Naxa NX-671 User Manual

SPECIFICATIONS

GENERAL Supply Voltage DC 12V. Negative Ground Current Consumption Max.7A Power Output 4 X 7Watts. Number of channels 2 STEREO channels. Unit Dimensions 178[W] X 154[D] X 50[H] mm.

FM SECTION Frequency range 88MHz -108MHz Effective sensitivity 10uV. I.F Frequency 10.7MHz.

AM(MW) SECTION Frequency range 530KHz - 1700KHz

RCA LINE OUT Output CD Max. 800mV.

CD PLAYER System Compact Disc Audio System. Suitable CDs CD, CD-R, CD-RW Disc. Frequency characteristics 40Hz-100Hz <5dB 10KHz-20KHz <5dB. S/N Ratio to CD 60dB [1KHz]

Specifications subject to change, forgive without notification.

MODEL: NX-671

INSTRUCTION MANUAL

THEFT DETERRENT DETACHABLE PANEL CAR AUDIO CD, CD-R, CD-RW PLAYER AM/FM STEREO 2 BAND RADIO

Preface

Thank you for purchasing this car audio product. Please read this manual carefully before operating this car audio product. Please keep this manual for future use. It will be helpful to you if you are encounter any operational problem.

Selecting fine audio equipment is only the start of your musical enjoyment. Now it is time to consider how to maximize the enjoyment you will get from knowing how to work your new car stereo receiver.

We hope you enjoy using this product and encourage you to always listen at a moderate, safe sound level to avoid any possible hearing damage or loss. If you listen to excessively loud sound over time, your hearing can adapt to higher volumes and what sounds "normal" to you may be quite harmful and can cause you to have permanent hearing loss. So please practice "safe sound" and always listen at moderate sound levels only.

Start with your volume control at the lowest setting, and slowly increase the level until you can hear it comfortably and clearly, free from distortion. Once you have established this comfortable sound level, leave it there.

WARNING!

INSTALLATION

To reduce the risk of fire or electric shock, do not use the unit in the rain or moisture environment.

To prevent direct exposure to laser beam, do not try open the enclosure. Visible and invisible laser radiation when open and interlocks defeated.

To protect our environment, do not dispose of electrical equipment in the domestic waste. Please return any electrical equipment that you will no longer use to the collection points provided for their disposal. This helps avoid the potential effects of incorrect disposal on the environment and human health. This will contribute to the recycling and other forms of reutilization of electrical and electronic equipment. Information concerning where the equipment can be disposed of can be obtained from your local authority.

Page 1 Page 10

ANTENNA PLUG

WIRING DIAGRAM

LOCATION AND FUNCTION OF CONTROLS

CONSTANT B+

BLACK(GND)

IGNITION SWITCH RED (B+)

FRONT

LEFT

SPEAKER SPEAKER

REAR

YELLOW

FUSE 7A

RCA OUTPUT LINE

FUSE 0.5A

WHITE

WHITE/BLACK

GREEN

GREEN/BLACK VIOLET/BLACK

FUSE 0.5A

GRAY

GRAY/BLACK

VIOLET

RED R

WHITE L

BLUE AUTO ANT

FRONT

RIGHT

REAR

Note:

1. Make sure you use a speaker with 4 ohm load impedance

2. Make sure the auto antenna wire (Blue) does NOT come into contact with the vehicle chassis.

CAUTION:

In order to protect power IC from being burnt out during installation the car stereo, it is necessary to follow the steps below to connect the wires during installation:

Step 1: Connect the ground wire (Black); Step 2: Connect all speaker wires and power antenna wire (Blue): Left speaker Right speaker

Front speaker: White (+) White/Black (-) Rear speaker: Violet (+) Violet/Black (-) Step 3: RCA Line Out (R- Red/ L-White).

