NEC Expres5800/A2040b, Expres5800/A2010b, Expres5800/A2020b, Expres5800/A1040b Installation Manual
Page 1
- 1 August 2016
855-911221-105-A
LAN Driver
Installation Guide
(Broadcom v17.2)
Expres5800/A2040b, A2020b, A2010b, A1040b
Page 2
- 2 August 2016
855-911221-105-A
Contents
Preface ............................................................................................................................................ 3 1.
1.1. The target server........................................................................................................................ 3
1.2. Target software .......................................................................................................................... 3
1.3. Target Driver Version ................................................................................................................. 3
1.4. Registration Trademark ............................................................................................................. 3
Workflow LAN driver update process ............................................................................................. 4 2.
Preparation ...................................................................................................................................... 5 3.
3.1. Workflow preparation process ................................................................................................... 5
3.2. Confirmation of LAN driver version............................................................................................ 6
3.3. Preparation of module ............................................................................................................... 9
3.3.1. Prepare the update module ............................................................................................. 9
3.3.2. Prepare the recovery module ........................................................................................... 9
3.4. Save the setting of LAN driver ................................................................................................. 10
3.5. Stop the WSFC node service .................................................................................................. 12
3.6. Stop the EXPRESSCLUSTER service .................................................................................... 13
LAN driver update ......................................................................................................................... 14 4.
4.1. LAN driver installation .............................................................................................................. 14
After LAN driver install .................................................................................................................. 15 5.
5.1. Workflow after LAN driver install ............................................................................................. 15
5.2. Reset LAN driver...................................................................................................................... 16
5.3. Start the WSFC node service .................................................................................................. 19
5.4. Start the EXPRESSCLUSTER service .................................................................................... 21
Rollback procedure of LAN driver ................................................................................................. 22 6.
6.1. Old LAN driver installation ....................................................................................................... 22
Notice ............................................................................................................................................ 23 7.
7.1. About the operation by remote desktop .................................................................................. 23
7.2. Account of operation ................................................................................................................ 23
7.3. Notice of using Hyper-V ........................................................................................................... 23
7.4. Notice of update ....................................................................................................................... 23
Appendix ....................................................................................................................................... 24 8.
8.1. List of LAN driver setting default value .................................................................................... 24
8.2. List of stored path of recovery driver ....................................................................................... 25
Page 3
- 3 August 2016
855-911221-105-A
Preface 1.
Thank you very much for purchasing our product.
This installation guide explains how to set up the LAN Drivers.
1.1. The target server
Refer to the URL below and check the target server.
http://www.58support.nec.co.jp/global/download/index.html
-> Click model name(product name).
-> Click “LAN Driver Module(V17.2)(Windows Server 2012 R2/Windows Server 2012)” in “Other update”.
1.2. Target software
*1 Above information is based on 2016/07
Refer the Server Configuration Guide for the latest information.
The latest drivers are published on our NEC Express5800 Support Website.
*2 Refer to the Server Configuration Guide for correspondence Option LAN Board.
1.3. Target Driver Version
The target driver version before and after update are listed in the following.
If the driver version in use is not listed in the following, this update is not necessary.
Related to the confirmation method of installed version, please refer to [3.2 Confirmation of LAN driver version].
Target software
Target driver version
(b57nd60a.sys)
After update version
(b57nd60a.sys)
Windows Server 2012
15.6.0.10
17.2.0.2
Windows Server 2012 R2
16.2.0.4
17.2.0.2
1.4. Registration Trademark
Microsoft, Windows, Windows Server, Hyper-V are registered trademark or trademarks of the Microsoft in the U.S.
and other countries. Broadcom, the pulse logo, Connecting everything, the Connecting everything logo, NetXtreme,
Ethernet@Wirespeed, LiveLink™, and Smart Load Balancing™ are among the trademarks of Broadcom Corporation
and/or its affiliates in the United States, certain other countries, and/or the EXPRESSCLUSTER is registered
trademark of the NEC corporation. In addition, TM and an R mark are not specified in the test.
Abbreviated designation
Software Production Name
Windows Server 2012
Microsoft® Windows Server® 2012 Standard
Microsoft® Windows Server® 2012 Datacenter
Windows Server 2012 R2
Microsoft® Windows Server® 2012 R2 Standard
Microsoft® Windows Server® 2012 R2 Datacenter
Microsoft® Windows Server® 2012 R2 Foundation
Page 4
- 4 August 2016
855-911221-105-A
Workflow LAN driver update process 2.
