Page 1
1
HOT BEAM 280
MOVING HEAD BEAM
Net Weight：19KG
Color Temperature：9300K
POWER：470W
Page 2
2
ITEM
Item...........................................................................................................................02
1.Product introduce ...............................................................................................03
2.Fixture size........................................................................................................... 03
3.Parts introduce.................................................................................................... 04
4.Safety information............................................................................................... 05
5.Packing and shipping ......................................................................................... 07
6.AC power............................................................................................................. 08
7.Lamp model and replace.................................................................................... 08
8.Control Panel...................................................................................................... 11
9.Control panel operate.........................................................................................11
10.DMX Channels................................................................................................. 14
11.PCB Driving board.......................................................................................... 18
STATEMENT
The product is good packing when ship out the factory. All users should strictly abide by the
warnings and instructions stated in this manual, any damage and results due to misuse and the
neglect of this operating manual will be excluded from the deal responsibility this manual will not
informed in additionally if have technical changes.
Page 3
3
PRODUCTION INTRODUCE
Thank you for choose this HOT BEAM280 products, this model is the moving head light which is
the latest development of the smart, efficient products, beautiful shape, smooth R & D, combined
with the advanced technology of today's stage lighting products with international advanced
electronic control technology and excellent user-friendly industrial design , fully comply with CE
standard, accepted international standard DMX512 signal mode.
This moving head lights, use ceramic luminescent film reflector as a condenser system, coupled
with the high-quality optical lens components, broadband voltage, a clear pattern, sharp and
uniform output light efficiency. Intelligent LCD display module, the English language selection
mode, intuitive operating menu, shortcut.
Hot Beam280, have 16/24 international standard DMX512 channels optional Horizontal scan: 540
° vertical scanning 270 ° (16bit precision scanning) electronic correction, dot-matrix display, four
touch switch LCD + single-Key flying shuttle can spin. The can be inverted 180 °, the color wheel
is combined with white and 14 colors. 2 Gobo wheels: 9 patterns + white effect round by 8 prism+
6 prism and atomization function. 0-100% mechanical dimmer, support mechanical strobe and
variable strobe effect, strobe macro function. The optical system of the lens group electric
focusing, the beam angle of 0 to 4 ° with overheating protection function
Moving head lights are widely used in television, disco, dance halls, nightclubs, large-scale
performances and other professional venues
2 FIXTURE SIZE
Size：385（L）×365（W）×589（H）mm
Page 4
4
3. PARTS INTRODUCE
01
02
03
04
05
06 07
01 — Lens
02 — Body
03 — Tilt Lock
04 — Arm
05 — Pan Lock
06 — Handle
07 — Light base
01 02 01 02 03 04 05 06 07
0 — Control
panel
02 — Control wheel
01 — 3 Pin dmx In
02 — 5 Pin dmx in
03 — Power switch
04 — Power in
05 — 3 Pin dmx out
06 — 5 pin dmx out
07 — Fuse
Page 5
5
4. SAFETY INFORMATION
Safety warning message
This product is only suitable for professional use, and does not apply to security for other purposes.
After you got the lights, please check the package whether have any damage caused by
transportation. If there is any damage, do not use this fixture, and please contact the dealer or
manufacturer as soon as possible.
This product is only suitable for indoor, IP20 protection class. Lamps should be kept dry to avoid
Moisture, overheating or dusty environment. Prevent lamps come into contact with water or any
other liquid.
The use of this product should pay attention to: fire, heat, electric shock, ultraviolet radiation, the
lamp to explode or
Shedding caused serious or fatal injury.
Need to read the instructions before use energized or installing.
Follow through the operation of security methods and pay attention to the warning signs on the
specification and equipment. If you have any problem for how to safely operate the equipment.
Please contact your dealer.
4.1 2.1 ANTI-HIGH TEMPERATURE
ta =40°C
Please don’t use the equipment if the temperature above 40℃
4.2 BURST PREVENTION
The lens should be changed if had damaged or any problems. Don’t change the
non-original manufacturer lens.
