NAV-TV AUDI DYNAMIC-A3 Installation Guide

BHM

Overview

Kit Contents

Infrared Receiver

OSD Menu Remote

Power/CAN Harness

A-Type

LVDS
Video
Cable

DYNAMIC-A3 Interface

AUDI 3G-CAM NTV-CAM072

Optional: NTV-KIT496

11/20/15

NTV-DOC244

3950 NW 120th Ave, Coral Springs, FL 33065 TEL [phone] FAX [phone]

www.nav-tv.com [e-mail]

AUDI DYNAMIC-A3

NTV-KIT702

The AUDI DYNAMIC-A3 Kit interfaces a backup camera input (with active parking lines) and 1
additional video input (front cam, etc) to the factory media screen in the 2014+ Audi A3 or VW
Golf 7. Installation is performed behind the MMI (inside glove box).

Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.

1 | P a g e

BHM

Interface Connectors

Dip Switch Settings

---

AUX VID 1

AUX VID 2

RVC

TRANS*

iNAV button**

RES

---

Dip SW: 1 2 3 4 5 6 7 8

UP

Keep UP

OFF

OFF

OFF

AUTO

OFF

HIGH

Keep DOWN

DOWN

Keep UP

ON

ON

ON

MANUAL

ON

LOW

Keep DOWN

Power/CAN Harness

For Video

Expansion

Board

Dip Switches

Note: Remove power to the unit prior to making adjustments to the dip switches

Note: Dip Switches 1 & 8 must be left in the position indicated above for proper operation

**iNAV button: Activates AUX Video (optional)

Video OUT
(to screen)

Video IN (from

radio)

Not Used

Not Used

RGB IN

11/20/15

NTV-DOC244

Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.

2 | P a g e

Installation (A3)

Interface wires

Connect to car

Location

Black (Ground)

Chassis Ground

PIN 15 (Radio plug)

Red (ACC 12v)

ACC 12v (+)

Black/White @ pass fuse box

Green (Rev 12v in)*

Reverse Lamp (+)

---

*NOTE: You may need to shave

some keyways on the factory
connector in order for it to fit

into the VIDEO-OUT connector.

*Note: this Green wire is ONLY used if CAN

connection does not switch display to

reverse image while in reverse properly.

1. With European radio keys, remove the MMI located in glove box. Disconnect any

associated harnesses and set the radio aside.

2. Grab the provided ‘Power/CAN Harness’ from the

DYNAMIC A3 kit. Connect the following wires to the car:

3. Locate the factory Pink (For AUDI’s with

NAV, this connector is GRAY), 4-pin round

connector that was removed from the
radio in step 1. Connect this factory plug to
the A3 interface at the port labeled ‘VIDEO
OUT’.*

4. Connect the smaller white

plug side of the provided
LVDS Video Cable to the
port on the A3 interface
labeled ‘VIDEO-IN’.

BHM

11/20/15

NTV-DOC244

Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.

3 | P a g e