Important
This document is based on using the Windows Server Failover Clustering
(Afterward WSFC) and EXPRESSCLUSTER. If WSFC is not used, skip step [3.5
Stop the WSFC node service] and [5.3 Start the WSFC node service]. If
EXPRESSCLUSTER is not used, skip step [3.6 Stop the EXPRESSCLUSTER
service] and [5.4 Start the EXPRESSCLUSTER service].
Start
End
3. Preparation
4. LAN driver update
5. After LAN driver install
Page 5
- 5 August 2016
855-911221-105-A
Preparation 3.
Important
・Sign in the system from local console by administrator account for executing
the operation below.
・If using Hyper-V and not using WSFC or EXPRESSCLUSTER, shutdown all the
Guest OS and release the setting of auto boot up before the LAN driver
update.
3.1. Workflow preparation process
Start
End
3.2 Confirmation of LAN driver version
3.3 Preparation of module
3.5 Stop the WSFC node service
3.6 Stop the EXPRESSCLUSTER service
3.4 Save the setting of LAN driver
Page 6
- 6 August 2016
855-911221-105-A
3.2. Confirmation of LAN driver version
Check the driver version by the procedure below. When the version is equal or newer than the following version,
installation is not necessary.
1. Open the Device Manager icon on the Control Panel window.
2. Double-click the Broadcom NetXtreme Gigabit Ethernet icon on the Device Manager.
Page 7
- 7 August 2016
855-911221-105-A
3. Click the Driver Details on the Driver tab.
4. Confirm the version in Driver tab, and also the File version of the corresponding
driver(b57nd60a.sys) in Driver File Details.
If the version in use is not the target, this update is not necessary.
Page 8
- 8 August 2016
855-911221-105-A
Target OS
Target driver version before
update
(b57nd60a.sys)
Driver version after update
(b57nd60a.sys)
Windows Server 2012
15.6.0.10
17.2.0.2
Windows Server 2012 R2
16.2.0.4
17.2.0.2
Page 9
- 9 August 2016
855-911221-105-A
3.3. Preparation of module
3.3.1. Prepare the update module
1. Refer to the URL below and download the GVO-010516-G01_xxxxxxxxxxxxxxxxxx.zip (x
is an expression of arbitrary numbers).
http://www.58support.nec.co.jp/global/download/index.html
-> Click model name(product name).
-> Click “NEC Express5800/A2000 series,A1040b LAN Driver Module(V17.2)(Windows
Server 2012 R2/Windows Server 2012)” in “Other update”.
2. Create a temp folder directly under the system drive.
(e.g., C:\temp\)
3. Unzip GVO-010516-G01_xxxxxxxxxxxxxxxxxx.zip, copy the BCOM172 folder in the temp
folder.
(e.g., C:\temp\BCOM172\)
3.3.2. Prepare the recovery module
For recovering to the original module, please use the DVD of EXPRESSBUILDER, support kit or
the released module in Website.
Regarding the source for obtaining the recovery module, please refer to [8.2 List of stored path of
recovery driver] to prepare it in advance.
Besides, if the recovery module is downloaded from Website, please extract it to an arbitrary folder.
* If you want to use the DVD of EXPRESSBUILDER, DVD device is necessary for reading the
DVD.
Page 10
- 10 August 2016
855-911221-105-A
3.4. Save the setting of LAN driver
For updating or recovering the LAN driver, the setting of LAN driver returns to default. Please obtain the setting by the
following procedures before updating or recovering the LAN driver.
1. Open Windows PowerShell as administrator and run the following command to output the
setting of LAN driver to a text file.
Get-NetAdapterAdvancedProperty | sort-object –property DisplayName,Name |
select-object Name,DisplayName,DisplayValue > C:\temp\adapter_property.txt
Page 11
- 11 August 2016
855-911221-105-A
2. Open the saved adapter_property.txt file in 1. and compare it with the default values of
current driver version in [8.1 List of LAN driver setting default value]. For each network adapter,
if any parameter or value is not default, note them down.
