — — — — — — —
E-24 E vent Based CCIS - Q-SIG Transport — — — —

E-4D Exclusive Hold - D

term

————————
E-1 Executive Right of Way — — — — — — — —
E-8 Executive Right of Way - CCIS — — — — — — — —

E-1D Executive Right of Way - D

term

————————

Fm: When the call is originated from PS To: When the call terminates to PS
X: Available —: Not available
X*: Available with limitations

NEAX2400 IPX Wireless Features and Specifications
NDA-24313, Issue 1

Page 13

General Service Features

Series 7300 Series 7400

Stand Alone FCCS Stand Alone FCCS

Index Feature Name

E-26

Expanded Multiple Line Operation -

term

D

F-6 Faulty Trunk Report X X — — →→——

F-26 Faulty Trunk Report - PRI — — — — — — — —

F-36 FCCS Netw orking via IP — — — —
F-3D Flash Button - D
F-4D Flash Entry - D

F-17

Flexible Assignment of Line/Function
Buttons

term

term

F-11Flexible Numbering of DTEs ————————

F-1 Flexible Numbering of Stations X X X X →→→→
F-12 Flexible Numbering of Stations - CCIS X X X X →→→→
F-21 Flexible Numbering of S tations - PRI X X X X →→→→

F-5D Flexible Ringing Assignment - D

term

F-35 Flexible Rou ting - FCCS X — X — → — → —
F-31 Follow Phone — — — — — — — —

F-7 Forced Account Code — — — — — — — —

F-2 FX Access X — — — → ———

Fm To Fm To Fm To Fm To

————

————————
————————

————————

————————

G-2 Group Calling — — — — — — — —

H-7 Ha lf/Full Duplex Switchover — — — — — — — —
H-4Hands-Free Answer Back ————————

H-10 Hands-Free Answer Back - CCIS — — — — — — — —

H-4D Ha nds-Free Answer Back - D

H-14D Ha nds-Free Answer Back - D

H-5D Hands-Free Dialing /Moni toring - D

term

————————

term

- PRI————————

term

————————

H-1 Hot Line X X — — →→——

H-12 Hot Line - CCIS X — — — → ———

H-9 Hot Line - Outside X — — — → ———

H-15 Hot Line - Outside - PRI X — — — → ———

H-2 House Phone — — — — — — — —

H-11 House Phone - CCIS — X — X — → — →

Fm: When the call is originated from PS To: When the call terminates to PS
X: Available —: Not available
X*: Available with limitations

Page 14

NEAX2400 IPX Wireles s Featu re s and S pe cificat io ns

NDA-24313, Issue 1

General Service Features

Series 7300 Series 7400

Stand Alone FCCS Stand Alone FCCS

Index Feature Name

I-7D I-Hold Indication - D
I-8D I-Use Indication - D

term

————————

term

————————

I-20 Immediate Ringback Tone X — — — → ———

I-1 Immediate Ringing — — — — — — — —
I-2 Incoming Call Identification — — — — — — — —

I-16 Incoming Call Identification - CCIS X — X — → — → —
I-24 Incoming Call Identification - PRI — — — — — — — —

I-3

I-25

Incoming Central Office Call to Tie
Line Connec tion

Incoming ISDN Call to Tie Line
Connection - PRI

I-26 Indialing through Main - PRI — — — — — — — —

I-6 Individual Attendant Access X — X — → — → —

I-17 Individual Attendant Access - CCIS X — — — → ———

I-4 Individual Trunk Access — — — — — — — —

I-19 Individual Trunk Access - CCIS — — — — — — — —

I-9 Intercom Calling — — — — — — — —

I-10D

Intermediate Station Number Display -

term

D
I-21 Internal Zone Paging — — — — — — — —
I-11 Inter-Office Off-Hook Queuing — — — — — — — —
I-36 Inter-Office Off-Hook Queuing - PRI — — — — — — — —

I-27

Inter-PBX Coordinated Station

Numbering Plan - PRI

I-5 Inter-Position Transfer — — — — — — — —
I-18 Inter-Position Transfer - CCIS — — — — — — — —
I-15 Inter-Modem Pooling — — — — — — — —

I-28

ISDN Individual Calling Line
Identification (ICLID)

Fm To Fm To Fm To Fm To

————————

————————

————————

————————

————————

K-1D

Keyboard Dialing - Data Adapter-

term

D

————————

K-2 Keyboard Dialing - Data Module — — — — — — — —
K-3Keypad Dialing ————————

L-1Lamp Check ————————

Fm: When the call is originated from PS To: When the call terminates to PS
X: Available —: Not available
X*: Available with limitations

NEAX2400 IPX Wireless Features and Specifications
NDA-24313, Issue 1

Page 15

General Service Features

Series 7300 Series 7400

Stand Alone FCCS Stand Alone FCCS

Index Feature Name

L-6 Last Number Call

L-6D Last Number Call - D

L-42D Last Number Call - D

term

————————

term

- PRI ————————

L-42Last Number Call - PRI ————————

L-33

L-34

LCR - Attendant Manual Override ­PRI

LCR - Automatic Overflow to DDD ­PRI

L-35 LCR - Clocked Manual Override - PRI X — — — → ———

L-49

LCR - Special Line Warning Tone -

PRI
L-10 LCR - Time of Day Routing — — — — — — — —
L-32 LCR - Time of Day Routing - PRI — — — — — — — —
L-28 L DN - Night Connection — — — — — — — —
L-29 L DN - Night Connection - CCIS — X — X — → — →
L-30 L DN - Night Connection - Outside — — — — — — — —

L-46

LDN - Night Connection - Outside -

PRI
L-44 L DN - Night Connection - PRI — — — — — — — —

L-5 Least Cost Routing (LCR) - 3/6-Digit X — X — → — → —

L-31

Least Cost Routing (LCR) - 3/6-Digit -

PRI
L-11 Line Load Control - Attendant — — — — — — — —
L-20 Line Load Control - Automatic — — — — — — — —
L-21 Line Load Control - MAT — — — — — — — —

L-3Line Lockout ————————
L-9D Line Preselection - D
L-8D Line Reconnect - Other Line - D
L-7D Line Reconnect - Same Line - D

L-24

Listed Directory Number Display ­Attendant

term

term

term

L-25 Look Ahead Routing - CCIS — — — — — — — —

Fm To Fm To Fm To Fm To

—

Note 8—Note 8—Note 8—Note 8—Note 8—Note 8—Note 8—Note 8

————————

X———→ ———

————————

————————

X—X—→ — → —

————————
————————
————————

————————

M-18

Maintenance Adm inistration Termina l
(MAT)

————————

M-15 Maintenance Printout — — — — — — — —

Fm: When the call is originated from PS To: When the call terminates to PS
X: Available —: Not available
X*: Available with limitations

Page 16

NEAX2400 IPX Wireles s Featu re s and S pe cificat io ns

NDA-24313, Issue 1

General Service Features

Series 7300 Series 7400

Stand Alone FCCS Stand Alone FCCS

Index Feature Name

M-31 Manual Disconnection of Data Call — — — — — — — —
M-47 Manual Signaling — — — — — — — —

M-1 Meet-Me Paging X — X — → — → —

M-11 Meet-Me Paging - Attendant — — — — — — — —
M-77 Megacom 800 Access — — — — — — — —
M-76Megacom Access ————————
M-26 Message Cente r Interface — — — — — — — —
M-67 Message Center Interface - CCIS — — — — — — — —
M-19 Message Reminder — — — — — — — —
M-34 Message Reminder - CCIS — — — — — — — —

M-19D Message Reminder - D
M-34D Message Reminder - D
M-85D Message Waiting Indication - D

M-23

M-35

M-30

M-36

Message Waiting Lamp Setting ­Attendant

Message Waiting Lamp Setting ­Atte n da nt - CC IS

Message Waiting Lamp Setting ­Station

Message Waiting Lamp Setting ­Station - CCIS

term

————————

term

- CCIS ————————

term

————————

M-101MF ANI to SMDR ————————

M-84MF Signaling - DID ————————

M-2 Miscel laneous Trunk Access X — X — → — → —
M-37 Miscellaneous Trunk Access - CCIS X — X — → — → —
M-71 Miscellaneous Trunk Access - PRI X — X — → — → —

M-3 Miscellaneous Trunk Restriction X — X — → — → —

M-38

Miscellaneous Trunk Restriction ­CCIS

M-72 Miscellaneous Trunk Restriction - PRI X — X — → — → —
M-39 Modem Pooling - CCIS — — — — — — — —
M-74 Modem Pooling - PRI — — — — — — — —
M-48 Multi Channel Recording X — X — → — → —
M-44 Multiple Call Forwarding - All Calls X X X X →→→→

M-40

Multiple Call Forwarding - All Calls ­CCIS

Fm: When the call is originated from PS To: When the call terminates to PS
X: Available —: Not available
X*: Available with limitations

Fm To Fm To Fm To Fm To

————————

————————

————————

————————

X—X—→ — → —

XXXX→→→→

NEAX2400 IPX Wireless Features and Specifications
NDA-24313, Issue 1

Page 17

General Service Features

Series 7300 Series 7400

Stand Alone FCCS Stand Alone FCCS

Index Feature Name

M-75

Multiple Call Forwarding - All Calls ­PRI

M-24 Multiple Call Forwarding - Busy Line X X X X →→→→

M-41

M-25

M-42

Multiple Call Forwardi ng - Busy Li ne ­CCIS

Multiple Call Forwarding - Don’t
Answer

Multiple Call Forwarding - Don’t
Answer - CCIS

M-4Multiple Console Operation ————————
M-43 Multiple Console Operation - CCIS — — — — — — — —

M-20D Multiple Line Operation - D

term

————————

M-7 Music On Hold X X X X →→→→
M-73 Music On Hold - PRI X X X X →→→→

Fm To Fm To Fm To Fm To

XXXX→→→→

XXXX→→→→

XXXX→→→→

XXXX→→→→

N-9 Na iled Down Connection — — — — — — — —
N-31 Nailed Down Connection - PRI — — — — — — — —
N-37 Name Display - OAI - CCIS — — — — — — — —
N-28Name Display - System ————————
N-42 National ISDN 2 PRI X X X X →→→→
N-39 NI-1 BRI Terminal Support — — — — — — — —

N-1 Night Connection - Fixed — — — — — — — —
N-15 Night Connection - Fixed - CCIS — X — X — → — →
N-20 Night Connection - Fixed - PRI — — — — — — — —

N-2 Night Connection - Flexible — — — — — — — —
N-16 Night Connection - Flexible - CCIS — — — — — — — —
N-21 Night Connection - Flexible - PRI — — — — — — — —
N-17 Night Connection Outside - System — — — — — — — —

N-29

Night Connection Outside - System ­PRI

————————

N-3 Non-Delay Operation X — X — → — → —
N-22 Non-Delay Operation - PRI X — — — → ———

N-7D Non-Exclusive Hold - D
N-8D Non-Square Line Assignment - D

N-40

Non Facility Associated Signaling ­PRI

term

term

————————
————————

————————

Fm: When the call is originated from PS To: When the call terminates to PS
X: Available —: Not available
X*: Available with limitations

Page 18

NEAX2400 IPX Wireles s Featu re s and S pe cificat io ns

NDA-24313, Issue 1

General Service Features

Series 7300 Series 7400

Stand Alone FCCS Stand Alone FCCS

Index Feature Name

N-46 Number Portability - CCIS — — — —

O-6 Off-Hook Alarm — — — — — — — —

O-37D Off-Hook Line Number Display - D

term

O-7 Off-Hook Queuing — — — — — — — —
O-11 Off-Hook Queuing - CCIS X — X — → — → —
O-28 Off-Hook Queuing - PRI — — — — — — — —

O-1 On-Line Maintenance — — — — — — — —
O-21 Outgoing Trunk Busy - Announcement X — — — → ———

O-2 Outgoing Trunk Queuing — — — — — — — —
O-16 Outgoing Trunk Queuing - Attendant — — — — — — — —

O-30

Outgoing Trunk Queuing - Attendant ­PRI

O-12 Outgoing Trunk Queuing - CCIS — — — — — — — —

O-26

O-2D Outgoing Trunk Queuing - D

Outgoing Trunk Queuing - Deluxe ­PRI

term

————————
O-24 Outgoing Trunk Queuing - PRI — — — — — — — —
O-13 Overflow - UCD — — — — — — — —
O-32 Overflow - UCD - PRI — — — — — — — —

Fm To Fm To Fm To Fm To

————————

————————

————————

P-57Pad Lock ————————

P-1Paging Access ————————
P-28 Paging Access - CCIS — — — — — — — —
P-10 Paging Transfer — — — — — — — —
P-47 Paging Transfer - PRI — — — — — — — —