Len size：128*32mm
4.3 TO PREVENT FALLING WOUNDING
Please don’t move the package by one person only.
When Hang the fixture, please must verify that the facilities to be able to
withstand the weight of the lamps at least 10 times more.
Please make sure the Mounting hardware is strong enough no any damage, and
insurance for the safety rope as auxiliary security fixed in other facilities will
need to verify before installation. Installing or removing the equipment, to make
the pulley below the work location
4.4 UA PROTECTION AND THE BULB EXPLOSION
Prohibit straight viewpoint with exposed bulbs to avoid UV damage to the eyes;
Page 6
6
Do not use the equipment without the lens screen and the lid;
The lens and the light head covers should be timely replaced if any damage to rupture
The Fixture should be used with the protection screen together.
4.5 PREVENTION OF ELECTIC SHOCK
The electrical connection must only be carried out with corresponding qualifications;
Before installing, make sure you use the power voltage lamps must comply with the identified
power, voltage and have an overload or leakage protection;
Each lamp must be properly grounded, installed in accordance with the relevant standards;
Cut off the power when stall or replace the lamp and the fuse;
Prohibit the use of a lightning storm or wet environment.
4.6 TO PREVENT BURNING OR FIRE
1. The fixture can be mounted directly on the surface of ordinary combustible
material.
2. Do not short-circuit temperature protection switch or fuse, use the specified type of fuse.
3. The equipment must be installed away from inflammable and explosive materials.
4. The equipment should be projected range of 3 meters away objects and projectiles
temperature less than 60 ° C; ---- 3.0m.
5. Fan or ventilation, at least in the range of 0.5 meters can not be an obstacle.
6. Do not place any object on the lens.
7. Handling at least allow the device to cool for 20 minutes.
8. Do not replace the non-original parts.
4.7 TRANSPORT PROTECT LOCK
In order to protect the light, there is a protect lock; During the transport , the lock will closed
keeping the item in safety state.
4.8 ABOUT PACKING
1. Before packed, make sure power is off, and wait for at least 20mins for cooling down.
2. Before clean the fixture, make sure X, Y axis protect lock closed.
3. After packed by plastic bag, high-lift the fixture with two handles besides the product. put
the product into the fly-case up-side-down.
4. After packed the product, put the accessory into the accessory case, then closed and lock the
fly-case.
5. Fly-case only up stacked two layers. Prohibited upside down
6. When packed with carton box, equipment should be put into the foam first, then set into a
carton, pay attention to the vertical position.
。
Page 7
7
4.9 UNPACKING
Note: Before unpacking check the damage is whether due to the transportation or not, if you find any
such damage, please do not use this item, and contact with the dealer or manufacturer as soon as
possible.
1. Open the fly-case, and discover the inside plastic bag.
2. High-lift the product by two handles beside the bottom base and move it out.
3. Before power on, make sure you have opened the X, Y axis lock!
Attention! One product only can accept one input one output.
Hot BEAM280 DMX cable include 3 contact pins:
Pin 1, FOR GROUND; Pin 2 connected to the negative polarity signal; The pin
3connected to the positive polarity signal.
DMX512 cable must use the professional shielded twisted pair cable; standard
loudspeaker cable is not reliable to control the long-range data. 24AWG cable is
suitable for more than 300 meters long-distance signal transmission and must add\
DMX 512 signal amplifier.
Do not use two outputs to separate the connection, if separate a continuous connection
to branch, DMX512 splitter is necessary.
Attention! Do not overload the connection. One continuous connection can only
connect up to 32 devices.
If use the DMX512 splitter. At first connect DMX512 Splitter input terminal to
controller .And then connected from the splitter output terminal to next device.
Do as above guide to connect other device, and finally coupled with terminal insertion
5.PACKAGE
Hot Beam280 packed with fly-case of two in one ,or carton box.
