NAV-TV Volvo CAM, Volvo CAM12 User Manual
JR, BM
Overview
Kit Contents
Volvo Cam module
NTV-ASY160
NAV-TV CAM 6
NTV-CAM046
SMB to RCA adapter
NTV-CAB007
USB Cable (updates)
NTV-CAB009
Plug & Play T-Harness
KIT294: NTV-HAR207
KIT368: NTV-HAR204 & NTV-HAR207
CAM 6 Extension Power/Signal
NTV-CAM046
10/20/13
NTV-DOC091
3950 NW 120th Ave, Coral Springs, FL 33065 TEL 561-955-9770 FAX 561-955-9760
www.nav-tv.com info@nav-tv.com
Volvo CAM/Volvo CAM12
NTV-KIT294/368
The Volvo Cam kit adds an aftermarket back up camera to the factory 6.5” screen in select
Volvo vehicles. Additionally, this module will enable video in motion (VIM) and navigation
control in motion (CIM) if equipped. This installation requires no cutting of any factory wires
and is fully Plug & Play behind the media screen.
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
1 | P a g e
JR, BM
Volvo Cam Module Pin Outs
Pin #
Description
Color
1
12v Constant (+)
Yellow
5
-not used-
Gray 6 -not used-
Blue
8
CAN HI (Radio Side)
Green
9
CAN HI (Vehicle Side)
White
10
Ground (-)
Black
11
Output 1 (12v w/ CAN)
White/Red
12
Output 2 (12v w/ REV)
White/Blue
13
Output 3
White/Purple
14
-not used-
Gray/White
15
-not used-
Pink/Black
16
-not used-
Pink
17
CAN LO (Radio Side)
White/Green
18
CAN LO (Vehicle Side)
Brown
Module Programming
Wire Side
10/20/13
NTV-DOC091
1. The Volvo Cam module will come preprogrammed with the most popular working file,
but you may need to adjust it for your particular Volvo type/year.
2. Refer to https://navtv.com/products/NTV-KIT368/volvo-cam-12.html and click on the
‘Files’ button at the bottom.
3. After downloading, unzip the compressed folder into another folder.
4. If you’ve never updated a NAV-TV module before, you’ll need to install one of the USB
drivers from the same unzipped folder (win 7+ or XP driver, respectively).
5. Open the Volvo USB Updater (blue icon) found in the extracted folder from step 3.
6. Connect the Volvo Cam module to the computer using the provided USB to mini-USB
cable.
7. The ‘USB Device’ field should populate after 5-10 seconds.
8. Click the 3 dots at the top right of the updater window. Navigate to the same extracted
folder from step 3. Select the ‘VolvoVIMCam.enc’ file and press ‘Open’.
9. Double click ‘ON’ for VIM or address in motion to adjust ON or OFF.
10. Double click ‘ON’ for Rear view camera to adjust ON or OFF.
11. Double click ‘off’ for Front view camera to adjust ON or OFF.
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
2 | P a g e
Loading...