P-2Passing Dial Tone ————————

P-7 Peg Count X — — — → ———
P-37 Peg Count - P RI X — — — → ———
P-11 Periodic Time Indication Tone X — — — → ———
P-59 Personal Ringer — — — — — — — —
P-22Port Contention ————————

P-3 Power Failure Transfer

—

Note 9—Note 9—Note 9—Note 9—Note 9—Note 9—Note 9—Note 9

P-49 PRI Fail Safe Routing X — — — → ———
P-58 PRI Terminal Support (AT&T) — — — — — — — —

Fm: When the call is originated from PS To: When the call terminates to PS
X: Available —: Not available
X*: Available with limitations

NEAX2400 IPX Wireless Features and Specifications
NDA-24313, Issue 1

Page 19

General Service Features

Series 7300 Series 7400

Stand Alone FCCS Stand Alone FCCS

Index Feature Name

P-39

PRI Trunk to Tie Line Connect ion wit h
Pad Control

P-38 Primary Call Restriction - PRI X — — — → ———

P-13D Prime Line Pickup - D

term

————————

P-9 Priority Call
P-30Priority Paging ————————

P-14D Privacy - D
P-15D Privacy on All Lines - D

term

term

————————

P-18Privacy Release ————————

P-4 Pushbutton Calling — — — — — — — —

P-5 Pushbutton Calling - Attendant Only — — — — — — — —

P-6 Pushbutton-to-Rotary Conversion — — — — — — — —

Fm To Fm To Fm To Fm To

————————

X

Note 10

—

X

Note 10

—

→

Note 10

—

→

Note 10

—

————————

Q-4

Q-SIG Circuit Switched Basic Call ­ETSI Version

————————

R-16 Radio Paging — — — — — — — —

R-2 Remote Access to System —

X

Note 11

—

X

Note 11

—

→

Note 11

—

→

Note 11

R-7 Remote Maintena nce — — — — — — — —
R-3 Reserve Power — — — — — — — —

R-4 Restriction from Outgoing Calls X — — — → ———
R-22 Restriction from Outgoing Calls - CCIS X — — — → ———
R-35 Restriction from Outgoing Calls - PRI X — — — → ———
R-49Ringer Mute ————————

R-5 Rotary Dial Calling — — — — — — — —

R-6 Route Advance — — — — — — — —
R-27 Route Restriction - Announcement X — — — → ———
R-37 RS-464A PAD — — — — — — — —

S-41 Same Routing of Voice and Data — — — — — — — —

S-24D Save and Repeat - D

term

————————
S-90 SDN Access — — — — — — — —
S-42 Separate Routing of Voice and Data — — — — — — — —
S-15Serial Call ————————

Fm: When the call is originated from PS To: When the call terminates to PS
X: Available —: Not available
X*: Available with limitations

Page 20

NEAX2400 IPX Wireles s Featu re s and S pe cificat io ns

NDA-24313, Issue 1

General Service Features

Series 7300 Series 7400

Stand Alone FCCS Stand Alone FCCS

Index Feature Name

S-52Serial Call - CCIS ————————

term

S-127 Serial Call - D

————————
S-64 Serial Call Loop Release — — — — — — — —
S-53Service Display - CCIS ————————

S-25D Service Display - D
S-53D Service Display - D

term

————————

term

- CCIS ————————

S-27 Service Feature Peg Count X — X — → — → —
S-91 SID to Network - Present — — — — — — — —
S-92 SID to Network - Privacy — — — — — — — —
S-93 SID to Terminating User - Display — — — — — — — —
S-94 SID to Terminating User - DTE — — — — — — — —

S-28

S-54

S-86

Simultaneous Voice and Data
Transmission

Simultaneous Voice and Data
Transmissio n - CCIS

Simultaneous Voice and Data
Transmission - PR I

S-43 Single-Digit DTE Calling — — — — — — — —
S-19 Single-Digit Feature Code X — X — → — → —

S-1 Single-Digit Station Calling X — X — → — → —

S-55 Single-Digit Station Calling - CCIS X — X — → — → —

S-106 Slumber Time - Do Not Disturb — — — — — — — —

S-40SMDR for Data Call - RS232C ————————
S-88 SMDR for Data Call - RS232C - PRI — — — — — — — —

S-129 SMDR Output Expansion - ANI/CPN — — — — — — — —

S-33Software Line Appearance ————————

S-2 Special Dial To ne

S-23 Speed Calling - Group — — — — — — — —
S-85 Speed Calling - Group - PRI — — — — — — — —

S-26D Speed Calling - One Touch - D

term

S-61 Speed Calling Override - System — — — — — — — —
S-89 Speed Calling Override - System - PRI — — — — — — — —

S-21 Speed Calling - Station
S-84 Speed Calling - Station - PRI — — — — — — — —

Fm: When the call is originated from PS To: When the call terminates to PS
X: Available —: Not available
X*: Available with limitations

Fm To Fm To Fm To Fm To

————————

————————

————————

X

Note 12

—

X

Note 12

—

→

Note 12

—

→

Note 12

—

————————

—

Note 12—Note 12—Note 12—Note 12—Note 12—Note 12—Note 12—Note 12

NEAX2400 IPX Wireless Features and Specifications
NDA-24313, Issue 1

Page 21

General Service Features

Series 7300 Series 7400

Stand Alone FCCS Stand Alone FCCS

Index Feature Name

S-3Speed Calling - System ————————

term

S-3D Speed Calling - System - D

S-82D Speed Calling - System - D

————————

term

- PRI————————
S-82 Speed Ca lling - System - PRI — — — — — — — —
S-99 Split Call Forwarding — — — — — — — —

S-4 Splitting X X X X →→→→

S-4D Splitting - D

term

————————

S-62 Station 5dB Pad X X X X →→→→

S-6 Station-Controlled Conference X X X X →→→→

S-56 Station-Controlled Conference - CCIS — X — X — → — →

S-107 Station Individual Trunk Access - PRI X — — — → ———

S-7 Station Hunting - Circular — — — — — — — —
S-8 Station Hunting - Secretarial — — — — — — — —
S-9 Station Hunting - Terminal — — — — — — — —

S-10

S-83

Station Message Detail Recording
System

Station Message Detail Recording
System - PRI

S-11 Station-to-Station Calling X X X X →→→→
S-57 Station-to-Station Calling - CCIS X X X X →→→→

S-12

S-58

Station-to-Station Calling - Operator
Assistance

Station-to-Station Calling - Operator

Assistance - CCIS
S-44Status Display ————————
S-45 Status Indication — — — — — — — —

S-13 Step Call
S-59 Step Call - CCIS — X — X — → — →

S-95 Sub-Address - Addressing X X X X →→→→
S-96 Sub-Address - Present — — — — — — — —
S-73 Supervisory Call - CCIS — X — X — → — →
S-29 Synchronous Data Switching — — — — — — — —
S-60 Synchronous Data Switchi ng - CCIS — — — — — — — —
S-87 Synchronous Data Switchi ng - PRI — — — — — — — —

Fm: When the call is originated from PS To: When the call terminates to PS
X: Available —: Not available
X*: Available with limitations

Fm To Fm To Fm To Fm To

X—X—→ — → —

X—X—→ — → —

XXXX→→→→

XXXX→→→→

X

Note 13X Note 13X Note 13X Note 13→ Note 13→ Note 13→Note 13→ Note 13

Page 22

NEAX2400 IPX Wireles s Featu re s and S pe cificat io ns

NDA-24313, Issue 1

General Service Features

Series 7300 Series 7400

Stand Alone FCCS Stand Alone FCCS

Index Feature Name

T-1

T-37

Tandem Switching of Tie Trunks - 2/4-

Wire

Tandem Switching of Tie Trunks - 2/4-

Wire - PRI
T-12 Tenant Service X X — — →→——

T-25

Terminal Attribute Data Assignment

through MAT

T-3Tie Line Access XXXX→→→→
T-5 Tie Line Connection with Pad Control X X — X →→— →
T-2 Three-Way Calling X X X X →→→→

T-2D Three-Way Calling - D

T-38D Three-Way Calling - D

term

————————

term

- PRI ————————

T-38 T hree-Way Calling - PRI X X X X →→→→

T-18D Time Display - D

term

————————

T-62 Timed Reminder — — — — — — — —

T-6 Toll Denial/Toll Diversion X — — — → ———

T-40 Toll Denial/Toll Diversion - PRI X — — — → ———

T-7 Toll Restriction - 3/6-Digit X — — — → ———
T-26 Toll Restriction - 3/6-Digit - CCIS X — — — → ———
T-41 Toll Restriction - 3/6-Digit - PRI X — — — → ———
T-63 Tone Block — — — —
T-44 Transf er Message (TRM) — — — — — — — —

T-8 Trunk Answer from Any Station (TAS) — — — — — — — —

T-27

Trunk Answer from Any Stati on (TAS)

- CCIS

T-9 Trunk Group Busy Lamp — — — — — — — —
T-23 Trunk Line Appearance X — — — → ———
T-42 Trunk Provisioning Service Selection — — — — — — — —
T-10 Trunk-to-Trunk Connection — — — — — — — —

T-28

Trunk-to-Trunk - Third Party
Cancellation

Fm To Fm To Fm To Fm To

————————

————————

————————

————————

————————

U-1 Uniform Call Distribution (UCD) — — — — — — — —

U-6 Uniform Call Distribution - PRI — — — — — — — —

U-3 Universal Sender — — — — — — — —

U-5 Uniform Numbering Plan - CCIS X X X X →→→→

Fm: When the call is originated from PS To: When the call terminates to PS
X: Available —: Not available
X*: Available with limitations

NEAX2400 IPX Wireless Features and Specifications
NDA-24313, Issue 1

Page 23

General Service Features

Series 7300 Series 7400

Stand Alone FCCS Stand Alone FCCS

Index Feature Name

V-1Variable Timing Parameters ————————
V-18Virtual Tie Line ——————— —

V-2Voice Call ————————

V-2D Voice Call - D

V-7 Voice Call - CCIS — — — — — — — —

V-3D Volume Control - D

W-1 WATS Access X — — — → ———

Fm: When the call is originated from PS To: When the call terminates to PS
X: Available —: Not available
X*: Available with limitations

term

————————

term

————————

Fm To Fm To Fm To Fm To

Note 1:

Note 2:
Note 3:

Note 4:

Automated Attendant: Terminating side is PS

• When the PS is Out of Zone (Out of Area or in POWER OFF state), the calling party encounters
Busy Tone, but call termination is not retried.
If the AUTOMATIC ANNOUNCEMENT - CALLED PS OUT OF ZONE [A-129] is set to the PS,
the calling party does not hear Out of Zone Announcement. The calling party hears Busy Tone, but
is not allowed to try a call termination again.

• If a PS user moves Out of Zone while talking with a subscriber of the Central Office line,
AUTOMATIC ANNOUNCEMENT - DISCONNECTED PS OUT OF ZONE [A-128] cannot be
heard by the subscriber outside. Busy Tone is heard.

• When a call activated by AUTOMATED ATTENDANT is transferred to a certain PS or a station to
which CALL FORWARDING PS INCOMING CALL IMCOMPLETE [C-155] is set and when the
transferred party is Out of Zone or in lock-out state, the calling party hears Busy Tone.

• PS is not allowed to be handed over while ringing. When the called PS is ringing with
AUTOMATED ATTENDANT in service and at the same time, its transceiver zone is switched over,
the PS stops ringing and the calling party hears Busy Tone.

This feature is not applicable using CALL TRANSFER - ALL CALLS [C-11].
If the Attendant C onsole whic h receiv ed a call fr om a Centr al Offi ce line i s rele ased while calling a PS ,

the caller changes to the Central Office li ne side.
If, in this situation, the PS user moves to a place out of Zone, the caller from the Central Office line
continues hearing Busy Tone.

Call Waiting:

• Thi s service is valid in a two-party call when call is terminated - from station-to-station, to PS, to
Central Office line, or to Tie Line call - but invalid when othe r services usin g switch hook flash are
executed to the PS or when the PS is connected to the A tte ndant Console.

• To set CALL WAITING, it is necessary that the Service Restriction Class data be assigned in the
office data assignment. Call Waiting service is provided according to each service feature
restriction class.

• There are no limitations to the number of CALL WAITING services such as the number of
simultaneous settings/the number of occurrence of answers.

Page 24

NEAX2400 IPX Wireles s Featu re s and S pe cificat io ns

NDA-24313, Issue 1

Note 5:

Note 6:

Note 7:
Note 8:
Note 9:
Note 10:
Note 11:

Note 12:

General Service Features

• This service cannot be used with the C entral Office line (DIRECT IN TERMINATION) or a call via
the Attendant Console.