Step 4: Connect Back up (Yellow) and Acc wire (Red)

Green (+) Green/Black (-)

Gray (+) Gray/Black (-)

1. OPEN Button(OPEN)

2. Power(POWER) button

3. CD SLOT

4. LCD DISPLAY

5. EJECT(EJECT) key Volume up/menu up(+) button

6. Volume down/menu down(-) button

8. MODE(MODE) Button &

LOUDNESS(LOUD) button

9. Mute(MUTE) Button &

button

PAUSE,PLAY( )

10. Audio select(SEL) button

11. EQ (Preset Equalizer) Button

12. BAND(BND) Button & Track Repeat ON/OFF(RPT) button

TUNING KNOB

13.

14. STEREO/MONO Button & Track

INTRO ON/OFF (INT) button

15. LOC/DX Button & Track Random

ON/OFF (RDM) Button

16. TRACK DOWN/REVERSE

BUTTON( )

17. TRACK UP/FAST FORWARD

BUTTON( )

18. AUXILIARY INPUT JACK

Page 9 Page 2

General Controls

TROUBLE SHOOTING

1. OPEN BUTTON

To remove the front panel from the main body, press the OPEN key. And the anti-theft LED indicator will be flashed all the time till the front panel be refixed into the main body.

2. POWER ON/OFF

In power off (ACC on) mode, turn on the unit by pressing the POWER button on the front panel; It also can turn on the unit to insert a disc into CD slot. It will start play the first track on the current disc. Press the POWER button short to turn off the unit.

3 & 4.VOLUME UP(+)/DOWN(-) BUTTONS

Press the volume UP(+) or DN(-) button short or hold to raise or lower the volume level during playback. The both buttons are also used to adjust the settings for Bass, Treble, Balance, Fader, when you are in those audio modes.

5. MUTE ON/OFF BUTTON (Only for radio mode)

This button serves to switch the MUTED state on/off during RADIO mode. Press the mute(MUTE) button short to suppress the speaker temporarily. Press it again to resume listening.

6. AUDIO FUNCTION AND MENU SELECT/ADJUST

1)Audio mode select and adjustment: Press the SEL button repeatedly to cycle through four audio modes:

-> VOLUME ->BASS ->TREBLE -> BALANCE -> FADER After selecting a certain audio mode, you can adjust the setting for Bass, Treble Balance, fader by pressing the UP(+) or DN(-) button. The control mode of E.VOL is operated with following numeric display.

- VOL: (MIN)00, 01,......45, 46(MAX).

- BASS/TREB: -6, -5,...,00,...5,6

- BAL: 9L, 8L,...,00,...8R,9R

- FAD: 9F,8F,...,00,...8R,9R In each mode, the waiting time is about 3 seconds, and the waiting time is over, it returns to the last display mode of RADIO or CDP mode.

Before using the check list please make all the connections first. If you still have questions after going through the checklist, please consult your local customer service representative.

PROBLEM

No power

Disc cannot be loaded or ejected

No sound

Sound skips

Another CD is present in the player

Disc incorrectly inserted upside-down

CD is extremely dirty or defective

Temperature inside the car is too high

Condensation

Volume is too low Wiring is not properly

connected The installation angle is more

than 30 degrees CD is extremely dirty or

defective

CAUSE

The car ignition is not on.

The fuse is blown

SOLUTION

If the power supply is properly connected to the car, switch the ignition key to " ACC "

Replace the fuse

Remove CD in the player, then insert a new one with label face up

Insert the CD with label face up

Clean the CD or try a different CD

Give enough time for the temperature in the vehicle to cool down.

Turn off the player for at least an hour, then try again.

Adjust volume to desired level Check the wiring connection

Adjust the installation angle to less than 30 degrees

Clean the CD or try a different CD

7. EQ BUTTON

Press the EQ button short to access the preset equalizer mode. Press it

repeatedly to choose EQ OFF, or 4 preset equalizer curves: FLAT, CLAS,

ROCK, POP. The audio output will change correspondingly.

8. LOUDNESS BUTTON

Pressing and holding the LOUD button to enhance the bass output when low volume level. Pressing and holding it again to cancel loudness effect.

Page 3 Page 8

The radio does not work

The antenna cable is not connected

Insert the antenna cable firmly

+ 8 hidden pages