3. Run the following command to output the network adapter information to a text file.
Get-NetAdapter > C:\temp\adpter_info.txt
4. Open the saved adapter_info.txt file in 3. and note down the network adapter name which
Status is Not Present. Not Present means that it is disabled now. Since it will become
enabled after updating or recovering the LAN driver, please refer to [5.2 Reset LAN driver] for
disabling the corresponding network adapter.
[adapter_property.txt]
Name DisplayName DisplayValue
---- ----------- ------------
LAN1 802.3az EEE (Copper Only) Disable
LAN2 802.3az EEE (Copper Only) Disable
LAN3 802.3az EEE (Copper Only) Disable
LAN4 802.3az EEE (Copper Only) Disable
LAN1 ARP Offload Enabled
LAN2 ARP Offload Enabled
LAN3 ARP Offload Enabled
LAN4 ARP Offload Enabled
LAN1 EEE Control Policies (Copper Only) Optimal Power and Performance
LAN2 EEE Control Policies (Copper Only) Optimal Power and Performance
LAN3 EEE Control Policies (Copper Only) Optimal Power and Performance
LAN4 EEE Control Policies (Copper Only) Optimal Power and Performance
LAN1 Ethernet@WireSpeed (Copper Only) Enable
LAN2 Ethernet@WireSpeed (Copper Only)
LAN3 Ethernet@WireSpeed (Copper Only)
LAN4 Ethernet@WireSpeed (Copper Only)
LAN1 Flow Control Disabled
LAN2 Flow Control Auto Negotiation
LAN3 Flow Control Auto Negotiation
LAN4 Flow Control Auto Negotiation
:
[adapter_info.txt]
Name InterfaceDescription ifIndex Status MacAddress LinkSpeed
---- -------------------- ------- ------ ---------- --------LOM3 Broadcom NetXtreme Gigabit Ethernet #5 18 Up 44-8A-5B-6C-C2-FF 1 Gbps
LOM2 Broadcom NetXtreme Gigabit Ethernet #4 17 Up 44-8A-5B-6C-C2-FE 1 Gbps
LOM1 Broadcom NetXtreme Gigabit Ethernet #7 20 Up 44-8A-5B-6C-C2-FD 1 Gbps
NIC3_4 Broadcom NetXtreme Gigabit Ethernet #11 30 Up 58-C2-32-82-8B-F3 1 Gbps
NIC3_3 Broadcom NetXtreme Gigabit Ethernet #12 31 Up 58-C2 -32-82-8B-F2 1 Gbps
NIC3_2 Broadcom NetXtreme Gigabit Ethernet #10 29 Not Present 58-C2-32-82-8B-F1 0 bps
NIC3_1 Broadcom NetXtreme Gigabit Ethernet #15 34 Not Present 58-C2-32-82-8B-F0 0 bps
If the value of "DisplayValue"
is changed from default, note
down the Name, DisplayName
and DisplayValue.
Page 12
- 12 August 2016
855-911221-105-A
3.5. Stop the WSFC node service
1. Open the Failover Cluster Manager from Server Manager.
2. Move the all resource of target node to another node.
3. Select the Nodes displayed on the left of Failover Cluster Manager.
4. Right-click the target node for driver update from the node list.
5. Select the Stop Cluster Service from More Actions.
6. Open the Services from Server Manager.
Page 13
- 13 August 2016
855-911221-105-A
7. Right-click the Cluster Service.
8. Select the Properties.
9. Change the Startup type on General Tab to Disabled. Select the OK.
3.6. Stop the EXPRESSCLUSTER service
Refer the following website for more information.
http://www.nec.com/en/global/prod/expresscluster/en/support/manuals.html
-> Reference Guide
-> Chapter 10 The system maintenance information
-> Replacing the network card
* Perform the procedures prior to the replace of network card.
Shut down the system and then start up it again. After that, Go to [4 LAN driver update].
Page 14
- 14 August 2016
855-911221-105-A
LAN driver update 4.
Refer the notice before driver update.
Important
Sign in the system from local console by administrator account for executing
the operation below.
4.1. LAN driver installation
1. Run a command prompt as administrator. Enter the following command at the command
prompt.
cd C:\temp\BCOM172\LAN\
(For file info, refer the [3.3.1 Prepare the update module])
2. Enter the following, and then press Enter key.
Windows Server 2012
INSTALL_WS2012.bat
Windows Server 2012 R2
INSTALL_WS2012R2.bat
3. When the following message is displayed, restart the system.
Installation Completed!