While the Attendant Console is calling a PS, the services associated with Out of Zone such as CALL
FORWARDING PS INCOMING CALL INCOMPLETE [C-155], AUTOMATIC ANNOUNCEMENT ­CALLED PS OUT OF ZONE [A-129] and AUTOMATIC ANNOUNCEMENT - DISCONNECTED PS
OUT OF ZONE [A-128] are not available.
When an Attendant calls a PS, the indiv idual Att endant number can be displayed on the LCD of the PS.
However, “OPR” cannot be displayed on the LCD of the PS.

When the PS is assigned as the target station of DIRECT IN TERMINATION (DIT) [D-7]:

• When the PS is Out of Zone (Out of Zone or i n POWER OFF stat e), the call ing party hears Ring back
Tone.
Besides, if AUTOMATIC ANNOUNCEMENT - CALLED PS OUT OF ZONE [A-129] is assigned
to the PS, the calling party does not hear the Out of Zone Announcement, but hears Ringback To n e
instead.

• Even if a PS user moves Out of Zone while the talk between the corresponding PS and a subscriber
of the Central Office line is in progres s, AUTOMATIC ANNOUNCEMENT - DISCONNECTED PS
OUT OF ZONE [A-128] cannot be heard by the subscriber outside, but Busy Tone is heard instead.
The caller continues hearing Ringback Tone.

• In a call where a PS is engaged, a third-party intrusion into this line is not available upon the
activation of CALL WAITING.

• When a call through DIT is transferred to a PS or a station upon the activation of CALL
FORWARDING PS INCOMING CALL IMCOMPLETE [C-155], the calling party hears Ringback
Tone if the target PS or station is Out of Zone or in the lock-out state.

• PS is unable to be hande d over when it is ring ing. When the transceiv er zone of the PS changes over,
the called PS stops ringing, and the calling party hears Ringback Tone.

• In the FCCS network, PS must be called with Station Number.

An incoming call from the Tie Line trunk rings the same as a station call.
See STACK DIALING - STATION for the PS feature.
PS cannot be used for the Night station.
PS can activate this feature only for the Attendant Console.
Remote Access to System: Terminating side is PS:

• When the PS is Out of Zone (Out of Area or in POWER OFF state), the calling party encounters
Busy Tone, but call termination is not retried.
If the AUTOMATIC ANNOUNCEMENT - CALLED PS OUT OF ZONE [A-129] is set to the PS,
the calling party does not hear Out of Zone Announcement. The calling party hears Busy Tone, but
is not allowed to try a call termination again.

• If a PS user moves Out of Zone while talking with a subscriber of the Central Office line,
AUTOMATIC ANNOUNCEMENT - DISCONNECTED PS OUT OF ZONE [A-128] cannot be
heard by the subscriber outside. Busy Tone is heard.

• When a call activated by REMOTE ACCESS TO SY STEM is t ransferr ed to a cert ain PS or a station
to which CALL FORWARDING PS INCOMING CALL IMCOMPLETE [C-155] is set and when the
transferred party is Out of Zone or in the lock-out state, the calling party hears Busy Tone.

• PS is not allowed to be handed over while ringing. When the called PS is ringing with REMOTE
ACCESS TO SYSTEM in service and at the same time, its transceiver zone is switched over, the PS
stops ringing and the calling party hears Busy Tone.

See PRESET DIALING for the PS feature.

NEAX2400 IPX Wireless Features and Specifications
NDA-24313, Issue 1

Page 25

Note 13:

Note 14:

Note 15:

Tie Line Step Call is not available from PS.
Step call from a PS to the Attendant Console is not available.

In a FCCS network, CALL FORWARDING destination station from a PS must have a telephone
number.

PS in the Home PBX cannot pick up the PS ringing in the Visit PBX over FCCS network.

Page 26

NEAX2400 IPX Wireles s Featu re s and S pe cificat io ns

NDA-24313, Issue 1

Radio Channel Changeover R-50

R-50 Radio Channel Changeover

General Description

This service superv ises an d contr ols (chang eove r) the channel automatically to avoid interference an d to maint a in
speech quality.

Operating Procedure

No manual operation is required.

Service Conditions

1. There is no int erru pt ion i n speech when this serv ic e is activated .

2. The new channel is assigned to the party which has moved into the service area.

3. When no idle channel is available, the call is continued on the same channel until the communication
becomes unavailable, then AUTOMATIC RELEASE - OUT OF CELL CALLS is activated.

NEAX2400 IPX Wireless Features and Specifications
NDA-24313, Issue 1

Page 27

S-130 Speech Scrambl ing

S-130 Speech Scrambling

General Description

This service protects calls from being tapped.

Operating Procedure

No manual operation is required.

Service Conditions

1. This service is activated for every originating call from the D

term

D

PS. For every call, the encryption assignment message is sent from the D

transceiver.

2. ENCRYPTION is automatically activated throughout a call. Cancelling encryption during a call is not
possible.

term

PS and for every terminating call to the

term

PS to the zone

Page 28

NEAX2400 IPX Wireles s Featu re s and S pe cificat io ns

NDA-24313, Issue 1

Out Of Cell Indication O-38

O-38 Out Of Cell Indication

General Description

When the D
rate exceeds the threshold, this service notifies the user with a warning tone and the LCD display.

Operating Procedure

No manual operation is required.

Service Conditions

1. If the D

2. When the D

3. When the electric field strength becomes so weak that communication cannot be continued or when the

term

PS series user moves out of the service area, the electric field strength becomes weak or the Error

term

PS user turns the power on when he/she is out of the service area or when the user moves out
of the service area while idle, “antenna pict” display goes off and the LCD displays “NO SVC” or “No
Service” in the upper section.

term

PS user moves out of the servi ce area while engaged in a call, “antenna pict” display goes
off and the LCD display s “NO SVC” or “No Service” in the upper sec tion after th e user receives a war ning
tone.

Error rate exceeds th e threshold, A U TOMATIC RELEASE - OUT OF CELL CALLS is activated.

NEAX2400 IPX Wireless Features and Specifications
NDA-24313, Issue 1

Page 29

A-131 Automatic Rele ase - Out Of Ce l l Call s

A-131 Automatic Release - Out Of Cell Calls

General Description

When the D
channels o f ZT s are busy a n d the com munication becomes unavaila b le , t he call will be disconnected automatically
and Reorder Tone or Out of Area Announcement will be sent to the opposite end.

Operating Procedure

No manual operation is required. When the number of the party engaged in the call is displayed, it will be cleared.

Service Conditions

1. When the electric field strength becomes weak due to the D

2. When the electric field strength becomes so weak that communication is no longer available or when Error

term

PS series user engaged in a call moves out of the service area or enters radio zone where all the

term

PS user moving out of the service area or
entering a rad io zone where all th e channe ls of ZTs ar e busy, or when the Error ra te exceed s the thr eshold ,
OUT OF CELL INDICATION is activated.

rate exceeds the threshold, the call will be disconnected automatically.

Page 30

NEAX2400 IPX Wireles s Featu re s and S pe cificat io ns

NDA-24313, Issue 1

PS Authentication P-61

P-61 PS Authentication

General Description

This service confirms the identity of the D

Operating Procedure

No manual operation is required. The D
possesses the key information unique to each D

term

the D

PS.

Service Conditions

term

PS to avoid an unauthorized terminal from accessing the system.

term

PS identity is confirmed automatically by checking if the D

term

PS. This ch eck is perfo rmed betwe e n t he N E AX2400 IPX and

term

PS

This service is activated in the following circumstances

1. When the D

2. When a call terminates to the D

term

PS user originates a call.

term

PS.

3. When HANDOVER service is activated.

term

4. When the D

PS registers its location to the system (when idle).

NEAX2400 IPX Wireless Features and Specifications
NDA-24313, Issue 1

Page 31

P-62 PS Location Registration

P-62 PS Location Registration

General Description

This service allows the NEAX2400 IPX to supervise the loc ation of each D
registration request, to allow call termination.

Operating Procedure

No manual operation is required.

Service Conditions

1. This servic e is activated every ti me t he D
areas can be ins talle d i n t he P C N of the NEAX2400 IPX.

2. A maximum of 192 zone transceivers can be installed in a single st ac k.

3. PS AUTHEN T ICATION i s act iv at ed ev ery time the D

4. In a FCCS network, the calling area cannot be assigned over multiple nodes.

term

PS enters a different calling area. A maximum of 32 calling

term

term

PS series upon receiving the location

PS requests location registration.

Page 32

NEAX2400 IPX Wireles s Featu re s and S pe cificat io ns

NDA-24313, Issue 1

Overlap Dialing O-39

O-39 Overlap Dialing

General Description

This service allows the D

Operating Procedure

To originate a call

1. Press the SEND or L1/L2 key; receive Dial Tone.

2. Dial the desired number. The dialed numbers are displayed on the LCD.

Service Conditions

1. A maximum 24 digits (numbers 0 to 9, #, and *) can be dialed. (A maximum of 12 digits can be displayed
on the LCD.)

2. The D

3. The prepause timer after receiving Dial Tone is te n seconds; a nd if no number is di aled within thi s period ,

4. If the interdigit t imer e xpires whi le the user is dia ling the n umber, the num bers dialed before the tim er wi ll

5. For every call origination, PS AUTHENTICATION is activated.

6. The D

term

the user receives Reorder Tone.

be sent out.

term

term

PS series user to receive a Dial Tone and to dial t he d esired number to originate a call .

PS user can dial the number before hearing Dial Tone.

PS-to-D

term

PS calls cannot be recorded for the SMDR.

NEAX2400 IPX Wireless Features and Specifications
NDA-24313, Issue 1

Page 33

P-63 Preset Dialing

P-63 Preset Dialing

General Description

This service allows the D

Operating Procedure

To originate a call

1. Dial the desired number. The number is stored and displayed on the LCD.

2. After confirming the numbers, press the SEND or L1 key. The numbers are displayed on the LCD
throughout the conversation.

Service Conditions

1. A maximum of 24 digits (numbers 0 to 9, #, *, and pause) can be stored. (A maximum of 12 digits can be
displayed on the LCD. When more than 12 digits are dialed, the digits move from right to left, displayi ng
only the most recently dialed digits.)

2. If a wrong number is dialed, press the CLR or CLEAR key. The number just dialed will be erased. If the
CLR or CLEAR key is pressed for more than two seconds, the numbers will be erased suc cessivel y. Also,
if no number is entered for 20 seconds, the service is cleared, and the D
(stand by status).

3. If the user dials a number after pressing the SEND or L1/L2 key, it will be recognized as a PB signal
sending.

4. PS AUTHENTICATION is activated for every call origination.

term

PS series user to confirm the numbers to be dialed before originating calls.

term

PS returns to the idle state

Page 34

NEAX2400 IPX Wireles s Featu re s and S pe cificat io ns

NDA-24313, Issue 1

Individual PS Calling I-39

I-39 Individual PS Calling

General Description

This service allows the calling party to call the individual D

Operating Procedure

1. Dial the unique number assigned to each D
number display is available, the lower 12 digits of the number ar e displayed on th e LCD of the called D
PS. (The arrow is displayed to show that the upper digits are not displayed.)

2. There are two answering options:

a.) Any-key answering mode

term

The called D

PS user presses any one of the keys (numbers 0 to 9, #, *, or function keys) to

answer.

b.) Automatic answering mode

The called D

term

PS is connected automatically without ringing.

Service Conditions

1. The D

2. If the D

3. When all the speech channels of the zone transceiver in the Calling Area are busy, either

4. PS AUTHENTICATION is activated for every call termination.

5. The answering options, the any-key answering mode and the automatic answering mode can be selected

term

PS will be called in the cal ling area where its loc ation had been registered.

term

PS cannot be called as whe n the D

be provided to the calling p arty. (The DAT pa ckage i s re quire d for t he c aller and cal led nod e.) I f the c alle d

term

D

PS is out of the service area, OUT OF CELL INDICATION is activated.

ANNOUNCEMENT - PS OUT OF CELL or CALL FORWARDING - PS OUT OF CELL is activated, if

term

allowed in the D

PS service feature class. If not allowed in the service feature class, the D

receives Reorder Tone.

by the D

term

PS user using the FNC key.

term

PS series.

term

PS; the designated D

term

PS user is out of the serv ice area, an a nnouncemen t can

term

PS will be called. If the calling

term

term

PS user

NEAX2400 IPX Wireless Features and Specifications
NDA-24313, Issue 1

Page 35

H-23 Handover

H-23 Handover

General Description

When speech transmission quality becomes inferior, the D
another radio channel, making the PBX hand the call over to another zone transceiver to maintain speech quality.

