NAV-TRACK UCT-DIFF CAM, NTV-KIT314 User Manual

BM

Plug & Play

Harness

NTV-HAR186

Overview

Kit Contents

UCT DIFF-CAM

NTV-ASY185

03/25/14

NTV-DOC093

3950 NW 120th Ave, Coral Springs, FL 33065 TEL [phone] FAX [phone]

www.nav-tv.com [e-mail]

UCT-DIFF CAM

NTV-KIT314

For select uConnect 8.4” vehicles: Allows for aftermarket rear camera to be installed into
vehicle. Converts composite video standard to differential video (Chrysler/Dodge standard).

(NTV-KIT297: UCT-84 Kit required for switching, UCT84 module requires software
adjustment).

Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.

1 | P a g e

BM

Installation

Rear of uConnect radio

Fig 1

Connect DIFF Cam

Harness here

03/25/14

NTV-DOC093

1. Remove the radio (only) from the dashboard. This usually requires pulling some

panels and a series of screws will hold the radio into the sub-dash.

2. Disconnect all harness from the radio and set the radio aside.

3. Reprogram the UCT84 module, make certain that the ‘Rear view camera’ flag is set

to ‘ON’.

4. Reconnect the UCT84 module into the vehicle.

5. Connect the white plug from the provided DIFF Cam Harness (see figure 1 at the

bottom of this page) to the radio.

6. Connect the camera’s signal RCA to the female RCA labeled ‘R

CAM’.

7. Plug the DIFF Cam R1 board into the 14-pin connector

located on the DIFF Cam harness.

8. Connect the Blue/White wire (combined with Gray/Black

wire) to Output 2 of the UCT84 module (White/Blue, pin 12).

9. If using Output 1 (ACC OUT, White/Red, pin 11) from the UCT-84 to power the

camera, be sure to utilize a relay!

10. Reconnect the remaining plugs to the radio, remount and test for proper operation.

Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for

misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.

2 | P a g e

BM

DIFF-CAM Pin Out

UCT DIFF-CAM Diagram

Pin #

Description

Color 3 Ground (-)

Black

6

Reverse Input (combines w/ pin 8)

Gray/Black

8

Reverse Input (combines w/ pin 6)

Blue/White

9

Composite Shield

[shield]

10

Composite Signal

Yellow

12

DIFF (+) to radio

Brown/White

13

DIFF (-) to radio

Brown

Wire side

If using Output 1 (ACC OUT, White/Red, pin 11) from the UCT-84 to power the
camera, be sure to utilize a relay!

03/25/14

NTV-DOC093

Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for

misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.

3 | P a g e

BM

DIFF-CAM Operation

UCT84 Module (not included) Programming

The UCT84 ships with Rear view camera ‘OFF’

03/25/14

NTV-DOC093

Rear view camera is enabled through the module programming before installation. Whenever
the vehicle is placed into reverse, the screen will switch to the attached rear camera.

Forced backup camera is not currently supported. This may be available in a future update. It
will currently only work in reverse.

The UCT84 module is shipped with Video in Motion (VIM) enabled and backup camera
disabled. Any changes to the module’s configuration should be done before installation. The

files needed to change the configuration can be found at

http://www.navtv.com/page/19/downloads.html. Be sure to follow installation instructions of

the software prior to connecting the
module to your computer.

Video in motion; address input in motion:

In the “ON” state, video from the DVD

player will be available while the vehicle is
in motion. Along with navigation input in
motion and Bluetooth control.
If this feature is disabled, all the above
features will work in the factory operation.

Rear view camera: In the “ON” state, the
backup camera port is available. When the
vehicle is placed into reverse the screen
will display the backup camera image
(requires optional camera harness).

Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.

4 | P a g e