NBS Payment Solutions NOIRE510H1 User Manual

510H1

Wireless Terminal

USER GUIDE

NBS Payment Solutions Inc.
Corporate Headquarters - Canada
703 Evans Avenue, Suite 400
Toronto, Ontario, M9C 5E9
Canada

Tel: [phone]
Fax: [phone]

510H1 User Guide

UNPACKING THE

Carefully preserve the packaging of the terminal. It must
be re-used whenever the terminal is shipped.

Packaging contains:

 The terminal itself, equipped with its paper roll.
 Detachable power supply unit. (The power supply unit

delivered with your terminal is specially designed for
it. Do not use any other power supply.) The use of a
power supply having apparently similar
voltage/current characteristics may, in spite of this,
damage your terminal.

 Battery.
 Installation Guide.

510H1

SAFETY INSTRUCTIONS

To power down the

 Disconnect the power supply block from the

electric power supply network.

 Press and hold the

shuts off.

Electrical power supply network

Provide an A.C receptacle that meets the follow ing
recommendations:
 Connector is installed near the equipment and is

easily accessible

510H1:

key until the display

CHARGING THE TERMINAL

Select an electrical socket that complies with the general
safety instructions as outlined in “Safety Instructions.”

Connecting the Power Supply to the Optional Base

 Insert the small

connecter on the
power supply cable
into the socket at the
back of the optional
charging base.

 To charge the

terminal, gently place
the terminal on to the charging base.

Connecting the Power Supply directly to the

510H1

 Insert the small

connector on the
power supply cable
with the triangle
facing up, in to the
centre socket on the
back of the
510H1 terminal

 The terminal will

automatically power
on and start to
charge.

To decrease the charging time, the terminal may be
powered off by pressing the

shuts off.

key until the display

INSTALLING A ROLL OF PAPER

 Depress the printer

door release button
(see arrow) to
disengage the paper
door from the
terminal.

 Tilt the paper door

towards the rear of the terminal.

 Remove and discard the empty paper roll.
 Verify that the roller is intact and securely attached

to the paper door.

 Install the paper roll

(thermally coated side
exposed when viewed
from top) into the
compartment. The
thermally sensitive
side will create black
marks when it is
scratched.

 Tilt the paper door towards

the front of the terminal until
resistance is felt.

 Press down on both corners

of the paper door until it
clicks into position.

The

510H1 terminal is now ready for use.

INSTALLING A SIM CARD

The SIM card is located within the terminal.
 Power off the

terminal by pressing
the

the display shuts
off.

 Carefully remove

the SIM card cover
which is located on
the bottom front of
the terminal.

 Install the SIM card

with the notch
facing out. See the
picture for the
correct orientation
of the card within
the slot.

key until

FCC/IC COMPLIANCE

FCC ID: COL-NOIRE510H1
IC: 2279B-NOIRE510H1

This device complies with Part 15 of FCC Rules and
Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two con ditions:
(1) This device may not cause interference, and
(2) This device must accept any interference, including
interference that may cause undesired operation of the
device.

NOTE: This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation. This
equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is
no guarantee that interference will not occu r in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the
interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and
receiver.

-Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV
technician for help.

The equipment fulfills the applicable FCC requirements
with respect to RF exposure to electromagnetic fields,
when used for the purpose and in the way it is intended
and described.

WARNING: Changes or modifications to the equipment
that are not expressly approved by the responsible party
for compliance could void the user’s authority to operate
the equipment.

SAFETY INSTRUCTIONS

Electrical power supply network

Provide an AC receptacle that meets the following
recommendations:
 Connector is installed near the equipment and is

easily accessible