Operating Procedure

No manual operation is required. The D

term

PS series automatically sends HANDOVER request to the PBX.

Service Conditions

1. This service is activ at ed w h en the D

2. The communication may be interrupted when the PBX hands the call over. The interruption is usually
within a second, to a maximum of ten seconds.

3. This service is also available when a D
inferior transmission quality. In this case, the D
electric field, and if the radio zone is found, HANDOVER is activated and the conversation is continued
in that zone. If the re is no idl e channel i n th e new radio zone, th e conversation is continued in the current
zone until the communication becomes unavailable, and AUTOMATIC RELEASE - OUT OF CELL
CALLS is activated.

4. PS AUTHEN T ICATION i s act i v ated ev ery time this serv ice is activated.

5. In a FCCS network, inter-n ode HANDOVER is available wit hin the identical PCN.

term

PS is engaged in communication.

term

PS user moves to the far end of the radio zone and encounters

term

PS re-originates a call automatically and seizes

term

PS searches for the radio zone with the stronger

Page 36

NEAX2400 IPX Wireles s Featu re s and S pe cificat io ns

NDA-24313, Issue 1

DTMF Signal Sender D-154

D-154 DTMF Signal Sender

General Description

This serv ice allo ws t he D
system, etc.) while engaged in communication.

Operating Procedure

To send the DTMF signal

1. Press a key while engaged in communicat ion. The PBX automati call y sends the c orres ponding sign al tone
to the called party.

Service Conditions

1. When the DTM F sign al i s se n t , there may be an interr u p tio n in communication.

2. The DTMF signal tone varies between 64 ms to 72 ms.

3. When this service is activated, the number pressed is displayed on the LCD (clearing the called party
number previously displayed). The LCD display is cleared after 20 seconds, but the called party number
will not be displayed again.

term

PS series user to send the PB signal (tone) to the called party (terminal, voice mail

NEAX2400 IPX Wireless Features and Specifications
NDA-24313, Issue 1

Page 37

C-156 Consultation Hold

C-156 Consultation Hold

General Description

This service allows the D

term

PS user to place a call on hold. Only that D

Operating Procedure

To place a c a ll on hold

1. While engaged in a call, p ress the TRF or F 2 key; recei ve Specia l Dial Tone. The calle d numbe r displ ayed
on the LCD while engaged in a call will go out when the TRF or F2 key is pressed. The called party hears
music via the external source.

2. To retrieve the call, press the TRF or F2 key again. The called party number will not be displayed on the
LCD again.

Service Conditions

1. When the D
receives Reorder Tone and the connection is released. If t he D
before pressing the END key while holding the call, the user is called back.

term

PS user presses the END key while hold ing the call without diali ng any key, the held party

term

PS user can retrieve the held call.

term

PS user has dialed one or more keys

Page 38

NEAX2400 IPX Wireles s Featu re s and S pe cificat io ns

NDA-24313, Issue 1

Flexible PS Numbering F-34

F-34 Flexible PS Numbering

General Description

Each D

Operating Procedure

No manual operation is required. The data is entered via the maintenance administration terminal.

Service Conditions

term

PS series is assigned an unique number.

1. A maximum of nine digits can be assigned for a D
numbers must be assigned in uniform number of digits.

term

PS number, including # and *. The D

term

PS

NEAX2400 IPX Wireless Features and Specifications
NDA-24313, Issue 1

Page 39

P-64 PS Service Class

P-64 PS Service Class
P-65 PS Restriction Class

General Description

This service permits all the D
system use desired.

Operating Procedure

No manual operation is required.

Service Conditions

1. The route service class is assigned to determine the accessibility to the following service features.

ANNOUNCEMENT - DON'T ANSWER
ANNOUNCEMENT - PS OUT OF CELL
CALL FORWARDING - DON'T ANSWER
CALL FORWARDING - PS OUT OF CELL
CENTREX COMPATIBILITY

2. Each D
D

3. Each D
placing CO outgoing calls, etc. There are 15 classes and these classes are assigned in the system
paramete rs (traveling class mark). Refer to D IRECT OUT WARD DIAL ING RESTRI CTION (3-9 ) for
more details.

term

term

PS is assigned a service feature class to determine which of the following service features the

PS will be permitted to activate.

CALL TRA NSFER
CALL WAIT ING - TERM IN A T IN G
CENTREX COMPATIBILITY
ANNOUNCEMENT SERVICE
ANNOUNCEMENT - DON'T ANSWER/CALL FORWARDING - DON'T ANSWER
ANNOUNCEMENT - PS OUT OF CELL/CALL FORWARDING - PS OUT OF CELL
TRUNK LINE APPEARANCE

a.) ANNOUNCEMENT SERVICE /ANNOUNCEMENT - DON'T ANSWER/CALL

FORWARDING - DON'T ANSWER/ANNOUNCEMENT - PS OUT OF CELL/
ANNOUNCEMENT - DON'T ANSWER - When the restricted D
access code, the user receives Reorder Tone. If the CALL FORWARDING - INTERCEPT/
ANNOUNCEMENT service is set, the announcement notifying the user that an invalid number
was reached will be sent.

b.) CALL TRANSFER - When a restricted D

FLASH key), the operation will be ignored.

c.) CALL WAITING - TERMINATING - When Call Waiting is attempted to the restricted D

which is busy, the calling party receives Reorder Tone.
d.) CENTREX COMPATIBILITY - The switch hook fla s h operation will b e invalid.
e.) TRUNK LINE APPEARANCE - When the restricted D

via the TRUNK LINE APPEARANCE service, the user receives Reorder Tone.

term

PS is assigned a service restriction class linking to that of the PBX to restrict the user from

term

PS serie s to be assi gned a class of servic e in acco rdanc e with the de gree of the

term

PS user dials the service

term

PS attempts Call Transfer (pressing of the TRF/

term

PS user attem pts to originate a call

term

PS

Page 40

NEAX2400 IPX Wireles s Featu re s and S pe cificat io ns

NDA-24313, Issue 1

PS-to-Station Calling P-66

P-66 PS-to-Station Calling

General Description

This service allows the D

Operating Procedure

To place a call using OVERLAP DIALING

1. Press the SEND or L1 key; receive Dial Tone.

2. Dial the desired number; receive Ringback To ne.

To place a call using PRESET DIALING

1. Dial the desired number, then press the SEND L1 key; receive Ringback Tone.

Service Conditions

1. The dialed digits are sent out in the following timing:
a.) when the NEAX2400 IPX recognizes the last digit according to the numbering plan

b.) if the NEAX2400 IPX cannot recognize the last digit, ten seconds after the last digit is dialed

(inter-dig it timer time-out).

term

PS series user to place a call to a PBX station, and vice versa.

NEAX2400 IPX Wireless Features and Specifications
NDA-24313, Issue 1

Page 41

S-131 Stack Dialing - Station

S-131 Stack Dialing - Station

General Description

This service allows the D
pressing the REDIAL/PAUSE or F3 key.

Operating Procedure

To store the number

1. Using either OVERLAP DIALING or PRESET DIALING, dial the desired number. The number dialed

is stored automatically.

To redial the stored number using OVERLAP DIALING

1. Press the SEND or L1 key, then REDIAL/PAUSE or F3 key; the newest stored number is displayed on

the LCD digit by digit, moving from right to left. The displayed number is dialed automatically.

To redial the stored number using PRESET DIALING

1. Press the REDIAL/PAUSE or F3 key; the stored number is displayed on the LCD digit by digit, moving

from right to left. By pressing the REDIAL/PAUSE or F3 key repeatedly, the second and the third
numbers will be displayed successively.

2. When the desired number is displayed, press the SEND or L1 key. The number is dialed automatically.

term

PS series user to store the last five numbers dialed and to redial the numbers by

Service Conditions

1. A maximum of 40 digits (the numbers 0 to 9, #, *, and the function keys) can be stored.

2. The numbers are stored in the memory in the order they are dialed. If the number identical to the one in

the memory is dialed, that number is recognized as the newest number, and the one already stored will be
erased. (Regardless of the number of times the same number is dialed, it is stored only once.)

Page 42

NEAX2400 IPX Wireles s Featu re s and S pe cificat io ns

NDA-24313, Issue 1

Speed Cal l ing - St ati o n S-132

S-132 Speed Calling - Stat io n

General Description

This service allows the D
codes.

Operating Procedure

The Speed Calling data is set via the user definable data assignment. For detailed operation, refer to the D
User Guide.

Service Conditions

1. Each abbreviated call code can store a maximum of 40 digits (the numbers 0 to 9, #, *, and the function

keys).

2. A maximum of 20 call codes can be assigned.

3. If PRESET DIALING, when a wrong number is dialed, it can be cleared by the CLR or CLEAR key.

term

PS series user to dial certain frequently called numbers using 2-digit abbreviated call

term

PS

NEAX2400 IPX Wireless Features and Specifications
NDA-24313, Issue 1

Page 43

A-128 Automatic Announcement - Disconnected PS Out Of Zone

A-128 Automatic Announcement - Disconnected PS

Out Of Zone

General Description

When a talking D
call disconnected, the counterpart hears the announcement that the talks are disconnected due to the talking party
moving Out of Zone. This also can apply when the power of either D

Operating Procedure

No manual operation is required.

Service Conditions

1. This service is valid only in a two-party call. This service cannot be used when a call is placed on hold or

conference calling participated in by three-party or more is in progress.

2. DAT (Digital Announcement Trunk) circuit card can be used as an announcement trunk.

3. AUTOMATIC ANNOUNCMENT - D ISCONNECTED PS OUT OF ZONE is not applied to the cases

where calls are in progress via a COT line or Attendant Console. A C.O. line subscriber hears Reorder
Tone and a caller via the Attendant Console encounters Busy Tone.

4. In a FCCS network, every node must have one or more announcement trunk(s).

term

PS series user moves Out of Zone, that is, the Wireless service area, to have the progressing

term

PS is OFF.

Page 44

NEAX2400 IPX Wireles s Featu re s and S pe cificat io ns

NDA-24313, Issue 1

Automatic Announcement - Called PS Out of Zone A-129

A-129 Automatic Announcement - Called PS

Out of Zone

C-155 Call Forwardi ng PS Incoming Call Incomplete

General Description

When a call cannot be termi n at ed due to the called D
system automatic ally answe rs the call a nd prov ides a n announce ment t o notify the c alling party tha t th e called D
PS is Out of Zone or if the CALL FORWARDING PS INCOMING CALL INCOMPLETE is set to a given
destination, the aborted call can be transferred to the pre programmed station or D

Operating Procedure

No manual operation is required.

Service Conditions

term

PS series which is Out of ZT or whose power is OFF, the

term

PS.

term

1. CALL FORWARDING PS INCOMING CALL INCOMPLETE can be pr ogrammed and c ancelled b y the

2. In the case where the D

3. One system is given one kind of recorded message for AUTOMATIC ANNOUNCEMENT - CALLED

4. On the condition that both AUTOMATIC ANNOUNCEMENT - CALLED PS OUT OF ZONE and

5. If an incoming call terminated at the very moment when a D

6. If the another transfer service is set to the target destination party of CALL FORWARDING PS

7. When a call is transferred to another D

8. AUTOMATIC ANNOUNC EMENT - CALLED PS OUT OF ZONE does not allow the incoming call

term

D

PS with pressing Access Code + transferred telephone number.

term

PS is Out of Zone, or its power is OFF, and the call is an incoming call from
the Central Office directly or the Central Office call via the Attendant Console, the caller does not hear
AUTOMATIC ANNOUNCEMENT - CALLED PS OUT OF ZONE, and hears the following tones.

• DIT: Ringback Tone is heard

• REMOTE ACCESS TO SYSTEM: Busy Tone is heard

• AUTOMATED ATTENDANT: Busy Tone is heard

• ATTENDANT CONSOLE: Busy Tone is heard

• ISDN - DID ADDRE SSI N G : Announcement of ISDN (PSTN) is heard.

PS OUT OF ZONE.

CALL FORWARDING PS INCOMING CALL INCOMPLETE are assigned to a D
given to CALL FORWARDING PS INCOMING CALL INCOMPLETE.

FORWARDING PS INCOMING CALL INCOMPLETE with a Pre-Set Dialing (befor e OFF-HOOK), the
procedure so far becomes invalid.

