NAV-TV X164 User Manual

Camera Interface for

To Activate Video Monitoring

Fig. 2 - Video Activation

Press the steering wheel
(+) and (-) buttons simultaneously to
activate Video.

Pressing any MODE button will return
the screen to it!s normal operation mode.

OR:

Press the steering wheel
(hang) and (-) buttons simultaneously to
deactivate Video.

2006-Up Mercedes-Benz GL, ML, R

Class SUV’s

T-Harness

NTV-HAR069

V1 Switcher shown here, this

has been replaced with the

X164 Module

NTV-ASY107

USB Cable

NTV-CAB009

Operation Instructions

3950 NW 120th Ave Coral Springs, FL 33432

Tel. [phone] Fax. [phone]

X164

NTV-KIT041

Kit Contents

VSW-R in 03/15

NTV-DOC026

[e-mail]

Compatible with Alpine made US MCS Comand
Head units. Mercesed P/N ending with 1779, 1789,
3879, 4089, 4079 3689. See 3rd page picture for
example. ��

European Head units

Not compatible with Models not listed or

VSW-R I/O Harness

NTV-HAR257

VSW-R Board
NTV-ASY187

VSW-R Trigger Harness

NTV-HAR066

X164

BHM 3/18/15

To Activate Rear View Camera Fig. 1 - Vehicle in Reverse

With the brake depressed and engine
running, engage reverse gear.

Rear View Camera picture will show on
COMAND screen.

Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. Would not be held liable for misuse of it’s product.

WARNING: Check entire surroundings while backing. Do not become distracted by using COMAND.

If you do not agree, please discontinue use immediately and return product to place of purchase.

This product is intended for off-road use and passenger entertainment only.

Wiring

Fig. 2 - Car Wiring Vs. X164

1. Unplug factory power connector from
radio. Plug in the X164 adapter harness to
factory harness, Radio and X164 Module.

2. Female RCA: Video input to COMAND.

3. Male RCA: Output of Factory Camera.

White / Blue

+12V Reverse OUT, 500mA

White / Red

+12V Acc. OUT, 500mA

Programming - Proceed only once !

Fig. 3 - Programming

Simultaneously Press the steering wheel
(Talk) and (Hang) and (+) and (-) buttons to
program radio. Observe the DIAGNOSIS
message on the radio followed by a radio
reset.

Remove Radio

Fig. 1 - Radio Removal (GL Class)

1. Remove TORX Screws behind ashtray.

2. Remove ashtray.

3. Pull, remove bottom of A/C Wood Trim.

4. Remove TORX Screws securing locks.

5. Pull down locks, Remove Radio.

3950 NW 120th Ave Coral Springs, FL 33432

Tel. [phone] Fax. [phone]

[e-mail]

X164

Camera Interface for 2006-Up Mercedes-Benz GL, ML, R Class SUV’s

Compatible with Alpine made US MCS COMAND Head units, Mercedes P/N ending with : 1779, 1789, 3879, 4089,4079 3689

Not compatible with Models not listed or European Head units

Installation Instructions

X164

BHM 3/18/15

NTV-DOC026

Connect to Video source or Camera, or to
supplied video switcher if 2 video sources
are present (Video OUT).

Plug into switcher If camera present
(Video 1).

Video Switcher: connect Black wire to

4.
ground, White/Red wire to White / Blue on

X164 (Reverse +12V out). The switcher
will then activate automatically when in
Reverse.

Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. Would not be held liable for misuse of it’s product.

If you do not agree, please discontinue use immediately and return product to place of purchase.

This product is intended for off-road use and passenger entertainment only.

WARNING: Check entire surroundings while backing. Do not become distracted by using COMAND.