4. Check that the driver version is 17.2.0.2. By following [3.2 Confirmation of LAN driver
version].
Page 15
- 15 August 2016
855-911221-105-A
After LAN driver install 5.
Important
・Sign in the system from local console by administrator account for executing
the operation below.
・If using Hyper-V and not using WSFC or EXPRESSCLUSTER, shut down all the
Guest OS if necessary and reset the system to auto boot up after this chapter.
5.1. Workflow after LAN driver install
Start
End
5.2 Reset LAN driver
5.3 Start the WSFC node service
5.4 Start the EXPRESSCLUSTER service
Page 16
- 16 August 2016
855-911221-105-A
5.2. Reset LAN driver
Refer the following steps for resetting the parameter of LAN driver.
1. Open Control Panel and click Network and Sharing Center.
2. Select Change adapter settings for displaying Network and Sharing Center screen.
Page 17
- 17 August 2016
855-911221-105-A
3. According to the noted network adapter name in 4. of [3.4 Save the setting of LAN driver],
right-click on the target adapter and select Disable to disable the adapter.
4. Right-click on each physical network adapter (Device name: Broadcom NetXtreme Gigabit
Ethernet) and click Properties.
Page 18
- 18 August 2016
855-911221-105-A
5. Click on Configure and then select Advanced tab. Change the values of corresponding
Property based on the noted values in 2. of [3.4 Save the setting of LAN driver].
* Please refer to Handoff of setting value in [8.1 List of LAN driver setting default value] for
confirming which property is needed to reset.
6. Restart the system.
Page 19
- 19 August 2016
855-911221-105-A
5.3. Start the WSFC node service
Refer the following steps for starting the service of node which has been stopped in [3.5 Stop the WSFC node
service].
1. Open the Services from Server Manager in the node which LAN driver updated.
2. Right-click the Cluster Service in service screen and select the Properties.
Page 20
- 20 August 2016
855-911221-105-A
3. Change the Startup type to Automatic on General Tab then select OK.
4. Right-click the Cluster Service at service screen and select the Start.
5. Open the Failover Cluster Manager from Server Manager.
6. Select the node from the left side of Failover Cluster Manager.
Page 21
- 21 August 2016
855-911221-105-A
7. Right-click the target node for driver update from the node list. Select the Start Cluster
Service from More Actions.
5.4. Start the EXPRESSCLUSTER service
Refer to the following URL.
http://www.nec.com/en/global/prod/expresscluster/en/support/manuals.html
-> Reference Guide
-> Chapter 10 The system maintenance information
-> Replacing the network card
* Perform the procedures beyond replacing network card procedure.
In addition, no need to reset the network configuration.
Page 22
- 22 August 2016
855-911221-105-A
Rollback procedure of LAN driver 6.
Important
・Sign in the system from local console by administrator account for executing
the operation below.
・If necessary, execute [3.5 Stop the WSFC node service] and [3.6 Stop the
EXPRESSCLUSTER service] in advance.
・If you use Hyper-V and not use WSFC or EXPRESSCLUSTER, shut down all
the Guest OS and release the setting of auto boot up before the rollback of
LAN driver.
・After rollback, execute [5 After LAN driver install] and reset the network
setting.
6.1. Old LAN driver installation
1. If the attached DVD of EXPRESSBUILDER is used for recovery, insert the DVD in the optical
device.
2. Open command prompt as administrator. Move the current path to the stored path of target
driver by cd command by referring to Stored path in [8.2 List of stored path of recovery
driver].
* The command example is written below when target device is A2040b and target OS is
Windows Server 2012.
cd /d <DVD drive letter>:\002\win\winnt\ws2012\b57nd60a\bcom\ws2012\lan\bco
m\drvinst\156a0401\x64
3. Run the following command and press <Enter> key to start the installation.
setup /s /v"/qn DOWNGRADE=Y"
4. Open Event Viewer and confirm that the following event is logged in the application log.
Close the Event Viewer and command prompt and then restart the system.
* If the following event is displayed, wait until it is logged.
* After the installation is completed, there may be some cases that the system is restarted
automatically.