INCOMING CALL INCOMPLETE, the call is transferred to the last end party.

term

PS activated by CALL FORWARDING PS INCOMING
CALL INCOMPLETE and when the call termination is not completed, the call can be transferred to
another destination party if the CALL FORWARDING PS INCOMING CALL INCOMPLETE is set. If
the AUTOMATIC ANNOUNCEMENT - CALLED PS OUT OF ZONE is assigned, the caller hears the
announcement. When both CALL FORWARDING PS INCOMING CALL INCOMPLETE and
AUTOMATIC ANNOUNCEMENT - CALLED PS OUT OF ZONE are no t progr ammed, the calle r he ars
Busy Tone.

from outside to be connected to announcement trunk. The calling party hears Ringback Tone.

Note

term

PS, priority is

term

PS series user is setting CALL

NEAX2400 IPX Wireless Features and Specifications
NDA-24313, Issue 1

Page 45

C-155 Call Forwarding PS Incoming Call Incomplete

Service Cond iti o ns (co nt ’ d)

term

9. The incoming incomplete call to a D

PS can be transferred to other D
Consoles, Central Office and TIE lines when CALL FORWARDING PS INCOMING CALL
INCOMPLETE is in service.

10. The timer value of incoming incomplete call is approximately eight seconds, time duration until the
system recognizes that the D

term

PS is Out of Zone from an incoming call attempt to the D

11. CALL FORWARDING PS INCOMING CALL INCOMPLETE is not activated in the case of the
incoming call from ISDN and the incoming call via the Attendant Console. The caller encounters
AUTOMATIC ANNOUNCEMENT - CALLED PS OUT OF ZONE or Busy Tone.

12. When a forwarded stati on for CALL F ORWARDING PS INCOMING CALL I NCOMPLETE se ts CALL
FORWARDING - ALL CALLS to the announcement, CALL FORWARDING PS INCOMING CALL
INCOMPLETE is not activated but the caller hears Busy Tone.

13. In a FCCS network, every node must have one or more Announcement Trunk.

14. When incoming call com es fro m ISDN net w o rk , and t h e tim er (T 310) of the network side is expired, the
caller may hear the Announcement from network side.

15. In a FCCS network, CALL FORWARDING destination station must have a telephone number.

Note:

CALL FORWARDING PS INCOMING CALL INCOMPLETE is cancelled by system initialization if the
data is not saved on the Hard Disk.

term

PS’s, stations, Attendant

term

PS.

Page 46

NEAX2400 IPX Wireles s Featu re s and S pe cificat io ns

NDA-24313, Issue 1

term

D

PSII Two Line Operation D-155

D-155 D

General Description

This feature allows for the appearance of two lines on the line (L1 and L2) keys of the PS.

Operating Procedure

No manual operation is required.

Service Conditions

1. This feature is available for Series 7300 or later software.

2. Two kinds of lines can appear on the PS: My Line and Sub Line. These lines are associated with the
telephone numbers assigned to the port on the interface circuit.

L1 key: My Line
L2 k e y: Su b L in e

3. When a PS bec o mes Out of Zon e st at e wh i le te rmi n at i n g to Sub Line, the call is disc o n ne ct ed by rele a se
timer about one minute after.

4. When a PS user places a call on hold and presses the END key, the line lamp on the PS goes OFF. The PS
is recalled when the recall timer expires.

5. Voice Mail Indication (VMI) is not available for Sub Line.

6. When a PS is conn ected to a P S, Dual H o ld is not av ai l ab l e.

7. Blind Transfer to Sub Line is not available.

8. When one Line is connected, Blind Transfer to the other line is not available.

9. When transferring a call from a PS, the PS cannot place the third party on Hold.
The PS cannot activate Call Hold while connected with the station holding another call.

10. A PS cannot activate Call Hold when:

a.) Call Waiting is set to the PS
b.) the PS sets Call Waiting
c.) Call W ai t ing is set to th e station connected w ith t he PS

11. Call Waiting cannot be activated while the called PS is placed on Hold.

PSII Two Line Operation

term

NEAX2400 IPX Wireless Features and Specifications
NDA-24313, Issue 1

Page 47

N-43 Name Display - Intra-Node Call

N-43 Name Display - Intra-Node Call

General Description

This feature allows a PS to indicate user information corresponding to the calling Physical Station Number while
engaged in a station-to-station call.

Operating Procedure

• When originating a station-to-station call:

LCD display of the calling station:

H. TARO
DIR SPD LNR

LCD display of the called station:

H. TARO
DIR SPD LNR

• When a station call has been transferred to another station by Call For warding - All Calls/Busy Line/Don ’t

Answer/PS - Incoming Incompl ete:
LCD display of the calling station:

CF: H. TARO
DIR SPD LNR

LCD display of the called station:

CF: M. TARO
DIR SPD LNR

Service Conditions

1. This feature is available for Series 7300 or later software.

2. User information corresponding to the Physical Station Number that can be displayed on the LCD is a
maximum of 16 digits.

3. User information is displayed on the LCD, indented to the left. The information may consist of English
alphabets, numeric characters, and most keyboard symbols.

4. When user information is 12 digits or more, the first or last part of information can be displayed by key
operation (Refer to the User Gu ide for the PS).

5. This service and NAME DISPLAY by Open Application Interface cannot be activated concurrently.

term

6. This service an d NAME DISP L A Y service f or D

7. Eight-digit display or 16-digit display is selectable by System Data, but cannot be used concurrently.

8. If the PS station has no name programmed for NAME DISPLAY - INTRA-NODE CALL service, the
Physical Station Number is displayed in the name field.

9. NAME DISPLAY - INTRA-NODE CALL is available for Station-to-Station Connection, Call
Forwarding - All Calls/Busy Line/Don’t Answer/PS - Incoming Incomplete, Call Waiting, and Call
Transfer.

s can be activated concurrently.

Page 48

NEAX2400 IPX Wireles s Featu re s and S pe cificat io ns

NDA-24313, Issue 1

Name Display - Intra-Node Call - CCIS N-44

N-44 Name Display - Intra-Node Call - CCIS

General Description

Between CCIS nodes this feature allows the calling or called party information to be displayed on the LCD of a PS.

Operating Procedure

• When originating a call:

LCD display of the calling station:

H. TARO
DIR SPD LNR

LCD display of the called station:

H. TARO
DIR SPD LNR

• When a call has been transferred to a nother statio n by CALL FORWARDING - ALL CALLS/BUSY LINE/

DON’T ANSWER/PS - INCOMING INCOMPLETE:
LCD display of the calling station:

H. TARO
DIR SPD LNR

LCD display of the called station:

CF: M. TARO
DIR SPD LNR

Service Conditions

1. This feature is available for Series 7300 or later software.

2. User information corresponding to the Physical Station Number that can be displayed on the LCD is a
maximum of 16 digits.

3. User information is displayed on the LCD, indented to t he left. The infor mation ma y consist of upp er c ase
letters, numeric characters, and most keyboard symbols.

4. When user information is 12 digits or more, the first or last part of information can be displayed by key
operation (Refer to the User Guide of PS).

5. This service and NAME DISPLAY by Open Application Interface cannot be activated concurrently.

term

6. This service an d NAME DISP L A Y service f or D

7. Eight-digit display or 16-digit display is selectable by System Data, but cannot be used concurrently.

8. If the PS station has no name programmed for NAME DISPLAY - INTRA-NODE CALL - CCIS service,
“Office Code + Physical Station Number” is displayed in the name field.

9. NAME DISPLAY - INTRA-NODE CALL - CCIS is available for Tie Line Connection, Call Forwarding

- All Calls/Busy Line/Don’t Answer/PS - Incoming Incomplete, Call Waiting, and Call Transfer.

s can be activated concurrently.

NEAX2400 IPX Wireless Features and Specifications
NDA-24313, Issue 1

Page 49

N-45 Number Sharing

N-45 Number Sharing

General Description

This feature allows the D

term

user to use a PS as a Sub Station. In this feature, the D

Station and Sub Station, respectively. The main functions of this feature are as follows:

1. Call Forwarding - All Calls to PS - When the D

term

(Main Station) us er presse s the f eature ke y or dials the
access cod e, Call Forward i n g - Al l Calls to PS (Sub St at ion ) is set or cancelled . T his function c a n al s o be
set or cancelled b y dialing th e access code from the PS (Sub Station).

2. D

term

- Telephone Number Display - Even if a call is connected to the PS (Sub Station), the telephone

number of the D

term

(Main Station) is displayed on the other party’s LCD.

3. Billing Information - Even if a c all is o rigina ted fro m the PS (S ub Station) , billi ng inf ormati on is re corded
as a call origination from the D

term

(Main station).

4. Voice Mail Indication - Even if a call is transferred from the PS (Sub St a t i on) t o the Vo ice Mail Sy st em ,
the voice mail is recorded on the mail box of the D
Waiting Indication on both the D

term

(Main Station) and PS (Sub Station).

term

(Main Station). The system controls Message

Operating Procedure

To set from the D

1. While in idle state, press the feature key for this feature. The PS Transfer lamp lights on the D
Station).

2. Al l th e call s t o the D

To cancel from the D

1. While the Sub Station Transfer lamp lights, press the feature key for this feature. The PS Transfer lamp
goes off on the D

2. This feature is cancelled.

To set from the PS

1. While in idle state , dial the access code for t his feature and r eceive Se rvice Set Tone. T he PS T ransfer
lamp lights on the D

2. Al l th e call s t o the D

To cancel from the PS

1. While this feature is set, dial the cancel code for this feature and receive Service Set Tone. The PS Transfer
lamp goes off on the D

2. This feature is cancelled.

term

term

term

(Main Station) are forwarded to the PS (Sub Station).

term

(Main Station).

term

(Main Station).

term

are forwarded to the PS (Sub Station).

term

(Main Station).

term

and PS are referred as Main

term

(Main

Service Conditions

1. This feature is available for Series 7300 or later software.

2. A telephone number must be assigned to both Main and Sub Stations.

3. The PS cannot be assigned as Main Station.

4. Any com b ination of Main Statio n and Su b S t a tion is available in a FCCS network.

5. The access code for an outgoing call cannot be assigned as a telephone number of the Sub Station.

6. Dialing the access code for this feature is available only for Main Station and Sub Station. Any other
station or trunk cannot s et this feature.

term

7. The D

user can set this feature using any line on the D

a sub line, this feature is set to My Line.

8. The “PS Transfer” key is available only when the D

Page 50

term

. Even if the D

term

is in idle state.

term

user sets this featu re using

NEAX2400 IPX Wireles s Featu re s and S pe cificat io ns

NDA-24313, Issue 1

Number Sharing N-45

Service Cond iti o ns (co nt ’ d)

9. When this feature is set whi le a call is terminating to Main Stat ion, the ca ll is not transferred to Sub Station .
In this case, this feature is available from the next call.

10. Message Waiting Lamp control by MEASSAGE REMINDER or CMWL command is applied only to the
called/designated station.

11. Even if this feature is set, recall to Main Station is not forwarded to Sub Station.

12. Forwarding operati on of t h is feature is not counted in Multiple Call Forwarding features.

13. When a call is originated from Sub Station to OAI or MFC, the Sub Station number is sent.

Interactions

1. This feature takes precedence over the Call Forwarding, Do Not Disturb and Station Hunting features set
to Main Station.

2. When this feature is set, all the calls are forwarde d to Sub Station even if CALL BLOCK [C-150] is set to
Main Station.

3. Off-Hook Line Number Display feature of the PS is independent of this feature.

term

4. MW indication for Sub Station is available for My Line of the D

5. When a Main Station is in a Station Hunting group, this feature can be activated only if the Main Station
is the pilo t stat ion.

- PSII only.

NEAX2400 IPX Wireless Features and Specifications
NDA-24313, Issue 1

Page 51

V-24 Voice Mail Indication (VMI)

V-24 Voice Mail Indication (VMI)

General Description

This feature allows the system to notify a PS that a voice mail has been received.

Operating Procedure

No manual operation is required.

Service Conditions

1. This feature is available for Series 7300 or later software.

2. When a voice mail is received while the PS user is in conversation, the system notifies the PS after the
conversion ends.

3. When voice mails for multiple PS users are simultaneously received, each node can notify a maximum of
240 PSs. For the other PSs, notification is given at the time of PS Location Registration or end of call.

4. When a notification is given at the time of PS Location Registration or end of call, further notifications to
the same PS are not given unless the PS user accesses the voice mail system.

5. When a notification could not be terminated to a PS because of PS Out of Zone etc., the system notifies
again aft er four m i nutes.

