NcSTAR APRLSG User Manual

GREEN LASER WITH WEAVER STYLE MOUNT

 This Green Laser is designed to mount directly to your firearm as an advantage of

quick target acquisition. Use of the laser will not replace the use of other sighting
devices in regards to accuracy, but it will certainly aid in locating your target
with ease.

 This Green Laser mounts easily to almost any Picatinny or weaver style base in

any configuration that you choose.

 Included in the package are two types of switches: a standard on & off cap

switch(4), and a coil pressure momentary type switch(10). Also included is the
specially designed weaver style mount(1), two different allen wrenches, and a
CR123A battery.

 Always be sure that the unit is off when not in use to preserve battery life.

 DANGER:

EMITTED FROM THE APPERTURE.

AVOID DIRECT EYE EXPOSURE TO LASER BEAM. LASER RADIATION IS

MOUNTING:

 CAUTION: BEFORE BEGINNING INSTALLATION OF YOUR GREEN

LASER BE SURE THAT THE FIREARM IS UNLOADED. ALWAYS
PRACTICE SAFE FIREARMS HANDLING PROCEDURES.

Your new Green Laser is designed to mount directly to just about any weaver style or
Picatinny rail. To install, first loosen all three main mounting screws(2) using the provided allen
wrench. Next, the laser must be positioned so that the unit is right side up. To perform this
operation, remove the cap on the front of the laser housing(3) by twisting it counter
clockwise. Locate the reference leveling arrows(5) on the face of the laser. The arrow
pointing to the “U” i s the arrow that should be pointing straight up. Twi st the entire laser unit
within the mount(1) to get it square. When the arrows(5) are perfectly square up and to the
right you have successfully aligned your laser. Next, place the laser and mou nt(1) unit onto
the weaver style/Picatinny base of your f irearm. The mount is equipped with a removable
recoil lug(11) to provide strength and stability to the mounting connection. Once you have
the mount(1) in the desired position, it is now time to tighten all of the mounting screws (2).
Be sure not to over tighten the mounting screws(2) to avoid stripping them. Also, be sure that
the mounting location for the laser allows for proper function and movement all of parts of
the firearm.

ZEROING:

 WHEN OPERATING ANY TYPE OF FIREARM ALWAYS USE PROPER

EYE AND EAR PROTECTION. BE SURE TO USE YOUR FIREARM IN AN
AREA THAT IS PERMISABLE UNDER LOCAL, STATE, AND FEDERAL
LAW.

Begin the zeroing process by first turning your laser to the on position by either twisting the rear
on/off cap(4), or by depressing the pressure switch pad(10). Set up a target at the desired
distance. Place your laser beam on the center of the target. Be sure to secure the firearm so
that it will not move when fired. Fire a few shots to see where the projectiles land in relation to
the laser beam. Adjust the laser to match the shot grouping using the provided allen wr ench.
To perform this action, begin removing the front cap of the laser housing(3) by twisting it counter
clockwise. By examining the face of the laser you will see that there are two small adjusting
screws, one with a “U” (meaning up) which is your elevation adjuster(6), and the other with an
“R” (meaning right) which is your windage adjuster(7). There are also referenc e arrows that
wrap around the adjuster screws(6 &7) that indicate the direction to turn the screw in order to
move the laser to the desired location. For instance, when you want to move the laser beam up
you can see that you must turn the “U” adjuster screw(6) clockwise. So to move the laser beam
down you must turn the “U” adjuster screw(6) counter clockwise. After adjusting the laser beam
to match the location of the shot grouping, fire a few more shots to confirm zero. If the laser is
still not zeroed then follow the sam e procedure again making small adjustments until the desired
level of accuracy is achieved. Using a laser bore sighter will also make the zeroing process a
little easier. Another method is to zero the laser beam to the iron sights of the firearm if they are
available. After the zeroing process is complete, be sure to reinstall the front cap(3) to protect
the laser from damage.

INSTALLING THE BATTERY:

Your new Green Laser uses one 3 volt lithium battery which is type CR123A. Always use this type
of battery for best performance results, and to avoid damage to the laser. To install the battery,
simply remove the rear cap switch(4) by turning it counter clockwise. Next, place the battery
into the battery housing(14) with the positive side facing out towards the on/off cap switch(4).
Twist the on/off cap switch(4) back onto the rear of the laser. To use the coil pressure switch(10),
remove the standard on/off cap switch(4) by turning counter clockwise. Remove the spring
insert(12) from the threaded coupling(13) portion of the switch by gently pushing it out. String
the pressure pad side(10) of the coil through the inside part of the coupling(13). Pull the pad a ll
the way through until the battery conne ction(8) portion of the coil becomes flush with
coupling(13). Now twist the coupling(13) onto the rear of the lase r unit until tight. If this
procedure was done correctly, you should se e the laser beam appear every time the pressure
switch pad(10) is depressed. Always be sure that the unit is off when not in use to preserve
battery life.