EN
M5
M5 - 29/02/2016 09:25:00
USER INSTRUCTIONS AND SAFETY
Congratulations on your purchase of an N-Com product.
N-Com M5 was made using the most advanced technologies and the best
materials. Long-running tests and thorough system development have allowed
the highest audio quality to be achieved.
For additional information about M5 visit the website www.n-com.it
Firmware Version: 1.0x
REFERENCE STANDARDS
The products of the N-Com line are in compliance with standards as per the table below:
M5
The Bluetooth system complies with the main safety requirements and
other applicable provisions of Directive 99/5/CE, Directive 2009/65/EC,
Directive 2011/65/CE, Directive 2012/19/EU
Battery
charger
Directive 2006/95, 2004/108, 2009/65/EC, 2011/65/CE, 2012/19/EU,
2009/125/CE
Battery Directive 2006/66
The Declarations of Compliance can be downloaded from the website www.n-com.it
(Download section).
Model: M5 FccID: Y6MNCOM9
R-NZ
Model: WRC FccID: Y6MNCOM11
R-NZ
Bluetooth is a registered trademark property of Bluetooth SIG, Inc.
Contents
1. WARNINGS AND SAFETY.................................................................................................4
1.1.Road safety ................................................................................................................................................................4
1.2.Switching on the system in safe environments.........................................................................................4
1.3.Interferences..............................................................................................................................................................4
1.4.Appropriate use .......................................................................................................................................................4
1.5.Qualified personnel ................................................................................................................................................5
1.6.Accessories and batteries....................................................................................................................................5
1.7. Disposal .....................................................................................................................................................................5
2. CONTENT OF THE PACKAGING ......................................................................................6
3. INSTALLATION....................................................................................................................7
3.1.Positioning the speakers and the microphone..........................................................................................7
3.2.Installing the e-box ................................................................................................................................................8
3.3.Positioning the Bluetooth keypad .................................................................................................................11
3.4.Operating of the Bluetooth keyboard .........................................................................................................11
4. FUNCTION KEYS...............................................................................................................11
5. BASIC FUNCTIONS...........................................................................................................12
5.1.Auto On / Off Function.......................................................................................................................................12
5.2.N-Com Wizard and N-Com App....................................................................................................................12
5.3.Pairing up with Bluetooth devices.................................................................................................................12
6. MOBILE PHONE................................................................................................................13
6.1.Friend Number .......................................................................................................................................................13
6.2.Managing two mobile phones (or Bluetooth devices).........................................................................14
7. MUSIC VIA BLUETOOTH – A2DP BLUETOOTH PROTOCOL ....................................14
8. MUSIC VIA CABLE ............................................................................................................14
9. SATELLITE NAVIGATOR FOR MOTORCYCLES............................................................15
9.1.Navigators on Smartphone (Smart Navi System)...................................................................................15
10. FM RADIO..........................................................................................................................15
11. EMERGENCY STOP SIGNAL (ESS)..................................................................................16
12. RIDER-PASSENGER INTERCOM.....................................................................................16
12.1.Rider-Passenger intercom pairing up .......................................................................................................16
12.2.Rider-Passenger intercom function............................................................................................................16
13. BIKE-TO-BIKE INTERCOM...............................................................................................17
13.1.Bike-to-Bike Intercom Affiliation (Standard configuration) ............................................................17
13.2.Bike-to-Bike intercom function ....................................................................................................................18
14. SETTING MODE ................................................................................................................19
15. BATTERY AND RECHARGE..............................................................................................19
15.1.Low battery signal..............................................................................................................................................19
15.2.Charging the system .........................................................................................................................................19
16. SUMMARY TABLE OF CONTROLS – STANDARD CONFIGURATION .....................20
17. LIMITED WARRANTY.......................................................................................................22
17.1.Warranty coverage.............................................................................................................................................22
17.2.Exclusions and limitations of the coverage ............................................................................................22
17.3.Validity of this limited warranty ...................................................................................................................22
17.4.Procedure for the forwarding of claims ...................................................................................................23
17.5.Product identification .......................................................................................................................................23
18. WARRANTY REGISTRATION FORM..............................................................................24
EN
4
1. WARNINGS AND SAFETY
Read this User Manual carefully, as well as the simple rules listed below. Failure to comply with these rules may lead
to dangerous situations.
Caution: The product cannot be used in official or non-official competitions, motordromes, circuits, racing tracks and
the like.
Caution: Installation of the N-Com M5 system results in a weight increase of approximately 100 g, which is added to
the weight of the helmet and of the other accessories.
Warning: The electronic components of the N-Com system mounted inside the helmet are not waterproof.
Consequently, make sure the inside of the helmet, including the comfort padding, does not get wet in order to
avoid damage to the system. If it does, remove the N-Com system and the helmet comfort padding and let it
air dry. Disconnect the battery connector and let it dry as well.
1.1. Road safety
Always obey all Traffic Regulations in force. While riding the motorcycle, your hands should always be engaged in
actually riding the vehicle. Any operation to the N-Com system must be carried out with the vehicle stopped.
Specifically:
Set your cell phone on automatic answer (see the cell phone instructions to do this).
If your cell phone is not equipped with this function, first stop your vehicle in a safe area, in compliance with
Traffic Regulations and then answer the call.
Do not make any calls while riding. Stop your vehicle in a safe place in compliance with Traffic Regulations,
and then make the call.
Adjust the volume so that it does not cause a disturbance or distraction while riding and at the same time
allows you to distinctively hear background noises.
Do not operate your cell phone or other devices connected to N-Com while riding your motorcycle.
In all cases, obey the Traffic Regulations and remember that riding the motorcycle has absolute priority over
any other maneuver.
The M5 system is equipped with an emergency brake light (ESS – Emergency Stop Signal). The ESS system IS
NOT intended to replace the stop or brake lights fitted on the motorcycle, consequently its operation alone is
not enough for proper brake signaling.
Make sure that the use of the emergency brake light (ESS – Emergency Stop Signal) is not in conflict with the
regulations in force in the country where you will be travelling.
1.2. Switching on the system in safe environments
When using the N-Com system, comply with all limitations and instructions related to the use of cell phones.
Do not turn on your cell phone or the N-Com system whenever their use is forbidden or when the devices
can cause interference or dangerous situations.
Turn off while refueling. Do not use the N-Com system in filling stations. Do not use the device near
combustible materials or chemical products.
Turn off in proximity to explosive materials.
1.3. Interferences
All phones and devices with wireless signal transmission are subject to interferences that may affect the
performance of the device connected to them. These interferences are not ascribable to a defect of the N-Com
system.
1.4. Appropriate use
Use the device only in the normal position, as described in the product documentation. Do not attempt to
disassemble, tamper with or modify any part of the N-Com system.
Caution: Adjust the volume of the N-Com system (where provided) and of the audio sources connected to it before
you use the system on the road.
Caution: Adjusting the volume to very high levels may cause damage to your hearing.
M5
5
Caution: Adjust the volume of the N-Com system (where provided) and of the audio sources connected to it so as to
avoid audio reproduction at high volumes. Constant exposure to high audio volumes may damage your
hearing.
Caution: An incorrect installation of the system in the helmet may alter the aerodynamic and safety characteristics of
the helmet itself, thus creating dangerous conditions. Install the N-Com system according to the instructions
provided in the product documentation. In case of doubt, please contact your local N-Com dealer.
Warning: Listening to other equipment should not interfere with driving the vehicle, which must be the top priority
at all times. Carry out all operations on the electronic equipment and on the N-Com system with the vehicle
stopped, in compliance with Traffic Regulations.
Caution: The N-Com system allows reception of the FM radio signal. Any radio license fees are to the user’s charge.
1.5. Qualified personnel
Only qualified personnel can carry out technical assistance on this product. In case of any malfunction, always
turn to your local dealer.
The helmet is a safety device. Tampering with it and/or with the electronic system inside the helmet, in
addition to invalidating the product warranty, can also lead to dangerous situations.