6. This service and Open Application Interface (OAI) cannot be activated concurrently.

Page 52

NEAX2400 IPX Wireles s Featu re s and S pe cificat io ns

NDA-24313, Issue 1

Wireless Analog Adjunct Connection W-8

W-8 Wireless Analog Adjunct Connection

General Description

This feature allows the existing PBX (no wireless function) to operate a PS as well as a station in the office. Each
PS is connect ed with the ded icated CO T in the Built- in Wireles s system . When a call is originated from t he PS, it
terminates to the LC in the existing PBX via the corresponding COT and is handled by the existing PBX.

Existing PBX (no wireless functio n) Built-in Wireless Sys tem

C.O.
Line

TIE

Line

Station

COT

ODT

LC

STN-A

STN-B

LC

LC

COT

COT

CSINT

PS-A

PS-B

Operating Procedure

No manual operation is required.

Service Conditions

1. Only DTMF signals can be sent to the existing PBX.

2. Only one COT circuit card must be assigned for one PS.

3. When an incom ing ca ll terminat es from the exis ting PBX t o a PS via the LC → CO T, if th e te rm in a tin g
PS is busy or out of zone, call termination is perfo rm ed ag a in.

Note:

The calling par ty hears Ringback Tone without conditi on. While Ringback T one is sent, the Built- in Wireless
System attempts the call termination to the called PS periodically and ring the PS when the PS becomes
available.

4. The distinctive ringing service is not provided when a call terminates to the PS.

5. When the Speed Calling - System/Station service is activated using Overlap Dialing including the access
code, the number dialed may not be stored for redialing.

6. Whether or not Call Forwarding services (Call Forwarding - All Calls/Busy Line/Don’t Answer) by the
access code are available depends on the system data of the existing PBX. The Call Forwarding service
set by access code is activated only when the call terminates to the corresponding LC in the existing PBX.

7. The CALL FORWARDING PS INCOMING CALL INCOMPLETE [C-155] service cannot be set to a
PS.

8. When a call terminates from the existing PBX to the PS out of zone, the AUTOMATIC
ANNOUNCEMENT - CALLED PS OUT OF ZONE [A-129] service cannot be activated. (The calling
party continues to hear Ringback Tone.)

9. When the PS engaged in a connection via the existing PBX moves Out of Zone, the AUTOMATIC
ANNOUNCEMNET - DISCONNECTED PS OUT OF ZONE [A-128] service is not provided. (The
calling party hears Reorder Tone.)

10. This feature is not available in the FCCS network.

ZT

NEAX2400 IPX Wireless Features and Specifications
NDA-24313, Issue 1

Page 53

W-8 Wireless Analog Adjunct Connection

Service Cond iti o ns (co nt ’ d)

11. When a call terminates to the PS using this feature, the calling number is not displayed on the PS.

12. The following PBX services are available for PS’s using this feature:

• C.O. call origination

• C.O. call termination

• Intra-office services

• Common, the other services

•ISDN service

• Net w o rk s ervice

• Call charging management service

• Maintenance administration service

Page 54

NEAX2400 IPX Wireles s Featu re s and S pe cificat io ns

NDA-24313, Issue 1

ISDN Roaming I-41

I-41 ISDN Roaming

General Description

This feature allows PS to move to another PBX which has a different SYS-ID via Q.931a connection. The PBX
which PS can roam from/to is assigned Network Number (NWN). Network Number must be assigned as a unique
number for each network.

Operating Procedure

1. PS moves t o an o t h er PB X w h ich h as a different SYS-I D.

2. PS registers its location automatically to the Home PBX at the Visitor PBX via Q.931a connection.

3. PS can originate a call from the Visitor P BX.

4. A call terminating to the PS is transferred from th e Home PBX to the Visi tor PBX via Q.931a connection.

Service Conditions

1. This feature is available for the Series 7300 software.

2. This feature is available between the PBXs which are connected via Q.931a.

3. PS in the Visitor PBX cannot move to another PBX via FCCS connection.

4. SMDR outputs the PS number instead of the account code when the PS is in the Visitor PBX.

5. In the Visitor PBX, PS cannot use supplementary services which need service access code. However,
TRANSFER, CALL HOLD and some ANNOUNCEMENT SERVICE are available.

6. If there is a TS between the Home PBX and Visitor PBX, the TS must also have the roaming feature.

7. CF - All Calls/Busy Line/PS Incoming Call Incomplete

a.) CF - All Calls - If PS assigns CF - All Calls at the Home PBX, all the terminating calls are

transferred. PS can also originate a call from the Visitor PBX.

b.) CF - Busy Line - If PS is busy in the Visitor PBX, the terminating call is transferred from the

Home PBX.

c.) CF - PS Incoming Call Incomplete - If call termination to PS is incomplete in the Visitor PBX,

the incoming call is transferred from the Home PBX.

8. In the Visitor PBX pseudo PS Physical S tation Number (VIS ITOR PS PHYSICAL STATION NUMBER)
must be assigned by S y s tem Data. In addition, telephone number for visitor PS Physical Station Number
must be assigned.

Note:

Visitor PS Physical Station Number must be the number which is not used in the Visitor PBX for the other
Physical Station Number.

9. The maximum number of PS’s includes the number of visitor PS Physical Station Numbers.

10. Roaming PS cannot use Two-Line feature.

11. Roaming PS cannot use Voice Mail Indication (VMI) feature.

12. Roaming PS cannot use OAI features.

NEAX2400 IPX Wireless Features and Specifications
NDA-24313, Issue 1

Page 55

I-41 ISDN Roaming

Service Cond iti o ns (cont ’d)

13. A PS can move to any node of the FCCS network that has a different SYS-ID, on the condition that a
Q.931a Tie Line is established between the different SYS-ID FCCS networks. (Available for Series 7400
software.)

FCCS Network A

(SYS-ID:XXXXXXXXX)

FCCS-Roaming

PS

FCCS

Node A

FCCS-Roaming

Node B

PS

Roaming
Roaming

Q.931a Tie

Line

Roamin g

Roaming

FCCS Network B

(SYS-ID:ZZZZZZZZZ)

FCCS

Node C

Node D

Page 56

NEAX2400 IPX Wireles s Featu re s and S pe cificat io ns

NDA-24313, Issue 1

Call Forwarding - Dropped Calls C-161

C-161 Call Forwarding - Dropped Calls

General Description

This feature provides a call for warding function when a PS encounters a Squelch Disconnec tion (such as PS moving
out of zone, failing to hand over a call, or a sudden power down of the PS) during a two-way connection with a
station/trunk. If this feature is set, the PS can forward the unexpectedly disconnected call to a pre-assigned
forwarding destination, such as a PS, a user of voice mail system, or an analog/D

Note:

This feature is available when CALL FORWARDING PS INCOMING CALL INCOMPLETE is already
assigned to the PS.

Operating Procedure

To set up this feature

1. Pre-set Dialing

a.) Dial the access code to set this feature.
b.) Go off-hook and hear the Service Set Tone.
c.) G o on-hook.

2. Overlap Dialing

a.) Go off-hook and hear the Dial Tone.
b.) Dial the access code to set this feature.
c.) Hear the Service Set Tone.
d.) Go on-hook.

To cancel this feature Note 1

1. Pre-set Dialing

a.) Dial the access code to cancel this featu re.
b.) Go off-hook and hear the Service Set Tone.
c.) G o on-hook.

2. Overlap Dialing

a.) Go off-hook and hear the Dial Tone.
b.) Dial the access code to cance l this f eature.
c.) Hear the Service Set Tone.
d.) Go on-hook.

Note 1:

This feature also can be cancelled by cancelling CALL FORWARDING PS INCOMING CALL
INCOMPL E TE . (Refer to Item 3 under Service Conditions.)

Note 2:

When dialing the cancel acc ess code, whic h this feature has not be assigned, Reorder Tone is returned.

Note 2

term

station, etc.

Service Conditions

1. This feature can be set at each PS, which is already provided with the CALL FORWARDING PS
INCOMING CALL INCOMPLETE feature.

2. The forwarding destination of CALL FORWARDING PS INCOMING CALL INCOMPLETE is also
designated as the destination of this feature.

3. This feature also can be cancelled by cancelling CALL FORWARDING PS INCOMING CALL
INCOMPLETE. However, CALL FORWARDING PS INCOMING CALL INCOMPLETE is solely
cancelled while this feature is maintained, depending on the system data .

4. After this feature is once in service, the function of this feature is still maintained, even if CALL
FORWARDING PS INCOMING CALL INCOMPLETE service is restricted.

NEAX2400 IPX Wireless Features and Specifications
NDA-24313, Issue 1

Page 57

C-161 Call Forwarding - Dropped Calls

Service Cond iti o ns (co nt ’ d)

5. When a call is currently being transferred by this feature, the forwarded party (not the forwarding
destination but the party first connected to the Squelch PS) hears the Ringback Tone.

6. When this feature has been activated during a two-way call betwee n a PS and a station (including P S), the
station now being transferred to the forwarding destination, cannot use “TRF” or “HLD” keys (restriction
is impose d).

7. This feature can be applied to:

• a basic two-way connection between a PS and a station (including PS)

• a basic two-way connection between a PS and a trunk (analog, ISDN, CCIS, TLT)

8. When forwarding destination of this feature can be:

•a PS

• an analog/D

• an Attendant

• a trunk (COT)

•Tie Line

9. When a call ter minates just in the middle o f “service set” access co de dialing (Pre-set Dial ing: before
going off-hook), th e key operati on until this moment goes all null and void.

10. This feature is not available for a two-way connection between a PS and an ATTCON/DESKCON.

11. When a PS attempts an OG call and it ends up in a Squelch Disconnection before connected to the self­node/other node trunk, this feature is not activated.

12. If a Squelch Disconnection occurs just during the following state, this feature is not activated:

• A PS is placed on hold during a two-way connection with a station (including PS)

• A station (including PS) is placed on hold during a two-way connection with a PS

13. When a PS encounters a Squelch Disconnection during a two-way connection with a UCD station, this
feature is not available.

14. When this feature is activated and the forwarded party does not answer, the following occurs:

• When CALL FORWARDING - DON’T ANSWER is assigned at the forwarded party
After a certain period of no answer, the call is shifted to the destination of CALL
FORWARDING - DON’T ANSWER.

• When CALL FORWARDING - DON’T ANSWER is not assigned at the forwarded party
Recall to the Squelch PS is not made, and the forwarded party continues to ring.

15. When a call is forwarded by this feature and also is shifted to another des t ination, the forwarding kind to
be notified to the destination is “CALL FORWARDING PS INCOMING CALL INCOMPLETE”.

16. When this feature is activated, the LCD indication on the D
CALL FORWARDING PS INCOMING CALL INCOMPLETE.

17. When a Squelch Disconnection occurs simultaneously at both PSs in a two-way connection, this feature
is activated by neither PS.

18. The forwarding kind to be reported to MCI is “CALL FORWARDING - DON’T ANSWER”.

19. The assigned data for this feature can be backed up on the HDD/FDD of the PBX.

20. The forwarding destination of this feature is not designated by th e system data.

21. This service does not support the unrestricted digital data.

22. Service conditions for two-line D

a.) This se rv i ce can be assig n e d to b o t h lin e s of this type PS.
b.) When a Squelch Disconnection occurs while a line is in a two-way connection and the other line

is placed on hold, this service is applied to the former line only (two-way connection line only).

term

station

term

PS are shown below:

term

(forwarded party) is identical to that of

Page 58

NEAX2400 IPX Wireles s Featu re s and S pe cificat io ns

NDA-24313, Issue 1

Call Forwarding - Dropped Calls C-161

Interactions

1. When a Squelch Disconnection occurs during a two-wa y connection bet ween a PS and a station (including
PS), the following en s u e a cco rd i n g t o t h e assig ned service(s):

• When AUTOMATIC ANNOUNCEMENT - CALLED PS OUT OF ZONE is assigned to the
Squelch PS
The party, not the Squelch PS, hears the announcement.

• When this feature is assigned to the Squelch PS
The disconnected call is forwarded to the target destination.

• When this feature and AUTOMATIC ANNOUNCEMENT - CALLED PS OUT OF ZONE are
both assigned to the Squelch PS
The disconnected call is forwarded to the target destination, as this feature takes priority over
AUTOMATIC ANNOUNCEMENT - CALLED PS OUT OF ZONE.

• If neither this feature and AUTOMATIC ANNOUNCEMENT - CALLED PS OUT OF ZONE
is assigned to the Squelch PS
No measures are taken. The party, not the Squelch PS, hears the Reorder Tone.

2. A call forwarded by this feature can be answered by the CALL PICKUP - GROUP feature.

3. A call forwarded by this feature can be answered by the CALL PICKUP - DIRECT feature.

4. The Call Waiting service is available for the call forwarded by this feature.

5. When a PS moves to a visitor PB X (when roaming) a nd it encounte rs a Sque lch Disconnection, this fe ature
is not activated .

