Thank you for choosing Nawras E5 II Wi-Fi modem
Nawras E5 II Wi-Fi modem is a high-speed packet access (HSPA) USB
modem. You can connect E5 II with the USB interface of a computer, or via
Wi-Fi. It is a multi-mode wireless terminal for SOHO (Small Office and
Home Office) and business professionals connecting up to 5 users
wirelessly and can access Internet, send and receive emails, SMS, manage
your phonebook contacts, check balance, recharge and even subscribe to
our Prepaid Internet products.
Note:
The supported functions and actual appearance are subject to product
purchased. The following pictures are displayed for illustration
purpose only. For details of your product selection, consult your
service provider.
This guide briefly describes the function of the device. For advance
configuration, see Help on web management page of E5 II modem by
logging to http://192.168.1.1.
1
E5 II can be kept in a reasonable closed environment such as handbag
or laptop bag, however if the ambient temperature increases as a
safety precaution the device will switch off automatically or disconnect.
In such event please restart your device.
Getting to Know Your E5 II
Packing List
The E5 II box contains the following items. If any of the items are lost or
damaged, contact your local dealer.
2
Quick Start
Safety
Information
Main unit Battery Power adapter
& data cable
Application Scenarios
The Wi-Fi device or computer can be connected to the Internet through the
E5 II. The actual connecting procedure depends on the operating system
of the Wi-Fi device or computer. You can perform the connection
operations as prompted.
Scenario 1: Multi-device access via Wi-Fi Scenario 2:
One-device access via USB
3
Digital camera
Laptop
Smart phone
Game machine
Scenario 3: Multi-device access via Wi-Fi and USB at the same time
4
Smart phone
5
Game machine
Laptop
Digital camera
2
1
3
4
5
6
8
7
Appearance
No. Item
Screen
microSD card
USB
port
Power
button
Wi-Fi
/WPS
Dial
ing button
Strap hole
Battery
button
1
2
slot
3
4
5
button
6
7
8
Wi-Fi: Wireless Fidelity
WPS: Wi-Fi Protected Setup
7
7
8
12435
6
No. Item
Signal s
trength
Network
Wi-Fi enabled
I
nternet connection
New messages
P
ower level
Roaming stat
e
M
: Manual mode
Screen
1
2
3
4
5
6
7
8
Number of devices
connected
Number of new messages
A: Auto mode
8
Before you start
Before inserting the SIM card and battery, please
note down Wi-Fi network name (SSID) and password
(Wi-Fi key) which is printed on the label next to SIM
card slot.
Installing the SIM card and the battery
Hold the E5 II modem with USB connector facing down and press the top
button to remove the back cover and battery and insert the SIM as shown.
9
1
2
3
4
Installing the microSD card
1. Pull the rubber cap from the microSD
card slot and insert the card.
Note:
The microSD card is an optional accessory. If the microSD card is not
provided in the package, you can buy one yourself.
To remove the microSD card, open the rubber cap and press the
microSD card gently.
Do not remove the card when it is being used. Otherwise, the card and
the E5 II may be damaged, and the data stored on the card may be
10
lost.
Charging the Battery
Note: If you have not used the E5 II modem for a long time, please charge
the battery first.
Method 1:
Caution:
By using the power adapter
Use the compatible power adapter priovided inside the box only.
Nawras is not responsible for any damage caused due to incompatible
power adapter.
11
Method 2:
1. Power off the E5 II modem.
2. Connect it with PC using compatible
By connecting to a PC
data cable.
Accessing the Internet through a Wi-Fi Connection
Note: Your E5 II modem is preconfigured with Wi-Fi network name (SSID)
and password (Wi-Fi key). You can follow the steps below to quickly access
the internet. For the details about how to set the parameters, see the Help
on the Web management page (http://192.168.1.1)
Step1: Power ON the modem.
Step2: Establish a Wi-Fi Connection.
12
Step3: Access the Internet.
1. Power ON the modem
Press and hold to switch ON/OFF
the modem.
2. Establish a Wi-Fi Connection (considering Windows XP
as an example)
1. Make sure that the Wi-Fi function is
enabled.
2. Select Start > Control Panel >
Network Connections >
Wireless Network
Connection.
Note: To set up a Wi-Fi connection, the
13
PC must be configured with a wireless network adapter. If Wireless
Network Connection is displayed, the wireless network adapter is
available.
3. Click View available Wireless Networks to display the wireless
network list.
4. Select the Nawras E5832-xxxx from the list and click .
14
5. Please enter the password (Wi-Fi key)
once the Wireless Network Connection
dialog box is displayed.
Note:
You can find Wi-Fi network name (SSID) and password
(Wi-Fi key) on the E5 II exactly below the battery.
Wait until the wireless connection icon is displayed in
the status area.
3. Access the Internet
15
After you establish a Wi-Fi connection successfully, you can access the
Mode
Operations
Auto
In this mode, E5 II will
connect a
utomatically to the
Manual
Internet in either of the following two modes. By default, the mode is set
to Auto.
Internet when data transmission is requested. If data
transmission is not performed over a period of time, the
E5 II automatically disconnects from the Internet
Press and hold
is displayed on the screen.
