NAV-TV AUDI DYNAMIC-INT Installation Manual

BHM

11/21/17

NTV-DOC242

Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.

1 | P a g e

3950 NW 120th Ave, Coral Springs, FL 33065 TEL [phone] FAX [phone]

www.nav-tv.com [e-mail]

AUDI DYNAMIC-INT

NTV-KIT700

Overview

The AUDI-DYN INT Kit interfaces a backup camera (with dynamic guidelines) and one additional
video input (front cam, etc) to the factory media screen in select Audi vehicles with the Concert
media system (MMi controls on vertical radio face, not console).

Kit Contents

VIDEO Input RCA

Power/CAN Harness

LVDS-IN Cable

AUDI-DYN INT Interface

OSD Menu

Remote

LVDS-OUT Cable

IR-Eye

Cable

Input
Toggle
Switch

HD-LINK Optional KIT800

BHM

11/21/17

NTV-DOC242

Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.

2 | P a g e

Upon button presses

Interface Connectors

Dip Switch Settings

Dip SW:

1 2 3 4 5 6 7 8 9

10

UP

Skips

RGB

Skips

V1

Skips

V2

RVC OFF

N.C.

N.C.

N.C.

N.C.

HIGH

RES

Keep

Down

DOWN

Enables

RGB

Enables

V1

Enables

V2

RVC ON

N.C.

N.C.

N.C

N.C.

LOW

RES

Keep

Down

Power/CAN

Dip Switches

Note: If the dip switches are not configured prior to
installation you must remove power to the unit prior to
making adjustments to the dip switches.

LVDS-IN

LVDS-OUT

RGB IN

Not Used

HDMI Cable from HD-LINK

Not Used

BHM

11/21/17

NTV-DOC242

Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.

3 | P a g e

AUDI-DYN-INT Installation

1. Remove the factory screen. This requires removing the plastic screen bezel and then

(4x) Torx T20 screws. Disconnect the 10-pin harness from the screen and set the screen
aside.

2. Remove the factory radio (CD player). Disconnect all harnesses and set the radio aside.

3. Connect the provided LVDS-OUT Cable to the OEM screen.

This connector is keyed and will only fit in one direction. The
other end of this cable connects to the interface at the port
labeled ‘LVDS OUT’.

4. Connect the provided LVDS-IN Cable to OEM 10-pin square connector previously

connected to the screen (removed in step 1). The other
end of this cable connects to the interface at the port
labeled ‘LVDS IN’.

5. Optional: If adding an additional video input (front camera etc.), connect the

provided Video Input RCA to the port on the AUDI interface labeled ‘AV
IN’. Connect the video signal to this RCA, be certain the video source
is powered with an ACC source.

6. Optional: If this car is not equipped with OEM rear parking sensors, you may turn the

visual overlay off in the OSD menu system (see page 5 for menu information).

Note: If adjusting any OSD menu settings, temporarily connecting the provided AV

toggle switch and IR-Eye is required. Both harness connectors are located among the main
power harness (2-pin & 3-pin).

ATTENTION INSTALLER: All connections (including CAN) must be made BEFORE

connecting the power harness to this unit for proper startup operation.