Attach follow accessory.
ACCESSORY
CONTENT QUANTITY
USER MANUL 1
HANG FIXTURE 1
SIGNAL CABLE 2
Page 8
8
6. AC POWER
VOLTAGE, POWER, FUSE SPECIFICATION
Input Voltage
Total Power Frequency
110~240V 470W 50/60HZ
Fuse voltage
Electronic current Specification
250V 6A 5×20
6.1 POWER PROTECT
The equipment must be operated by professionals; Make sure that the voltage of
power supply must be comply with the voltage identified on the lamp, and must have
an overload or leakage electrical protection.
ATTENTION!
Factory has equipped the standard 3 pin plug socket. Connect the power supply as
below table.
If lamp cable is damaged, replacement should be operate by factory or qualified
staff. Any question, please contact professionals or talk to a qualified electrician.
Live wire(L) Null(N) Ground wire
RED BLUE Yellow +Green
7. LAMP
7.1 LAMP DESCRIPTION
LAMP MODEL POWER OF LAMP LIFE/HOUR COLOR TEMPERATURE
OSRAM SIRIUS HRI
280 W 2200 HOURS 9300K
WARNING! There is a safety hazard or damage if install similar bulb
To reduce the risk of damage to light ,do change the lamp before using
time over 125% of lamp life .
LAMP REPLACE
Attention! When replace the lamp is forbidden to touch lamp with bare hand, to avoid the greasy
dirt stains filament. filament must be kept clean
1. Disconnect the power. Before replace lamp, fixture need 20 minutes for lamp
cooling. Fasten the head with Y axis protect lock in 60 ° position.
1. Use cross screwdriver to open the light body cover(picture 1)
（1）
Page 9
9
2. After open the cover,you can see the lamp inside,please wait the lamp be cool after used but not
touch it in hot status.(picture 2)
（2）
3. One hand press the lamp holder,another hand hold the lamp,and pull out the wires(picture 3,4)
（3） （4）
4.after take apart the lamp, please check the inside glasses, clear it will make the light better
effect.(Picture 5)
（5）
5.installed the lamp after replaced.
Page 10
10
8.COLOR WHEEL, GOBO WHEEL
STATIC GOBO
ROTATE GOBO
HOT BEAM Have 6 linear prism and 8 facet prism.
Page 11
11
8.CONTROL PANEL
Display: to display all information of fixture.
Control wheel: can turn right,left and enter.
9.CONTROL PANEL MENU OPERATE
Main Menu Submenu 1 Submenu 2 Function SET Function description
DMX Address
001-512 DMX Address number set
"Natu" Normal
"ShowReve"
"Revl" reverse 180°
"Chin" Chinese 中文
"Language"
"English" English
"BrigSett" 000-255 Brightness set
"60S "
Backlight close after delay
60S "Backligh"
"Ligh" Backlight light always
90S
Menu back to mainmenu
after dalay 90S MenuBack"
"Off " Menu back not automatic
open
Backlight blinking when no
dmx
Backflah
off
Backlight not blinking when
no dmx
Display
"Return " ▲ return
"Xreverse"
"Off " PAN SCAN Normal
"Open" Pan Scan Reverse
"Off " Tilt Scan normal
"Yreverse"
"Open" Tilt Scan Reverse
"Feature "
"XY Setup"
"XY Speed"
"Fast"
PAN/TILT FAST
SPEED
DISPLAY
CONTROL