CONNECT
until
When is displayed on the
screen, it indicates that the
connection is set up successfully. Then you can enjoy the
Internet service.
Press and hold
CONNECT
until disappears. When
disappears, it indicates that the connection to the
16
Mode
Operations
Internet
is
disconnected
.
Note: You can use web management page to connect to or
disconnect from the network as prompted.
Note:
You can launch the web management page to select the mode of
accessing the Internet.
While roaming E5 II automatically disconnects from the established
network and then you have to manually connect by pressing and
holding
The dialing button does not work in Auto mode.
CONNECT
button.
17
Accessing the Web Management Page
1. Make sure that the connection between the E5 II and your PC is
established either by USB cable or over Wi-Fi.
2. Start the Internet browser and enter http://192.168.1.1 in the
address bar.
3. Enter the password, and then click Login.
Note: The default password is admin.
Verifying the PIN Code
Please launch the web management page by typing http://192.168.1.1
and then enter the correct PIN code as prompted. Both the PIN and PUK
are delivered with the SIM card. For details, consult your service provider.
Sharing data stored on the microSD card
E5 II supports data sharing using web management page. You can store
18
data on the card and share it with the group.
1. Insert the microSD card.
2. Access the web management page.
3. Click SD Card to manage the data stored on the microSD card.
SMS
You can enjoy the short message (SMS) service on the web management
page.
1. Access the web management page.
2. Click SMS to view, write, reply, or send a message.
19
Daily Use
Saving Power mode
If no operation is performed for a while, E5 II screen will be off.
It will go into deep sleep mode if not accessed for 30 minutes. In this state,
you can press any key to activate the Wi-Fi function.
Enabling/Disabling the Wi-Fi
Function
To switch ON Wi-Fi, press and hold
until is displayed on the screen.
Note: To switch OFF Wi-Fi, press and hold until
disappears.
20
Establishing a WPS Connection
If the Wi-Fi clients connected to the E5 II support the WPS function, the E5
II can generate a network key without manual input. To establish a WPS
connection, please follow the below steps:
1. Power on the E5 II modem.
2. Start the Wi-Fi clients.
3. Enable the WPS function on E5 II by pressing and holding
key,
4. Enable the WPS function on clients.
Note: For the Wi-Fi operations of the clients, see the clients’ user guide.
21
Restoring the Factory Defaults
To reset the configuration to factory default settings, press and hold
Note: After factory defaults are restored, all personal configurations are
deleted and all web-based management settings and parameters are
restored to their default values.
and
CONNECT
at the same time until the screen is off.
Tips
If you are facing any problem with E5 II modem, please try the followings:
See Help on the web management page.
Restart the E5 II modem.
Restore the factory defaults.
Contact your service provider.
22
Example: Wi-Fi Connection to Game Machine (PSP)
1. Turn on the PSP WLAN
switch.
2. Select Settings > Network
Settings.
3. Select Infrastructure Mode
to connect your local Wi-Fi access point.
4. Select New Connection to
specify a mnemonic
connection name (such as
MyE5 II).
5. Select Scan to detect
networks in the range.
23
6. Select the Nawras
E5832-xxxx from the list.
Then press the > button
consecutively to confirm the
SSID and input the Wi-Fi key.
The default Wi-Fi network
(SSID) and password (Wi-Fi
key) are attached on the E5
II exactly below the battery.
7. Press the > button to continue, and then press X to save settings.
8. Select Test Connection to check the connection. Once successful you
play online.
24
Example: Wi-Fi Connection to smart
phone (iPhone)
1. Select Settings > Wi-Fi and turn
Wi-Fi ON.
2. Automatically detect networks in
range.
3. Select the Nawras E5832-xxxx (name
of your device).
4. Enter the password and tap Join.
(Networks requiring a password
appear with a lock icon.)
Note: The Wi-Fi Clients such as iTouch,
PS3, and NDS can also access Internet
via the E5 II. For details about the
operation, follow the user guides of
25
the Wi-Fi Clients.
26
Frequently Asked Questions (FAQ)
What can I do if the client connected to the E5 II cannot
access the Internet?
1. Check and ensure that the client is connected to the E5 II properly.
2. Check the power status to ensure that the E5 II is powered on.
3. Check the signal strength to ensure that the area is covered by the
network.
4. Check that the network mode is correct. For details about network
modes, see Mobile Network Settings on the management page.
5. If the DHCP server is disabled and the client obtains the IP address
dynamically, the device cannot access the Internet either. In this case,
you need to change the mode to manually assign an IP address. See
DHCP Settings on the management page.
6. Check that the network adapter of your client runs properly.
7. If the problem still persists, please consult you service provider.
27
What can I do if the client cannot access the WLAN?
1. If there are interferences or shields near the E5 II, you can adjust the
position of the E5 II.
2. Check and record the following settings of your Wi-Fi client and E5 II:
Wi-Fi network (SSID) and password (Wi-Fi key). All these parameters
should match with each other; otherwise you may need to change the
settings.
What can I do if I forgot the default IP address of the
management page?
1. You can enter http://e5 .home in the address bar and log in to the
management page to obtain the IP address automatically.
2. Restore the factory defaults.
28
Version: V100R001_01 Part Number: 31010EQV
29
Loading...