CHARACTERISTICSYMBOLMIN.TYP.MAX.UNITTEST CONDITION
Collector Cutoff CurrentICBO0.1
Emitter Cutoff CurrentIEBO0.1
Collector Saturation VoltageVCE(sat)0.5VhFE = 10,IC = 5 mA
DC Current GainhFE60120VCE = 5 V, IC = 5 mA
Gain Bandwidth ProductfT3.05.5GHzVCE = 5 V, IC = 5 mA
Feed–back CapacitanceCre0.70.9pFVCB = 5 V, IE = 0, f = 1 MHz
Insertion Power Gain|S21e|
2
5.0dBVCE = 5 V, IC = 5 mA, f = 1 GHz
*1 Pulse Measurement PW ≤ 350 µs, Duty Cycle ≤ 2 %
*2 The emitter terminal and the case shall be connected to the guard terminal of the three–terminal capacitance bridge.
hFE Classification
RankFB
µ
AVCB = 15 V,IE = 0
µ
AVEB = 1 V, IC = 0
*1
*2
Marking73
hFE60 to 120
2
Page 3
TYPICAL CHARACTERISTICS (TA = 25 °C)
2SC5005
TOTAL POWER DISSIPATION vs.
AMBIENT TEMPERATURE
150
Free Air
50
– Total Power Dissipation – mW
T
P
050100150
TA – Ambient Temperature – °C
COLLECTOR CURRENT vs.
BASE TO EMITTER
24
V
CE
= 5 V
16
DC CURRENT GAIN vs.
COLLECTOR CURRENT
200
V
100
50
– DC Current Gain
FE
h
20
10
0.5 151050
10
220
C
– Collector Current – mA
I
GAIN BANDWIDTH PRODUCT vs.
COLLECTOR CURRENT
V
CE
= 5 V
I
C
= 5 mA
8
6
CE
= 5 V
8
– Collector Current – mA
C
I
00.21.0
V
COLLECTOR CURRENT vs.
COLLECTOR TO EMITTER VOLTAGE
0.40.60.8
BE
– Base to Emitter Voltage – V
30
m
IB = 160 A
20
10
– Collector Current – mA
C
I
0210
V
CE
– Collector to Emitter Voltage – VIC – Collector Current – mA
46 8
m
140 A
120 A
m
m
100 A
80 A
m
60 A
m
m
40 A
m
20 A
4
2
– Gain Bandwidth Product – GHz|S
T
f
0
0.5151050
14
V
CE
f = 1 GHz
12
220
C
– Collector Current – mA
I
INSERTION POWER GAIN vs.
COLLECTOR CURRENT
= 5 V
10
8
6
4
– Insertion Power Gain – dB
2
e|
2
21
0
0.51102050
25
3
Page 4
2SC5005
MAXIMUM AVAILABLE GAIN
INSERTION POWER GAIN vs. FREQUENCY
20
15
10
5
– Insertion Power Gain – dB
2
e|
21
|S
MAG – Maximum Available Gain – dB
0
0.1
0.20.512
f – Frequency – GHz
MAG
S
21e
2
V
CE
= 5 V
IC = 5 mA
FEED-BACK CAPACITANCE vs.
COLLECTOR TO BASE VOLTAGE
No part of this document may be copied or reproduced in any form or by any means without the prior written
consent of NEC Corporation. NEC Corporation assumes no responsibility for any errors which may appear in this
document.
NEC Corporation does not assume any liability for infringement of patents, copyrights or other intellectual
property rights of third parties by or arising from use of a device described herein or any other liability arising
from use of such device. No license, either express, implied or otherwise, is granted under any patents,
copyrights or other intellectual property rights of NEC Corporation or others.
While NEC Corporation has been making continuous effort to enhance the reliability of its semiconductor devices,
the possibility of defects cannot be eliminated entirely. To minimize risks of damage or injury to persons or
property arising from a defect in an NEC semiconductor device, customer must incorporate sufficient safety
measures in its design, such as redundancy, fire-containment, and anti-failure features.
NEC devices are classified into the following three quality grades:
“Standard“, “Special“, and “Specific“. The Specific quality grade applies only to devices developed based on
a customer designated “quality assurance program“ for a specific application. The recommended applications
of a device depend on its quality grade, as indicated below. Customers must check the quality grade of each
device before using it in a particular application.
Standard: Computers, office equipment, communications equipment, test and measurement equipment,
audio and visual equipment, home electronic appliances, machine tools, personal electronic
equipment and industrial robots
systems, anti-crime systems, safety equipment and medical equipment (not specifically designed
for life support)
Specific: Aircrafts, aerospace equipment, submersible repeaters, nuclear reactor control systems, life
support systems or medical equipment for life support, etc.
The quality grade of NEC devices in “Standard“ unless otherwise specified in NEC's Data Sheets or Data Books.
If customers intend to use NEC devices for applications other than those specified for Standard quality grade,
they should contact NEC Sales Representative in advance.
Anti-radioactive design is not implemented in this product.
M4 94.11
8
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.