WHEEL
Page 12
12
"NORM"
PAN/TILT
NORMAL
"Solw" PAN/TILT SLOW
"360 ", "360 " Pan Angle 360°
"540 ", "540 " Pan Angel 540°
"X Angle"
"630 ", "630 " Pan Angel 630°
"Off "
PAN/TILT optical
sensor testing off
"XY Fback"
"Open"
PAN/TILT optical
sensor testing on
Return
▲ Return
"Shortcut"
"Off "
Shortcust off for
colors and gobos
"Open"
Shortcust open for
colors and gobos
"FullColr"
"Off " half color function
"Open" full color function
"ChanMode"
"Smal" Simplify mode
"Stan" Standard mode
"ReceMode"
"DMX " Accept DMX
"Wire" Accept Wireless
"Auto" AutoRun
"RunMode "
"Slve"
Accept other signal
control
"Musc" Sound active
"Auto"
Inside program Run
automatically
"SigClear"
"Off " keep signal data
"Open" clear signal data
DMX Reset
Off Dmx reset not accept
Open Dmx reset accept
Return
▲ Return
"Wink" Lamp off
"Default "
"Ilum" Lamp on
"Wink" Lamp off by manual
"Control "
"Ilum" lamp on by manual
"Off "
Close other signal
control the lamp
"DmxLamp "
"Open"
Open other signal
control the lamp
"LampSett"
"LampTime" 0000-9999 Lamp used time recorded
Page 13
13
★
Password input Enter
"ClearTim"
"Ilum" Clear Lamp time
"Wink" Lamp off
"LampStat"
"Ilum" Lamp on
Return
▲ Return
"WorkHour
"
0000-9999
working hours memo
for connect power
"Times
"
0000-9999 Open times memo
"Fan1Rota"
0000-9999 Fan rotation speed 1
"Fan2Rota"
0000-9999 Fan rotation speed 2
"Version "
XMOA Version
Spare time
No limit No limit time
Spare cut
No limit No limit times
"InfoSee "
Return
▲ Return
"Control "
Chan 00-Chan
40 Control the Channels
"Factory "
★
Password input Enter
"Fold" Recover Factory set
"Save" Save factory set
"Defaults"
★
Password input Enter
"Fold" Recover to default
Redress
★
Password input enter
Reset01-10 Set the motors
Chdefine
Color wheel
Rotation 001
Channels set by
define
000……040
Channels set by
define
"Brightne"
★
Password input Enter
"TimeLimi" 0000-9999
Open fixture time
limit
"TimsLimi" 0000-9999 fixture times limit
TimeCLEA clear
Clear the time of
used
CutClea clear
Clear the times of
used
"Passwor1" 000-255 Revise password 1
"Passwor2" 000-255 Revise password 2
"Passwor3" 000-255 Revise password 3
"Passwor4" 000-255 Revise password 4
"X Drivin" 000-255 pan main drive gear
"X Driven" 000-255 Pan slave drive gear
"AssiTool"
"Y Drivin" 000-255 Tilt main drive gear
Page 14
14
"Y Driven" 000-255 Tilt slave drive gear
"LampPowe" "Off " Ballast earthed
"total 5V",
"Open" Ballast 5V
"YAngle " 000-255
Tilt angel rotation
set
"Return " 000-255 return
"Checksum" 01-10"
Check Cabrilate data
Return
▲ Return
CHANLEVE
Chan1..140 Show the dmx address
Color...focus Display the status
MotorRst
Return
▲
All Reset'' "Annu" Cancel
"Exec" Reset
"Annu" Cancel
XY Rst
PAN/tilt
RESET
"Exec" Reset
"Annu" Cancel
EffecRst
Effect reset
"Exec" Reset
"ExitMenu"
▲ Exit
10.DMX Channels
MODE 1 MODE 2 DMX Value Description
1 1
0－255
Pan
2 *
0－255
Pan Fine
3 2