1.6. Accessories and batteries
Only use the type of batteries, battery chargers and accessories approved by Nolan for the specific model.
The use of a battery type different from the recommended one may lead to dangerous situations and
invalidate the warranty.
Contact your local dealer to see about the availability of approved accessories.
When disconnecting the power supply cable of any accessory or of the battery charger, always grab and pull
the plug not the cable.
Do not use batteries for purposes other than the prescribed ones.
Never use batteries or battery chargers that turn out to be damaged.
Do not short-circuit the battery.
Keep the battery at a temperature between 0° / +32°C (charging); -20° / +55°C (in use).
Danger of fire or explosion: do not throw the batteries into a fire nor expose them to high temperatures!
Do not throw out batteries together with household refuse. The batteries should be disposed of in
compliance with local regulations.
Do not wear the helmet while the battery is recharging.
The helmet should never be left within the reach of unsupervised children in order to prevent damage to
their health caused by access to the batteries.
Wireless keypad battery CR2016
M5 system battery Li-Po 523450P Litio 3,7V – 1000 mAh
Battery charger S-TR-009L 100/240V – 50/60 Hz 5V - 0.5 A
1.7. Disposal
Refer to this user manual and to manuals related to other parts of the N-Com system in order to disassemble the
system from the helmet. Once the system has been disassembled, dispose of it according to the following
instructions:
The presence of a crossed-out wheelie bin indicates that in the European Union the product is
subject to separate collection at the end of its useful life.
Do not dispose of these products together with undifferentiated urban waste.
The proper disposal of obsolete equipment contributes to preventing possible negative consequences on
people’s health and on the environment.
For more detailed information on the disposal of obsolete equipment, contact your municipality, a waste
disposal service or the store where the product was purchased.
EN
6
2. CONTENT OF THE PACKAGING
The N-Com M5 package contains:
e-box M5 Bluetooth wireless keypad Wiring system
Microphone for
full-face helmets
Flexible boom microphone Velcro kit
Fixing feet kit USB battery charger PC connection cable
E-box safety block Microphone windscreen
M5
7
3. INSTALLATION
3.1. Positioning the speakers and the microphone
Fig. 1
Remove the protective film from the Velcro of
the speakers;
Position the speakers near your ears, so that they
stick perfectly to the helmet.
N.B.: If possible, position the speakers
underneath the comfort padding of the helmet.
Install the microphone
Fig. 2
Flexible boom microphone – recommended
Position the swivel part of the microphone with
the Velcro/adhesive part between helmet shell
and the padding, so that the microphone is
properly positioned in front of your mouth.
Caution: make sure that the side of the
microphone support with the writing “N-Com”
is facing inward.
Fig. 3
Wire microphone
In case it is not possible to use the swivel
microphone, install a wire microphone.
Use the Velcro/adhesive to secure the
microphone inside the helmet, so that it is in
front of your mouth.
N.B.: This type of microphone is more
recommended for full-face helmets.
EN
8
Fig. 4 Fig. 5
Connect the microphone with the counterpart on the wiring (Fig. 4).
Pass the wiring e-box connector through, out of the back of the helmet, so that it can be hooked up
to the e-box afterwards (Fig. 5).
3.2. Installing the e-box
Fig. 6
The M5 e-box must be positioned in the back of
the helmet, using the adhesive feet supplied as
standard equipment.
Thoroughly clean the surface of the helmet
where the feet will be applied;
Insert the fixing feet in the device;
Make sure the e-box is properly positioned on
the helmet shell.
If necessary, depending on the different types of helmets, replace one or more thin feet with thicker
ones, until you find the combination that allows the e-box to properly stick to the helmet (Fig. 7-10).
Fig. 7 Fig. 8 Fig. 9 Fig. 10
M5
9
Important: Should you wish to use the emergency brake light (see Chapter 10), you need to position
the M5 e-box so that it is vertical or with an inclination of +/-30° with respect to the vertical axis
while you are riding, so as to allow the triaxial accelerometer to properly measure the motorcycle
deceleration. Based on the type of helmet used and the riding style, choose the combination of
feet (thick-thin) that allows proper positioning.
Important: When positioning the e-box on the helmet, the wiring connector must not stick out from
the edge of the helmet or be twisted (fig. 11 and 12).
Fig. 11 Fig. 12
Fig. 13
Insert the wiring connector all the way inside the
e-box, making sure that it is pointing in the right
direction: the letter “n” must be visible (as
shown in the figure).
EN
10
Position the "safety block" on the wiring, then secure it in the e-box housing (Fig. 14-15-16).
Fig. 14 Fig. 15 Fig. 16
Remove the protective film from the feet and apply the system to the helmet (Fig. 17-18);
Important: If the position is less than perfect, remove the foot from the helmet immediately and try
again.
Fig. 17 Fig. 18
NB: It will take up to 24 hours for the adhesive to stick completely. During this time, do not expose
the helmet to atmospheric agents. During the first 12 hours, do not remove the e-box from the
feet.
Caution: Once the adhesive is applied, it cannot be reused in a different position and will have to be
replaced once removed.
M5
11
3.3. Positioning the Bluetooth keypad
Fig. 19
The Bluetooth wireless keypad can be
positioned as desired, provided it is within a 5meter radius from the e-box.
The recommended position is the left side of the
helmet, so that it can be easily used with the left
hand.
Thoroughly clean the surface of the helmet where the keypad will be applied;
Find the best spot where to position the keypad, making sure that the surface of the base sticks
perfectly to the shell.
Remove the protective film and apply the keypad to the helmet;
Important: If the position is less than perfect, remove the foot from the helmet immediately and
try again.
NB: It will take up to 24 hours for the adhesive to stick completely. During this time, do not expose
the helmet to atmospheric agents.
Caution: Once the adhesive is applied, it cannot be reused in a different position and will have to be
replaced once removed.
3.4. Operating of the Bluetooth keyboard
The Bluetooth keyboard comes already paired up with the system, so it is immediately operational.
In case you replace the original keypad with a new one, the new keypad will have to be paired up:
put the system in Setting Mode
press the “n” key and the “
on
” key at the same time
A voice message inside the helmet confirms that the pairing up was successful.
4. FUNCTION KEYS
“BACK” BUTTON
“▲” BUTTON
“▼”
BUTTON
“N” BUTTON
“
on
” BUTTON
EN
12
5. BASIC FUNCTIONS
System ON
Briefly press “BACK”, until the LEDs turn on and you hear a beep in the
headset.
System OFF
Press “BACK” and keep it pressed for about 2 seconds, until the LEDs
turn off and you hear a beep in the headset.
Increase Volume
Briefly press “” to increase the volume. A double tone signals the
highest volume level.
Decrease Volume
Briefly press “” to decrease the volume. A double tone signals the
lowest volume level.
5.1. Auto On / Off Function
The system does not have to be turned on and off every time you use the motorcycle: thanks to the
triaxial accelerometer, if the helmet does no move for more than 30 seconds, the M5 system goes
into “deep sleep” mode. The system is completely turned on as soon as movement is detected.
If the system is in “deep sleep” mode for more than 7 days, it turns off completely. To turn it back on,
the “on” key need to be pressed.
5.2. N-Com Wizard and N-Com App
“N-Com Wizard” is the PC application that can be used to manage and configure the M5
system.
The program can be downloaded from the Internet site www.n-com.it, in the “Download”
section. In order to use it, a helmet equipped with M5 must be connected to the PC,
using the USB cable supplied with the system.
The functions that can also be managed from the N-Com Wizard are listed here below
with the specific icon.
The N-Com system is preset to be hooked up to the “N-Com App”, the application
compatible with Android, iPhone and iPad that can be used to configure and operate the
N-Com system directly from a Smartphone.
With the N-Com App, you can carry out most of the functions included in the N-Com
Wizard program or, alternatively, it can be used as a wireless Bluetooth keypad.