NEAX2400 IPX Wireless Features and Specifications
NDA-24313, Issue 1

Page 59

I-40 IS D N Data Comm u n ications - 32 kbps

I-40 ISDN Data Communications - 32 kbps

General Description

This feature enables a data terminal connected to a PS to develop the data communications via the 32 kbps
unrestricted digital network. By using this feature, the PS-connected terminals can communicate with the TA
equipment available for V.110 or PCS Internet Access Forum Standard (PIAFS) and also with the terminals
available via LAN. See the example below:

PS

Data Terminal

Data Terminal

Case 1: Data Communication between PSs

Case 2: Data Communication via Digital network

TA-P

(PIAFS/V.110)

TA-P

(PIAFS/V.110)

Data Terminal

PS

TA-P

Case 1

PS

PBX

PRT

CSIZT

ILC TA-P

Multim edia PBX

ZT ZT

Case 2

Case 3

(PIAFS/V.110) Router

PS

TA-P

CCIS (Digital)

LAN

Data Terminal

Data Terminal

Page 60

PS

Data Terminal

Case 3: Data Communication via LAN

Data Terminal

TA-P ZT

PS

TA-P

Multimedia PBX

Multimedia PBX

ZT

PRT

ILC TA-P LAN

CCIS (Digital)

NEAX2400 IPX Wireles s Featu re s and S pe cificat io ns

TA-P

Data Terminal

Data Terminal

NDA-24313, Issue 1

ISDN Data C ommunic at ions - 32 kbps I-40

General Description

Bearer Capability

Between the PBX and ZT, the following message conversion is performed:

1. When originating via Wireless (Low Layer Compatibility element = Without User Information Layer 1
Protocol)

ELEMENT PS AFTER CONVERSION

Bearer

Low Layer

Compatibility

Information Transfer Rate
User Information Layer 1 Protocol
User Rate

Information Transfer Rate 32 kbps 64 kbps

32 kbps

-

-

64 kbps

V.110

32 kbps

2. When originating via Wireless (Low Layer Compatibility element = With User Information Layer 1
Protocol)

ELEMENT PS AFTER CONVERSION

Bearer

Low Layer

Compatibility

Information Transfer Rate
User Information Layer 1 Protocol
User Rate

Information Transfer Rate
User Information Layer 1 Protocol

32 kbps

-

-

32 kbps

V.110

64 kbps

-

-

64 kbps

V.110

3. When terminating to Wireless (Low Layer Compatibility element = Without User Information Layer 1
Protocol)

INCOMING

ELEMENT

STN/TRK AFTER CONVERSION

Bearer

Low Layer

Compatibility

Information Transfer Rate
User Information Layer 1 Protocol
User Rate

Information Transfer Rate 64 kbps 32 kbps

64 kbps

V.110

32 kbps

32 kbps

-

-

4. When terminating to Wireless (Low Layer Compatibility element = With User Information Layer 1
Protocol)

ELEMENT PS AFTER CONVERSION

Information Transfer Rate

Bearer

User Information Layer 1 Protocol
User Rate

Low Layer

Compatibility

NEAX2400 IPX Wireless Features and Specifications
NDA-24313, Issue 1

Information Transfer Rate
User Information Layer 1 Protocol

64 kbps

-

-

64 kbps

V.110

32 kbps

-

-

32 kbps

V.110

Page 61

I-40 IS D N Data Comm u n ications - 32 kbps

Operating Procedure

Use the ATD command for data sending (origination) and the ATA command for answering.

Service Conditions

Conditions between PBX and ZT

1. Only CCITT standardized rate adaption, V.110 or X.30, can be used as the User Information Layer 1
Protocol i n case of data ter m in a tion.

2. Allowed User Rate of the Bearer is 32 kbps only.

term

3. The sub-line of the two-line D
restricted).

Conditions by PS

1. This feature does not support the CALL FORWARDING - DROPPED CALLS [C-161] / AUTOMATIC
ANNOUNCEMENT - DISCONNECTED PS OUT OF ZONE [A-128] / AUTOMATIC
ANNOUNCEMENT - CALLED PS OUT OF ZONE [A-129] feature. Accordingly, if a PS is once out of
zone, any of these features are not provided .

2. Data communication (originating) is not available by using the TRUNK LINE APPEARANCE feature.

3. The Call Waiting service is not available for the PS which is just engaged in data communication.

4. CALL FORWARDING - BUSY LINE, assigned to a PS, does not function if the PS is just engaged in
data communication. Accordingly, if the communication is in prog ress, the third incoming call (including
that by another data terminal) is not forwarded to the target destination (i.e. disconnected).

5. CALL FORWARDING - DON’T ANSWER, assigned to a PS, does not function if the PS is jus t engaged
in data communication. Accordingly, if the communication is in progress, the third incoming call
(including that by another data terminal) is not forwarded to the target destination (i.e. disconnected after
a certain period of time).

6. CALL FORWARDING - ALL CALLS, assigned to a PS, does not function if the PS is just engaged in
data communication. Accordingly, if the communication is in prog ress, the third incoming call (including
that by another data terminal) is not forwarded to the target destination (i.e. disconnected).

PS does not provide this feature (both origination and termination are

Page 62

NEAX2400 IPX Wireles s Featu re s and S pe cificat io ns

NDA-24313, Issue 1

Authorization Code - D

term

PSII A-137

A-137 Authorization Code - D

General Description

An AUTHORIZATION CODE is a numerical code dialed by PS users (up to ten digits), which will override the
station CLASS OF SERVICE - INDIVIDUAL [C-15] for facility access restriction.

Operating Procedure

Procedure 1

• With feature Access Code

1. Go on-hook and receive Dial Tone.

2. Enter the feature Access Code and receive Service Set Tone.

3. Enter the AUTHORIZATION CODE (up to ten digits).

4. Receive Dial Tone.

5. Enter the number to be called.

Procedure 2 (only for LEAST COST ROUTING [L-5] calls)

• Without feature Access Code

1. Go on-hook and receive Dial Tone.

2. Enter the number to be called.

3. If an AUTHORIZATION CODE is required, the caller will receive Special Dial Tone.

4. If Special Dial Tone is received, enter the AUTHORIZATION CODE (up to ten digits) or the call is
denied.

Note:

The feature access code for AUTHORIZATION CODE is a maximum of three digits.

PSII

term

Service Conditions

1. Feature restriction classes of the following services cannot be overridden using this feature.

• PAD LOCK

• Authorization Code Display Elimination

2. The following are conditions when using My Line (L1) and Sub Line (L2) simultaneously. (Two-Line
Operation)

• Wh en one l i ne i s conne cted and the other line is held, the class of the held line is not changed
(remains t h e clas s before changeo ver) and it is changed aft er returning t o th e orig i n al call.

• When both lines are held, the class changeover of earlier-held line is invalid.

3. Users cannot use the ISDN DATA COMMUNICATIONS - 32 kbps service using Authorization Code.

4. Visitor PS of “TTC Q.931a protocol Tie Line with PCS Roaming” is not available.

NEAX2400 IPX Wireless Features and Specifications
NDA-24313, Issue 1

Page 63

C-166 Call Park - D

term

PSII

C-166 Call Park - D

General Description

This feature enables a PS user to “Park” a call (C.O. line, Tie Line, station and PS) by hooking and dialing a Call
Park Access Code , and by dialing the C all Park retr ieval code and the te lephone number that parke d a call, the parked
call can easily be retrieved from any PS/Station within the system. If the user forgets to retrieve the parked call, the
automatic recall function informs the user.

Operating Procedure

To park a call from PS

1. Go hooking (press TRF key).

2. Receive Special Dial Tone.

3. Dial the Cal l Park Ac cess Code.

4. Receive Service Set Tone.

5. Replace the handset.

To retrieve a parked call from the originating station

• Overlap sending procedure

1. Go off-hook.

2. Receive a Dial Tone.

3. Dial the Call Park local retrieval code.

4. The parked call is reconnected.

• Enbloc sending procedure

1. Dial the Call Park local retrieval code.

2. Go off-hook.

3. The parked call is reconnected.

To retrieve a parked call from a different station

• Overlap sending procedure

1. Go off-hook.

2. Receive Dial Tone.

3. Dial the Call Park remote retrieval code and the number of the station that parked the call.

4. The parked call is reconnected.

• Enbloc sending procedure:
When access code operation using enbloc sending is invalid

1. Dial the Call Park remote retrieval code.

2. Go off-hook.

3. Dial the number of the station that parked the call.

4. The parked call is reconnected.

When access code operation using enbloc sending is valid:

1. Dial the Call Park remote retrieval code and the number of the station that parked the call.

2. Go off-hook.

3. The parked call is reconnected.

PSII

term

Page 64

NEAX2400 IPX Wireles s Featu re s and S pe cificat io ns

NDA-24313, Issue 1

Call Park - D

term

PSII C-166

Service Conditions

1. This feature is also available for Sub Line (L2) of a two-li ne D

2. The parked PS cannot hold a terminal.

3. A PS can park only one call at a time.

4. A PS cannot park an Attendant Console.

5. When the Call Park key of Attendant Console key pattern is valid, and the Attendant Console is parking
a PS, the Attendant Console operator can retrieve the PS by dialing the Access Code and Individual
Attendant Identification number which is assigned by “Individual Attendant Access).

Note:

An Attendant Console is not made to recall.

6. When a PS which parks a call does not retrieve the call, it is recalled after fixed time which depends on
Automatic Recall Timer. When a PS parks a call via C.O. line and then the C.O. side goes on-hook, PBX
does not d et ect the release; h ow ever, th e C O T can be rel eased by Auto matic Recall Timer.

7. This feature can be used with all PSs within the system (depending on Service Feature Restriction Class).

8. When the parked PS encounters the squelch disc onnec tion, CALL FORWARDING - DROPPED CALLS
is not available even though it is set.

9. If the PS recalled by Automatic Recall Timer is out of zone, the parked PS user receives Reorder Tone
(ROT).

10. If the parked PS moves out of zone, it is disconnected.

11. The condition of “TTC Q.931a protocol Tie Line with PCS Roaming” is shown below.

term

PS (by using Two-Line Operation).

HOME PBX VISITOR PBX

PS parks a call Available Not Available

PS retrieves a call Available Not Available

PS is parked by terminal Available Available

Note 1:

When a visitor PS originates a call to PS/Station that belongs to the same office, the visitor PS cannot be
parked.

Note 2:

When a PS which parked a terminal moves to the visitor office, and then it is recalled by Automatic Recall
Timer, the terminal receives Reorder Tone.

12. When programming this feature, telephone numbers should be used.

Interactions

The following features cannot be activated to a PS/Station that has been set Call Park:

• BUSY VERIFIC A TION

• CAL L W A IT ING

• ATTENDANT CAMP-ON WITH TONE INDICATION

• EXECUTIVE RIGHT OF WAY - D

term

NEAX2400 IPX Wireless Features and Specifications
NDA-24313, Issue 1

Page 65

G-23 Group Call - Automatic Conference (20-Party)

G-23 Group Call - Automatic Conference (20-Party)

General Description

This feature enables a PS user to call a maximum of “20-Party (self + other 19 members)” conference, only by
dialing a pre-programmed Group Calling Conference Number. If the Group Calling Conference Number is once
dialed, the member PSs/Stations are automatic ally called in assigned order at the interval of every two seconds. This
feature also allows the Station Hunting Group - Circular, and the use of Phantom Telephone Number(s) which is
available for flexible arrangement of conference member tables.

Operating Procedure

1. Dial the Group Calling Conference Number (telephone number/Phantom Telephone Number of
conference leader port).

2. The conference leader hears Ringback Tone.

3. When the first p arty (conferee) answers, Ri n g ba ck T o n e stop s , and t h e conference is in pro gress.

4. The called parties (c onferees) participate in the conference one after another after answering the call.

Note:

While the conference is in progress, the called party may b e release d t o get out of the conference.

5. When the conference leader hangs up, the conference connection is released.

Service Conditions

1. Conference leader and conferee must be a PS/Station.

2. PA-CFTB can be available for Group Calling Conference.

3. The following table shows conditions of CFTB circuit card to use this feature.

MAXIMUM NUMB ER OF

FIRMWARE NAME

CONFERENCE MEMBERS

Firmware SP-1141 20 OFF OFF
Firmware SP-388

(This firmware cannot be used for

8OFFON

cascade connection.)

