NcSTAR AAPRLS User Manual

AAPRLS INSTRUCTIONS

1) Mount Bolt Holes

2) Side to Side ON/ OFF Switch

3) Rail Clamp Tab

4) Windage Adjustment

5) Rail Clamp

6) Allen Head Bolt

7) Rail Grooves

8) Laser Aperture

SPECIFICATIONS:

 Maximum output power: <5mW
 Wavelength: 635-655 nm
 Battery type: AG13 or LR44 (1.5V button cell battery)
 Requires two Batteries

 Length: 2.25”
 Width: 1.11”
 Height: 0.90”
 Weight: 1 oz.

LOW PROFILE PISTOL RED LASER

 PLEASE FOLLOW ALL OF THE DIRECTIONS IN THIS MANUAL CAREFULLY.
 CAUTION: ALWAYS PRACTICE SAFE FIREARMS HANDLING!
 BE SURE THAT THE FIREARM IS UNLOADED AND SAFE BEFORE PERFORMING ANY OF THE FOLLOWING

PROCEDURES!

 BE SURE THAT THE FIREARM IS POINTED IN A SAFE DIRECTION AT ALL TIMES!
 CAUTION: AVOID SHINING THE LASER IN YOUR EYES OR INTO ANYONE ELSE’S EYES!

FEATURES:

 Sleek compact low profile design.
 Designed to be securely mounted onto most Weaver/ Picatinny style rails.
 Easy to reach Side to Side On/Off switch
 Laser is fully adjustable for Windage and Elevation.

INSTALLATION:

To mount the laser onto a Weaver/ Picatinny style rails, first unscrew and remove the Allen Head Bolt from the

mount of the laser using the supplied Allen wrench. Set aside the Rail Clamp and Allen Head Bolt.

Place and position the laser onto the firearm rail so that a recoil slot aligns up with one of the laser Mount Bolt Holes.
Insert the Allen Head Bolt through the laser body & firearm rail recoil slot and attach the Rail Clamp to the opposite side of
the laser body. Use the Allen wrench to tighten the Allen Head Bolt into the Rail Clamp. Make sure that the Rail Clamp slot is
interfacing with the Rail Clamp Tab on the side of the laser body.

Tighten the Allen Head Bolt until it is snug. Be careful to not over-tighten the Mount Bolt or it may cause damage to
the laser. Your laser is now securely mounted and ready for use.

REMOVAL:

9) Elevation Adjustment

10) Windage Adjustment

11) Battery Door

12) AG13 or LR44 type Batteries

(Two Each Required)

Using the supplied Allen Wrench and carefully loosen (counter-clockwise) the Allen Head Bolt in the mount, when
you have removed the Allen Head Bolts the laser can be removed from the rail.

ON/OFF SWITCH FUNCTION:

The laser is equipped with a Side to Side ON/OFF Switch. First, make sure the laser is pointed in a safe direction. To
turn the laser ON, push the right side of the ON/OFF Switch to the Left. To turn the laser OFF, push the left side of the
ON/OFF Switch to the Right.

WINDAGE AND ELEVATION ADJUSTMENT:

To adjust the Windage of the laser, insert the provided Allen wrench into the Windage Set Screw located on the Left
side of the laser body. Turn the Windage Set Screw Clockwise to adjust Left and Counter-clockwise to adjust Right.

To adjust the Elevation of the laser, insert the provided Allen wrench into the Elevation Set Screw located on the bottom of
the laser body. Turn the Elevation Set Screw Clockwise to adjust laser Down and Counter-clockwise to adjust the Laser Up.

TIP: The quickest method to zero your laser is to first adjust the laser to your iron sights. Then make the
necessary fine adjustments at the shooting range.

BATTERY REPLACEMENT:

To replace the batteries in your laser, first turn the laser to the OFF
position. The Battery Cap is the round cap with a slot machined into it, located on
the bottom of the laser body. Use a flat blade screw driver or small coin to turn
the Battery Cap Counter Clockwise for removal.

Once the Battery Cap is removed, remove the old batteries and discard it
in the proper manner. The 2nd battery will sometimes stick to the inside of the
Battery Cap. Only use new AG13 or LR44 batteries with the laser. DO NOT use a
different type of battery, as this may cause damage to the unit. DO NOT mix old
batteries with new batteries.

Place the new batteries into the laser, making sure that both of the
battery’s Positive Sides (+) are facing out and that the batteries are centered in
the cavity. Once the batteries are in place, place the Battery Cap over the top
battery and screw the cap Clockwise until the cap is flush with the bottom of the
laser body. If there is some resistance or the cap does not close flush, make sure
the bottom battery is centered in the cavity, so that the cap can screw down and
around both batteries. Next, test the function of the laser. If the laser does not
turn ON, check to make sure that both of the batteries are installed correctly.