The N-Com APP can be downloaded free of charge from Google Play or Apple Store.
For additional details, please visit the website www.n-com.it
The functions that can also be managed from the N-Com Wizard are listed here below
with the specific icon.
5.3. Pairing up with Bluetooth devices
Make sure the M5 is turned off;
Put the system in setting mode: press the “BACK” key and keep it pressed for 4 seconds,
until the red LED starts to flash quickly;
Turn on the search for Bluetooth devices (smartphone, GPS, MP3 reader) on the device;
Select the N-Com device. If a password is requested, enter 0000 (four zeros);
Connection between the two devices is established after a few seconds.
Note: The affiliation is stored in the helmet and in the cell phone and it is not lost when the two
devices are turned off. As a result it needs to be carried out only once.
M5
13
Automatic Connection
Once the Bluetooth device has been paired up, connection is automatic
when the system is turned on.
Manual Connection
In case connection is not automatically initiated after a few seconds, you
can connect from the Bluetooth device or by pressing “
on
” and keep it
pressed for about 2 seconds.
6. MOBILE PHONE
Answering a phone call
Briefly press any key when you hear the incoming call signal.
Voice call Press “
on
” and keep it pressed for about 2 seconds.
Redial last number Press “
on
” and “n” at the same time.
Dial Friend Number Press “n” and keep it pressed for about 2 seconds.
Hanging up/rejecting a
phone call
Press “
on
” and keep it pressed for about 2 seconds.
Transferring a call from
helmet to mobile phone
To transfer an ongoing call from the helmet to the mobile phone, press
both “
on
” and “n” at the same time and keep them pressed for 2
seconds.
Manual phone
connection
Press “
on
” and keep it pressed for about 2 seconds.
Manual phone
disconnection
Press “” and keep it pressed for about 4 seconds.
Conference call function
When a call comes in on a mobile phone connected via Bluetooth to M5, the Rider-Pillion Passenger
intercom is temporarily turned off. However, if you wish to share the phone call with the other helmet,
simply turn on the intercom manually during the phone call.
Turning on the phone conference call
function
During the phone call, briefly press “n”.
Turning off the phone conference call
function
During the phone call, briefly press “n”.
N.B.: The Phone Conference Call function can only be used with a Rider-Pillion Passenger intercom
(channel 1) and not with Bike-to-Bike communication (channels 2-6).
6.1. Friend Number
When you use the N-Com Wizard or the N-Com App, you can choose a “Friend
Number”, which you can be call by pressing a speed-dial button.
Calling the Friend
Number
Press the “n” key and keep it pressed for 2 second.
EN
14
6.2. Managing two mobile phones (or Bluetooth devices)
The M5 system can be hooked up to two phones (or Bluetooth) devices at the same time.
The second phone (secondary device) can receive calls but not make them.
To pair up the second Bluetooth phone (secondary device):
Make sure the M5 is turned off;
press the “BACK” key and keep it pressed for 4 seconds, until the red LED starts to flash
quickly (setting mode);
Press the “
on
” key and keep it pressed for about 2 seconds.
Turn on the search for Bluetooth devices (smartphone, GPS, MP3 reader) on the device;
Select the N-Com system from the list
7. MUSIC VIA BLUETOOTH – A2DP BLUETOOTH PROTOCOL
Play music (Play) Briefly press “
on
”.
Pause function (Pause)
When the player is connected and playing music, briefly press
“
on
”.
Next track (Skip) When the player is playing music, press “” for 2 about seconds.
Previous track (Rew) When the player is playing music, press “” for 2 about seconds.
Turning off the A2DP Press “
on
” and keep it pressed for about 4 seconds.
Turning on the A2DP
The A2DP is already active when the system is turned on;
otherwise, press the “
on
” key briefly.
You can also configure these settings through Smartphone Android, iPhone and iPad
thanks to the dedicated N-Com App.
8. MUSIC VIA CABLE
Connect the mini USB connector of the Multimedia Wire (not included) to the helmet and the other
end to the audio device. A colored band on the cable indicates the connector to be hooked up to the
audio device.
Turning on the cable audio Press the “
on
” key three times.
Turning off the cable audio Press the “
on
” key three times.
M5
15
9. SATELLITE NAVIGATOR FOR MOTORCYCLES
M5 system is compatible with the most common satellite navigators for motorcycles. For a list of
compatible models and additional details, visit the website www.n-com.it
To pair up a satellite navigator to the M5 system, follow the same procedure illustrated in Chapter 5.3.
GPS Conference Call Function
The Conference function allows you to keep the “Rider-Pillion Passenger” intercom open even while
the satellite navigator is giving instructions, thus preventing the intercom mode to be turned off every
time the navigator gives instructions. However, if you wish to activate the Conference GPS function,
simply turn on the intercom manually during the GPS directions.
Turning on the GPS Conference
function
During the GPS directions, briefly press “n”.
Turning off the GPS Conference
function
During the GPS directions, briefly press “n”.
At the end of the GPS communication, the intercom with the second helmet stays open and the
"Conference" setting is stored for future GPS communications.
N.B.: The GPS Conference function can only be used with the Rider-Pillion Passenger intercom
(channel 1) and not with the Bike-to-Bike communication (channels 2-6).
9.1. Navigators on Smartphone (Smart Navi System)
By connecting the M5 system to a Smartphone, all navigator instructions are sent to the helmet
through the A2DP profile. During each navigator communication, the intercom via Bluetooth is
automatically cut off and subsequently restored when the navigator has stopped giving road
instructions (SMART NAVI SYSTEM function).
The Smart Navi System function can be turned off in Setting Mode (see Chapter 14).
10. FM RADIO
Turning on the radio Press the “
on
” key twice
Turning off the radio Press the “
on
” key twice.
New station automatic search Press “” and keep it pressed for 2 seconds.
Pre-setting a radio station (max.
6 stations)
Press “” and keep it pressed for 4 seconds.
Changing radio stations (among
the pre-set ones)
Press “” and keep it pressed for 2 seconds.
This function can also be turned on through PC using the “N-Com Wizard”
program or through Smartphone Android, iPhone and iPad thanks to the
dedicated N-Com App.
EN
16
11. EMERGENCY STOP SIGNAL (ESS)
The M5 system is equipped with a LED system to assist emergency braking. In case of sudden
braking, the LEDs on the M5 flash for a few seconds.
The braking level can be adjusted through a PC (N-Com Wizard) or Smartphone
Android, iPhone and iPad thanks to the dedicated N-Com App.
Turning on/off the Emergency Stop
Signal (ESS)
Press the BACK key briefly
OR
Press the “” and “” keys and keep them pressed for about
2 seconds.
N.B.: We recommend turning off the Emergency Stop Signal on the Rider’s helmet in case a Pillion
Passenger is riding on the back.
12. RIDER-PASSENGER INTERCOM
12.1. Rider-Passenger intercom pairing up
Make sure the M5 is turned off;
Put both systems in Setting mode (press the “BACK” key and keep it pressed for 4 seconds,
until the red LED starts to flash quickly);
Press the “n” key briefly on one of the systems (Channel 1 pairing up);
A “wait for connection” tone is emitted until the pair up procedure is not completed.
12.2. Rider-Passenger intercom function
After carrying out the proper pair up procedure, turn on the two helmets. To activate the intercom
connection, starting from an N-Com system that has already been turned on, briefly press key "n".
Manual intercom connection With M5 turned on, briefly press “n”.
Manual intercom
disconnection
With M5 turned on, briefly press “n”.
M5
17
13. BIKE-TO-BIKE INTERCOM
The N-Com system is used for bike-to-bike communication up to a distance of about 500 m (open
terrain, no obstacles). For proper operation of bike-to-bike communication, you need to open the
antennas of the e-box M5, as shown in the figure.
