Telephone: + 44 (0)870 801 0440
Fax telephone: + 44 (0)870 801 0441
technical@nav.tv
Unit R4
Capital Business Park
Wentloog
Cardiff
CF3 2PU
NAV-INJAG
NAV TV (UK) LTD
NAV TV (UK) LTD
VIDEO INPUT
ALL JAGUAR
Without TV Tuner
The video input is auto video sensing, when
your additional source is switched on the picture will override the navigation map picture. It
will revert back to the navigation picture when
your source is switched off.
The second input (Camera Input) is activated
when the Blue cable is made live (adding a
12v+ supply) This input will override the additional source or the navigation map when activated.
OPERATING INSTRUCTIONS
e11*72/245*95/54*3583*00
RoHS 2002/95/EC—2002/96/EC
Disclaimer
NAV TV (UK) Ltd is not liable for any incidental, consequential or indirect damages. In case of erratic behavior of the vehicle’s electrical
system please disconnect the NAV TV product and contact our technical support Team. NAV TV (UK) Ltd does not assume liability for any
diagnostic fees.
LOCATION & REMOVAL INSTALLATION
XKR
All the wires can be accessed at the rear of the front screen.
The wires are in the 16 way plug (there are 2 plugs a 12 way
and a 16 way)
XJR & new XJ / XJR
All the wires can be accessed at the rear of the front screen
connect to the centre 26 pin plug. For new XJ & XJR with 22
pin plug follow wire colours not pin numbers.
Car Harness
NAV-INJAG
Orange (pin 14) to Red
Yellow (pin 2) to Green
Green (pin 15) to Blue
White / Black (pin 1) to Yellow
Shield (pin 16) to Shield
S Type (2006)
All the wires can be accessed at the rear of the front screen
in 22 pin Black plug
Car harness
NAV-INJAG
White (pin6) to Red
Green (pin7) to Green
Red (pin 17) to Blue
Yellow (pin 18) to Yellow
S TYPE up to 2006
All the wires can be accessed at the rear of the front screen.
Car Harness NAV-INJAG
Grey / Red to Red
Grey / Orange to Green
Grey / Violet to Blue
White/Black to Yellow
Shield to Shield
XK8
All the wires can be accessed at the rear of the front screen.
The wires are in the centre 26 pin plug
Car Harness
NAV-INJAG
Orange (pin 14) to Red
Yellow (pin 2) to Green
Green (pin15) to Blue
White/Black (pin1) to Yellow
Shield to Shield
Other connections (on all cars)
YELLOW to 12v+ ignition / accessory
BLACK to 12v- ground
RED to 12v+ to activate video input (also auto
switching)
BLUE to 12v+ to activate camera input
INSTALLATION
Locate the cable which connects the Navigation computer with
the monitor. Within this cable you will find the cable colours
given opposite. You will then need to cut open the these cables
and connect the input and output cables from the supplied harness as the diagram below shows.
X TYPE
All the wires can be accessed at the rear of the front screen.
Car Harness
NAV-INJAG
Yellow (pin 6) to Red
Green (pin 7) to Green
Orange (pin 17) to Blue
White/Black(pin18) to Yellow
White (pin 8) to Shield
INSTALLATION
Navi
Screen
-12v Ground (black)
+12v Acc (yellow)
02
01
Interface diagram
NAV (Input)
SCREEN (Out)
16 15 14 13 12 11 10 9
8 7 6 5 4 3 2 1
Rear of plug
RED
SHIELD
SHIELD
SHIELD
GREEN
BLUE
WHITE
TO YELLOW
TO RED
TO GREEN
TO BLUE
16 WAY PLUG
Loading...