4. The maximum number of CFTB circuit cards per one conference group is three.

Note:

The number of CFTB circuit cards required to call a conference depends on the maximum number of
conference members per conference group.
2 ~ 8 members (including conference leader): one circuit card
9 ~ 14 members (including conference leader): two circuit cards
15 ~ 20 members (including conference leader): three circuit cards (Maximum)

5. A maximum of 16 digits of Group Calling Conference Number (telephone number/Phantom Telephone
Number corresponding to a conference leader port of CFTB) should be assigned.

6. A user must assign the telephone number for the conferee.

7. By making a group of Station Hunting Group - Circular between conference leader ports or conference
leader ports for cascade connection of multiple sets of CFTB circuit cards, the conference can be held
looking for idle CFTB circuit cards when the dialed port has already been used by others.

KEY SETTING

SW2-2

KEY SETTING

SW2-3

Page 66

NEAX2400 IPX Wireles s Featu re s and S pe cificat io ns

NDA-24313, Issue 1

Group Call - Automatic Conference (20-Party) G-23

Service Cond iti o ns (co nt ’ d)

8. By assigning the Phantom Telephone Number to the telephone number, the maximum number of
conference group per set of CFTB circuit cards is 17 (Phantom Telephone Number: 16 + telephone
number: 1).

9. This service must not be assigned to the ports of LC used for LC-COT connection.

10. If a conference leader hangs up (or is out of zone), the conference will be released.

11. When a conferee is busy or out of zone during a conference call, the conferee is not called.

12. When all conferees are busy, out of zone or they do not answer the conference call, the conference leader
hears Ringb ack T one .

13. When a conferee who answered a conference call goes on-hook before a conferee who is to be called last
in the group is called, and other conferees are busy, out of zone or do not answer the call, a conference
leader receives no tone.

14. ISDN terminal and Attendant Console are not available in this feature.

15. Conference leader cannot call a conference using Blind Transfer.

16. When using this feature, the user must assign Service Feature Restriction Class and Route Restriction
Class, which are different from those of other stations to ports of CFTB circuit card, and also restrict all
outgoing routes by system data. If outgoing trunk is used for this feature, noise or announcement of
another office may be heard.

17. If a PS is in one of the following conditions, Call Forwarding - Dropped Call is not executed.

• When the PS encounters a squelch disconnection while it is in conference.

• Wh en a c o nnected ter mi n al i s i n c onference.

18. If a conferee has been assigned in a UCD group, the conferee is not called.

NEAX2400 IPX Wireless Features and Specifications
NDA-24313, Issue 1

Page 67

S-134 Short Text Messaging Service (STM Service)

S-134 Shor t Text Messaging Servic e (STM Se rvice)

General Description

This feature enables a short text message (STM), once arrived at a mail box of the Short Text Message Server
(external equipment ), to be a utomatic ally d istribu te d to the addr essee PS vi a Open Appli catio n Inte rface (OAI). This
feature also provides a Zip Tone and “TM WAITING” notification on the display (LCD) of the address PS that is
busy, and if the PS is out of zone, the feature makes retransmission of the STM after the PS returns to the zone.

Note:

Operating Procedure

Service Conditions

Note:

This describes STM Facilit ies available for exte rnal STM OAI application. Actual functionality depends on
the application.

1. By using PS function key, users can set a password (four digits or less) to the PS to enter STM (short text
message system) mode.

2. The STM transmitted to the PS while PS’s buffer (maximum ten messages) is busy is temporarily kept in
STM server. When requesting the STM, delete old STM data in the buffer using the function key. Then
the PS automatically requests STM server to retransmit the STM.

1. This feature is available only for My Line (L1) of a two-line D

2. This feature is provided in the same form as that for call termination.

3. STM message transmission route is only one way: STM server → PS

4. An STM can contain 128 byte data in the maximum.

5. The following are not available in this feature.

• Call Forwarding - All Calls

• Call Forwarding - Don’t Answer

• Call Forwarding - Busy Line

• Call Forwarding PS Incoming Call Incomplete

6. This feature is counted as ZT peg count.

7. If the following occur, STM is not distributed, but stays in the mail box of the ST M serv er . The ST M is
safely transmitted later by this feature’s retransmission function.

• Addressee PS is out of zone.

• Addressee PS has a power down.

• The line of addressee PS is busy.

• PS is in a state of hand-over.

When hand-over unexpectedly starts while the message transmission is partially in progress, this feature
sees this as a squelc h disconnection and performs message retransmission after the hand-over is completed.

8. Wireless Roaming is not available in this feature.

9. More than STM server cannot be transmitted to a single PS simultaneously. Only the earliest STM can be
sent safely.

Note

term

PS (not provided for Sub Line (L2)).

Page 68

NEAX2400 IPX Wireles s Featu re s and S pe cificat io ns

NDA-24313, Issue 1

Short Text Messaging Service (STM Service) S-134

Service Cond iti o ns (co nt ’ d)

10. Hardware Requirements: PS and ZT that are both supporting this feature should be used. If other PS/ZT
is used, the following occurs at the PBX side:

• PBX sends an STM request to a PS.

• PBX cannot obtain a response signal from the PS. Also, PBX cannot identify that the PS/ZT is
not compatible with the STM feature.

• PBX judges the PS as in (and returning from) the out-of zone area.

• According to the judgement above, PBX performs adequate processing (PS is judged as
returning from the zone, and a retry of STM request is made).

Interactions

1. The STM is influenced by System Data of Multiple ACDPs (including Multiple IPs).

Note:

For multiple ACDPs, refer to the CallCenterWorX-Enterprise ACD System Manual.

PBX-1

FCCS

PS-1 PS-2

STM Server

PBX-2

STMSTM

A: STM Available NA: STM Not Available : Not u sed

SYSTEM DATA OF PBX-1 SYSTEM DATA OF PBX-2

MULTIPLE

ACDPS

DISPERSION

AGENT

MULTIPLE

ACDPS

DISPERSION

AGENT

PS-1 PS-2

Ineffective  Ineffective  AA
Ineffective
Ineffective




Effective Ineffective Ineffective

Effective Ineffective
Effective Effective

  

 
 

Effective Ineffective Effective Ineffective A NA
Effective Ineffective Effective Effective A NA
Effective Effective Ineffective

  

Effective Effective Effective Ineffective A NA
Effective Effective Effective Effective A A

Note:

NEAX2400 IPX Wireless Features and Specifications
NDA-24313, Issue 1

Shaded a re a s repres e nt invalid configuration.

Page 69

This page is for your notes.

Page 70

NEAX2400 IPX Wireles s Featu re s and S pe cificat io ns

NDA-24313, Issue 1

Movement of PS in NEAX2400 IPX

Movement of PS in NEAX2400 IPX

PCS Community

The SYS-ID is a unique ID which was given in order to manage the PCS system. The area where the SYS-ID is
effective is called PCS Community. Every PCS Community in a FCCS network is given a unique PCS Community
Number (PCN). Each PCN has its own SYS-ID. The PCN is used in stead of the SYS-ID for MAT command, and
this can re duce the ef fect u pon changing the SYS-ID t o som e measur e. The habi tual op eration of the SYS-ID, which
reaches to nine digits for the management purpose, is not needed; therefore easy maintenance can be provided. A
single PCS Community can be assigned in multiple nodes, and a single node can belong to multiple PCS
Communities by using the Tenant service.

PS movement in the NEAX2400 IPX system is classified into four kinds as described below:

1. Stand-by condition movement
Movement of an idle PS within the home PCN area in the home FCCS network (in the FCCS network
accommodating the home node). The event of PS Location Registration occurs only when the PS moves
over the Calling area. Even if a PS is in the Intra-FCCS Roaming or Roaming status, movement of the PS
within the current PCN is also stand-by condition movement. In the NEAX2400 IPX system, the home
PCN can be assigned over the node, however the Calling Area cannot. Becau se of this, the event of PS
Location Registration occurs whenever an idle PS moves over the node.

2. Hand-Over
Movement of a PS engage d i n communica tion within t he home PCN ar ea in t he home FCCS ne twork. The
event of Hand-Over occurs regardless of the Calling Area.
Even if a PS is in the Intra-FCCS Roaming or Roaming status, movement of the PS engaged in
communication within the current PCN is also Hand-Over. In the NEAX2400 IPX system, the call
enga ged in c ommunic a tion is supported even in the case of Hand-Over over the node.

3. Intra-FCCS Roaming
Effective only in the home FCCS network. Roaming Request is made to the home node whenever
Roaming occurs out of the home FCCS network. This pattern simplifies the internal operation. The call
engaged in communication is not supported.

4. Roaming
PS Location Registration to the ZT in another PCN than the home PCN is called Roaming. The call
engaged in communication is not supported.

NEAX2400 IPX Wireless Features and Specifications
NDA-24313, Issue 1

Page 71

Movement of PS in NEAX2400 IPX

FCCS-I

Home PCN-a

Home

A

B

E

F

Node-W Node-X Node-Y Node-Z

C

D

G

H

PCN-b

First Visit Node

I

J

FCCS-II

PCN-c

K

L

PCN-d

M

MOVE TO

MOVE FROM

A

HOME NODE

HOME PCN

C

OTHER NODE

HOME PCN

E

HOME NODE

OTHER PCN

G

OTHER NODE

OTHER PCN

A, B HOME

NODE

HOME PCN

Stand-by

condition

Movement

H-O

Stand-by

condition

Movement

H-O

Intra-FCCS

Roaming

Intra-FCCS

Roaming

C, D

OTHER

NODE

HOME PCN

Stand-by
condition

Movement

H-O

Stand-by
condition

Movement

H-O

Intra-FCCS

Roaming

Intra-FCCS

Roaming

E, F HOME

NODE

OTHER

PCN

Intra-FCCS

Roaming

Intra-FCCS

Roaming

Stand-by

condition

Movement

H-O

Stand-by

condition

Movement

H-O

G, H

OTHER

NODE

OTHER

PCN

Intra-FCCS

Roaming

Intra-FCCS

Roaming

Stand-by

condition

Movement

H-O

Stand-by

condition

Movement

H-O

I

OTHER

FCCS

FIR ST VISIT

NODE

FIRST PCS

K

OTHER

FCCS

OTHER

NODE

FIRST PCN

J

OTHER

FCCS
FIRST

VISIT

NODE

OTHER

PCN

L

OTHER

FCCS

OTHER

NODE

OTHER

PCN

YET OTHER

FCCS

Roaming Roaming Roaming Roaming Roaming

Roaming Roaming Roaming Roaming Roaming

Roaming Roaming Roaming Roaming Roaming

Roaming Roaming Roaming Roaming Roaming

M

Page 72

NEAX2400 IPX Wireles s Featu re s and S pe cificat io ns

NDA-24313, Issue 1

Movement of PS in NEAX2400 IPX

MOVE TO

MOVE FROM

I

OTHER FCCS

FIRST VISIT

NODE FIRST

PCN

K

OTHER FCCS

OTHER NODE

FIRST PCN

J

OTHER FCCS

FIRST V IS IT

NODE OTHER

PCN

L

OTHER FCCS

OTHER NODE

OTHER PCN

M

YET OTHER

FCCS

A, B HOME

NODE

HOME PCN

C, D

OTHER

NODE

HOME PCN

E, F HOME

NODE

OTHER

PCN

G, H

OTHER

NODE

OTHER

PCN

Roaming Roaming Roaming Roaming

Roaming Roaming Roaming Roaming

Roaming Roaming Roaming Roaming

Roaming Roaming Roaming Roaming

I

OTHER

FCCS

FIR ST VISIT

NODE

FIRST PCS

Stand-by

condition

Movement

H-O

Stand-by

condition

Movement

H-O

Roaming

Note

Roaming

Note

K

OTHER

FCCS

OTHER

NODE

FIRST PCN

Stand-by
condition

Movement

H-O

Stand-by
condition

Movement

H-O

Roaming

Note

Roaming

Note

J

OTHER

FCCS

FIRST

VISIT

NODE

OTHER

PCN

Roaming

Note

Roaming

Note

Stand-by
condition

Movement

H-O

Stand-by
condition

Movement

H-O

L

OTHER

FCCS

OTHER

NODE

OTHER

PCN

Roaming

Note

Roaming

Note

Stand-by
condition

Movement

H-O

Stand-by
condition

Movement

H-O

Roaming Roaming Roaming Roaming Roaming Roaming Roaming Roaming

M

YET OTHER

FCCS

Roaming

Roaming

Roaming

Roaming

Roaming or

Stand-by

condition

Movement

(depending

on the case)

Note:

NEAX2400 IPX Wireless Features and Specifications
NDA-24313, Issue 1

This pattern is treated as Roaming by re-Roaming to the home node in FCCS-I.

Page 73

This page is for your notes.

Page 74

NEAX2400 IPX Wireles s Featu re s and S pe cificat io ns

NDA-24313, Issue 1