Fig. 20 Fig. 21
The M5 system entails the use of a default “STANDARD” commands configuration, or the use of a
“FRIENDS” configuration that can be turned on from the N-Com Wizard or dedicated App.
The difference between the two configurations lies in the number of motorcycles that can be hooked
up: the STANDARD configurations allows up to 3 different motorcycles to be hooked up to the M5
system, while the FRIENDS configurations allows up to a total of 6.
Important: If you use the FRIENDS configuration, you need to visit the N-Com website and download
the dedicated commands diagram (section Download/Command Summary Diagram).
N.B.: The range and quality of the communication may vary significantly depending on the presence
of obstacles, weather conditions, magnetic fields.
N.B.: The range of the communication varies depending on the N-Com systems used.
13.1. Bike-to-Bike Intercom Affiliation (Standard configuration)
Make sure the M5 is turned off;
Put both systems A and B in Setting Mode (press the “BACK” key and keep it pressed for 4
seconds, until the red LED starts to flash quickly);
On system A, press the command related to the “setting position” where you wish to store
system B;
Pairing up CHANNEL 1 Briefly press “n”.
Pairing up CHANNEL 2 Press the “n” key twice.
Pairing up CHANNEL 3 Press the “n” key three times.
Pairing up CHANNEL 4 Briefly press “
on
”.
Pairing up CHANNEL 5 Press the “
on
” key twice.
Pairing up CHANNEL Press the “
on
” key three times.
N.B.: Channels 4-5-6 can be paired up and used only by activating the FRIENDS configuration.
EN
18
CHANNEL 1 is typically used for the Rider-Pillion Passenger connection, however it can also be used
for the Bike-to-Bike intercom.
The use of CHANNEL 1 is different from the other channels due to the following specific characteristics:
By pressing key "n", the intercom connection is automatically activated.
The Phone Conference function and the GPS Conference function can be used.
13.2. Bike-to-Bike intercom function
How the Bike-to-Bike call works (Standard Configuration)
Connection CHANNEL 1 Briefly press “n”.
Call CHANNEL 2 Press the “n” key twice.
Call CHANNEL 3 Press the “n” key three times.
Disconnection of active intercom Briefly press “n”.
With FRIENDS CONFIGURATION active:
Call CHANNEL 4 Briefly press “
on
”.
Call CHANNEL 5 Press the “
on
” key twice.
Call CHANNEL 6 Press the “
on
” key three times.
Disconnection of active intercom Briefly press “
on
”.
N.B.: In case the memory setting is empty, or the other helmet cannot be reached, an error tone will
sound in your helmet.
Taking a Bike–to-Bike call
Four calling tones will sound in the helmet receiving the Bike-to-Bike call (channel 2-6), and all open
audio functions will be temporarily cut off (including the Rider – Pillion Passenger intercom, if any).
Answering a Bike-to-Bike phone call Briefly press any key when you hear the incoming call signal.
In case you take the call, communication is automatically established.
In case the call is not answered, the system returns to the situation prior to receiving the call.
M5
19
14. SETTING MODE
All Bluetooth pair ups and other adjustments are carried out in this mode.
To put the system in Setting mode (system turned off), press the “BACK” key and keep it pressed for 4
seconds, until the red LED starts to flash quickly.
n
on
N
+
on
▲ ▼
▲
+
▼
BACK
Turning on/off the RDS x1
Turning on/off the Smart Navi System
2 sec
Pairing up Secondary Phone 2 sec
Pairing up CHANNEL 1 x1
Pairing up CHANNEL 2 x2
Pairing up CHANNEL 3 x3
Pairing up CHANNEL 4 X
Pairing up CHANNEL 5 x2
Pairing up CHANNEL 6 x3
Pairing up the wireless keypad 10 sec
Reset 4 sec
*With Friends Configuration active.
15. BATTERY AND RECHARGE
15.1. Low battery signal
During its operation, the system alerts the user with a voice message when the battery is low. From
the first message, the system has a 1-hour autonomy. Warning is given every 10 minute.
15.2. Charging the system
To charge the system, hook it up to the battery charger or to a USB outlet powered with the USB-mini
USB cable supplied as standard equipment. The charge will take place as follows:
Fig. 22
When you connect the M5 system to the
battery charger, the red LED of the
Emergency Stop Light stars to flash (at a
frequency of 10 seconds).
When the battery is fully charged, the red
LED turns off.
N.B.: If the device has not been charged for a long time (a few months), it may not be possible to turn
on the system during the first few minutes of the charging, as the voltage may drop below the
minimum limit.
EN
20
16. SUMMARY TABLE OF CONTROLS – STANDARD CONFIGURATION
Button
n
on
N
+
on
+
BACK
Turning on X
Turning off 2 sec
Increase Volume X
Decrease Volume X
Basic Functions
Turning on/off the
Emergency Stop Signal
X
Answer phone call X X X X
Voice call 2 sec
Redial last number X
Dial Friend Number 2 sec
Hang up/reject a phone
call
2 sec
Call transfer 2 sec
Manual Device
Connection
2 sec
Manual Device
Disconnection
4 sec
Turning on the
Conference function
X
Bluetooth Devices
Turning off the
Conference function
X
Connection CHANNEL 1 X
Disconnection of active
intercom
X
Calling CHANNEL 2 x2
Calling CHANNEL 3 x3
Calling CHANNEL 4**
X
Calling CHANNEL 5**
x2
Intercom
Calling CHANNEL 6**
x3
M5
21
Button
n
on
N
+
on
+
BACK
Turning on the Radio x2
Turning off the Radio x2
Automatic search for
new station
2 sec
Change station
(pre-set stations)
2 sec
Radio Menu
Pre-set station 4 sec
Play music (Play) X
Pause Function (Pause) X
Next track (Forward) 2 sec
Previous track (REW) 2 sec
Enable A2DP profile X
Disable A2DP profile 4 sec
Activate audio via cable x3
Bluetooth Music / Cable
Deactivate audio via
cable
x3
Pairing up mode (system
turned off)
4 sec
Turning on/off the RDS X
Turning on/off the Smart
Navi System
2 sec
Pairing up secondary
mobile phone (or device)
2 sec
Pairing up CHANNEL 1 X
Pairing up CHANNEL 2 x2
Pairing up CHANNEL 3 x3
Pairing up CHANNEL 4** X
Pairing up CHANNEL 5** x2
Pairing up CHANNEL 6** x3
Pairing up the wireless
keypad
10 sec
Setting*
Reset 4 sec
* All the Setting functions must be carried with the system in Setting Mode.
**With Friends Configuration active.
EN
22
17. LIMITED WARRANTY
With this LIMITED WARRANTY CERTIFICATE, Nolangroup warrants this Product to be free from defects in material
and workmanship at the time of its original purchase by the buyer. We invite you to:
- Read the cautions pertaining to safety and proper use.
- Read the warranty terms and conditions.
- Keep the originals sales receipt. This must be shown in case of repairs covered by warranty. In these cases, the
product has to be taken back to the dealer where it was purchased.
17.1. Warranty coverage
If any defect covered by this limited warranty certificate is discovered within 2 (two) years from the purchase date
shown on the tax receipt, Nolangroup shall repair or replace the defective product through its distribution network
after having verified the defect. Nolangroup shall supply all the material and labor that is reasonably required to
remedy the defect, except in those cases where the damage is caused by one of the items listed in the following
paragraph “Exclusions and limitations of the Coverage”.
17.2. Exclusions and limitations of the coverage
This warranty only covers defects in materials and manufacturing. Nolangroup shall not be considered responsible
for product defects that can be attributed, either partially or in full, to any other cause, including but not limited to:
Defects or damages resulting from using the Product in conditions that differ from the usual ones.
Damages caused by improper use not conforming with normal operation in accordance with the product
operating and maintenance instructions provided by Nolangroup.
Negligence and normal wear of internal and external parts.
Any damage caused by an accident;
Any change or modification made to the helmet or to the N-Com system by the user or by third parties.
