NAV-TV PCM3CAM-USB User Manual

3950 NW 120th Ave, Coral Springs, FL 33432

Tel. [phone] Fax. [phone]

PCM3CAM-USB

www.nav-tv.com [e-mail]

Front and rear camera interface

Enables a backup camera and a secondary on the factory 2009 and Up Porsche PCM 3.0 Radios

Certain features are intended for passenger and off-road use only. User must obey
all State and Federal regulations

Make sure your radio looks like this

prior to installation

Kit Contents

USB Cable (Updates)

NTV-CAB009

PCM3-CAM Module

NTV-ASY107

Plug & Play Harness

NTV-HAR111

PCM3CAM

NTV-KIT100

Rev 2 BHM 03/18/15

NTV-DOC045

VSW-R Trigger

Harness

NTV-HAR066

Filter Harness Description and Diagram

Wire Functions Wire Colors Fig. 2 - Connection plug on Can Filter

1. CAN Hi to Vehicle.

2. CAN Lo to Vehicle

3. Chassis Ground.

4. +12V Output to Camera.

5. CAN Hi to PCM.

6. CAN Lo to PCM.

7. +12V Battery

8. +12V Output to switcher and front Flir IR camera.

VSW-R Board

NTV-ASY187

1. Yellow

2. Blue

3. Black

4. White/Red

5. Yellow

6. Blue

7. Red

8. White/Blue

VSW-R Harness

NTV-HAR257

V1 Switcher shown

here, this has been

replaced with the

VSW-R in 03/15

8 pin Molex connector

Wire side view

1 | Page

Installation Part 1

1. Insert a soft pry tool into the space between the lower black fascia
piece and the lower side of the dash and gently pry the fascia towards
the rear of the vehicle to release the mounting clips. Follow the fascia
around either clockwise or counterclockwise to release the remainder of
the mounting clips. Set aside the fascia.

2. Remove (4) t20 torx screws from the sides of the
radio and pull the radio gently out of the dash in order
to disconnect all stock cables and antenna
connectors.

3. View of rear of radio and stock radio harness.
Remove the fiber optic connector from the original
harness by gently prying up on the locking tab with a
pick tool.

4. With the fiber unplugged from the factory harness
plug the aftermarket harness into the original harness
and secure it by closing the stock locking tab. Attach
the PCM3CAM module to the aftermarket harness
and secure the filter to the back of the radio cavity with
either double sided tape or Velcro. Fold the harness in
the cavity as shown to allow clearance for the radio.

2 | Page

Installation Part 2

5. Drop the plastic panel over the passenger side kick panel area
by taking out (1) t20 Torx screw and pulling the panel towards
the floor. Run the black, white/blue and white/red wires from the
new radio harness into the opening as in the picture to your left.
These wires will power your reverse and front cameras, as well
as the video switcher.

6. If your vehicle is not equipped with a stock camera and you are
not installing a front camera then simply unplug the male RCA end
from the female in the aftermarket harness and run your camera’s
video RCA directly to the female plug. Connect ground for the
reverse camera to the black wire and 12 volt positive to the
white/red from step 5 and insulate the white/blue wire. Skip to step

8.

Vehicles with factory camera VSW-R installation

7a. Extend and plug the female RCA (radio side) of the harness into AV1
out. Extend and plug the male RCA (vehicle side) into AV1 in. Connect a
front camera, for example, a Flir night vision camera RCA into Video 2 in.
Connect the black ground wire from step 5 to both the ground of the front
camera and the ground (black wire) from the video switcher. Connect the
12v wire (Video 2 Trig) of the switcher (white/red wire) to the white/blue
wire from the module.

Vehicles without factory camera switcher installation

7b. Extend and plug the female RCA (radio side) of the harness into

Video Output. Plug the RCA from your aftermarket rear view camera into
Video 1 input (VSW-R). Connect a front camera, for example, a Flir night

vision camera RCA into Video 2 in. Connect the black ground wire from
the switcher to the ground from the switcher, the reverse camera and the
front camera. Connect the white/red wire to the 12v wire to your
aftermarket back up camera. Connect the white/blue wire to the 12v wire
on your front vision camera

8. Plug the fiber optic cable you unplugged in step 3 into the aftermarket
harness. Reconnect all the antenna, power and all other connectors back
into the radio and slide the radio back into the dash. Reassemble in the
reverse order as steps 1,2 and 5. Now you are ready to proceed to the
programming and operations section. Good job!

3 | Page

Programming

1. Press and hold down the + button
on the stee
continually holding down the +
button, pre
mute button. Continue to hold
down the mute button and
the + button.

3. After the radio reboots first select the option button on

the right of the PCM. Then
then make sure the “automatic” feature is highlighted.
Automatic means that every time the vehicle goes into
reverse the PCM screen will show the backup camera
image.

select “rear view camera” and

ring wheel. Whil

ss and hold do

2. The radio screen will now display the word
SERVICE. While SERVICE is displayed on the screen
press the up arrow within 7 seconds and Hold for 4
seconds to program the PCM for a reverse camera. If
the PCM3CAM module is ever removed from the
original vehicle you must first enter service mode and
press the down arrow for 4 seconds to deprogram the
original PCM BEFORE the filter is removed. If this is
not done the filter will not work on any other vehicle.

e

wn the

releas

e

Operation

1. Place the vehicle in reverse and your image will appear on
the scree
will stay on the screen for up to 20 seconds or until the
vehicle rea

2. To enable the rear view camera while in motions simp
doubl
the came
again.

3. It the s
doubl
reverse

4. No matter what is showing on the screen the PCM will swit
over to the re
placed into reverse.

5. This module is only intended for front and rear view cameras.
You will always have the “Pay Attention To Vehicles

Surrounding

Note: Camera will not operate when the rear hatch is open.

Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for misuse of its product.

If you do not agree, please discontinue use immediately and return product to place of pu ase. rch

This product is intended for off-road use and passenger entertainment only.

n. When putting the vehicle ba

ches 7 mph.

e click the mute button within 1 second. To deact

ra while in motion double click the mute butto

witcher is used to switch between two cameras,

e click the mute command will alternate betwee

camera, factory screen, front camera, factory screen.

verse camera image any time the vehicl

s” disclaimer at the top of the screen.

ck in drive the image

ly

n

e is

ivate
n

the

ch

4 | Page