NAV-TV MOST-AUX User Manual

MOST-AUX

Fiber-optic AUX input for select MOST vehicles

NTV-KIT001/002/007/008/143/151/152

BHM

01/26/15

NTV-DOC006

3950 NW 120

th

Ave, Coral Springs, FL 33065 TEL [phone] FAX [phone]

I N T E R F A C E

BHM

Vehicle

Compatible Interface

Hardware TYPE

Manual Page

Aston Martin

MOST-AUX Aston

1

4

Audi

MOST-AUX Audi

1 5 BMW

MOST-AUX BMW

1

5 & 6

Mercedes

MOST-AUX MB

1

7

Porsche

MOST-AUX POR

1

8 & 9

Jaguar

MOST-AUX JAG

2

6

Land/Range Rover

MOST-AUX RR

2 7 Volvo

MOST-AUX Volvo

2

9

Kit Contents

Overview

MOST AUX module

NTV-ASY149

Power/RCA

Harness

NTV-ASY012

Fiber optic cable

NTV-ASY03

MOST Bypass (MB only)

NTV-CON001

USB cable

NTV-CAB009

01/26/15

NTV-DOC006

The NAV-TV MOST AUX module is a M.O.S.T. fiber optic auxiliary audio input interface that
introduces audio into select MOST fiber optic equipped vehicle with no degradation in sound
quality. There are TWO HARDWARE PLATFORMS: TYPE 1 & TYPE 2 THAT ARE NOT
INTERCHANGEABLE. Although you cannot use a Type 1 hardware in a Type 2 vehicle (and vice
versa), the software coding and installation is the same for both. The following chart lists
compatible vehicles and platforms:

rB7

This module can be installed in any position within the fiber optic loop.

Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.

2 | P a g e

Installation Overview (ALL vehicles)

MOST-AUX MB: This specific kit (only) will include a fiber
optic bypass loop. In this car, the CD changer MUST be
bypassed for the MOST-AUX to function properly.

Before

After

Factory MOST

Fiber Optic cable

Supplied NAV-TV
MOST-AUX Fiber

- Black wire: Connect to chassis ground.

- Red wire: Connect to 12v Constant

- Blue wire: Supply 12v + (through a toggle switch) to

activate AUX input

- Fiber optic cable configuration (see diagram at right):

BHM

01/26/15

NTV-DOC006

rB7

General Install notes:

- Do not grab power from the CD Changer’s power harness.

- Grabbing power from the radio’s harness may cause problems as well.

MOST AUX Note: For most vehicles, this kit will work right out of the box. However, some
vehicles will require setup adjustments via the USB and the Nav-TV USB updater program. The
following 7 pages will cover the qualifications and setup walk-throughs for each car, if
necessary.

Installation of the Nav-TV USB Updater:

Using Windows XP or Windows 7:

1) Download the device driver form navtv.com>support>downloads at the top of the screen in
BLUE that says updated driver and save it to A NEW FOLDER ON THE DESKTOP. .

2) Install the driver. It will ask you if you want to update the driver during installation. Click yes
and proceed through all installation steps. If prompted to restart the computer do so at this
time. If not proceed to 3.

3) Download and unzip the proper file packet for the corresponding NAV-TV product (follow the
exact same directions you would follow if the computer did not have DEI© software on it)

4) Launch the USB Updater program and plug in the NAV-TV device to an available USB port.

5) If it recognizes right away you are done. If not, proceed to step 6.

Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.

3 | P a g e