Color changes or damages caused by exposure to harmful chemical products.
The use of incompatible accessories that are not part of the N-Com product range.
Moreover, the warranty does not cover product defects caused by fortuitous events, modifications or
adjustments, causes of
force majeure
or damages deriving from the product coming in contact with liquids.
The internal helmet components are not and cannot be waterproof. Consequently, any improper exposure to
rain, humidity, food spillages or other liquids can result in damages to the N-Com electronic devices, damages
for which Nolangroup shall not be responsible.
This warranty does not include those parts subject to wear and tear such as, for example, the rechargeable
battery and the cables used for connection between the various N-Com systems or between the N-Com
systems and other devices.
Since Nolangroup does not supply the system on which the cell phones work, it shall not be responsible for
the operation, availability, coverage, services or range pertaining to the aforementioned system.
Whenever the product is used in conjunction with accessories or equipment not supplied by Nolangroup,
Nolangroup shall not guarantee proper operation of the product/device combination, nor will it accept
requests for repairs or replacements under warranty in case the product is used in such a way.
Nolangroup shall not be responsible in case the product presents limited capabilities due to the operating mode of
cell phones or of other accessories or equipment not supplied by Nolangroup.
Tampering with the internal electronic card or with other parts of the N-Com system shall invalidate the warranty.
Moreover, the defects covered by this warranty do not include all those specific and subjective situations that may
come up during the active use of the helmet such as, for example, comfort problems while riding or aerodynamic
noises.
Nolangroup shall not be held responsible in any case for incidental or consequential damages (including, without
any limitation whatsoever, damages to one or more persons) resulting from non-fulfillment of the obligations
arising from this warranty as it pertains to Nolangroup products.
17.3. Validity of this limited warranty
This warranty is valid only if the enclosed warranty form is duly and completely filled out with the following
information:
Product identification code
Name and stamp of the authorized dealer.
M5
23
Product purchase date.
Buyer’s name and address.
Nolangroup reserves itself the right to not carry out repairs under warranty if the aforementioned information is
removed or modified after the original purchase of the product from the dealer.
17.4. Procedure for the forwarding of claims
To forward a claim covered by this warranty, the buyer has to directly notify the dealer where the helmet was
purchased with regards to the defect, presenting at the same time the defective product, a copy of the sales receipt
and the Warranty registration form, duly filled out as instructed above.
PRIOR TO CONTACTING THE DEALER, WE RECOMMEND THAT YOU READ CAREFULLY THE USER MANUAL
ENCLOSED WITH THE PRODUCT.
AFTER 2 (TWO) YEARS FROM THE DATE OF PURCHASE, THIS LIMITED WARRANTY IS VOID FOR ALL EFFECTS AND
PURPOSES.
Repairs or maintenance under warranty do not extend the period of the warranty itself. Therefore, in case the
product or one of its components is replaced, this does not initiate a new warranty period, as the purchase date of
the original product shall be taken into account for warranty purposes.
Only for repairs or replacement of electronic components, in the event that Nolangroup proceeds to repairing or
replacing the product, said product shall enjoy a warranty period equal to the residual portion of the original
warranty or ninety (90) days from the repair date (the longer period being considered).
The repair or replacement can be carried out even with regenerated components with equivalent functions.
The replaced parts or components shall become property of Nolangroup.
THIS WARRANTY VOIDS AND REPLACES ANY OTHER WRITTEN OR VERBAL WARRANTIES PROVIDED FOR BY THE
LAW THAT CAN BE DEROGATED AT THE PARTIES’ WILL; SPECIFICALLY, NOLANGROUP DOES NOT GRANT SPECIFIC
WARRANTS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO CASE SHALL NOLAN BE
LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES INCLUDING BUT NOT LIMITED TO LOST PROFITS OR
COMMERCIAL DAMAGES, TO THE FULL EXTENT THOSE DAMAGES CAN BE DISCLAIMED BY THE LAW.
NOLANGROUP RESERVES ITSELF THE RIGHT TO MODIFY, AT ANY TIME AND WITHOUT ADVANCE NOTICE, THE
PRODUCT CHARACTERISTICS, FUNCTIONS, COMPATIBILITY AND SOFTWARE.
Some Countries do not allow the exclusion or limitation of incidental or consequential damages, or the limitation of
the duration of implied warranties; as a result of this, the previous limitations and exclusions may not be applicable
to you.
This warranty does not have any effect on the customer’s legal rights under the national jurisdiction in force or on
the consumer’s rights towards the dealer sanctioned by the purchase/sale contract.
This warranty is valid throughout the European territory, and it represents the only express warranty provided by
Nolangroup in relation to the sale of its own products. This warranty does not affect the rights to which the buyer is
entitled and which are expressly provided for by Directive 1999/44/CE.
This warranty does not affect the consumer’s rights provided for by the law, and specifically by the provisions of
Legislative Decree 2 February 2002 n. 24.
17.5. Product identification
N-Com products are identified by means of a code that allows product
traceability and identification.
The identification code is listed on the Bluetooth M5 control unit and on
the outside of the sales package.
18. WARRANTY REGISTRATION FORM
Product name: M5
Identification code
Buyer’s Information
Name
Last name
Address
Phone
e-mail
Dealer’s stamp
Date of purchase
FOR USA AND CANADA MARKET ONLY -
SPECIAL WARNING
------------------------------------------------------------------------
POUR LE MARCHE US ET CANADIEN UNIQUEMENT -
MISE EN GARDE SPECIALE
------------------------------------------------------------------------
SÓLO PARA EL MERCADO USA Y CANADÁ -
ADVERTENCIAS IMPORTANTES
EN
2
FOR USA AND CANADA MARKET ONLY: SPECIAL WARNING
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device
may not cause harmful interference, and (2) this device must accept any interference received,, including interference that
may cause undesired operation of the device.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority
to operate the equipment.
NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this
equipment. Such modifications could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the
FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
This model meets the government’s requirements for exposure to radio waves. Your wireless device is a radio transmitter
and receiver. It is designed and manufactured not to exceed limits for exposure to radio frequency (RF) energy set by the
Federal Communications Commission (FCC) of the U.S. Government and by the Canadian regulatory authorities.
The exposure standard for wireless mobile devices employs a unit of measurement known as the Specific Absorption
Rate, or SAR. The SAR limit set by the FCC and by the Canadian regulatory authorities is 1.6 W/kg.1.
For Canada market only: This EUT is compliant with SAR for general population/uncontrolled exposure limits in IC RSS-
247. The M5 electronic device is positioned on a minimum distance of 30 mm from the head of the user, therefore no
SAR test have been conducted on the product.
Model: M5 FccID: Y6MNCOM9 IC: 9455A-NCOM9
R-NZ
Model:WRC FccID: Y6MNCOM11 IC: 9455A-NCOM11
R-NZ
Bluetooth is a registered trademark property of Bluetooth SIG, Inc.
FOR USA AND CANADA MARKET ONLY: LIMITED WARRANTY
Limited warranty certificate valid for 2 (two) years from the date of purchase.
Dear Customer,
Thank you for choosing a Nolangroup N-Com device.
PLEASE READ CAREFULLY ALL THE CLAUSES AND CONDITIONS OF THIS LIMITED WARRANTY CERTIFICATE.
By this LIMITED WARRANTY CERTIFICATE, Nolangroup guarantee to the original purchaser of the N-Com that the product
is free from all material and manufacturing defects at the time of purchase.
COVER PROVIDED BY THE WARRANTY
If any defect covered by this limited warranty certificate comes to light within 2 (two) years from the date of purchase,
Nolangroup shall proceed, through their distribution networks and after verifying the defect, to repair or replace the
defective product. Nolangroup shall supply all the materials and provide all the labor reasonably necessary to remedy the
reported defect, except for cases in which the damage is attributable to one of the reasons listed in the paragraph below,
entitled “Exclusions and limitations of cover”.