In that case, also confirm that the following event is logged after the system is restarted.
5. After the system is restarted, confirm that the version of the installed driver is the one before
update by following [3.2 Confirmation of LAN driver version].
6. After the confirmation, please perform [5 After LAN driver install].
Page 23
- 23 August 2016
855-911221-105-A
Notice 7.
This section describes notice of LAN driver. Read the following notes or information before installation.
7.1. About the operation by remote desktop
For all the operation described in this document, it has to be performed from the local console. Remote desktop of OS
or remote operation tool is not supported.
7.2. Account of operation
For all the operation described in this document, it has to be performed by logging on with an administrator account.
In addition, open command prompt or Windows PowerShell as Administrator.
7.3. Notice of using Hyper-V
If you use Hyper-V and not use WSFC or EXPRESSCLUSTER, shut down all the Guest OS before the LAN driver
installation.
7.4. Notice of update
The network is disconnected when updating the LAN driver. Please stop all the jobs of using network before the
update.
Page 24
- 24 August 2016
855-911221-105-A
Appendix 8.
8.1. List of LAN driver setting default value
List of default value (v15.6.0.10/16.2.0.4)
* In "Handoff of setting value", "-" means the value does not change after the update or recovery.
For the others, the values are set based on the above table after the update or recovery.
* For the properties with hatching, the corresponding values are set depending on your environment.
For the other properties, it is recommended to set to the default value.
* Regarding "Ethernet@WireSpeed", there are some cases that the confirmed value in [3.4 Save the
setting of LAN driver] is blank.
In that case, the value becomes "Enable".
* For the property with "Copper Only", there are some cases that the property is not existed depending
on the adapter or driver version but there is no problem on it.
* Regarding "Network Address", if the confirmed value in [3.4 Save the setting of LAN driver] is blank,
the value becomes "None".
Property
Default value
Handoff of setting value
After update
After recovery
802.3az EEE (Copper Only)
Disable
-
Disable
ARP Offload
Enabled
-
-
EEE Control Policies (Copper Only)
Optimal Power and
Performance
-
-
Ethernet@WireSpeed (Copper
Only)
Enable
-
Enable
Flow Control
Rx & Tx Enabled
-
Rx & Tx
Enabled
Interrupt Moderation
Enabled
-
-
Jumbo Mtu
1500
-
1500
Large Send Offload V2 (IPv4)
Enabled
-
Enabled
Large Send Offload V2 (IPv6)
Enabled
-
Enabled
Maximum Number of RSS Queues
RSS 1 Queue
-
RSS 1 Queue
Network Address
None
-
-
NS Offload
Enabled
-
-
Priority & VLAN
Priority & VLAN Enabled
-
-
Receive Buffers
Default
Default
Default
Receive Side Scaling
Enabled
-
-
Speed & Duplex (Copper Only)
Auto Negotiation
-
-
TCP/UDP Checksum Offload (IPv4)
Rx & Tx Enabled
-
-
TCP/UDP Checksum Offload (IPv6)
Rx & Tx Enabled
-
-
Transmit Buffers
500
500
500
Virtual Machine Queues
WS2012 : Disabled
WS2012R2 : Enabled
Disabled
-
VLAN ID
0
-
-
VMQ VLAN Filtering
Disable
-
-
Wake On Magic Packet
Enabled
-
Enabled
Wake On Pattern Match
Enabled
-
Enabled
WOL Speed (Copper Only)
Lowest Speed Advertised
-
Lowest Speed
Advertised
Page 25
- 25 August 2016
855-911221-105-A
8.2. List of stored path of recovery driver
Target device
Target OS
Driver
version
Source for obtaining driver
Stored path
NEC Express5800/A2040b
NEC Express5800/A2020b
NEC Express5800/A2010b
NEC Express5800/A1040b
Windows Server 2012
15.6.0.10
EXPRESSBUILDER of server
\002\win\winnt\ws2012\b57nd60a\bcom\ws
2012\lan\bcom\drvinst\156a0401\x64
Windows Server 2012 R2
16.2.0.4
http://www.58support.nec.co.jp/g
lobal/download/w2012r2/GlobalA2040b_A2020b_A2010b_A104
0b.html
\\winnt\ws2012r2\lan\bcom\drvinst\160204
01\x64
Loading...