0－255
Tilt
4 *
0－255
Tilt Fine
5 3
0－255
Pan/Tilt speed
6 4 Micro
0－19
Empty
20－24 Energy-saving mode（230W）
25－129
Empty
130－139
Lamp on by dmx
140－149
PAN/TILT reset
150－159
Empty
Page 15
15
160－169
Small motors reset
170－199
empty
200－209
Whole unit reset
210－229
empty
230－239
Lamp off by dmx
240－255
empty
7 5 Colors
0－8
White
9－17
Deep Red
18－26
Deep Blue
27－35
Yellow
36－44
green
45－53
Magenta
54－62
Light blue
63－71
red
72－80
Deep green
81－89
Amber
90－98
blue
99－107
orange
108－116
CTO
117－127
blue
128－129
white+blue
130－134
blue+CTO
135－138
CTO+orange
139－143
Orange+blue
144－147
blue+amber
148－152
Amber+deep green
153－157
Deep green+red
158－161
Red+light blue
162－166
Light blue+magenta
167－171
magenta+green
172－176
Green+yellow
177－180
Yellow+deep blue
181－185
Deep blue+deep red
186－189
Deep red+white
190－220
Run from fast to slow
221－250
Run from slow to fast
251－255
Color change when sound
control
8 * empty
9 6 empty
7 Static gobo
Page 16
16
0－3
empty
4－9
Gobo 1
10－15
Gobo 2
16－21
Gobo 3
22－27
Gobo 4
28－33
Gobo 5
34－39
Gobo 6
40－45
Gobo 7
46－51
Gobo 8
52－57
Gobo 9
58－63
Gobo 10
64－69
Small beam 1
70－75
Small beam 2
76－87
Small beam 3
Gobo shaking from slow to
fast
88－95
Gobo 1
96－103
Gobo 2
104－111
Gobo 3
112－119
Gobo 4
120－127
Gobo 5
128－135
Gobo 6
136－143
Gobo 7
144－151
Gobo 8
152－159
Gobo 9
10
160－167
Gobo 10
168－175
Small beam 1
176－183
Small beam 2
184－199
Small beam 3
200－255
Static gobo run from slow to
fast
Rotate gobo
0－8
empty
9－17
Gobo 1
18－26
Gobo 2
27－35
Gobo 3
36－44
Gobo 4
45－53
Gobo 5
54－62
Gobo 6
63－71
Gobo 7
72－80
Gobo 8
81－89
Gobo 9
11 8
Gobo shaking from slow to
Page 17
17
fast
90－97
Gobo 1
98－106
Gobo 2
107－115
Gobo 3
116－124
Gobo 4
125－133
Gobo 5
134－142
Gobo 6
143－151
Gobo 7
152－160
Gobo 8
161－169
Gobo 9
171－179
Gobo 9 not move
180－217
Run from fast to slow
218－255
Run from slow to fast
Gobo rotation
0－127
index
128－177
Run from slow to fast in anti
clockwise
178－203
stop
12 9
204－255
Run from fast to slow in
clockwise
13 *
0－255
empty
prism
0－19
empty
20－75
6 linear prism
14 10
76－255
8 facet prism
Prism rotation
0－127
index
128－191
Run from fast to slow in
clockwise
192－193
empty
15 11
194－255
Run from slow to fast in anti
clockwise
16 12 Frost
0－64
empty
65－255
linear frost
17 13 zoom
0－255
Linear zoom
18 *
0－255
Zoom fine
19 14
0－255
focus
20 *
0－255
Zoom fine
Page 18
18
21 *
0－255
empty
22 15 strobe
0－31
Strobe close
32－63
Strobe open
64－95
Strobe from slow to fast
96－127
Strobe open
128－143
Fast to slow,slow close fast
open
144－159
Slow to fast,fast open slow
close
160－191
Strobe open
192－223
Random strobe from slow to
fast
224－255
Strobe open
23 16 dimmer
0－255
Linear dimmer
24 * empty
11. PCB Driving board
01
02
放大调焦八棱镜六棱镜
八棱镜自转
固图
色盘
旋图
图自转 隔热片
频闪
频闪 六棱镜自转
六棱镜自
转定位
DMX
风机
风机1
调焦定位
色盘定位
固图定位
旋图定位
放大定位
风机2
X轴 Y轴
X轴定位
X轴光耦
Y轴定位
Y轴光耦
风机1
风机2
DMXOUT
温控
温控
DMXIN
12VIN
Loading...