EXCLUSIONS AND LIMITATIONS OF COVER
This warranty covers only material and manufacturing defects. Nolangroup cannot be held liable for damages to the
product which are either wholly or partially attributable to any other cause, including, but not limited to:
a) damage caused by improper use, lack of due care, normal wear and tear of internal and external components;
b) scratches, abrasions, or other damage caused to the external parts of the N-Com by accidental impacts;
c) damage caused by the application of stickers and/or adhesives;
d) any damage caused by an accident;
EN
3
e) any modification or change made to the device by the user or by third parties;
fl) use of incompatible accessories not sold by Nolangroup.
Defects covered by this warranty likewise do not include all the specific and subjective situations which may arise during
dynamic use of the N-Com equipped helmet, such as problems of comfort due to improper sizing, or wind noise while
riding. Nolangroup cannot in any case be held liable for accidental or consequential damage (including, with no limitation
whatsoever, injuries to a person or persons) resulting from the failure to comply with the obligations stipulated in this
warranty regarding Nolangroup products.
Some states do not allow the exclusion or limitation of implied warranties, incidental or consequential damages, so the
above limitations and exclusions may not apply to you. This warranty gives you specific legal rights, and you may also
have other rights which vary from state to state
VALIDITY OF THIS LIMITED WARRANTY
This warranty is valid only if all the sections of the attached REGISTRATION FORM are completed in full and the
registration is returned to the address indicated on the card within 10 (ten) days from the date of purchase:
1) Identification code;
2) Name of the authorized dealer;
3) Date of purchase of the N-Com;
4) Name, address and telephone number of the purchaser.
PROCEDURE TO BE FOLLOWED TO MAKE POSSIBLE CLAIMS
To proceed with any claim covered by this warranty, the purchaser must notify directly Nolangroup’s agent in the USA of
the alleged defect encountered by him. In agreement with Nolangroup’s agent, the purchaser may have to return the
device to which complains refer, at the purchaser’s expense, along with the sales receipt or other proof of purchase (and
date of purchase) and a copy of the warranty registration form.
BEFORE REFERRING THE MATTER TO THE AGENT, WE ADVISE YOU TO READ CAREFULLY THE USER’ MANUAL INCLUDED
WITH THE DEVICE WHICH MUST BE FOLLOWED SCRUPULOUSLY FOR YOUR OWN PROTECTION AND THAT OF THIRD
PARTIES.
2 (TWO) YEARS AFTER THE DATE OF PURCHASE THIS LIMITED WARRANTY SHALL LAPSE ENTIRELY.
This warranty is valid in the entire territory of the United States and Canada is the only express warranty given by
Nolangroup in relation to the sales of their own devices.
Any service provided under the warranty does not have the effect of extending the warranty period itself. If any device or
any of its components are replaced a new warranty period does not begin to run on the product or on individual
components supplied by the way of replacement; the date of purchase of the original device remains the deciding factor.
For further information, please contact the following address or telephone numbers:
USA
CIMA INTERNATIONAL
1585 Beverly court #118
Aurora IL 60502
Ph: (630) 701-1601
Fax: (630) 701-1606
E-mail: info@cimaint.com
Toll-free (USA only): 866-243-5638
CANADA
CLARY SPORTS LOISIRS
67 ROUTE 329
ST DONAT (QC) J0T 2C0 – CANADA
Ph: 001 8194244545
Fax: 001 819 424 7859
E-mail: clary@st-donat.net
FR
4
POUR LE MARCHE US et CANADIEN UNIQUEMENT: MISE EN GARDE SPECIALE
Cet appareil est conforme à la section 15 de la réglementation FCC. Son fonctionnement est soumis aux deux conditions
suivantes : (1) Cet appareil ne doit pas créer d’interférences nuisibles, et (2) cet appareil doit accepter les interférences
reçues, y compris les interférences pouvant provoquer des dysfonctionnements de l’appareil.
Les changements ou modifications non expressément approuvés par les autorités compétentes en matière de conformité
peuvent priver l'utilisateur du droit d'utiliser l'équipement en question.
REMARQUE : Le fabriquant n’est pas responsable de l’interférence radio ou TV causée par les modifications apportées à cet
équipement sans autorisation préalable. De telles modifications pourraient annuler l’autorisation de l’utilisateur de faire
fonctionner cet équipement.
A l’issue des tests dont il a fait l’objet, ce produit est conforme à la section 15 de la réglementation FCC applicable aux
appareils numériques de classe B. Ces limites sont conçues pour fournir une protection suffisante contre les interférences
nuisibles dans les installations résidentielles.
Cet équipement génère, utilise et peut émettre des ondes radioélectriques susceptibles de créer des interférences nuisibles
dans les communications radioélectriques si l'équipement est installé incorrectement. Cependant, il n'est pas garanti
qu'aucune interférence ne se produise dans une installation particulière.
Dans le cas où cet équipement créerait des interférences avec la réception radio ou télévisée, ce qui peut être vérifié en
éteignant et en rallumant l'appareil, il est conseillé d'essayer de corriger ces interférences en appliquant une ou plusieurs
des mesures suivantes :
Réorienter ou déplacer l'antenne de réception.
Augmenter la distance entre l'équipement et les équipements.
Relier l'équipement à une prise de courant différente de celle du récepteur.
Prendre conseil auprès d'un distributeur ou d'un technicien radio/TV qualifié.
Ce modèle répond aux exigences gouvernementales en matière d'exposition aux ondes radio. Votre appareil est un
émetteur-récepteur radio. Il est conçu et fabriqué pour ne pas dépasser les limites d'exposition aux radiofréquences (RF)
définies par la Federal Communications Commission (FCC) du gouvernement des États-Unis et par les autorités
réglementaires canadiennes.
La norme d'exposition pour les appareils mobiles utilise une unité de mesure appelée Débit d'Absorption Spécifique, ou
SAR. La limite de DAS fixée par la FCC et par les autorités réglementaires canadiennes est de 1,6 W/kg.1.
Uniquement pour le marché canadien : Ce EUT (test pour l’utilisation de l’équipement) est conforme au DAS relativement à
l’utilisation par le grand public /aux limites d’intensité pour un environnement non contrôlé contenus dans la norme IC
RSS-247. L’électronique du M5 est positionné à une distance minimum de 30mm de la tête de l’utilisateur, donc, aucun test
DAS n’a été effectué sur le produit.
Model: M5 FccID: Y6MNCOM9 IC: 9455A-NCOM9
R-NZ
Model:WRC FccID: Y6MNCOM11 IC: 9455A-NCOM11
R-NZ
Bluetooth est une marque déposée de Bluetooth SIG, Inc.
POUR LE MARCHE US ET CANADIEN UNIQUEMENT: GARANTIE LIMITEE
Certificat de garantie limitee 2 (deux) ans, a compter de la date d’achat.
Cher Client, Merci d’avoir choisi un appareil Nolangroup N-Com.
VEUILLER LIRE SOIGNEUSEMENT L’ENSEMBLE DES CLAUSES ET DES CONDITIONS DE CE CERTIFICAT DE GARANTIE
LIMITEE. Par le présent CERTIFICAT DE GARANTIE LIMITEE, Nolangroup assure à l’acheteur initial du N-Com que le produit
ne présente au moment de l’achat, aucun défaut quant aux matériaux utilisés ou à la fabrication.
COUVERTURE DE LA GARANTIE
Si un quelconque défaut couvert par le présent certificat de garantie limitée est découvert d’ici 2 (deux) ans, à compter de
la date d’achat, Nolangroup s’engage par le biais de ses réseaux de distribution et après avoir vérifié la nature du défaut, à
réparer ou a remplacer le produit défectueux. Nolangroup fournira tout le matériel et le travail raisonnablement requis
pour réparer le défaut signalé, sauf si le dommage est dû à l’une des raisons indiquées au paragraphe suivant, intitulé
« Exclusions et limites de la couverture ».
FR
5
EXCLUSIONS ET LIMITES DE LA COUVERTURE
Cette garantie couvre uniquement les défauts des matériaux et de fabrication. Nolangroup ne saurait être tenue pour
responsable des défauts du produit, imputables, en tout ou en partie, à une des causes reportée dans la liste – non
exhaustive – ci-après :
a) Dommages dûs à un usage incorrect, manque d’entretien, usure normale des parties internes et externes.
b) Rayures, abrasions, ou tout autre dommage causé aux parties externes du N-Com par des impacts accidentels.
c) Dommages causés par l’installation d’adhésifs.
d) Dommages dûs à un accident.
e) Modifications ou changements apportés à l’appareil par l’utilisateur ou des tiers ;
f) Utilisation d’accessoires incompatibles non vendus par Nolangroup.
La garantie ne couvre pas les défauts liés à toutes les situations particulières qui pourrait se présenter pendant l’utilisation
dynamique du casque équipé N-Com, tels que des problèmes de confort dûs à la taille inappropriée, ou au bruissement du
vent au cours du pilotage.
Nolangroup ne pourra en aucun cas être tenu pour responsable des dommages accidentels ou conséquentiels (y compris,
sans limitation aucune, les lésions corporelles provoqués aux personnes) dûs au non respect des obligations dérivant de
cette garantie concernant les produits Nolangroup.
Certains Pays ne permettent pas l’exclusion ou la restriction des garanties implicites, des dommages accidentels ou
conséquentiels, par conséquent les restrictions ou les exclusions précédentes pourraient ne pas être applicables. Cette
présente garantie vous confère des droits juridiques spécifiques, et vous pouvez également jouir d’autres droits qui
peuvent varier d’une juridiction à une autre.
VALIDITE DE CETTE GARANTIE LIMITEE
Cette garantie n’est valable que si toutes les sections de la fiche d’enregistrement ci-jointe sont remplies dans leur totalité
et que l’enregistrement est retourné à l’adresse indiquée sur la carte dans les 10 (dix) jours à partir de la date d’achat :
1) Code d'identification ;
2) Nom du revendeur agréé ;
3) Date d’achat du N-Com ;
4) Nom, adresse et numéro de téléphone de l’acheteur.
PROCEDURE POUR L’ENVOI DES RECLAMATIONS EVENTUELLES
Pour toute réclamation couverte par la présente garantie, l’acheteur devra communiquer directement au revendeur de
Nolangroup aux Etats-Unis le défaut présumé constaté. En accord avec le revendeur de Nolangroup, l’acheteur peut avoir
à retourner l’appareil dont la plainte se réfère, aux frais de l’acheteur, accompagné du reçu de caisse ou autre preuve
d’achat (et date d’achat) et d’une copie de la fiche d’enregistrement.
AVANT DE VOUS ADRESSER A VOTRE REVENDEUR, NOUS VOUS RECOMMANDONS DE LIRE ATTENTIVEMENT LES
INSTRUCTIONS D’UTILISATION FOURNIES AVEC L’APPAREIL QUI DOIVENT ETRE SCRUPULEUSEMENT SUIVIES POUR
VOTRE PROTECTION ET CELLES DES TIERS.
LA GARANTIE EXPIRE ENTIEREMENT 2 (DEUX) ANS APRES LA DATE D’ACHAT.
La présente garantie est valable sur l’ensemble du territoire des Etats-Unis et du Canada est constitue la seule garantie
expresse fournie par Nolangroup concernant les ventes de ses appareils.
Les interventions au titre de la garantie ne sauraient avoir pour effet de prolonger la durée de celle-ci. Par conséquent, en
cas de remplacement d’un appareil ou de l’un de ses composants, ledit appareil ou ledit composant fourni en
remplacement ne déclenchera pas une nouvelle période de garantie sur le produit et il faudra au contraire tenir compte de
la date d’achat de l’appareil d’origine.
Pour plus d’informations, contacter les adresses ou numéros de téléphone suivants :
POUR ETATS
-
UNIS
: CIMA INTERNATIONAL
1585 Beverly court #118 - Aurora IL 60502
Tél : (630) 701-1601 Fax : (630) 701-1606
E-mail : info@cimaint.com
Numéro vert (Etats-Unis uniquement) : 866-243-5638
POUR LE CANADA
: CLARY SPORTS LOISIRS
67 ROUTE 329
ST DONAT (QC) J0T 2C0 –CANADA
Tél : 001 8194244545 Fax : 001 819 424 7859
E-mail : clary@st-donat.net
ES
6
SÓLO PARA EL MERCADO USA y CANADÁ: ADVERTENCIAS IMPORTANTES
Este dispositivo cumple con el apartado 15 de las normas FCC. El funcionamiento está sujeto a las dos condiciones
siguientes: (1) Este dispositivo no debe ocasionar interferencias dañinas, y (2) este dispositivo debe poder soportar
cualquier interferencia recibida, incluidas las posibles interferencias que provoquen mal funcionamiento.
Cualquier cambio o modificación que no esté expresamente aprobado por la parte responsable podría anular el derecho
del usuario a manipular el equipo.
NOTAS: El fabricante no será responsable de cualquier interferencia radio o TV ocasionada por modificaciones no
aprobadas para este equipo. Dichas modificaciones podrían anular el derecho del usuario a utilizar el equipo.
Este producto ha sido probado y se ha determinado que cumple con los límites establecidos en el apartado 15 de las
normas FCC para un dispositivo digital de clase B. Estos límites se han diseñado para brindar un grado de protección
razonable contra las interferencias dañinas en una instalación de carácter residencial. Este equipo genera, utiliza y puede
irradiar energía de radiofrecuencia y, de no ser instalado y utilizado según las instrucciones, podría provocar
interferencias dañinas a comunicaciones de radio. No obstante, no existe ninguna garantía de que no se producirá
interferencia en una instalación específica.
Si este equipo causa interferencias dañinas a la recepión de radio o televisión, que se pueden detectar apagando y
encendiendo los equipos, el usuario puede intentar solucionar dichas interferencias con una o algunas de las siguientes
medidas:
Volver a orientar o colocar la antena de recepción
Aumentar la distancia entre el equipo o los dispositivos
Conectar el equipo a una toma de corriente que no sea la del receptor
Contactar al distribuidor o a un técnico radio /TV experto para asistencia técnica
Este modelo cumple con las exigencias del gobierno para la exposición a ondas de radio. Su dispositivo inalámbrico es un
transmisor y receptor de radio. Ha sido diseñado y fabricado para no exceder los límites de exposición a radiofrecuencia
(RF) establecidos por la Federal Communications Commission (FCC) del gobierno de EE.UU y por las autoridades
normativas de Canadá.
El estándar de exposición para dispositivos móviles inalámbricos utiliza una unidad de medición conocida como Tasa
Específica de Absorción o SAR. El límite de SAR establecido por la FCC y por los organismos reguladores de las
autoridades de Canadá es de 1,6 W/kg.1.
Sólo para el mercado en Canadá: Este EUT cumple con la SAR para la población general en cuanto a límites de exposición
sin control en IC RSS-247. El dispositivo electrónico M5 está situado a una distancia mínima de 30 mm de la cabeza del
usuario, por lo tanto, no han sido realizados ensayos SAR del producto.
Model: M5 FccID: Y6MNCOM9 IC: 9455A-NCOM9
R-NZ
Model:WRC FccID: Y6MNCOM11 IC: 9455A-NCOM11
R-NZ
Bluetooth es una marca registrada de propiedad de Bluetooth SIG, Inc.
SÓLO PARA EL MERCADO USA y CANADÁ: GARANTÍA LIMITADA
Garantía limitada - 2 (dos) años a partir de la fecha de compra.
Estimado consumidor, Le agradecemos por haber escogido un dispositivo Nolangroup N-Com.
POR FAVOR, LEA DETENIDAMENTE LAS CLÁUSULAS Y LAS CONDICIONES DEL PRESENTE CERTIFICADO DE GARANTÍA
LIMITADA.
Con el presente CERTIFICADO DE GARANTÍA LIMITADA, Nolangroup garantiza al comprador original del dispositivo NCom que el producto está libre de defectos por materiales y de fabricación en el momento de la compra del mismo.
COBERTURA PREVISTA POR LA GARANTÍA
Si se manifestara algún tipo de defecto cubierto por la presente garantía durante los 2 (dos) años a partir de la fecha de
compra, Nolangroup deberá, mediante las redes de distribución pertinentes y luego de haber constatado el defecto,
reparar o sustituir el producto defectuoso. Nolangroup suministrará todo el material y la mano de obra necesaria para
solucionar dicho defecto, a menos que la causa del daño sea atribuible a una de las excepciones mencionadas en el
párrafo siguiente : “Exclusiones y Limitaciones de la Cobertura”.
ES
7
EXCLUSIONES Y LIMITACIONES DE LA COBERTURA
La presente garantía cubre solamente los defectos por materiales o de fabricación. Nolangroup no será responsable por
defectos del producto atribuibles en todo o en parte alguna a cualquier otra causa, comprendida y no solo limitada a:
a) Defectos o daños causados por el uso incorrecto del producto, por descuido, por el deterioro o desgaste normal
del interior o exterior de sus componentes;
b) Arañazos, abrasiones, u otro daño ocasionado en las partes exteriores del N-Com como consecuencia de impactos
accidentales;
c) Daños ocasionados por la aplicación de etiquetas y/o adhesivos;
d) Cualquier daño ocasionado por un accidente;
e) Cualquier modificación o cambio aportados al dispositivo por parte del usuario o de terceros;
f) Uso de accesorios incompatibles y no vendidos por Nolangroup.
Los defectos cubiertos por la presente garantía no incluyen aquellas situaciones específicas y subjetivas que pudieran
ocurrir durante el uso dinámico del casco equipado con el sistema N-Com, por ejemplo los problemas causados por el
uso de una talla incorrecta, o por el ruido del viento durante la conducción. Nolangroup no podrá ser considerado
responsable por daños accidentales o consecuentes (incluyendo, sin limitaciones algunas, las lesiones a personas)
ocasionados por el incumplimiento de las obligaciones derivadas de la presente garantía hacia los productos Nolangroup.
Algunas naciones no aceptan la exclusión o la limitación de los daños accidentales o consecuentes, o la limitación de la
duración de la garantía implícita. Por lo tanto puede que las limitaciones y exclusiones anteriores no sean aplicables. La
presente garantía otorga al usuario derechos legales específicos, el usuario pudiera disponer de otros derechos aplicables
según la nación.
VALIDEZ DE LA PRESENTE GARANTÍA LIMITADA
La presente garantía es válida sólamente si se rellenan todas las partes de la TARJETA DE GARANTÍA adjunta y se envía a
la dirección indicada en la tarjeta dentro de los 10 (diez) días a partir de la fecha de compra:
1) Código de identificación;
2) Nombre del distribuidor autorizado ;
3) Fecha de compra del N-Com;
4) Nombre, dirección y número de teléfono del comprador.
PROCEDIMIENTO ANTE POSIBLES RECLAMACIONES
Para enviar cualquier tipo de reclamación cubierta por la garantía, el comprador debe informar directamente al vendedor
Nolangroup en USA del presunto defecto encontrado. De acuerdo con el vendedor Nolangroup, el comprador, a su
cargo, deberá devolver el dispositivo objeto de reclamación, junto con el recibo de compra u otra prueba de compra ( y
la fecha de compra) y una copia de la tarjeta de garantía.
ANTES DE DIRIGIRSE AL VENDEDOR, RECOMENDAMOS QUE EL USUARIO LEA DETENIDAMENTE EL MANUAL DE
INSTRUCCIONES DEL DISPOSITIVO Y LO CUMPLA ESTRICTAMENTE PARA SU PROPIA PROTECCIÓN Y PARA EL BIEN DE
TERCEROS. PASADOS 2 (DOS) AÑOS DESPUÉS DE LA FECHA DE COMPRA, LA PRESENTE GARANTÍA PERDERÁ SU
VALIDEZ A TODOS LOS EFECTOS.
La presente garantía tiene validez en todo el territorio de los Estados Unidos y de Canadá y es la única garantía otorgada
por Nolangroup en relación a la venta de sus dispositivos.
Cualquier reparación o sustitución durante la garantía no extenderá el plazo de validez de la misma. Por lo tanto, en caso
de sustitución del producto o de uno de sus componentes, no tendrá efecto un nuevo período de garantía para el
producto ni para el componente suministrado en sustitución, sino que será válida la fecha de compra del producto
original para indicar el plazo de garantía.
Para más información, por favor contáctenos a la siguiente dirección o a los números telefónicos a continuación:
POUR ETATS
-
UNIS
: CIMA INTERNATIONAL
1585 Beverly court #118 - Aurora IL 60502
Tél : (630) 701-1601 Fax : (630) 701-1606
E-mail : info@cimaint.com
Numéro vert (Etats-Unis uniquement) : 866-243-5638
POUR LE CANADA
: CLARY SPORTS LOISIRS
67 ROUTE 329 - ST DONAT (QC) J0T 2C0 –CANADA
Tél : 001 8194244545
Fax : 001 819 424 7859
E-mail : clary@st-donat.net
REGISTRATION FORM /
FICHE D’ENREGISTREMENT DE LA GARANTIE
/ TARJETA DE REGISTRO DE LA GARANTÍA
DEVICE INFORMATION / INFORMATION DU PRODUIT / DATOS DEL PRODUCTO
Serial Number (as printed on the box)
Numéro de série (situé à l’arrière de la boîte)
Número de serie (en la parte trasera del Box)
Designation of the model
Nom du produit
Denominación del producto
DEALER INFORMATION / COORDONNÉES DU REVENDEUR /
DATOS DEL DISTRIBUIDOR
Name of the au
thorized dealer
Nom du revendeur agréé
Nombre del distribuidor autorizado
Address
/ Adresse
/ Dirección
PURCHASE INFORMATION / INFORMATIONS D’ACHAT /
DATOS DE COMPRA
Date of purchase of the device
/ Date d’achat du N
-
Com /
Fecha de compra del produ
cto
PURCHASER INFORMATION / COORDONNÉES DE L’ACHETEUR /
DATOS DEL COMPRADOR
Name of the purchaser
Nom de l’acheteur
Nombre del comprador
Address
Adresse
Domicilio del comprador
Telephone Number
Numéro de téléphone
Número de telefono
E-mail ad
dress / E-
mail / E-
mail
OTHER INFORMATION / AUTRES INFORMATIONS /
OTRAS INFORMACIONES
How did you hear about this model of Nolangroup N
-
Com?
Comment avez-vous découvert ce modèle Nolangroup N-Com?
Como ha conocido este modelo de Nolangroup N-Com?
What do you mainly use your N
-
Com for (communication, music, phone, GPS,etc..)?
Quelle est votre principale utilisation du produit (communication, musique, téléphone, GPS, etc…)?
Como utiliza pricipalmente su sistema N-Com (comunicación, musica, movil, GPS)?
What brand and model of motorcycle do you ride? / Quelle marque et modèle de moto conduisez
-
vous? / Cual marca y modelo de moto
conduce?
What is your favourite motorcycle magazine? / Quel est votre magazine moto préféré?
/ Cual es su revista
de moto preferida?
USA CANADA
Forward to: / Envoyer a: / Enviar a:
Forward to: / Envoyer a: / Enviar a:
CIMA INTERNATIONAL, INC.
CLARY SPORTS LOISIRS
1585 Beverly Court # 118
67 ROUTE 329
Aurora, IL 60502
ST DONAT (QC) J0T 2C0
–
CANADA
Loading...